Skip to contentSkip to conversation

problems with multitech 4 port serial card under 2.4.x and 2.6.x

DISCUSSION John Covici 2 participants 4 messages Sep 17, 2004

lore
Share & tools
lore
#0 lore raw

I have had problems with the multitech 4 port serial card under both the 2.4 and the 2.6 Linux kernels.

I guess the most important problem is that the driver module does not detect the card at all -- the only driver whichworks is the one from
multitech itself. Here is the lspci -v entry for the card.

0000:00:0e.0 Serial controller: Exar Corp. XR17C158 Octal UART (rev
01) (prog-if 02 [16550])

        Subsystem: Unknown device 2205:2001
        Flags: fast devsel, IRQ 7
        Memory at fba00000 (32-bit, non-prefetchable) [size=2K]

Now also, I have an Asus a8V and if I have the apic support for uni processors on it won't even boot with the card installed.

Any assistance on these matters would be appreciated -- especially Any assistance on these matters would be appreciated.

Signature · 2 lines
         John Covici
         [email protected]
#1 lore raw
Quoted 2 lines · John Covici

I have had problems with the multitech 4 port serial card under both the 2.4 and the 2.6 Linux kernels.

You don't say which 2.6 kernel. Support for these UARTs has only recently been merged - you'll find it in 2.6.9-rc2 kernels.

Unfortunately I don't recall if it's in 2.6.9-rc1 or not.

Signature · 4 lines
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:  2.6 PCMCIA      - http://pcmcia.arm.linux.org.uk/
                 2.6 Serial core
#2 lore raw

Well, I was using 2.6.8 and there is under character devices a configuration which says multitech and it says its experimental, but it does not detect the card -- same with 2.4.26. Maybe I should try the rc2 and see if my apic problems go away as well -- which would be nice.

on Friday 09/17/2004 Russell King([email protected]) wrote

Quoted 19 lines · John Covici
Quoted 2 lines

I have had problems with the multitech 4 port serial card under both the 2.4 and the 2.6 Linux kernels.

You don't say which 2.6 kernel. Support for these UARTs has only recently been merged - you'll find it in 2.6.9-rc2 kernels.

Unfortunately I don't recall if it's in 2.6.9-rc1 or not.

Signature · 9 lines
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:  2.6 PCMCIA      - http://pcmcia.arm.linux.org.uk/
                 2.6 Serial core
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/
Signature · 2 lines
         John Covici
         [email protected]
#3 lore raw
In reply to Russell King

I found it in the changelog -- thanks much. I wonder why the board would freak out the apic stuff?

on Friday 09/17/2004 Russell King([email protected]) wrote

Quoted 14 lines · John Covici
Quoted 2 lines

I have had problems with the multitech 4 port serial card under both the 2.4 and the 2.6 Linux kernels.

You don't say which 2.6 kernel. Support for these UARTs has only recently been merged - you'll find it in 2.6.9-rc2 kernels.

Unfortunately I don't recall if it's in 2.6.9-rc1 or not.

Signature · 4 lines
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:  2.6 PCMCIA      - http://pcmcia.arm.linux.org.uk/
                 2.6 Serial core
Signature · 2 lines
         John Covici
         [email protected]