usb: dwc3: add power down scale setting
Subsystems (2)
PATCH v3 1/1 usb: dwc3: add power down scale setting
Some SoC(e.g NXP imx8MQ) may have a wrong default power down scale setting so need init it to be the correct value, the power down scale setting description in DWC3 databook:
Power Down Scale (PwrDnScale)
The USB3 suspend_clk input replaces pipe3_rx_pclk as a clock source to a small part of the USB3 core that operates when the SS PHY is in its lowest power (P3) state, and therefore does not provide a clock. The Power Down Scale field specifies how many suspend_clk periods fit into a 16 kHz clock period. When performing the division, round up the remainder.
For example, when using an 8-bit/16-bit/32-bit PHY and 25-MHz Suspend clock,
Power Down Scale = 25000 kHz/16 kHz = 13'd1563 (rounder up)
So use the suspend clock rate to calculate it.
---
Changes for v3:
- Refine the code comments for why we need do this as Thinh suggested.
- Add Thinh's R-b tag.
Changes for v2:
- Add PwrDnScale field update condition: less than the calculated value or more than 3x the calculated value.
- Correct 16k from 16384 to 16000.
- Delare variables in separate lines.
drivers/usb/dwc3/core.c | 34 ++++++++++++++++++++++++++++++++++ drivers/usb/dwc3/core.h | 1 + 2 files changed, 35 insertions(+)
drivers/usb/dwc3/core.c +34 -0
@@ -1029,6 +1029,37 @@ static void dwc3_set_incr_burst_type(struct dwc3 *dwc)dwc3_writel (dwc->regs,DWC3_GSBUSCFG0 , cfg); } +static void dwc3_set_power_down_clk_scale (struct dwc3 *dwc) +{ +u32 scale; +u32 reg; + +if (!dwc->susp_clk) +return ; + +/* +* The power down scale field specifies how many suspend_clk +* periods fit into a 16KHz clock period. When performing +* the division, round up the remainder. +* +* The power down scale value is calculated using the fastest +* frequency of the suspend_clk. If it isn't fixed (but within +* the accuracy requirement), the driver may not know the max +* rate of the suspend_clk, so only update the power down scale +* if the default is less than the calculated value from +* clk_get_rate() or if the default is questionably high +* (3x or more) to be within the requirement. +*/ + scale =DIV_ROUND_UP (clk_get_rate (dwc->susp_clk),16000 ); + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); +if ((reg &DWC3_GCTL_PWRDNSCALE_MASK ) <DWC3_GCTL_PWRDNSCALE (scale) || + (reg &DWC3_GCTL_PWRDNSCALE_MASK ) >DWC3_GCTL_PWRDNSCALE (scale*3 )) { + reg &= ~(DWC3_GCTL_PWRDNSCALE_MASK ); + reg |=DWC3_GCTL_PWRDNSCALE (scale); +dwc3_writel (dwc->regs,DWC3_GCTL , reg); + } +} +/** * dwc3_core_init - Low-level initialization of DWC3 Core * @dwc: Pointer to our controller context structure
@@ -1105,6 +1136,9 @@ static int dwc3_core_init(struct dwc3 *dwc)if (ret) goto err1; +/* Set power down scale of suspend_clk */ +dwc3_set_power_down_clk_scale (dwc); +/* Adjust Frame Length */ dwc3_frame_length_adjustment (dwc);
drivers/usb/dwc3/core.h +1 -0
@@ -231,6 +231,7 @@/* Global Configuration Register */ #define DWC3_GCTL_PWRDNSCALE (n) ((n) << 19) +#define DWC3_GCTL_PWRDNSCALE_MASK GENMASK(31, 19)#define DWC3_GCTL_U2RSTECN BIT(16)#define DWC3_GCTL_RAMCLKSEL (x) (((x) & DWC3_GCTL_CLK_MASK) << 6)#define DWC3_GCTL_CLK_BUS (0)
Signature · 1 line
2.25.1