Skip to contentSkip to conversation

net: phy: Don't trigger state machine while in suspend

PATCH Applied Lukas Wunner 3 participants 3 messages Jun 28, 2022 – Jun 30, 2022

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH v4 1/1 net: phy: Don't trigger state machine while in suspend

Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(), but subsequent interrupts may retrigger it:

They may have been left enabled to facilitate wakeup and are not quiesced until the ->suspend_noirq() phase. Unwanted interrupts may hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(), as well as between dpm_resume_noirq() and mdio_bus_phy_resume().

Retriggering the phy_state_machine() through an interrupt is not only undesirable for the reason given in mdio_bus_phy_suspend() (freezing it midway with phydev->lock held), but also because the PHY may be inaccessible after it's suspended: Accesses to USB-attached PHYs are blocked once usb_suspend_both() clears the can_submit flag and PHYs on PCI network cards may become inaccessible upon suspend as well.

Amend phy_interrupt() to avoid triggering the state machine if the PHY is suspended. Signal wakeup instead if the attached net_device or its parent has been configured as a wakeup source. (Those conditions are identical to mdio_bus_phy_may_suspend().) Postpone handling of the interrupt until the PHY has resumed.

Before stopping the phy_state_machine() in mdio_bus_phy_suspend(), wait for a concurrent phy_interrupt() to run to completion. That is necessary because phy_interrupt() may have checked the PHY's suspend status before the system sleep transition commenced and it may thus retrigger the state machine after it was stopped.

Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(), wait for a concurrent phy_interrupt() to complete to ensure that interrupts which it postponed are properly rerun.

The issue was exposed by commit 1ce8b37241ed ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling"), but has existed since forever.

---
Changes v3 -> v4:
* Fix sha1 in commit message
* Add correct Fixes tag

Changes v2 -> v3:
* Add stable designation
* Add Acked-by tag (Rafael)

Changes v1 -> v2:
* Extend rationale in commit message
* Drop incorrect Fixes tag, add Tested-by tag (Marek)

Link to v3:
https://lore.kernel.org/netdev/c5595bdb20625382538816c2e6d917d95c62e09b.1656322883.git.lukas@wunner.de/

 drivers/net/phy/phy.c        | 23 +++++++++++++++++++++++
 drivers/net/phy/phy_device.c | 23 +++++++++++++++++++++++
 include/linux/phy.h          |  6 ++++++
 3 files changed, 52 insertions(+)
drivers/net/phy/phy.c +23 -0
index ef62f357b76d..8d3ee3a6495b 100644
@@ -31,6 +31,7 @@
 #include <linux/io.h>
 #include <linux/uaccess.h>
 #include <linux/atomic.h>
+#include <linux/suspend.h>
 #include <net/netlink.h>
 #include <net/genetlink.h>
 #include <net/sock.h>
@@ -976,6 +977,28 @@ static irqreturn_t phy_interrupt(int irq, void *phy_dat)
 	struct phy_driver *drv = phydev->drv;
 	irqreturn_t ret;
 
+	/* Wakeup interrupts may occur during a system sleep transition.
+	 * Postpone handling until the PHY has resumed.
+	 */
+	if (IS_ENABLED(CONFIG_PM_SLEEP) && phydev->irq_suspended) {
+		struct net_device *netdev = phydev->attached_dev;
+
+		if (netdev) {
+			struct device *parent = netdev->dev.parent;
+
+			if (netdev->wol_enabled)
+				pm_system_wakeup();
+			else if (device_may_wakeup(&netdev->dev))
+				pm_wakeup_dev_event(&netdev->dev, 0, true);
+			else if (parent && device_may_wakeup(parent))
+				pm_wakeup_dev_event(parent, 0, true);
+		}
+
+		phydev->irq_rerun = 1;
+		disable_irq_nosync(irq);
+		return IRQ_HANDLED;
+	}
+
 	mutex_lock(&phydev->lock);
 	ret = drv->handle_interrupt(phydev);
 	mutex_unlock(&phydev->lock);
drivers/net/phy/phy_device.c +23 -0
index 431a8719c635..46acddd865a7 100644
@@ -278,6 +278,15 @@ static __maybe_unused int mdio_bus_phy_suspend(struct device *dev)
 	if (phydev->mac_managed_pm)
 		return 0;
 
+	/* Wakeup interrupts may occur during the system sleep transition when
+	 * the PHY is inaccessible. Set flag to postpone handling until the PHY
+	 * has resumed. Wait for concurrent interrupt handler to complete.
+	 */
+	if (phy_interrupt_is_valid(phydev)) {
+		phydev->irq_suspended = 1;
+		synchronize_irq(phydev->irq);
+	}
+
 	/* We must stop the state machine manually, otherwise it stops out of
 	 * control, possibly with the phydev->lock held. Upon resume, netdev
 	 * may call phy routines that try to grab the same lock, and that may
@@ -315,6 +324,20 @@ static __maybe_unused int mdio_bus_phy_resume(struct device *dev)
 	if (ret < 0)
 		return ret;
 no_resume:
+	if (phy_interrupt_is_valid(phydev)) {
+		phydev->irq_suspended = 0;
+		synchronize_irq(phydev->irq);
+
+		/* Rerun interrupts which were postponed by phy_interrupt()
+		 * because they occurred during the system sleep transition.
+		 */
+		if (phydev->irq_rerun) {
+			phydev->irq_rerun = 0;
+			enable_irq(phydev->irq);
+			irq_wake_thread(phydev->irq, phydev);
+		}
+	}
+
 	if (phydev->attached_dev && phydev->adjust_link)
 		phy_start_machine(phydev);
 
include/linux/phy.h +6 -0
index 508f1149665b..b09f7d36cff2 100644
@@ -572,6 +572,10 @@ struct macsec_ops;
  * @mdix_ctrl: User setting of crossover
  * @pma_extable: Cached value of PMA/PMD Extended Abilities Register
  * @interrupts: Flag interrupts have been enabled
+ * @irq_suspended: Flag indicating PHY is suspended and therefore interrupt
+ *                 handling shall be postponed until PHY has resumed
+ * @irq_rerun: Flag indicating interrupts occurred while PHY was suspended,
+ *             requiring a rerun of the interrupt handler after resume
  * @interface: enum phy_interface_t value
  * @skb: Netlink message for cable diagnostics
  * @nest: Netlink nest used for cable diagnostics
@@ -626,6 +630,8 @@ struct phy_device {
 
 	/* Interrupts are enabled */
 	unsigned interrupts:1;
+	unsigned irq_suspended:1;
+	unsigned irq_rerun:1;
 
 	enum phy_state state;
 
Signature · 1 line
2.36.1
maintainer Reviewed-by on v4 1/1
#1 lore raw
Quoted 35 lines · Lukas Wunner

Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(), but subsequent interrupts may retrigger it:

They may have been left enabled to facilitate wakeup and are not quiesced until the ->suspend_noirq() phase. Unwanted interrupts may hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(), as well as between dpm_resume_noirq() and mdio_bus_phy_resume().

Retriggering the phy_state_machine() through an interrupt is not only undesirable for the reason given in mdio_bus_phy_suspend() (freezing it midway with phydev->lock held), but also because the PHY may be inaccessible after it's suspended: Accesses to USB-attached PHYs are blocked once usb_suspend_both() clears the can_submit flag and PHYs on PCI network cards may become inaccessible upon suspend as well.

Amend phy_interrupt() to avoid triggering the state machine if the PHY is suspended. Signal wakeup instead if the attached net_device or its parent has been configured as a wakeup source. (Those conditions are identical to mdio_bus_phy_may_suspend().) Postpone handling of the interrupt until the PHY has resumed.

Before stopping the phy_state_machine() in mdio_bus_phy_suspend(), wait for a concurrent phy_interrupt() to run to completion. That is necessary because phy_interrupt() may have checked the PHY's suspend status before the system sleep transition commenced and it may thus retrigger the state machine after it was stopped.

Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(), wait for a concurrent phy_interrupt() to complete to ensure that interrupts which it postponed are properly rerun.

The issue was exposed by commit 1ce8b37241ed ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling"), but has existed since forever.

Quoted 7 lines

Andrew

#2 lore raw
In reply to Lukas Wunner
This patch was applied to netdev/net.git (master) by Jakub Kicinski <[email protected]>:

Hello:

This patch was applied to netdev/net.git (master)
by Jakub Kicinski <[email protected]>:

Quoted 9 lines · On Tue, 28 Jun 2022 12:15:08 +0200 you wrote:

Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(), but subsequent interrupts may retrigger it:

They may have been left enabled to facilitate wakeup and are not quiesced until the ->suspend_noirq() phase. Unwanted interrupts may hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(), as well as between dpm_resume_noirq() and mdio_bus_phy_resume().

[...]

Here is the summary with links:
- [net,v4] net: phy: Don't trigger state machine while in suspend

    https://git.kernel.org/netdev/net/c/1758bde2e4aa

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html