Skip to contentSkip to conversation

bareudp: use ipv6_mod_enabled to check if IPv6 enabled

PATCH Applied Hangbin Liu 2 participants 2 messages Mar 15, 2022 – Mar 17, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 bareudp: use ipv6_mod_enabled to check if IPv6 enabled

bareudp_create_sock() use AF_INET6 by default if IPv6 CONFIG enabled. But if user start kernel with ipv6.disable=1, the bareudp sock will created failed, which cause the interface open failed even with ethertype ip. e.g.

 # ip link add bareudp1 type bareudp dstport 2 ethertype ip
 # ip link set bareudp1 up
 RTNETLINK answers: Address family not supported by protocol

Fix it by using ipv6_mod_enabled() to check if IPv6 enabled. There is no need to check IS_ENABLED(CONFIG_IPV6) as ipv6_mod_enabled() will return false when CONFIG_IPV6 no enabled in include/linux/ipv6.h.

Fixes 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
---
 drivers/net/bareudp.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)
drivers/net/bareudp.c +10 -9
index ba587e5fc24f..683203f87ae2 100644
@@ -148,14 +148,14 @@ static int bareudp_udp_encap_recv(struct sock *sk, struct sk_buff *skb)
 	skb_reset_network_header(skb);
 	skb_reset_mac_header(skb);
 
-	if (!IS_ENABLED(CONFIG_IPV6) || family == AF_INET)
+	if (!ipv6_mod_enabled() || family == AF_INET)
 		err = IP_ECN_decapsulate(oiph, skb);
 	else
 		err = IP6_ECN_decapsulate(oiph, skb);
 
 	if (unlikely(err)) {
 		if (log_ecn_error) {
-			if  (!IS_ENABLED(CONFIG_IPV6) || family == AF_INET)
+			if  (!ipv6_mod_enabled() || family == AF_INET)
 				net_info_ratelimited("non-ECT from %pI4 "
 						     "with TOS=%#x\n",
 						     &((struct iphdr *)oiph)->saddr,
@@ -221,11 +221,12 @@ static struct socket *bareudp_create_sock(struct net *net, __be16 port)
 	int err;
 
 	memset(&udp_conf, 0, sizeof(udp_conf));
-#if IS_ENABLED(CONFIG_IPV6)
-	udp_conf.family = AF_INET6;
-#else
-	udp_conf.family = AF_INET;
-#endif
+
+	if (ipv6_mod_enabled())
+		udp_conf.family = AF_INET6;
+	else
+		udp_conf.family = AF_INET;
+
 	udp_conf.local_udp_port = port;
 	/* Open UDP socket */
 	err = udp_sock_create(net, &udp_conf, &sock);
@@ -448,7 +449,7 @@ static netdev_tx_t bareudp_xmit(struct sk_buff *skb, struct net_device *dev)
 	}
 
 	rcu_read_lock();
-	if (IS_ENABLED(CONFIG_IPV6) && info->mode & IP_TUNNEL_INFO_IPV6)
+	if (ipv6_mod_enabled() && info->mode & IP_TUNNEL_INFO_IPV6)
 		err = bareudp6_xmit_skb(skb, dev, bareudp, info);
 	else
 		err = bareudp_xmit_skb(skb, dev, bareudp, info);
@@ -478,7 +479,7 @@ static int bareudp_fill_metadata_dst(struct net_device *dev,
 
 	use_cache = ip_tunnel_dst_cache_usable(skb, info);
 
-	if (!IS_ENABLED(CONFIG_IPV6) || ip_tunnel_info_af(info) == AF_INET) {
+	if (!ipv6_mod_enabled() || ip_tunnel_info_af(info) == AF_INET) {
 		struct rtable *rt;
 		__be32 saddr;
 
Signature · 1 line
2.35.1
#1 lore raw
This patch was applied to netdev/net-next.git (master) by Jakub Kicinski <[email protected]>:

Hello:

This patch was applied to netdev/net-next.git (master) by Jakub Kicinski <[email protected]>:

Quoted 10 lines · On Tue, 15 Mar 2022 14:26:18 +0800 you wrote:

bareudp_create_sock() use AF_INET6 by default if IPv6 CONFIG enabled. But if user start kernel with ipv6.disable=1, the bareudp sock will created failed, which cause the interface open failed even with ethertype ip. e.g.

 # ip link add bareudp1 type bareudp dstport 2 ethertype ip
 # ip link set bareudp1 up
 RTNETLINK answers: Address family not supported by protocol

[...]

Here is the summary with links:
- [net] bareudp: use ipv6_mod_enabled to check if IPv6 enabled

    https://git.kernel.org/netdev/net-next/c/e077ed58c243

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html