Skip to contentSkip to conversation

net: lan743x: PCI11010 / PCI11414 devices Enhancements

PATCH Applied Raju Lakkaraju 3 participants 10 messages Jun 16, 2022 – Jun 17, 2022

Subsystems (5)

v2 of 7 Applied 4/4 Latest is v7 →

lore
Share & tools
lore
#0 lore raw

v2 cover net: lan743x: PCI11010 / PCI11414 devices Enhancements

This patch series continues with the addition of supported features for the Ethernet function of the PCI11010 / PCI11414 devices to the LAN743x driver.

Raju Lakkaraju (4):
net: lan743x: Add support to LAN743x register dump
net: lan743x: Add support to Secure-ON WOL
net: lan743x: Add support to SGMII 1G and 2.5G
net: phy: add support to get Master-Slave configuration

 .../net/ethernet/microchip/lan743x_ethtool.c  |  63 ++-
 .../net/ethernet/microchip/lan743x_ethtool.h  |  26 ++
 drivers/net/ethernet/microchip/lan743x_main.c | 378 +++++++++++++++++-
 drivers/net/ethernet/microchip/lan743x_main.h | 106 +++++
 drivers/net/phy/mxl-gpy.c                     |   3 +
 5 files changed, 567 insertions(+), 9 deletions(-)
Signature · 1 line
2.25.1
#1 lore raw

PATCH v2 1/4 net: lan743x: Add support to LAN743x register dump

Add support to LAN743x common register dump

---
 .../net/ethernet/microchip/lan743x_ethtool.c  | 45 +++++++++++++++++++
 .../net/ethernet/microchip/lan743x_ethtool.h  | 26 +++++++++++
 2 files changed, 71 insertions(+)
drivers/net/ethernet/microchip/lan743x_ethtool.c +45 -0
index c8fe8b31f07b..48b19dcd4351 100644
@@ -1178,6 +1178,49 @@ static int lan743x_ethtool_set_wol(struct net_device *netdev,
 }
 #endif /* CONFIG_PM */
 
+static void lan743x_common_regs(struct net_device *dev,
+				struct ethtool_regs *regs, void *p)
+
+{
+	struct lan743x_adapter *adapter = netdev_priv(dev);
+	u32 *rb = p;
+
+	memset(p, 0, (MAX_LAN743X_ETH_REGS * sizeof(u32)));
+
+	rb[ETH_PRIV_FLAGS] = adapter->flags;
+	rb[ETH_ID_REV]     = lan743x_csr_read(adapter, ID_REV);
+	rb[ETH_FPGA_REV]   = lan743x_csr_read(adapter, FPGA_REV);
+	rb[ETH_STRAP_READ] = lan743x_csr_read(adapter, STRAP_READ);
+	rb[ETH_INT_STS]    = lan743x_csr_read(adapter, INT_STS);
+	rb[ETH_HW_CFG]     = lan743x_csr_read(adapter, HW_CFG);
+	rb[ETH_PMT_CTL]    = lan743x_csr_read(adapter, PMT_CTL);
+	rb[ETH_E2P_CMD]    = lan743x_csr_read(adapter, E2P_CMD);
+	rb[ETH_E2P_DATA]   = lan743x_csr_read(adapter, E2P_DATA);
+	rb[ETH_MAC_CR]     = lan743x_csr_read(adapter, MAC_CR);
+	rb[ETH_MAC_RX]     = lan743x_csr_read(adapter, MAC_RX);
+	rb[ETH_MAC_TX]     = lan743x_csr_read(adapter, MAC_TX);
+	rb[ETH_FLOW]       = lan743x_csr_read(adapter, MAC_FLOW);
+	rb[ETH_MII_ACC]    = lan743x_csr_read(adapter, MAC_MII_ACC);
+	rb[ETH_MII_DATA]   = lan743x_csr_read(adapter, MAC_MII_DATA);
+	rb[ETH_EEE_TX_LPI_REQ_DLY]  = lan743x_csr_read(adapter,
+						       MAC_EEE_TX_LPI_REQ_DLY_CNT);
+	rb[ETH_WUCSR]      = lan743x_csr_read(adapter, MAC_WUCSR);
+	rb[ETH_WK_SRC]     = lan743x_csr_read(adapter, MAC_WK_SRC);
+}
+
+static int lan743x_get_regs_len(struct net_device *dev)
+{
+	return MAX_LAN743X_ETH_REGS * sizeof(u32);
+}
+
+static void lan743x_get_regs(struct net_device *dev,
+			     struct ethtool_regs *regs, void *p)
+{
+	regs->version = LAN743X_ETH_REG_VERSION;
+
+	lan743x_common_regs(dev, regs, p);
+}
+
 const struct ethtool_ops lan743x_ethtool_ops = {
 	.get_drvinfo = lan743x_ethtool_get_drvinfo,
 	.get_msglevel = lan743x_ethtool_get_msglevel,
@@ -1202,6 +1245,8 @@ const struct ethtool_ops lan743x_ethtool_ops = {
 	.set_eee = lan743x_ethtool_set_eee,
 	.get_link_ksettings = phy_ethtool_get_link_ksettings,
 	.set_link_ksettings = phy_ethtool_set_link_ksettings,
+	.get_regs_len = lan743x_get_regs_len,
+	.get_regs = lan743x_get_regs,
 #ifdef CONFIG_PM
 	.get_wol = lan743x_ethtool_get_wol,
 	.set_wol = lan743x_ethtool_set_wol,
drivers/net/ethernet/microchip/lan743x_ethtool.h +26 -0
index d0d11a777a58..7f5996a52488 100644
@@ -6,6 +6,32 @@
 
 #include "linux/ethtool.h"
 
+#define LAN743X_ETH_REG_VERSION         1
+
+enum {
+	ETH_PRIV_FLAGS,
+	ETH_ID_REV,
+	ETH_FPGA_REV,
+	ETH_STRAP_READ,
+	ETH_INT_STS,
+	ETH_HW_CFG,
+	ETH_PMT_CTL,
+	ETH_E2P_CMD,
+	ETH_E2P_DATA,
+	ETH_MAC_CR,
+	ETH_MAC_RX,
+	ETH_MAC_TX,
+	ETH_FLOW,
+	ETH_MII_ACC,
+	ETH_MII_DATA,
+	ETH_EEE_TX_LPI_REQ_DLY,
+	ETH_WUCSR,
+	ETH_WK_SRC,
+
+	/* Add new registers above */
+	MAX_LAN743X_ETH_REGS
+};
+
 extern const struct ethtool_ops lan743x_ethtool_ops;
 
 #endif /* _LAN743X_ETHTOOL_H */
Signature · 1 line
2.25.1
#3 lore raw

PATCH v2 2/4 net: lan743x: Add support to Secure-ON WOL

In reply to Raju Lakkaraju

Add support to Magic Packet Detection with Secure-ON for PCI11010/PCI11414 chips

---
Changes:
V0 -> V1:
1. Change to sizeof(wol->sopass) instead of SOPASS_MAX * sizeof(wol->sopass[0])

 .../net/ethernet/microchip/lan743x_ethtool.c  | 12 ++++++++
 drivers/net/ethernet/microchip/lan743x_main.c | 29 +++++++++++++++++++
 drivers/net/ethernet/microchip/lan743x_main.h | 10 +++++++
 3 files changed, 51 insertions(+)
drivers/net/ethernet/microchip/lan743x_ethtool.c +12 -0
index 48b19dcd4351..99776f7b64aa 100644
@@ -1149,7 +1149,12 @@ static void lan743x_ethtool_get_wol(struct net_device *netdev,
 	wol->supported |= WAKE_BCAST | WAKE_UCAST | WAKE_MCAST |
 		WAKE_MAGIC | WAKE_PHY | WAKE_ARP;
 
+	if (adapter->is_pci11x1x)
+		wol->supported |= WAKE_MAGICSECURE;
+
 	wol->wolopts |= adapter->wolopts;
+	if (adapter->wolopts & WAKE_MAGICSECURE)
+		memcpy(wol->sopass, adapter->sopass, sizeof(wol->sopass));
 }
 
 static int lan743x_ethtool_set_wol(struct net_device *netdev,
@@ -1170,6 +1175,13 @@ static int lan743x_ethtool_set_wol(struct net_device *netdev,
 		adapter->wolopts |= WAKE_PHY;
 	if (wol->wolopts & WAKE_ARP)
 		adapter->wolopts |= WAKE_ARP;
+	if (wol->wolopts & WAKE_MAGICSECURE &&
+	    wol->wolopts & WAKE_MAGIC) {
+		memcpy(adapter->sopass, wol->sopass, sizeof(wol->sopass));
+		adapter->wolopts |= WAKE_MAGICSECURE;
+	} else {
+		memset(adapter->sopass, 0, sizeof(u8) * SOPASS_MAX);
+	}
 
 	device_set_wakeup_enable(&adapter->pdev->dev, (bool)wol->wolopts);
 
drivers/net/ethernet/microchip/lan743x_main.c +29 -0
index af81236b4b4e..6352cba19691 100644
@@ -3124,6 +3124,7 @@ static void lan743x_pm_set_wol(struct lan743x_adapter *adapter)
 	const u8 ipv6_multicast[3] = { 0x33, 0x33 };
 	const u8 arp_type[2] = { 0x08, 0x06 };
 	int mask_index;
+	u32 sopass;
 	u32 pmtctl;
 	u32 wucsr;
 	u32 macrx;
@@ -3218,6 +3219,14 @@ static void lan743x_pm_set_wol(struct lan743x_adapter *adapter)
 		pmtctl |= PMT_CTL_RX_FCT_RFE_D3_CLK_OVR_;
 	}
 
+	if (adapter->wolopts & WAKE_MAGICSECURE) {
+		sopass = *(u32 *)adapter->sopass;
+		lan743x_csr_write(adapter, MAC_MP_SO_LO, sopass);
+		sopass = *(u16 *)&adapter->sopass[4];
+		lan743x_csr_write(adapter, MAC_MP_SO_HI, sopass);
+		wucsr |= MAC_MP_SO_EN_;
+	}
+
 	lan743x_csr_write(adapter, MAC_WUCSR, wucsr);
 	lan743x_csr_write(adapter, PMT_CTL, pmtctl);
 	lan743x_csr_write(adapter, MAC_RX, macrx);
@@ -3228,6 +3237,7 @@ static int lan743x_pm_suspend(struct device *dev)
 	struct pci_dev *pdev = to_pci_dev(dev);
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct lan743x_adapter *adapter = netdev_priv(netdev);
+	u32 data;
 
 	lan743x_pcidev_shutdown(pdev);
 
@@ -3239,6 +3249,18 @@ static int lan743x_pm_suspend(struct device *dev)
 	if (adapter->wolopts)
 		lan743x_pm_set_wol(adapter);
 
+	if (adapter->is_pci11x1x) {
+		/* Save HW_CFG to config again in PM resume */
+		data = lan743x_csr_read(adapter, HW_CFG);
+		adapter->hw_cfg = data;
+		data |= (HW_CFG_RST_PROTECT_PCIE_ |
+			 HW_CFG_D3_RESET_DIS_ |
+			 HW_CFG_D3_VAUX_OVR_ |
+			 HW_CFG_HOT_RESET_DIS_ |
+			 HW_CFG_RST_PROTECT_);
+		lan743x_csr_write(adapter, HW_CFG, data);
+	}
+
 	/* Host sets PME_En, put D3hot */
 	return pci_prepare_to_sleep(pdev);
 }
@@ -3254,6 +3276,10 @@ static int lan743x_pm_resume(struct device *dev)
 	pci_restore_state(pdev);
 	pci_save_state(pdev);
 
+	/* Restore HW_CFG that was saved during pm suspend */
+	if (adapter->is_pci11x1x)
+		lan743x_csr_write(adapter, HW_CFG, adapter->hw_cfg);
+
 	ret = lan743x_hardware_init(adapter, pdev);
 	if (ret) {
 		netif_err(adapter, probe, adapter->netdev,
@@ -3270,6 +3296,9 @@ static int lan743x_pm_resume(struct device *dev)
 		lan743x_netdev_open(netdev);
 
 	netif_device_attach(netdev);
+	ret = lan743x_csr_read(adapter, MAC_WK_SRC);
+	netif_info(adapter, drv, adapter->netdev,
+		   "Wakeup source : 0x%08X\n", ret);
 
 	return 0;
 }
drivers/net/ethernet/microchip/lan743x_main.h +10 -0
index 1ca5f3216403..5d37263b25c8 100644
@@ -43,6 +43,11 @@
 #define STRAP_READ_ADV_PM_DISABLE_	BIT(0)
 
 #define HW_CFG					(0x010)
+#define HW_CFG_RST_PROTECT_PCIE_		BIT(19)
+#define HW_CFG_HOT_RESET_DIS_			BIT(15)
+#define HW_CFG_D3_VAUX_OVR_			BIT(14)
+#define HW_CFG_D3_RESET_DIS_			BIT(13)
+#define HW_CFG_RST_PROTECT_			BIT(12)
 #define HW_CFG_RELOAD_TYPE_ALL_			(0x00000FC0)
 #define HW_CFG_EE_OTP_RELOAD_			BIT(4)
 #define HW_CFG_LRST_				BIT(1)
@@ -214,6 +219,7 @@
 #define MAC_EEE_TX_LPI_REQ_DLY_CNT		(0x130)
 
 #define MAC_WUCSR				(0x140)
+#define MAC_MP_SO_EN_				BIT(21)
 #define MAC_WUCSR_RFE_WAKE_EN_			BIT(14)
 #define MAC_WUCSR_PFDA_EN_			BIT(3)
 #define MAC_WUCSR_WAKE_EN_			BIT(2)
@@ -221,6 +227,8 @@
 #define MAC_WUCSR_BCST_EN_			BIT(0)
 
 #define MAC_WK_SRC				(0x144)
+#define MAC_MP_SO_HI				(0x148)
+#define MAC_MP_SO_LO				(0x14C)
 
 #define MAC_WUF_CFG0			(0x150)
 #define MAC_NUM_OF_WUF_CFG		(32)
@@ -912,6 +920,7 @@ struct lan743x_adapter {
 	int                     msg_enable;
 #ifdef CONFIG_PM
 	u32			wolopts;
+	u8			sopass[SOPASS_MAX];
 #endif
 	struct pci_dev		*pdev;
 	struct lan743x_csr      csr;
@@ -937,6 +946,7 @@ struct lan743x_adapter {
 
 #define LAN743X_ADAPTER_FLAG_OTP		BIT(0)
 	u32			flags;
+	u32			hw_cfg;
 };
 
 #define LAN743X_COMPONENT_FLAG_RX(channel)  BIT(20 + (channel))
Signature · 1 line
2.25.1
#5 lore raw

PATCH v2 3/4 net: lan743x: Add support to SGMII 1G and 2.5G

In reply to Raju Lakkaraju

Add SGMII access read and write functions
Add support to SGMII 1G and 2.5G for PCI11010/PCI11414 chips

---
V0 -> V1:
1. Remove the unlikely()
From Add support to SGMII 1G and 2.5G patch:
1. Use the MMD devices definitions from mdio.h file
2. Use MII definitions from mii.h

V1 -> V2:
1. Merge SGMII access functions patch and SGMII 1G and 2.5G patch into one patch

 .../net/ethernet/microchip/lan743x_ethtool.c  |   6 +-
 drivers/net/ethernet/microchip/lan743x_main.c | 349 +++++++++++++++++-
 drivers/net/ethernet/microchip/lan743x_main.h |  96 +++++
 3 files changed, 442 insertions(+), 9 deletions(-)
drivers/net/ethernet/microchip/lan743x_ethtool.c +3 -3
index 99776f7b64aa..b1c74e6cb012 100644
@@ -155,8 +155,8 @@ static int lan743x_otp_write(struct lan743x_adapter *adapter, u32 offset,
 	return 0;
 }
 
-static int lan743x_hs_syslock_acquire(struct lan743x_adapter *adapter,
-				      u16 timeout)
+int lan743x_hs_syslock_acquire(struct lan743x_adapter *adapter,
+			       u16 timeout)
 {
 	u16 timeout_cnt = 0;
 	u32 val;
@@ -192,7 +192,7 @@ static int lan743x_hs_syslock_acquire(struct lan743x_adapter *adapter,
 	return 0;
 }
 
-static void lan743x_hs_syslock_release(struct lan743x_adapter *adapter)
+void lan743x_hs_syslock_release(struct lan743x_adapter *adapter)
 {
 	u32 val;
 
drivers/net/ethernet/microchip/lan743x_main.c +343 -6

399 lines not on this page · raw message

drivers/net/ethernet/microchip/lan743x_main.h +96 -0

130 lines not on this page · raw message

Signature · 1 line
2.25.1
#7 lore raw

PATCH v2 4/4 net: phy: add support to get Master-Slave configuration

In reply to Raju Lakkaraju

Add support to Master-Slave configuration and state

---
Changes:
V0 -> V1:
1. Remove the gpy_master_slave_cfg_get() function and use the
genphy_read_master_slave() funtion.

 drivers/net/phy/mxl-gpy.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/net/phy/mxl-gpy.c +3 -0
index 5ce1bf03bbd7..6c4da2f9e90a 100644
@@ -295,6 +295,9 @@ static void gpy_update_interface(struct phy_device *phydev)
 				   ret);
 		break;
 	}
+
+	if (phydev->speed == SPEED_2500 || phydev->speed == SPEED_1000)
+		genphy_read_master_slave(phydev);
 }
 
 static int gpy_read_status(struct phy_device *phydev)
Signature · 1 line
2.25.1
maintainer Reviewed-by on v2 4/4
#8 lore raw

Re: [PATCH net-next V2 4/4] net: phy: add support to get Master-Slave configuration

Quoted 8 lines · Raju Lakkaraju

Add support to Master-Slave configuration and state

---
Changes:
V0 -> V1:
1. Remove the gpy_master_slave_cfg_get() function and use the
genphy_read_master_slave() funtion.

So much easier isn't it to make use of existing helpers.

Andrew

#9 lore raw
In reply to Raju Lakkaraju
This series was applied to netdev/net-next.git (master) by Jakub Kicinski <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (master) by Jakub Kicinski <[email protected]>:

Quoted 11 lines · On Thu, 16 Jun 2022 09:42:22 +0530 you wrote:

This patch series continues with the addition of supported features for the Ethernet function of the PCI11010 / PCI11414 devices to the LAN743x driver.

Raju Lakkaraju (4):
net: lan743x: Add support to LAN743x register dump
net: lan743x: Add support to Secure-ON WOL
net: lan743x: Add support to SGMII 1G and 2.5G
net: phy: add support to get Master-Slave configuration

[...]

Here is the summary with links:
- [net-next,V2,1/4] net: lan743x: Add support to LAN743x register dump

    https://git.kernel.org/netdev/net-next/c/9aeb87d2b5a1
  - [net-next,V2,2/4] net: lan743x: Add support to Secure-ON WOL
    https://git.kernel.org/netdev/net-next/c/6b3768ac8e2b
  - [net-next,V2,3/4] net: lan743x: Add support to SGMII 1G and 2.5G
    https://git.kernel.org/netdev/net-next/c/46b777ad9a8c
  - [net-next,V2,4/4] net: phy: add support to get Master-Slave configuration
    https://git.kernel.org/netdev/net-next/c/311abcdddc00

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html