Skip to contentSkip to conversation

arm64: sunxi: Initial Allwinner H616 SoC support

PATCH Applied Andre Przywara 9 participants 41 messages Jan 27, 2021 – Feb 5, 2021

Subsystems (19)

v5 of 13 Applied Latest is v13 →

lore
Share & tools
lore
#0 lore raw

v5 cover arm64: sunxi: Initial Allwinner H616 SoC support

Hi,

this is a small update from v4, fixing some DT validation issues:
dtbs_check now comes back clean for me.
Also I dropped USB support for now. It turns out that this is more messy than we thought: it only works if all four USB controllers are enabled (and not just some PHYs). That smells like some shared reset or clock gate, but we haven't found the culprit yet. Also the BSP source suggests that there is a "hardware design issue" that requires some PHY tune register to be programmed, so we probably need more code anyway. I also dropped the DT node for the second EMAC, as this is mostly untested at this point.

Changelog below. Based on the (updated) sunxi/for-next branch.

I was hoping that at least the clock and AXP patches (01/20-06/20) could make it into 5.12 still? That would allow booting boards from SD card. Patch 08/20 would enable Ethernet.
U-Boot support is now merged into its master tree.

Thanks!
Andre

==================
This series gathers patches to support the Allwinner H616 SoC. This is a rather uninspired SoC (Quad-A53 with the usual peripherals), but allows for some cheap development boards and TV boxes, and supports up to 4GB of DRAM.

Various DT binding patches are sprinkled throughout the series, to add the new compatible names right before they are used.
Patch 2 and 3 add clock support. For the -R clock this is shared with the H6 code, as the clocks are identical, with the H616 just having fewer of them. The main clocks are different enough to warrant a separate file.
Patches 5 and 6 teach the AXP MFD driver to get along without having an interrupt, as the missing NMI pin on the H616 leads to some boards not having the AXP IRQ line connected.
Patch 8 and 16 add some tweaks to the syscon and EMAC driver, to deal with the second EMAC clock used for the second Ethernet controller. This is somewhat optional for the current .dts, as this doesn't use the second EMAC.

The remaining patches add DT bindings, which just add the new compatible string along with an existing name as a fallback string. Eventually we get the .dtsi for the SoC in patch 19, and the .dts for the OrangePi Zero2 board[1] in the last patch.

We have U-Boot and Trusted-Firmware support in a working state, booting via FEL or SD card and even TFTPing kernels work already [2][3]. The U-Boot patches are already merged into the mainline repository.

Many thanks to Jernej for his tremendous help on this, also for the awesome input and help from the #linux-sunxi Freenode channel.

The whole series (including the other patches) can also be found here:
https://github.com/apritzel/linux/commits/h616-v5

Happy reviewing!

Cheers,
Andre

[1] https://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
[2] https://github.com/jernejsk/u-boot/commits/h616-v2
[3] https://github.com/apritzel/arm-trusted-firmware/commits/h616-v1

Changelog v4 .. v5:
- Fix CCU binding to pass dtbs_check
- Add RSB compatible string to binding doc
- Rename IR pin name to pass dtbs_check
- Add EMAC compatible string to binding doc
- Drop USB PHY support and binding doc patches
- Drop USB nodes from .dtsi and .dts
- Drop second EMAC node from .dtsi

Changelog v3 .. v4:
- Drop MMC and pinctrl matches (already in some -next trees)
- Add Maxime's Acks
- Add patch to update the AXP MFD DT bindings
- Add new patch (05/21) to fix axp20x-pek driver
- Change AXP IRQ fix to check for invalid IRQ line number
- Split joint DT bindings patch (v3 18/21) into subsystems
- move dwmac variable to keep christmas tree
- Use enums for USB PHY compatible strings in DT binding
- Enable watchdog (briefly verified to work)
- Add PHY2 to HCI1&3, this fixes USB
- limit r-ccu register frame length to not collide with NMI controller
- add interrupt-controller property to AXP DT node

Changelog v2 .. v3:
- Add Rob's Acks
- Drop redundant maxItems from pinctrl DT binding
- Rename h_i2s* to just i2s* in pinctrl names
- Use more declarative i2s0_d{in,out}{0,1} names
- Add RSB pins to pinctrl
- Include RSB clocks (sharing with newly added H6 versions)
- Fix CEC clock (add 2nd enable bit, also fix predivider flag)
- Rename PMU_UNK1 register in USB PHY
- Add USB and MUSB DT binding patches
- Add MMC/SD speed modes to .dtsi

Changelog v1 .. v2:
- pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
- use differing h_i2s0 pin output names
- r-ccu: fix number of used clocks
- ccu: remove PLL-PERIPHy(4X)
- ccu: fix gpu1 divider range
- ccu: fix usb-phy3 parent
- ccu: add missing TV clocks
- ccu: rework to CLK_OF_DECLARE style
- ccu: enable output bit for PLL clocks
- ccu: renumber clocks
- .dtsi: drop sun50i-a64-system-control fallback
- .dtsi: drop unknown SRAM regions
- .dtsi: add more (undocumented) GPIO interrupts
- .dtsi: fix I2C3 pin names
- .dtsi: use a100-emmc fallback for MMC2
- .dtsi: add second EMAC controller
- .dtsi: use H3 MUSB controller fallback
- .dtsi: fix frame size for USB PHY PMU registers
- .dtsi: add USB0 PHY references
- .dtsi: fix IR controller clock source
- .dts: fix LED naming and swap pins
- .dts: use 5V supply parent for USB supply
- .dts: drop dummy IRQ for AXP
- .dts: enable 3V3 header pin power rail
- .dts: add SPI flash node
- .dts: make USB-C port peripheral only
- add IRQ-less AXP support
- add two patches to support more than one EMAC clock
- add patch to rework and extend USB PHY support
- add DT binding documentation patches

Andre Przywara (20):
dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616
clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
clk: sunxi-ng: Add support for the Allwinner H616 CCU
dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)
Input: axp20x-pek: Bail out if AXP has no interrupt line connected
mfd: axp20x: Allow AXP chips without interrupt lines
dt-bindings: sram: sunxi-sram: Add H616 compatible string
soc: sunxi: sram: Add support for more than one EMAC clock
dt-bindings: watchdog: sun4i: Add H616 compatible string
dt-bindings: i2c: mv64xxx: Add H616 compatible string
dt-bindings: media: IR: Add H616 IR compatible string
dt-bindings: rtc: sun6i: Add H616 compatible string
dt-bindings: spi: sunxi: Add H616 compatible string
dt-bindings: bus: rsb: Add H616 compatible string
dt-bindings: net: sun8i-emac: Add H616 compatible string
net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
phy: sun4i-usb: Rework HCI PHY (aka. "pmu_unk1") handling
arm64: dts: allwinner: Add Allwinner H616 .dtsi file
dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
arm64: dts: allwinner: Add OrangePi Zero 2 .dts

 .../devicetree/bindings/arm/sunxi.yaml        |    5 +
 .../bindings/bus/allwinner,sun8i-a23-rsb.yaml |    4 +-
 .../clock/allwinner,sun4i-a10-ccu.yaml        |    4 +
 .../bindings/i2c/marvell,mv64xxx-i2c.yaml     |   21 +-
 .../media/allwinner,sun4i-a10-ir.yaml         |   16 +-
 .../devicetree/bindings/mfd/axp20x.txt        |    3 +-
 .../net/allwinner,sun8i-a83t-emac.yaml        |    4 +-
 .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml |    3 +
 .../bindings/spi/allwinner,sun6i-a31-spi.yaml |    1 +
 .../allwinner,sun4i-a10-system-control.yaml   |    1 +
 .../watchdog/allwinner,sun4i-a10-wdt.yaml     |   12 +-
 arch/arm64/boot/dts/allwinner/Makefile        |    1 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  |  203 +++
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi |  573 ++++++++
 drivers/clk/sunxi-ng/Kconfig                  |    7 +-
 drivers/clk/sunxi-ng/Makefile                 |    1 +
 drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c        |   48 +
 drivers/clk/sunxi-ng/ccu-sun50i-h616.c        | 1150 +++++++++++++++++
 drivers/clk/sunxi-ng/ccu-sun50i-h616.h        |   56 +
 drivers/input/misc/axp20x-pek.c               |    4 +
 drivers/mfd/axp20x.c                          |   17 +-
 .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c |   12 +-
 drivers/phy/allwinner/phy-sun4i-usb.c         |   29 +-
 drivers/soc/sunxi/sunxi_sram.c                |   31 +-
 include/dt-bindings/clock/sun50i-h616-ccu.h   |  115 ++
 include/dt-bindings/reset/sun50i-h616-ccu.h   |   70 +
 26 files changed, 2323 insertions(+), 68 deletions(-)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
 create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
 create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
Signature · 1 line
2.17.5
#1 lore raw

PATCH v5 1/20 dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616

---
 .../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml    | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml +4 -0
index 3b45344ed758..a27025cd3909 100644
@@ -41,6 +41,8 @@ properties:
       - allwinner,sun50i-h5-ccu
       - allwinner,sun50i-h6-ccu
       - allwinner,sun50i-h6-r-ccu
+      - allwinner,sun50i-h616-ccu
+      - allwinner,sun50i-h616-r-ccu
       - allwinner,suniv-f1c100s-ccu
       - nextthing,gr8-ccu
 
@@ -82,6 +84,7 @@ if:
         - allwinner,sun50i-a64-r-ccu
         - allwinner,sun50i-a100-r-ccu
         - allwinner,sun50i-h6-r-ccu
+        - allwinner,sun50i-h616-r-ccu
 
 then:
   properties:
@@ -100,6 +103,7 @@ else:
         enum:
           - allwinner,sun50i-a100-ccu
           - allwinner,sun50i-h6-ccu
+          - allwinner,sun50i-h616-ccu
 
   then:
     properties:
Signature · 1 line
2.17.5
#2 lore raw

PATCH v5 2/20 clk: sunxi-ng: Add support for the Allwinner H616 R-CCU

In reply to Andre Przywara

The clocks itself are identical to the H6 R-CCU, it's just that the H616 has not all of them implemented (or connected).

---
 drivers/clk/sunxi-ng/Kconfig           |  2 +-
 drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 48 ++++++++++++++++++++++++++
 2 files changed, 49 insertions(+), 1 deletion(-)
drivers/clk/sunxi-ng/Kconfig +1 -1
index ce5f5847d5d3..feeb8d2074ee 100644
@@ -33,7 +33,7 @@ config SUN50I_H6_CCU
 	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
 
 config SUN50I_H6_R_CCU
-	bool "Support for the Allwinner H6 PRCM CCU"
+	bool "Support for the Allwinner H6 and H616 PRCM CCU"
 	default ARM64 && ARCH_SUNXI
 	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
 
drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c +48 -0

75 lines not on this page · raw message

Signature · 1 line
2.17.5
#3 lore raw

PATCH v5 3/20 clk: sunxi-ng: Add support for the Allwinner H616 CCU

In reply to Andre Przywara

While the clocks are fairly similar to the H6, many differ in tiny details, so a separate clock driver seems indicated.

Derived from the H6 clock driver, and adjusted according to the manual.

---
 drivers/clk/sunxi-ng/Kconfig                |    5 +
 drivers/clk/sunxi-ng/Makefile               |    1 +
 drivers/clk/sunxi-ng/ccu-sun50i-h616.c      | 1150 +++++++++++++++++++
 drivers/clk/sunxi-ng/ccu-sun50i-h616.h      |   56 +
 include/dt-bindings/clock/sun50i-h616-ccu.h |  115 ++
 include/dt-bindings/reset/sun50i-h616-ccu.h |   70 ++
 6 files changed, 1397 insertions(+)
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
 create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
 create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
drivers/clk/sunxi-ng/Kconfig +5 -0
index feeb8d2074ee..cd46d8853876 100644
@@ -32,6 +32,11 @@ config SUN50I_H6_CCU
 	default ARM64 && ARCH_SUNXI
 	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
 
+config SUN50I_H616_CCU
+	bool "Support for the Allwinner H616 CCU"
+	default ARM64 && ARCH_SUNXI
+	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
 config SUN50I_H6_R_CCU
 	bool "Support for the Allwinner H6 and H616 PRCM CCU"
 	default ARM64 && ARCH_SUNXI
drivers/clk/sunxi-ng/Makefile +1 -0
index 3eb5cff40eac..96c324306d97 100644
@@ -26,6 +26,7 @@ obj-$(CONFIG_SUN50I_A64_CCU)	+= ccu-sun50i-a64.o
 obj-$(CONFIG_SUN50I_A100_CCU)	+= ccu-sun50i-a100.o
 obj-$(CONFIG_SUN50I_A100_R_CCU)	+= ccu-sun50i-a100-r.o
 obj-$(CONFIG_SUN50I_H6_CCU)	+= ccu-sun50i-h6.o
+obj-$(CONFIG_SUN50I_H616_CCU)	+= ccu-sun50i-h616.o
 obj-$(CONFIG_SUN50I_H6_R_CCU)	+= ccu-sun50i-h6-r.o
 obj-$(CONFIG_SUN4I_A10_CCU)	+= ccu-sun4i-a10.o
 obj-$(CONFIG_SUN5I_CCU)		+= ccu-sun5i.o
drivers/clk/sunxi-ng/ccu-sun50i-h616.c new file +1150 -0

1,150 lines not on this page · raw message

drivers/clk/sunxi-ng/ccu-sun50i-h616.h new file +56 -0

56 lines not on this page · raw message

include/dt-bindings/clock/sun50i-h616-ccu.h new file +115 -0

115 lines not on this page · raw message

include/dt-bindings/reset/sun50i-h616-ccu.h new file +70 -0

70 lines not on this page · raw message

Signature · 1 line
2.17.5
#4 lore raw

PATCH v5 4/20 dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

In reply to Andre Przywara

The AXP305 PMIC used in AXP805 seems to be fully compatible to the AXP805 PMIC, so add the proper chain of compatible strings.

Also at least on one board (Orangepi Zero2) there is no interrupt line connected to the CPU, so make the "interrupts" property optional.

---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/mfd/axp20x.txt +2 -1
index 4991a6415796..4fd748101e3c 100644
@@ -26,10 +26,10 @@ Required properties:
     * "x-powers,axp803"
     * "x-powers,axp806"
     * "x-powers,axp805", "x-powers,axp806"
+    * "x-powers,axp803", "x-powers,axp805", "x-powers,axp806"
     * "x-powers,axp809"
     * "x-powers,axp813"
 - reg: The I2C slave address or RSB hardware address for the AXP chip
-- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
@@ -43,6 +43,7 @@ more information:
 			AXP20x/LDO3: software-based implementation
 
 Optional properties:
+- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
 		      AXP22X/8XX: range: 1800-4050, Default: 3   MHz
Signature · 1 line
2.17.5
Acked-by on v5 4/20
#5 lore raw

Re: [PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

Quoted 7 lines · Andre Przywara

The AXP305 PMIC used in AXP805 seems to be fully compatible to the AXP805 PMIC, so add the proper chain of compatible strings.

Also at least on one board (Orangepi Zero2) there is no interrupt line connected to the CPU, so make the "interrupts" property optional.

Maxime

#6 lore raw

Re: [linux-sunxi] [PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

In reply to Andre Przywara

Hi,

Quoted 2 lines · Andre Przywara

The AXP305 PMIC used in AXP805 seems to be fully compatible to the

                          ^

This statement doesn't quite make sense. I assume you wanted to mention a board or the H616 SoC here?

Quoted 15 lines

AXP805 PMIC, so add the proper chain of compatible strings.

Also at least on one board (Orangepi Zero2) there is no interrupt line connected to the CPU, so make the "interrupts" property optional.

---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/mfd/axp20x.txt +0 -0
index 4991a6415796..4fd748101e3c 100644

Documentation/devicetree/bindings/mfd/axp20x.txt Required properties: · line 29

Quoted 4 lines
Documentation/devicetree/bindings/mfd/axp20x.txt +1 -0
@@ -26,10 +26,10 @@ Required properties:
     * "x-powers,axp803"
     * "x-powers,axp806"
     * "x-powers,axp805", "x-powers,axp806"
+    * "x-powers,axp803", "x-powers,axp805", "x-powers,axp806"

axp305? axp803 is used with A64 IIRC.

ChenYu

Quoted 22 lines
Documentation/devicetree/bindings/mfd/axp20x.txt +1 -2
     * "x-powers,axp809"
     * "x-powers,axp813"
 - reg: The I2C slave address or RSB hardware address for the AXP chip
-- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
@@ -43,6 +43,7 @@ more information:
                        AXP20x/LDO3: software-based implementation
 
 Optional properties:
+- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
                      AXP152/20X: range:  750-1875, Default: 1.5 MHz
                      AXP22X/8XX: range: 1800-4050, Default: 3   MHz
--

2.17.5

--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20210127172500.13356-5-andre.przywara%40arm.com.

#7 lore raw

Re: [linux-sunxi] [PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

On Tue, 2 Feb 2021 15:55:50 +0800
Chen-Yu Tsai <[email protected]> wrote:

Hi,

Quoted 6 lines · Andre Przywara
Quoted 2 lines

The AXP305 PMIC used in AXP805 seems to be fully compatible to the

                          ^

This statement doesn't quite make sense. I assume you wanted to mention a board or the H616 SoC here?

Argh, indeed!

Quoted 10 lines
Quoted 10 lines

AXP805 PMIC, so add the proper chain of compatible strings.

Also at least on one board (Orangepi Zero2) there is no interrupt line connected to the CPU, so make the "interrupts" property optional.

---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
Quoted 11 lines

Documentation/devicetree/bindings/mfd/axp20x.txt Required properties: · line 29

Quoted 9 lines
Documentation/devicetree/bindings/mfd/axp20x.txt +1 -0
index 4991a6415796..4fd748101e3c 100644
@@ -26,10 +26,10 @@ Required properties:
     * "x-powers,axp803"
     * "x-powers,axp806"
     * "x-powers,axp805", "x-powers,axp806"
+    * "x-powers,axp803", "x-powers,axp805", "x-powers,axp806"  

axp305? axp803 is used with A64 IIRC.

Oh, well spotted. This AXP naming already confused me when they were all called 80x, now using 30x gave me the rest ;-)

Sorry for the blunder!

Cheers,
Andre

Quoted 25 lines

ChenYu

Quoted 22 lines
Documentation/devicetree/bindings/mfd/axp20x.txt +1 -2
     * "x-powers,axp809"
     * "x-powers,axp813"
 - reg: The I2C slave address or RSB hardware address for the AXP chip
-- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
@@ -43,6 +43,7 @@ more information:
                        AXP20x/LDO3: software-based implementation
 
 Optional properties:
+- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
                      AXP152/20X: range:  750-1875, Default: 1.5 MHz
                      AXP22X/8XX: range: 1800-4050, Default: 3   MHz
--

2.17.5

--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20210127172500.13356-5-andre.przywara%40arm.com.

maintainer Acked-by on v5 4/20
#8 lore raw

Re: [PATCH v5 04/20] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

In reply to Andre Przywara
Quoted 16 lines · Andre Przywara

The AXP305 PMIC used in AXP805 seems to be fully compatible to the AXP805 PMIC, so add the proper chain of compatible strings.

Also at least on one board (Orangepi Zero2) there is no interrupt line connected to the CPU, so make the "interrupts" property optional.

---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/mfd/axp20x.txt +0 -0
index 4991a6415796..4fd748101e3c 100644

Documentation/devicetree/bindings/mfd/axp20x.txt Required properties: · line 29

Quoted 4 lines
Documentation/devicetree/bindings/mfd/axp20x.txt +1 -0
@@ -26,10 +26,10 @@ Required properties:
     * "x-powers,axp803"
     * "x-powers,axp806"
     * "x-powers,axp805", "x-powers,axp806"
+    * "x-powers,axp803", "x-powers,axp805", "x-powers,axp806"

I don't normally (yet) ask for schema conversions on compatible additions, but this is one of the few remaining compatibles with no schema for allwinner. So a conversion here would be nice. BTW, dtschema now has a better check for this (-m option) without the false positives. I plan to turn on the option soon (doesn't matter for dtbs as they all have lots of warnings, but bindings also get warnings).

Either way,

Quoted 18 lines
Documentation/devicetree/bindings/mfd/axp20x.txt +1 -1
     * "x-powers,axp809"
     * "x-powers,axp813"
 - reg: The I2C slave address or RSB hardware address for the AXP chip
-- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
@@ -43,6 +43,7 @@ more information:
 			AXP20x/LDO3: software-based implementation
 
 Optional properties:
+- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
 		      AXP22X/8XX: range: 1800-4050, Default: 3   MHz
Signature · 1 line
2.17.5

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#9 lore raw

PATCH v5 5/20 Input: axp20x-pek: Bail out if AXP has no interrupt line connected

In reply to Andre Przywara

On at least one board (Orangepi Zero2) the AXP305 PMIC does not have its interrupt line connected to the CPU (mostly because the H616 SoC does not feature an NMI pin anymore).
After allowing the AXP driver to proceed without an "interrupts" property [1], the axp20x-pek driver crashes with a NULL pointer dereference (see below).

Check for the regmap_irqc member to be not NULL before proceeding with probe. This gets normally filled by the call to regmap_add_irq_chip(), which we allow to skip now, when the DT node lacks an interrupt property.

....

[    3.843388] sunxi-rsb 7083000.rsb: RSB running at 3000000 Hz
[    3.849972] axp20x-rsb sunxi-rsb-745: AXP20x variant AXP806 found
[    3.857971] Unable to handle kernel NULL pointer dereference at
virtual address 00000000000001b8
[    3.866855] Mem abort info:
[    3.869691]   ESR = 0x96000004
[    3.872749]   EC = 0x25: DABT (current EL), IL = 32 bits
[    3.878092]   SET = 0, FnV = 0
[    3.881149]   EA = 0, S1PTW = 0
[    3.884309] Data abort info:
[    3.887210]   ISV = 0, ISS = 0x00000004
[    3.891062]   CM = 0, WnR = 0
[    3.894049] [00000000000001b8] user address but active_mm is swapper
[    3.900590] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[    3.906166] Modules linked in:
[    3.909227] CPU: 2 PID: 34 Comm: kworker/2:1 Not tainted 5.11.0-rc1
[    3.915925] Hardware name: OrangePi Zero2 (DT)
[    3.920367] Workqueue: events deferred_probe_work_func
[    3.925518] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--)
[    3.931522] pc : regmap_irq_get_virq+0x0/0x48
[    3.935883] lr : axp20x_pek_probe+0x78/0x200
[    3.940147] sp : ffff800012fdb450
[    3.943459] x29: ffff800012fdb450 x28: ffff0000054af340
[    3.948776] x27: ffff000005534000 x26: ffff000005534810
[    3.954091] x25: ffff800012883028 x24: 0000000000000002
[    3.959407] x23: ffff80001157eaf0 x22: ffff000005534810
[    3.964722] x21: ffff000005534800 x20: ffff0000054b0580
[    3.970037] x19: 000000000000000b x18: 0000000000000000
[    3.975353] x17: 0000000000000001 x16: 0000000000000019
[    3.980668] x15: 000002ce4ea04ae6 x14: 000000000000014f
[    3.985983] x13: 0000000000000282 x12: 0000000000000030
[    3.991298] x11: 0000000000000038 x10: 0101010101010101
[    3.996613] x9 : 0000000000000000 x8 : 7f7f7f7f7f7f7f7f
[    4.001928] x7 : ff5141435e4a444f x6 : 0000000000000080
[    4.007243] x5 : 0000000000000000 x4 : 8000000000000000
[    4.012558] x3 : 0000000000000000 x2 : 0000000000000000
[    4.017872] x1 : 000000000000000b x0 : 0000000000000000
[    4.023188] Call trace:
[    4.025635]  regmap_irq_get_virq+0x0/0x48
[    4.029646]  platform_probe+0x68/0xd8
[    4.033312]  really_probe+0xe4/0x3b0
[    4.036889]  driver_probe_device+0x58/0xb8
[    4.040986]  __device_attach_driver+0x84/0xc8
[    4.045342]  bus_for_each_drv+0x78/0xc8
[    4.049178]  __device_attach+0xf0/0x150
[    4.053013]  device_initial_probe+0x14/0x20
[    4.057196]  bus_probe_device+0x9c/0xa8
[    4.061032]  device_add+0x36c/0x7b8
[    4.064525]  platform_device_add+0x100/0x238
[    4.068796]  mfd_add_devices+0x494/0x718
[    4.072721]  axp20x_device_probe+0x70/0x158
[    4.076904]  axp20x_rsb_probe+0x94/0xd0
[    4.080741]  sunxi_rsb_device_probe+0x6c/0x88
[    4.085102]  really_probe+0xe4/0x3b0
[    4.088679]  driver_probe_device+0x58/0xb8
[    4.092776]  __device_attach_driver+0x84/0xc8
[    4.097132]  bus_for_each_drv+0x78/0xc8
[    4.100967]  __device_attach+0xf0/0x150
[    4.104803]  device_initial_probe+0x14/0x20
[    4.108986]  bus_probe_device+0x9c/0xa8
[    4.112821]  device_add+0x36c/0x7b8
[    4.116313]  device_register+0x20/0x30
[    4.120065]  sunxi_rsb_probe+0x4e4/0x608

....

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/633392.html

---
 drivers/input/misc/axp20x-pek.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/input/misc/axp20x-pek.c +4 -0
index 9c6386b2af33..abe52ef194ee 100644
@@ -309,6 +309,10 @@ static int axp20x_pek_probe(struct platform_device *pdev)
 
 	axp20x_pek->axp20x = dev_get_drvdata(pdev->dev.parent);
 
+	/* In case there is no interrupt line from the AXP towards the CPU. */
+	if (!axp20x_pek->axp20x->regmap_irqc)
+		return -ENODEV;
+
 	axp20x_pek->irq_dbr = platform_get_irq_byname(pdev, "PEK_DBR");
 	if (axp20x_pek->irq_dbr < 0)
 		return axp20x_pek->irq_dbr;
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
maintainer
#10 lore raw

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

Hi Andre,

Quoted 11 lines · Andre Przywara

On at least one board (Orangepi Zero2) the AXP305 PMIC does not have its interrupt line connected to the CPU (mostly because the H616 SoC does not feature an NMI pin anymore).
After allowing the AXP driver to proceed without an "interrupts" property [1], the axp20x-pek driver crashes with a NULL pointer dereference (see below).

Check for the regmap_irqc member to be not NULL before proceeding with probe. This gets normally filled by the call to regmap_add_irq_chip(), which we allow to skip now, when the DT node lacks an interrupt property.

No, the driver is not the right place to patch this; regmap should be fixed so it does not crash instead.

Thanks.

Signature · 6 lines
Dmitry

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#11 lore raw

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

On Wed, 27 Jan 2021 11:42:15 -0800
Dmitry Torokhov <[email protected]> wrote:

Hi Dmitry,

thanks for your feedback!

Quoted 8 lines · Andre Przywara
Quoted 7 lines

On at least one board (Orangepi Zero2) the AXP305 PMIC does not have its interrupt line connected to the CPU (mostly because the H616 SoC does not feature an NMI pin anymore).
After allowing the AXP driver to proceed without an "interrupts" property [1], the axp20x-pek driver crashes with a NULL pointer dereference (see below).

Quoted 7 lines
Quoted 4 lines

Check for the regmap_irqc member to be not NULL before proceeding with probe. This gets normally filled by the call to regmap_add_irq_chip(), which we allow to skip now, when the DT node lacks an interrupt property.

No, the driver is not the right place to patch this; regmap should be fixed so it does not crash instead.

I am not sure this is the right approach, those regmap functions look more like an internal interface to me, with lots of wrapper functions happily dereferencing pointers and reaching into structs. Moving NULL checks into those does not sound like the right thing. CC:ing Mark for more opinions on this.

A more general solution would be to not instantiate this driver here at all, when we don't have an interrupt line.
However at the moment the AXP MFD driver uses a const struct to hold all MFD cells, so there is no easy way of omitting the power key device dynamically. And even then it would hard code the requirement for an interrupt into the MFD driver, when this could be considered an implementation detail of the axp20x-pek driver.

That's why I came up with this patch here, which was the easiest and
cleanest: This driver *requires* a valid regmap_irqc, so it should verify this at probe time, kind of like a normal driver would bail out if no IRQ line could be reserved.

Let me know what you think!

Cheers,
Andre

maintainer
#12 lore raw

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

Quoted 7 lines · Andre Przywara
Quoted 6 lines · Dmitry Torokhov
Quoted 4 lines · Andre Przywara

Check for the regmap_irqc member to be not NULL before proceeding with probe. This gets normally filled by the call to regmap_add_irq_chip(), which we allow to skip now, when the DT node lacks an interrupt property.

It sounds like you're trying to register an IRQ chip with a somehow bogus configuration?

Quoted 8 lines
Quoted 2 lines

No, the driver is not the right place to patch this; regmap should be fixed so it does not crash instead.

I am not sure this is the right approach, those regmap functions look more like an internal interface to me, with lots of wrapper functions happily dereferencing pointers and reaching into structs. Moving NULL checks into those does not sound like the right thing. CC:ing Mark for more opinions on this.

Without having seen the actual issue if you're trying to register an interrupt controller with a known broken hardware configuration that does seem like something the caller just shouldn't be doing, it's not something that's going to transiently happen at runtime and we're very much trusting that the caller got things right.

Quoted 7 lines

A more general solution would be to not instantiate this driver here at all, when we don't have an interrupt line.
However at the moment the AXP MFD driver uses a const struct to hold all MFD cells, so there is no easy way of omitting the power key device dynamically. And even then it would hard code the requirement for an interrupt into the MFD driver, when this could be considered an implementation detail of the axp20x-pek driver.

Another approach is to just register the optional device separately.

#13 lore raw

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

Quoted 11 lines · On Thu, 28 Jan 2021 11:36:01 +0000 Mark Brown <[email protected]> wrote:
Quoted 7 lines · Andre Przywara
Quoted 6 lines · Dmitry Torokhov
Quoted 4 lines · Andre Przywara

Check for the regmap_irqc member to be not NULL before proceeding with probe. This gets normally filled by the call to regmap_add_irq_chip(), which we allow to skip now, when the DT node lacks an interrupt property.

It sounds like you're trying to register an IRQ chip with a somehow bogus configuration?

Quick background: Those AXP PMICs have an IRQ pin, that was always connected to the NMI pin on Allwinner SoCs. This was used for the power button GPIO interrupt. Now the H616 does not have this pin anymore, and the board does not use a GPIO either.
I patched the AXP MFD driver [1] to skip the regmap-irq creation when no interrupts DT property was found, but this NULL pointer now understandably confuses the -pek driver, and leads to this crash:

http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/634969.html

Hence I wanted to plug this hole, which seems useful regardless of this particular issue.

[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/634971.html

Quoted 23 lines
Quoted 8 lines
Quoted 2 lines

No, the driver is not the right place to patch this; regmap should be fixed so it does not crash instead.

I am not sure this is the right approach, those regmap functions look more like an internal interface to me, with lots of wrapper functions happily dereferencing pointers and reaching into structs. Moving NULL checks into those does not sound like the right thing. CC:ing Mark for more opinions on this.

Without having seen the actual issue if you're trying to register an interrupt controller with a known broken hardware configuration that does seem like something the caller just shouldn't be doing, it's not something that's going to transiently happen at runtime and we're very much trusting that the caller got things right.

Quoted 7 lines

A more general solution would be to not instantiate this driver here at all, when we don't have an interrupt line.
However at the moment the AXP MFD driver uses a const struct to hold all MFD cells, so there is no easy way of omitting the power key device dynamically. And even then it would hard code the requirement for an interrupt into the MFD driver, when this could be considered an implementation detail of the axp20x-pek driver.

Quoted 1 line

Another approach is to just register the optional device separately.

I will have a look at how much this takes.

Thanks,
Andre

maintainer
#14 lore raw

Re: [PATCH v5 05/20] Input: axp20x-pek: Bail out if AXP has no interrupt line connected

Quoted 5 lines · Andre Przywara
Quoted 2 lines · Mark Brown

It sounds like you're trying to register an IRQ chip with a somehow bogus configuration?

Quoted 8 lines

I patched the AXP MFD driver [1] to skip the regmap-irq creation when no interrupts DT property was found, but this NULL pointer now understandably confuses the -pek driver, and leads to this crash:

http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/634969.html

Hence I wanted to plug this hole, which seems useful regardless of this particular issue.

The driver code here looks pretty confused. It appears to be looking up the interrupt to use from a resource (which is what I'd expect for a MFD child) then for reasons I can't fathom trying to pass that resource into regmap_irq_get_virq() which is at best going to just return the value that was passed in but may potentially end up just returning a random interrupt other than the one that was asked for since we're passing in a global interrupt number rather than a controller relative one. I really can't tell what's supposed to be going on there. A driver should either use resources or it should use regmap_irq_get_virq(), using both is a bug.

The MFD for this device is also just plain buggy in that it is providing IRQ resources to the children when there is in fact no support for the interrupts on the device in the system. This means that the MFD core sees that it has no interrupt domain, assumes that those interrupt resources are in fact absolute interrupt numbers and passes them straight through to the children. This means that the children will just be requesting random interrupts in the system which may actually exist and be requestable which probably isn't going to end well. When there is no interrupt controller the parent should not be trying to supply interrupt resources to the children at all.

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#15 lore raw

PATCH v5 6/20 mfd: axp20x: Allow AXP chips without interrupt lines

In reply to Andre Przywara

Currently the AXP chip requires to have its IRQ line connected to some interrupt controller, and will fail probing when this is not the case.

On a new Allwinner SoC (H616) there is no NMI pin anymore, and at least one board does not connect the AXP's IRQ pin to anything else, so the interrupt functionality of the AXP chip is simply not available.

Check whether the interrupt line number returned by the platform code is valid, before trying to register the irqchip. If not, we skip this registration, to avoid the driver to bail out completely.

---
 drivers/mfd/axp20x.c | 17 +++++++++++------
 1 file changed, 11 insertions(+), 6 deletions(-)
drivers/mfd/axp20x.c +11 -6
index 3eae04e24ac8..00c163a1e20d 100644
@@ -959,12 +959,17 @@ int axp20x_device_probe(struct axp20x_dev *axp20x)
 				     AXP806_REG_ADDR_EXT_ADDR_SLAVE_MODE);
 	}
 
-	ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
-			  IRQF_ONESHOT | IRQF_SHARED | axp20x->irq_flags,
-			   -1, axp20x->regmap_irq_chip, &axp20x->regmap_irqc);
-	if (ret) {
-		dev_err(axp20x->dev, "failed to add irq chip: %d\n", ret);
-		return ret;
+	/* Only if there is an interrupt line connected towards the CPU. */
+	if (axp20x->irq > 0) {
+		ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
+				IRQF_ONESHOT | IRQF_SHARED | axp20x->irq_flags,
+				-1, axp20x->regmap_irq_chip,
+				&axp20x->regmap_irqc);
+		if (ret) {
+			dev_err(axp20x->dev, "failed to add irq chip: %d\n",
+				ret);
+			return ret;
+		}
 	}
 
 	ret = mfd_add_devices(axp20x->dev, -1, axp20x->cells,
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Acked-by on v5 6/20
#16 lore raw

Re: [PATCH v5 06/20] mfd: axp20x: Allow AXP chips without interrupt lines

Quoted 7 lines · Andre Przywara

Currently the AXP chip requires to have its IRQ line connected to some interrupt controller, and will fail probing when this is not the case.

On a new Allwinner SoC (H616) there is no NMI pin anymore, and at least one board does not connect the AXP's IRQ pin to anything else, so the interrupt functionality of the AXP chip is simply not available.

Quoted 5 lines

Check whether the interrupt line number returned by the platform code is valid, before trying to register the irqchip. If not, we skip this registration, to avoid the driver to bail out completely.

Maxime

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Acked-by
#17 lore raw

Re: [linux-sunxi] Re: [PATCH v5 06/20] mfd: axp20x: Allow AXP chips without interrupt lines

Quoted 9 lines · Maxime Ripard
Quoted 7 lines · Andre Przywara

Currently the AXP chip requires to have its IRQ line connected to some interrupt controller, and will fail probing when this is not the case.

On a new Allwinner SoC (H616) there is no NMI pin anymore, and at least one board does not connect the AXP's IRQ pin to anything else, so the interrupt functionality of the AXP chip is simply not available.

Quoted 7 lines
Quoted 5 lines

Check whether the interrupt line number returned by the platform code is valid, before trying to register the irqchip. If not, we skip this registration, to avoid the driver to bail out completely.

#18 lore raw

Re: [PATCH v5 06/20] mfd: axp20x: Allow AXP chips without interrupt lines

In reply to Andre Przywara
Quoted 7 lines · Andre Przywara

Currently the AXP chip requires to have its IRQ line connected to some interrupt controller, and will fail probing when this is not the case.

On a new Allwinner SoC (H616) there is no NMI pin anymore, and at least one board does not connect the AXP's IRQ pin to anything else, so the interrupt functionality of the AXP chip is simply not available.

Quoted 8 lines

Check whether the interrupt line number returned by the platform code is valid, before trying to register the irqchip. If not, we skip this registration, to avoid the driver to bail out completely.

---
 drivers/mfd/axp20x.c | 17 +++++++++++------
 1 file changed, 11 insertions(+), 6 deletions(-)

For my own reference (apply this as-is to your sign-off block):

Signature · 4 lines
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
#19 lore raw

PATCH v5 7/20 dt-bindings: sram: sunxi-sram: Add H616 compatible string

In reply to Andre Przywara

The H616 adds a second EMAC clock register. We don't know about the exact SRAM properties yet, so this gets omitted for now.

---
 .../bindings/sram/allwinner,sun4i-a10-system-control.yaml        | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml +1 -0
index b66a07e21d1e..1c426c211e36 100644
@@ -49,6 +49,7 @@ properties:
       - items:
           - const: allwinner,suniv-f1c100s-system-control
           - const: allwinner,sun4i-a10-system-control
+      - const: allwinner,sun50i-h616-system-control
 
   reg:
     maxItems: 1
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#20 lore raw

PATCH v5 8/20 soc: sunxi: sram: Add support for more than one EMAC clock

In reply to Andre Przywara

The Allwinner H616 adds a second EMAC clock register at offset 0x34, for controlling the second EMAC in this chip.

Allow to extend the regmap in this case, to cover more than the current 4 bytes exported.

---
 drivers/soc/sunxi/sunxi_sram.c | 31 +++++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 8 deletions(-)
drivers/soc/sunxi/sunxi_sram.c +23 -8
index d4c7bd59429e..42833e33a96c 100644
@@ -283,7 +283,7 @@ int sunxi_sram_release(struct device *dev)
 EXPORT_SYMBOL(sunxi_sram_release);
 
 struct sunxi_sramc_variant {
-	bool has_emac_clock;
+	int num_emac_clocks;
 };
 
 static const struct sunxi_sramc_variant sun4i_a10_sramc_variant = {
@@ -291,20 +291,31 @@ static const struct sunxi_sramc_variant sun4i_a10_sramc_variant = {
 };
 
 static const struct sunxi_sramc_variant sun8i_h3_sramc_variant = {
-	.has_emac_clock = true,
+	.num_emac_clocks = 1,
 };
 
 static const struct sunxi_sramc_variant sun50i_a64_sramc_variant = {
-	.has_emac_clock = true,
+	.num_emac_clocks = 1,
+};
+
+static const struct sunxi_sramc_variant sun50i_h616_sramc_variant = {
+	.num_emac_clocks = 2,
 };
 
 #define SUNXI_SRAM_EMAC_CLOCK_REG	0x30
 static bool sunxi_sram_regmap_accessible_reg(struct device *dev,
 					     unsigned int reg)
 {
-	if (reg == SUNXI_SRAM_EMAC_CLOCK_REG)
-		return true;
-	return false;
+	const struct sunxi_sramc_variant *variant;
+
+	variant = of_device_get_match_data(dev);
+
+	if (reg < SUNXI_SRAM_EMAC_CLOCK_REG)
+		return false;
+	if (reg > SUNXI_SRAM_EMAC_CLOCK_REG + variant->num_emac_clocks * 4)
+		return false;
+
+	return true;
 }
 
 static struct regmap_config sunxi_sram_emac_clock_regmap = {
@@ -312,7 +323,7 @@ static struct regmap_config sunxi_sram_emac_clock_regmap = {
 	.val_bits       = 32,
 	.reg_stride     = 4,
 	/* last defined register */
-	.max_register   = SUNXI_SRAM_EMAC_CLOCK_REG,
+	.max_register   = SUNXI_SRAM_EMAC_CLOCK_REG + 4,
 	/* other devices have no business accessing other registers */
 	.readable_reg	= sunxi_sram_regmap_accessible_reg,
 	.writeable_reg	= sunxi_sram_regmap_accessible_reg,
@@ -343,7 +354,7 @@ static int sunxi_sram_probe(struct platform_device *pdev)
 	if (!d)
 		return -ENOMEM;
 
-	if (variant->has_emac_clock) {
+	if (variant->num_emac_clocks > 0) {
 		emac_clock = devm_regmap_init_mmio(&pdev->dev, base,
 						   &sunxi_sram_emac_clock_regmap);
 
@@ -387,6 +398,10 @@ static const struct of_device_id sunxi_sram_dt_match[] = {
 		.compatible = "allwinner,sun50i-h5-system-control",
 		.data = &sun50i_a64_sramc_variant,
 	},
+	{
+		.compatible = "allwinner,sun50i-h616-system-control",
+		.data = &sun50i_h616_sramc_variant,
+	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, sunxi_sram_dt_match);
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#21 lore raw

PATCH v5 9/20 dt-bindings: watchdog: sun4i: Add H616 compatible string

In reply to Andre Przywara

Use enums to group all compatible devices together on the way.

---
 .../bindings/watchdog/allwinner,sun4i-a10-wdt.yaml   | 12 +++++-------
 1 file changed, 5 insertions(+), 7 deletions(-)
Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml +5 -7
index 5ac607de8be4..9aa3c313c49f 100644
@@ -19,13 +19,11 @@ properties:
       - const: allwinner,sun4i-a10-wdt
       - const: allwinner,sun6i-a31-wdt
       - items:
-          - const: allwinner,sun50i-a64-wdt
-          - const: allwinner,sun6i-a31-wdt
-      - items:
-          - const: allwinner,sun50i-a100-wdt
-          - const: allwinner,sun6i-a31-wdt
-      - items:
-          - const: allwinner,sun50i-h6-wdt
+          - enum:
+              - allwinner,sun50i-a64-wdt
+              - allwinner,sun50i-a100-wdt
+              - allwinner,sun50i-h6-wdt
+              - allwinner,sun50i-h616-wdt
           - const: allwinner,sun6i-a31-wdt
       - items:
           - const: allwinner,suniv-f1c100s-wdt
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#22 lore raw

PATCH v5 10/20 dt-bindings: i2c: mv64xxx: Add H616 compatible string

In reply to Andre Przywara

Add the obvious compatible name to the existing I2C binding, and pair it with the existing A31 fallback compatible string, as the devices are compatible.

On the way use enums to group all compatible devices together.

---
 .../bindings/i2c/marvell,mv64xxx-i2c.yaml     | 21 +++++++------------
 1 file changed, 7 insertions(+), 14 deletions(-)
Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml +7 -14
index 5b5ae402f97a..eb72dd571def 100644
@@ -18,21 +18,14 @@ properties:
           - const: allwinner,sun4i-a10-i2c
       - const: allwinner,sun6i-a31-i2c
       - items:
-          - const: allwinner,sun8i-a23-i2c
+          - enum:
+              - allwinner,sun8i-a23-i2c
+              - allwinner,sun8i-a83t-i2c
+              - allwinner,sun50i-a64-i2c
+              - allwinner,sun50i-a100-i2c
+              - allwinner,sun50i-h6-i2c
+              - allwinner,sun50i-h616-i2c
           - const: allwinner,sun6i-a31-i2c
-      - items:
-          - const: allwinner,sun8i-a83t-i2c
-          - const: allwinner,sun6i-a31-i2c
-      - items:
-          - const: allwinner,sun50i-a64-i2c
-          - const: allwinner,sun6i-a31-i2c
-      - items:
-          - const: allwinner,sun50i-a100-i2c
-          - const: allwinner,sun6i-a31-i2c
-      - items:
-          - const: allwinner,sun50i-h6-i2c
-          - const: allwinner,sun6i-a31-i2c
-
       - const: marvell,mv64xxx-i2c
       - const: marvell,mv78230-i2c
       - const: marvell,mv78230-a0-i2c
Signature · 1 line
2.17.5
Applied
#23 lore raw

Re: [PATCH v5 10/20] dt-bindings: i2c: mv64xxx: Add H616 compatible string

Quoted 9 lines · Andre Przywara

Add the obvious compatible name to the existing I2C binding, and pair it with the existing A31 fallback compatible string, as the devices are compatible.

On the way use enums to group all compatible devices together.

Applied to for-next, thanks!

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#24 lore raw

PATCH v5 11/20 dt-bindings: media: IR: Add H616 IR compatible string

In reply to Andre Przywara

Add the obvious compatible name to the existing IR binding, and pair it with the existing A31 fallback compatible string, as the devices are compatible.

On the way use enums to group all compatible devices together.

---
 .../bindings/media/allwinner,sun4i-a10-ir.yaml   | 16 ++++++----------
 1 file changed, 6 insertions(+), 10 deletions(-)
Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml +6 -10
index 5fa19d4aeaf3..6d8395d6bca0 100644
@@ -20,16 +20,12 @@ properties:
       - const: allwinner,sun5i-a13-ir
       - const: allwinner,sun6i-a31-ir
       - items:
-          - const: allwinner,sun8i-a83t-ir
-          - const: allwinner,sun6i-a31-ir
-      - items:
-          - const: allwinner,sun8i-r40-ir
-          - const: allwinner,sun6i-a31-ir
-      - items:
-          - const: allwinner,sun50i-a64-ir
-          - const: allwinner,sun6i-a31-ir
-      - items:
-          - const: allwinner,sun50i-h6-ir
+          - enum:
+              - allwinner,sun8i-a83t-ir
+              - allwinner,sun8i-r40-ir
+              - allwinner,sun50i-a64-ir
+              - allwinner,sun50i-h6-ir
+              - allwinner,sun50i-h616-ir
           - const: allwinner,sun6i-a31-ir
 
   reg:
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#25 lore raw

PATCH v5 12/20 dt-bindings: rtc: sun6i: Add H616 compatible string

In reply to Andre Przywara

Add the obvious compatible name to the existing RTC binding, and pair it with the existing H6 fallback compatible string, as the devices are compatible.

---
 .../devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml       | 3 +++
 1 file changed, 3 insertions(+)
Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml +3 -0
index b1b0ee769b71..4193e5813344 100644
@@ -26,6 +26,9 @@ properties:
           - const: allwinner,sun50i-a64-rtc
           - const: allwinner,sun8i-h3-rtc
       - const: allwinner,sun50i-h6-rtc
+      - items:
+          - const: allwinner,sun50i-h616-rtc
+          - const: allwinner,sun50i-h6-rtc
 
   reg:
     maxItems: 1
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#27 lore raw

Re: [PATCH v5 12/20] dt-bindings: rtc: sun6i: Add H616 compatible string

In reply to Andre Przywara

Hi!

Dne sreda, 27. januar 2021 ob 18:24:52 CET je Andre Przywara napisal(a):

Quoted 3 lines

Add the obvious compatible name to the existing RTC binding, and pair it with the existing H6 fallback compatible string, as the devices are compatible.

After close lookup I would disagree with this observation. Major difference is that H616 doesn't support usage of external 32768 Hz oscillator. It uses 24 MHz oscillator with divider for that case. Due to that change, whole logic for external oscillator should go out. Additionally, this logic overwrites default value in LOSC_CTRL register, which is not nice (there is no documentation for those bits).

Best regards,
Jernej

Review

Quoted 8 lines
---
 .../devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml       | 3 +++
 1 file changed, 3 insertions(+)
(quoted diff) +0 -0

rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml

Quoted 17 lines

index b1b0ee769b71..4193e5813344 100644

Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml +3 -0
@@ -26,6 +26,9 @@ properties:
           - const: allwinner,sun50i-a64-rtc
           - const: allwinner,sun8i-h3-rtc
       - const: allwinner,sun50i-h6-rtc
+      - items:
+          - const: allwinner,sun50i-h616-rtc
+          - const: allwinner,sun50i-h6-rtc
 
   reg:
     maxItems: 1
Signature · 1 line
2.17.5
#28 lore raw

Re: [PATCH v5 12/20] dt-bindings: rtc: sun6i: Add H616 compatible string

On Sun, 31 Jan 2021 14:44:40 +0100
Jernej Škrabec <[email protected]> wrote:

Hi Jernej,

Quoted 11 lines

Dne sreda, 27. januar 2021 ob 18:24:52 CET je Andre Przywara napisal(a):

Quoted 3 lines

Add the obvious compatible name to the existing RTC binding, and pair it with the existing H6 fallback compatible string, as the devices are compatible.

After close lookup I would disagree with this observation. Major difference is that H616 doesn't support usage of external 32768 Hz oscillator. It uses 24 MHz oscillator with divider for that case. Due to that change, whole logic for external oscillator should go out. Additionally, this logic overwrites default value in LOSC_CTRL register, which is not nice (there is no documentation for those bits).

Thanks for the heads up, and I wonder if there is more to that. From comparing the RTC documentation, I wonder if we should actually have incoming clocks in the bindings (the crystals / external clock sources with 32KHz, 16MHz, 24MHz). Then we could actually model which crystals the board provides. It seems like the H6 made the 32KHz OSC optional, and the H616 simply doesn't support it anymore - at the very least I don't see any X32K pins anymore.

But more importantly: looking more closely (I only skimmed over the register summary back then) the actual RTC registers are different:
the H616 encodes a linear day number (vs. a broken-down D-M-Y), also the time-of-day register is different.

So we definitely need a driver update, and hence need to drop this patch.

Cheers,
Andre

Quoted 31 lines

Best regards,
Jernej

Review

Quoted 8 lines
---
 .../devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml       | 3 +++
 1 file changed, 3 insertions(+)
(quoted diff) +0 -0

rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml

Quoted 17 lines

index b1b0ee769b71..4193e5813344 100644

Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml +3 -0
@@ -26,6 +26,9 @@ properties:
           - const: allwinner,sun50i-a64-rtc
           - const: allwinner,sun8i-h3-rtc
       - const: allwinner,sun50i-h6-rtc
+      - items:
+          - const: allwinner,sun50i-h616-rtc
+          - const: allwinner,sun50i-h6-rtc
 
   reg:
     maxItems: 1
Signature · 1 line
2.17.5
#29 lore raw

PATCH v5 13/20 dt-bindings: spi: sunxi: Add H616 compatible string

In reply to Andre Przywara

Add the obvious compatible name to the existing SPI binding, and pair it with the existing H3 fallback compatible string, as the devices are compatible.

---
 .../devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml         | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml +1 -0
index 7866a655d81c..908248260afa 100644
@@ -25,6 +25,7 @@ properties:
           - enum:
               - allwinner,sun8i-r40-spi
               - allwinner,sun50i-h6-spi
+              - allwinner,sun50i-h616-spi
           - const: allwinner,sun8i-h3-spi
 
   reg:
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#30 lore raw

PATCH v5 14/20 dt-bindings: bus: rsb: Add H616 compatible string

In reply to Andre Przywara

Add the obvious compatible name to the existing RSB binding, and pair it with the existing A23 fallback compatible string, as the devices are compatible.

---
 .../devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml      | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml +3 -1
index 32d33b983d66..3d719f468a5b 100644
@@ -21,7 +21,9 @@ properties:
     oneOf:
       - const: allwinner,sun8i-a23-rsb
       - items:
-          - const: allwinner,sun8i-a83t-rsb
+          - enum:
+              - allwinner,sun8i-a83t-rsb
+              - allwinner,sun50i-h616-rsb
           - const: allwinner,sun8i-a23-rsb
 
   reg:
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#32 lore raw

PATCH v5 15/20 dt-bindings: net: sun8i-emac: Add H616 compatible string

In reply to Andre Przywara

Add the obvious compatible name to the existing EMAC binding, and pair it with the existing A64 fallback compatible string, as the devices are compatible.

On the way use enums to group the compatible devices together.

---
 .../devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml    | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml +3 -1
index 7f2578d48e3f..0ccdab103f59 100644
@@ -19,7 +19,9 @@ properties:
       - const: allwinner,sun8i-v3s-emac
       - const: allwinner,sun50i-a64-emac
       - items:
-          - const: allwinner,sun50i-h6-emac
+          - enum:
+              - allwinner,sun50i-h6-emac
+              - allwinner,sun50i-h616-emac
           - const: allwinner,sun50i-a64-emac
 
   reg:
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Acked-by on v5 15/20
#33 lore raw

Re: [PATCH v5 15/20] dt-bindings: net: sun8i-emac: Add H616 compatible string

Quoted 7 lines · Andre Przywara

Add the obvious compatible name to the existing EMAC binding, and pair it with the existing A64 fallback compatible string, as the devices are compatible.

On the way use enums to group the compatible devices together.

Maxime

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

maintainer Acked-by on v5 15/20
#34 lore raw

Re: [PATCH v5 15/20] dt-bindings: net: sun8i-emac: Add H616 compatible string

In reply to Andre Przywara
Quoted 11 lines · Andre Przywara

Add the obvious compatible name to the existing EMAC binding, and pair it with the existing A64 fallback compatible string, as the devices are compatible.

On the way use enums to group the compatible devices together.

---
 .../devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml    | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#35 lore raw

PATCH v5 16/20 net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register

In reply to Andre Przywara

The Allwinner H616 SoC has two EMAC controllers, with the second one being tied to the internal PHY, but also using a separate EMAC clock register.

To tell the driver about which clock register to use, we add a parameter to our syscon phandle. The driver will use this value as an index into the regmap, so that we can address more than the first register, if needed.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +10 -2
index 58e0511badba..c7951790ed98 100644
@@ -1124,11 +1124,13 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
 	struct stmmac_resources stmmac_res;
 	struct sunxi_priv_data *gmac;
 	struct device *dev = &pdev->dev;
+	struct reg_field syscon_field;
 	phy_interface_t interface;
 	int ret;
 	struct stmmac_priv *priv;
 	struct net_device *ndev;
 	struct regmap *regmap;
+	u32 syscon_idx = 0;
 
 	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
 	if (ret)
@@ -1190,8 +1192,12 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	gmac->regmap_field = devm_regmap_field_alloc(dev, regmap,
-						     *gmac->variant->syscon_field);
+	syscon_field = *gmac->variant->syscon_field;
+	ret = of_property_read_u32_index(pdev->dev.of_node, "syscon", 1,
+					 &syscon_idx);
+	if (!ret)
+		syscon_field.reg += syscon_idx * sizeof(u32);
+	gmac->regmap_field = devm_regmap_field_alloc(dev, regmap, syscon_field);
 	if (IS_ERR(gmac->regmap_field)) {
 		ret = PTR_ERR(gmac->regmap_field);
 		dev_err(dev, "Unable to map syscon register: %d\n", ret);
@@ -1263,6 +1269,8 @@ static const struct of_device_id sun8i_dwmac_match[] = {
 		.data = &emac_variant_a64 },
 	{ .compatible = "allwinner,sun50i-h6-emac",
 		.data = &emac_variant_h6 },
+	{ .compatible = "allwinner,sun50i-h616-emac",
+		.data = &emac_variant_h6 },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Acked-by on v5 16/20
#36 lore raw

Re: [PATCH v5 16/20] net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register

Quoted 10 lines · Andre Przywara

The Allwinner H616 SoC has two EMAC controllers, with the second one being tied to the internal PHY, but also using a separate EMAC clock register.

To tell the driver about which clock register to use, we add a parameter to our syscon phandle. The driver will use this value as an index into the regmap, so that we can address more than the first register, if needed.

Maxime

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#37 lore raw

PATCH v5 17/20 phy: sun4i-usb: Rework HCI PHY (aka. "pmu_unk1") handling

In reply to Andre Przywara

As Icenowy pointed out, newer manuals (starting with H6) actually document the register block at offset 0x800 as "HCI controller and PHY interface", also describe the bits in our "PMU_UNK1" register. Let's put proper names to those "unknown" variables and symbols.

While we are at it, generalise the existing code by allowing a bitmap of bits to clear, to cover newer SoCs: The A100 and H616 use a different bit for the SIDDQ control.

---
 drivers/phy/allwinner/phy-sun4i-usb.c | 29 +++++++++++----------------
 1 file changed, 12 insertions(+), 17 deletions(-)
drivers/phy/allwinner/phy-sun4i-usb.c +12 -17
index 788dd5cdbb7d..539209fe3468 100644
@@ -43,7 +43,7 @@
 #define REG_PHYCTL_A33			0x10
 #define REG_PHY_OTGCTL			0x20
 
-#define REG_PMU_UNK1			0x10
+#define REG_HCI_PHY_CTL			0x10
 
 #define PHYCTL_DATA			BIT(7)
 
@@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
 	int hsic_index;
 	enum sun4i_usb_phy_type type;
 	u32 disc_thresh;
+	u32 hci_phy_ctl_siddq;
 	u8 phyctl_offset;
 	bool dedicated_clocks;
-	bool enable_pmu_unk1;
 	bool phy0_dual_route;
 	int missing_phys;
 };
@@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 		return ret;
 	}
 
+	if (phy->pmu && data->cfg->hci_phy_ctl_siddq) {
+		val = readl(phy->pmu + REG_HCI_PHY_CTL);
+		val &= ~data->cfg->hci_phy_ctl_siddq;
+		writel(val, phy->pmu + REG_HCI_PHY_CTL);
+	}
+
 	if (data->cfg->type == sun8i_a83t_phy ||
 	    data->cfg->type == sun50i_h6_phy) {
 		if (phy->index == 0) {
@@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 			writel(val, data->base + data->cfg->phyctl_offset);
 		}
 	} else {
-		if (phy->pmu && data->cfg->enable_pmu_unk1) {
-			val = readl(phy->pmu + REG_PMU_UNK1);
-			writel(val & ~2, phy->pmu + REG_PMU_UNK1);
-		}
-
 		/* Enable USB 45 Ohm resistor calibration */
 		if (phy->index == 0)
 			sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
@@ -863,7 +864,6 @@ static const struct sun4i_usb_phy_cfg sun4i_a10_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
@@ -872,7 +872,6 @@ static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
 	.disc_thresh = 2,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
@@ -881,7 +880,6 @@ static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
@@ -890,7 +888,6 @@ static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
 	.disc_thresh = 2,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
@@ -899,7 +896,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
@@ -908,7 +904,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
@@ -925,7 +920,7 @@ static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_siddq = BIT(1),
 	.phy0_dual_route = true,
 };
 
@@ -935,7 +930,7 @@ static const struct sun4i_usb_phy_cfg sun8i_r40_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_siddq = BIT(1),
 	.phy0_dual_route = true,
 };
 
@@ -945,7 +940,7 @@ static const struct sun4i_usb_phy_cfg sun8i_v3s_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_siddq = BIT(1),
 	.phy0_dual_route = true,
 };
 
@@ -955,7 +950,7 @@ static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_siddq = BIT(1),
 	.phy0_dual_route = true,
 };
 
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#38 lore raw

PATCH v5 18/20 arm64: dts: allwinner: Add Allwinner H616 .dtsi file

In reply to Andre Przywara

This (relatively) new SoC is similar to the H6, but drops the (broken) PCIe support and the USB 3.0 controller. It also gets the management controller removed, which in turn removes *some*, but not all of the devices formerly dedicated to the ARISC (CPUS).
There does not seem to be an extra interrupt controller anymore, also it lacks the corresponding NMI pin, so no interrupts for the PMIC.

---
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 573 ++++++++++++++++++
 1 file changed, 573 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi new file +573 -0
new file mode 100644
index 000000000000..c277b53f94ea
@@ -0,0 +1,573 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Arm Ltd.
+// based on the H6 dtsi, which is:
+//   Copyright (C) 2017 Icenowy Zheng <[email protected]>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <2>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <3>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 512KiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved: secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x80000>;
+			no-map;
+		};
+	};
+
+	osc24M: osc24M_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "osc24M";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		arm,no-tick-in-suspend;
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x40000000>;
+
+		syscon: syscon@3000000 {
+			compatible = "allwinner,sun50i-h616-system-control";
+			reg = <0x03000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c: sram@28000 {
+				compatible = "mmio-sram";
+				reg = <0x00028000 0x30000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00028000 0x30000>;
+			};
+		};
+
+		ccu: clock@3001000 {
+			compatible = "allwinner,sun50i-h616-ccu";
+			reg = <0x03001000 0x1000>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		watchdog: watchdog@30090a0 {
+			compatible = "allwinner,sun50i-h616-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x030090a0 0x20>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+			status = "okay";
+		};
+
+		pio: pinctrl@300b000 {
+			compatible = "allwinner,sun50i-h616-pinctrl";
+			reg = <0x0300b000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			ext_rgmii_pins: rgmii-pins {
+				pins = "PI0", "PI1", "PI2", "PI3", "PI4",
+				       "PI5", "PI7", "PI8", "PI9", "PI10",
+				       "PI11", "PI12", "PI13", "PI14", "PI15",
+				       "PI16";
+				function = "emac0";
+				drive-strength = <40>;
+			};
+
+			i2c0_pins: i2c0-pins {
+				pins = "PI6", "PI7";
+				function = "i2c0";
+			};
+
+			i2c3_ph_pins: i2c3-ph-pins {
+				pins = "PH4", "PH5";
+				function = "i2c3";
+			};
+
+			ir_rx_pin: ir-rx-pin {
+				pins = "PH10";
+				function = "ir_rx";
+			};
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC0", "PC1", "PC5", "PC6",
+				       "PC8", "PC9", "PC10", "PC11",
+				       "PC13", "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			spi0_pins: spi0-pins {
+				pins = "PC0", "PC2", "PC3", "PC4";
+				function = "spi0";
+			};
+
+			spi1_pins: spi1-pins {
+				pins = "PH6", "PH7", "PH8";
+				function = "spi1";
+			};
+
+			spi1_cs_pin: spi1-cs-pin {
+				pins = "PH5";
+				function = "spi1";
+			};
+
+			uart0_ph_pins: uart0-ph-pins {
+				pins = "PH0", "PH1";
+				function = "uart0";
+			};
+
+			uart1_pins: uart1-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			uart1_rts_cts_pins: uart1-rts-cts-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
+		};
+
+		gic: interrupt-controller@3021000 {
+			compatible = "arm,gic-400";
+			reg = <0x03021000 0x1000>,
+			      <0x03022000 0x2000>,
+			      <0x03024000 0x2000>,
+			      <0x03026000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		mmc0: mmc@4020000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04020000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			mmc-ddr-1_8v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@4021000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04021000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
+			status = "disabled";
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			mmc-ddr-1_8v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@4022000 {
+			compatible = "allwinner,sun50i-h616-emmc",
+				     "allwinner,sun50i-a100-emmc";
+			reg = <0x04022000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
+			status = "disabled";
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			mmc-ddr-1_8v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		uart0: serial@5000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@5000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@5000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@5000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@5001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			status = "disabled";
+		};
+
+		uart5: serial@5001400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001400 0x400>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART5>;
+			resets = <&ccu RST_BUS_UART5>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@5002000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002000 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@5002400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002400 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@5002800 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002800 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c3: i2c@5002c00 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002c00 0x400>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c4: i2c@5003000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05003000 0x400>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C4>;
+			resets = <&ccu RST_BUS_I2C4>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@5010000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05010000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@5011000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05011000 0x1000>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac0: ethernet@5020000 {
+			compatible = "allwinner,sun50i-h616-emac",
+				     "allwinner,sun50i-a64-emac";
+			syscon = <&syscon>;
+			reg = <0x05020000 0x10000>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC0>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC0>;
+			clock-names = "stmmaceth";
+			status = "disabled";
+
+			mdio0: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		rtc: rtc@7000000 {
+			compatible = "allwinner,sun50i-h616-rtc",
+				     "allwinner,sun50i-h6-rtc";
+			reg = <0x07000000 0x400>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clock-output-names = "osc32k", "osc32k-out", "iosc";
+			#clock-cells = <1>;
+		};
+
+		r_ccu: clock@7010000 {
+			compatible = "allwinner,sun50i-h616-r-ccu";
+			reg = <0x07010000 0x210>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+				 <&ccu CLK_PLL_PERIPH0>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		r_pio: pinctrl@7022000 {
+			compatible = "allwinner,sun50i-h616-r-pinctrl";
+			reg = <0x07022000 0x400>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			r_i2c_pins: r-i2c-pins {
+				pins = "PL0", "PL1";
+				function = "s_i2c";
+			};
+
+			r_rsb_pins: r-rsb-pins {
+				pins = "PL0", "PL1";
+				function = "s_rsb";
+			};
+		};
+
+		ir: ir@7040000 {
+				compatible = "allwinner,sun50i-h616-ir",
+					     "allwinner,sun6i-a31-ir";
+				reg = <0x07040000 0x400>;
+				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&r_ccu CLK_R_APB1_IR>,
+					 <&r_ccu CLK_IR>;
+				clock-names = "apb", "ir";
+				resets = <&r_ccu RST_R_APB1_IR>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&ir_rx_pin>;
+				status = "disabled";
+		};
+
+		r_i2c: i2c@7081400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x07081400 0x400>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			resets = <&r_ccu RST_R_APB2_I2C>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		r_rsb: rsb@7083000 {
+			compatible = "allwinner,sun50i-h616-rsb",
+				     "allwinner,sun8i-a23-rsb";
+			reg = <0x07083000 0x400>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_RSB>;
+			clock-frequency = <3000000>;
+			resets = <&r_ccu RST_R_APB2_RSB>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_rsb_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
Signature · 1 line
2.17.5
#39 lore raw

PATCH v5 19/20 dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding

In reply to Andre Przywara
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/arm/sunxi.yaml +5 -0
index 08607c7ec1bf..aeb8771b14c4 100644
@@ -932,4 +932,9 @@ properties:
           - const: xunlong,orangepi-zero-plus2-h3
           - const: allwinner,sun8i-h3
 
+      - description: Xunlong OrangePi Zero 2
+        items:
+          - const: xunlong,orangepi-zero2
+          - const: allwinner,sun50i-h616
+
 additionalProperties: true
Signature · 7 lines
2.17.5


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#40 lore raw

PATCH v5 20/20 arm64: dts: allwinner: Add OrangePi Zero 2 .dts

In reply to Andre Przywara

The OrangePi Zero 2 is a development board with the new H616 SoC.

It features the usual connectors used on those small boards, and comes with the AXP305, which seems to be compatible with the AXP805.

For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2

---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 203 ++++++++++++++++++
 2 files changed, 204 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
arch/arm64/boot/dts/allwinner/Makefile +1 -0
index 41ce680e5f8d..9ba4b5d92657 100644
@@ -36,3 +36,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts new file +203 -0

203 lines not on this page · raw message

Signature · 1 line
2.17.5