shuttle an50r Motherboard and Linux
Hi. I have had a couple of problems trying to get this Motherboard to work correctly under Linux.
The Ethernet 10/100 is supposed to be an RC82540m, but the e100 module does not recognize it. If you do an lspci it doesn't say Intel at all, but just Nvidia and Shuttle. Am I doing something wrong, or is there a better driver in 2.6 than 2.4 or what?
Also, I am using the amd74xx driver for the chip set, but it does not seem to activate dma or announce udma and a number as the via one does -- is this the correct driver?
Any assistance would be appreciated.
Signature · 2 lines
John Covici
[email protected]Hi,
Quoted 11 lines · John Covici
Hi. I have had a couple of problems trying to get this Motherboard to work correctly under Linux.
The Ethernet 10/100 is supposed to be an RC82540m, but the e100 module does not recognize it. If you do an lspci it doesn't say Intel at all, but just Nvidia and Shuttle. Am I doing something wrong, or is there a better driver in 2.6 than 2.4 or what?
Also, I am using the amd74xx driver for the chip set, but it does not seem to activate dma or announce udma and a number as the via one does -- is this the correct driver?
What kernel version(s) are you using?
What are the boot messages ('dmesg' command output)? What is the output of 'lspci' command?
Regards,
Bartlomiej
OK, here are the relevant parts of the lspci -v -- I have been using 2.4.22, but if it will make a difference I will try newer ones.
00:00.0 Host bridge: nVidia Corporation nForce3 Host Bridge (rev a4)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device a550
Flags: bus master, 66Mhz, fast devsel, latency 0
Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] #08 [0180]
Capabilities: [c0] AGP version 3.0
00:01.0 ISA bridge: nVidia Corporation nForce3 LPC Bridge (rev a6)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device a550
Flags: bus master, 66Mhz, fast devsel, latency 0
00:01.1 SMBus: nVidia Corporation nForce3 SMBus (rev a4)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device a550
Flags: 66Mhz, fast devsel, IRQ 5
I/O ports at 4c00 [size=64]
I/O ports at 4c40 [size=64]
Capabilities: [44] Power Management version 2
00:05.0 Ethernet controller: nVidia Corporation nForce3 Ethernet (rev a5)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device a550
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 5 Memory at e8000000 (32-bit, non-prefetchable) [size=4K]
I/O ports at d000 [size=8]
Capabilities: [44] Power Management version 2
on Monday 03/08/2004 Bartlomiej Zolnierkiewicz([email protected]) wrote
Quoted 22 lines
Hi,
Quoted 11 lines · John Covici
Hi. I have had a couple of problems trying to get this Motherboard to work correctly under Linux.
The Ethernet 10/100 is supposed to be an RC82540m, but the e100 module does not recognize it. If you do an lspci it doesn't say Intel at all, but just Nvidia and Shuttle. Am I doing something wrong, or is there a better driver in 2.6 than 2.4 or what?
Also, I am using the amd74xx driver for the chip set, but it does not seem to activate dma or announce udma and a number as the via one does -- is this the correct driver?
What kernel version(s) are you using?
What are the boot messages ('dmesg' command output)? What is the output of 'lspci' command?Regards,
Bartlomiej
Signature · 2 lines
John Covici
[email protected]Quoted 1 line · John covici
OK, here are the relevant parts of the lspci -v -- I have been using
IDE interface is missed.
Quoted 1 line
2.4.22, but if it will make a difference I will try newer ones.
2.4.x needs update of amd74xx.c driver. 2.6.x should be okay.
Bartlomiej
Sorry, here it is.
00:08.0 IDE interface: nVidia Corporation nForce3 IDE (rev a5) (prog-if 8a [Master SecP PriP])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device a550
Flags: bus master, 66Mhz, fast devsel, latency 0
I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
on Monday 03/08/2004 Bartlomiej Zolnierkiewicz([email protected]) wrote
Quoted 10 lines · John covici
Quoted 1 line
OK, here are the relevant parts of the lspci -v -- I have been using
IDE interface is missed.
Quoted 1 line
2.4.22, but if it will make a difference I will try newer ones.
2.4.x needs update of
amd74xx.cdriver. 2.6.x should be okay.Bartlomiej
Signature · 2 lines
John Covici
[email protected]OK, I have just tried 2.6.2 and although it recognizes the chip, it sets all the disks to udma33 whereas I know at least two of them will work at 133.
Any ideas?
Quoted 28 lines · on Mon, 8 Mar 2004 10:37:47 -0500 John covici <[email protected]> wrote:
Sorry, here it is.
00:08.0 IDE interface: nVidia Corporation nForce3 IDE (rev a5) (prog-if 8a [Master SecP PriP])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device a550
Flags: bus master, 66Mhz, fast devsel, latency 0
I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2on Monday 03/08/2004 Bartlomiej Zolnierkiewicz([email protected]) wrote
Quoted 10 lines · John covici
Quoted 1 line
OK, here are the relevant parts of the lspci -v -- I have been using
IDE interface is missed.
Quoted 1 line
2.4.22, but if it will make a difference I will try newer ones.
2.4.x needs update of
amd74xx.cdriver. 2.6.x should be okay.Bartlomiej
Signature · 7 lines
John Covici [email protected] - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Signature · 2 lines
John Covici
[email protected]