wifi: rtl8xxxu: Register the LED and make it blink
PATCH v2 1/4 wifi: rtl8xxxu: Register the LED and make it blink
If the chip can have an LED, register a struct led_classdev and enable hardware-controlled blinking. When the chip is not transmitting or receiving anything the LED is off. Otherwise the LED will blink faster or slower according to the throughput.
The LED can be controlled from userspace by writing 0, 1, or 2 to /sys/class/leds/rtl8xxxu-usbX-Y/brightness:
0 - solid off.
1 - solid on.
2 - hardware-controlled blinking.
In this patch none of the chips advertise having an LED. That will be added in the next patches.
---
v2:
- Suggestion from Ping-Ke Shih:
- Check for led_classdev_brightness_set inside rtl8xxxu_init_led() and for led_registered inside rtl8xxxu_deinit_led() instead of checking for them in the caller functions.
--- .../net/wireless/realtek/rtl8xxxu/rtl8xxxu.h | 8 ++++ .../wireless/realtek/rtl8xxxu/rtl8xxxu_core.c | 38 +++++++++++++++++++ 2 files changed, 46 insertions(+)
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h +8 -0
@@ -1443,6 +1443,8 @@ struct rtl8xxxu_cfo_tracking {u32 packet_count_pre; }; +#define RTL8XXXU_HW_LED_CONTROL 2 +struct rtl8xxxu_priv {struct ieee80211_hw *hw;struct usb_device *udev;
@@ -1564,6 +1566,10 @@ struct rtl8xxxu_priv {struct rtl8xxxu_ra_report ra_report;struct rtl8xxxu_cfo_tracking cfo_tracking;struct rtl8xxxu_ra_info ra_info; + +bool led_registered; +char led_name[32 ]; +struct led_classdev led_cdev; };struct rtl8xxxu_rx_urb {
@@ -1613,6 +1619,8 @@ struct rtl8xxxu_fileops { u32 rts_rate);void (*set_crystal_cap) (struct rtl8xxxu_priv *priv,u8 crystal_cap);s8 (*cck_rssi) (struct rtl8xxxu_priv *priv,u8 cck_agc_rpt); +int (*led_classdev_brightness_set) (struct led_classdev *led_cdev, +enum led_brightness brightness);int writeN_block_size;int rx_agg_buf_size;char tx_desc_size;
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c +38 -0
@@ -6955,6 +6955,40 @@ static int rtl8xxxu_parse_usb(struct rtl8xxxu_priv *priv,return ret; } +static void rtl8xxxu_init_led (struct rtl8xxxu_priv *priv) +{ +struct led_classdev *led = &priv->led_cdev; + +if (!priv->fops->led_classdev_brightness_set) +return ; + + led->brightness_set_blocking = priv->fops->led_classdev_brightness_set; + +snprintf (priv->led_name,sizeof (priv->led_name), +"rtl8xxxu-usb%s" ,dev_name (&priv->udev->dev)); + led->name = priv->led_name; + led->max_brightness =RTL8XXXU_HW_LED_CONTROL ; + +if (led_classdev_register (&priv->udev->dev, led)) +return ; + + priv->led_registered = true; + + led->brightness = led->max_brightness; + priv->fops->led_classdev_brightness_set (led, led->brightness); +} + +static void rtl8xxxu_deinit_led (struct rtl8xxxu_priv *priv) +{ +struct led_classdev *led = &priv->led_cdev; + +if (!priv->led_registered) +return ; + + priv->fops->led_classdev_brightness_set (led,LED_OFF ); +led_classdev_unregister (led); +} +static int rtl8xxxu_probe (struct usb_interface *interface,const struct usb_device_id *id) {
@@ -7135,6 +7169,8 @@ static int rtl8xxxu_probe(struct usb_interface *interface, goto err_set_intfdata; } +rtl8xxxu_init_led (priv); +return 0 ; err_set_intfdata:
@@ -7159,6 +7195,8 @@ static void rtl8xxxu_disconnect(struct usb_interface *interface) hw =usb_get_intfdata (interface); priv = hw->priv; +rtl8xxxu_deinit_led (priv); +ieee80211_unregister_hw (hw); priv->fops->power_off (priv);
Signature · 1 line
2.39.1
PATCH v2 2/4 wifi: rtl8xxxu: Add LED control code for RTL8188EU
By default the LED will blink when there is some activity.
This was tested with a TP-Link TL-WN725N.
---
v2:
- No change.
--- .../realtek/rtl8xxxu/rtl8xxxu_8188e.c | 25 +++++++++++++++++++ .../wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h | 4 +++ 2 files changed, 29 insertions(+)
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8188e.c +25 -0
@@ -1350,6 +1350,30 @@ static s8 rtl8188e_cck_rssi(struct rtl8xxxu_priv *priv, u8 cck_agc_rpt)return rx_pwr_all; } +static int rtl8188eu_led_brightness_set (struct led_classdev *led_cdev, +enum led_brightness brightness) +{ +struct rtl8xxxu_priv *priv =container_of (led_cdev, + struct rtl8xxxu_priv, + led_cdev); +u8 ledcfg =rtl8xxxu_read8 (priv,REG_LEDCFG2 ); + +if (brightness ==LED_OFF ) { + ledcfg &= ~LEDCFG2_HW_LED_CONTROL ; + ledcfg |=LEDCFG2_SW_LED_CONTROL |LEDCFG2_SW_LED_DISABLE ; + }else if (brightness ==LED_ON ) { + ledcfg &= ~(LEDCFG2_HW_LED_CONTROL |LEDCFG2_SW_LED_DISABLE ); + ledcfg |=LEDCFG2_SW_LED_CONTROL ; + }else if (brightness ==RTL8XXXU_HW_LED_CONTROL ) { + ledcfg &= ~LEDCFG2_SW_LED_DISABLE ; + ledcfg |=LEDCFG2_HW_LED_CONTROL |LEDCFG2_HW_LED_ENABLE ; + } + +rtl8xxxu_write8 (priv,REG_LEDCFG2 , ledcfg); + +return 0 ; +} +static void rtl8188e_set_tx_rpt_timing (struct rtl8xxxu_ra_info *ra,u8 timing) {u8 idx;
@@ -1851,6 +1875,7 @@ struct rtl8xxxu_fileops rtl8188eu_fops = { .fill_txdesc = rtl8xxxu_fill_txdesc_v3, .set_crystal_cap = rtl8188f_set_crystal_cap, .cck_rssi = rtl8188e_cck_rssi, + .led_classdev_brightness_set = rtl8188eu_led_brightness_set, .writeN_block_size = 128, .rx_desc_size = sizeof(struct rtl8xxxu_rxdesc16), .tx_desc_size = sizeof(struct rtl8xxxu_txdesc32),
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h +4 -0
@@ -148,6 +148,10 @@#define LEDCFG0_DPDT_SELECT BIT(23)#define REG_LEDCFG1 0x004d#define REG_LEDCFG2 0x004e +#define LEDCFG2_HW_LED_CONTROL BIT(1) +#define LEDCFG2_HW_LED_ENABLE BIT(5) +#define LEDCFG2_SW_LED_DISABLE BIT(3) +#define LEDCFG2_SW_LED_CONTROL BIT(5)#define LEDCFG2_DPDT_SELECT BIT(7)#define REG_LEDCFG3 0x004f#define REG_LEDCFG REG_LEDCFG2
Signature · 1 line
2.39.1
Re: [PATCH v2 2/4] wifi: rtl8xxxu: Add LED control code for RTL8188EU
Quoted 5 lines · Bitterblue Smith
By default the LED will blink when there is some activity.
This was tested with a TP-Link TL-WN725N.
Signed-off-by Bitterblue Smith <[email protected]>
[...]
PATCH v2 3/4 wifi: rtl8xxxu: Add LED control code for RTL8192EU
In reply to Bitterblue SmithBy default the LED will blink when there is some activity.
This was tested with a cheap "HT-WR813" from Aliexpress.
---
v2:
- No change.
--- .../realtek/rtl8xxxu/rtl8xxxu_8192e.c | 24 +++++++++++++++++++ .../wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h | 2 ++ 2 files changed, 26 insertions(+)
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c +24 -0
@@ -1764,6 +1764,29 @@ static s8 rtl8192e_cck_rssi(struct rtl8xxxu_priv *priv, u8 cck_agc_rpt)return rx_pwr_all; } +static int rtl8192eu_led_brightness_set (struct led_classdev *led_cdev, +enum led_brightness brightness) +{ +struct rtl8xxxu_priv *priv =container_of (led_cdev, + struct rtl8xxxu_priv, + led_cdev); +u8 ledcfg =rtl8xxxu_read8 (priv,REG_LEDCFG1 ); + +if (brightness ==LED_OFF ) { + ledcfg &= ~LEDCFG1_HW_LED_CONTROL ; + ledcfg |=LEDCFG1_LED_DISABLE ; + }else if (brightness ==LED_ON ) { + ledcfg &= ~(LEDCFG1_HW_LED_CONTROL |LEDCFG1_LED_DISABLE ); + }else if (brightness ==RTL8XXXU_HW_LED_CONTROL ) { + ledcfg &= ~LEDCFG1_LED_DISABLE ; + ledcfg |=LEDCFG1_HW_LED_CONTROL ; + } + +rtl8xxxu_write8 (priv,REG_LEDCFG1 , ledcfg); + +return 0 ; +} +struct rtl8xxxu_fileops rtl8192eu_fops = { .identify_chip = rtl8192eu_identify_chip, .parse_efuse = rtl8192eu_parse_efuse,
@@ -1788,6 +1811,7 @@ struct rtl8xxxu_fileops rtl8192eu_fops = { .fill_txdesc = rtl8xxxu_fill_txdesc_v2, .set_crystal_cap = rtl8723a_set_crystal_cap, .cck_rssi = rtl8192e_cck_rssi, + .led_classdev_brightness_set = rtl8192eu_led_brightness_set, .writeN_block_size = 128, .tx_desc_size = sizeof(struct rtl8xxxu_txdesc40), .rx_desc_size = sizeof(struct rtl8xxxu_rxdesc24),
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h +2 -0
@@ -147,6 +147,8 @@#define REG_LEDCFG0 0x004c#define LEDCFG0_DPDT_SELECT BIT(23)#define REG_LEDCFG1 0x004d +#define LEDCFG1_HW_LED_CONTROL BIT(1) +#define LEDCFG1_LED_DISABLE BIT(7)#define REG_LEDCFG2 0x004e#define LEDCFG2_HW_LED_CONTROL BIT(1)#define LEDCFG2_HW_LED_ENABLE BIT(5)
Signature · 1 line
2.39.1
Re: [PATCH v2 3/4] wifi: rtl8xxxu: Add LED control code for RTL8192EU
Quoted 6 lines · Bitterblue Smith
By default the LED will blink when there is some activity.
This was tested with a cheap "HT-WR813" from Aliexpress.
Signed-off-by Bitterblue Smith <[email protected]>
PATCH v2 4/4 wifi: rtl8xxxu: Add LED control code for RTL8723AU
In reply to Bitterblue SmithBy default the LED will blink when there is some activity.
This is only compile tested.
---
v2:
- No change.
--- .../realtek/rtl8xxxu/rtl8xxxu_8723a.c | 25 +++++++++++++++++++ 1 file changed, 25 insertions(+)
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723a.c +25 -0
@@ -457,6 +457,30 @@ s8 rtl8723a_cck_rssi(struct rtl8xxxu_priv *priv, u8 cck_agc_rpt)return rx_pwr_all; } +static int rtl8723au_led_brightness_set (struct led_classdev *led_cdev, +enum led_brightness brightness) +{ +struct rtl8xxxu_priv *priv =container_of (led_cdev, + struct rtl8xxxu_priv, + led_cdev); +u8 ledcfg =rtl8xxxu_read8 (priv,REG_LEDCFG2 ); + +if (brightness ==LED_OFF ) { + ledcfg &= ~LEDCFG2_HW_LED_CONTROL ; + ledcfg |=LEDCFG2_SW_LED_CONTROL |LEDCFG2_SW_LED_DISABLE ; + }else if (brightness ==LED_ON ) { + ledcfg &= ~(LEDCFG2_HW_LED_CONTROL |LEDCFG2_SW_LED_DISABLE ); + ledcfg |=LEDCFG2_SW_LED_CONTROL ; + }else if (brightness ==RTL8XXXU_HW_LED_CONTROL ) { + ledcfg &= ~LEDCFG2_SW_LED_DISABLE ; + ledcfg |=LEDCFG2_HW_LED_CONTROL |LEDCFG2_HW_LED_ENABLE ; + } + +rtl8xxxu_write8 (priv,REG_LEDCFG2 , ledcfg); + +return 0 ; +} +struct rtl8xxxu_fileops rtl8723au_fops = { .identify_chip = rtl8723au_identify_chip, .parse_efuse = rtl8723au_parse_efuse,
@@ -482,6 +506,7 @@ struct rtl8xxxu_fileops rtl8723au_fops = { .fill_txdesc = rtl8xxxu_fill_txdesc_v1, .set_crystal_cap = rtl8723a_set_crystal_cap, .cck_rssi = rtl8723a_cck_rssi, + .led_classdev_brightness_set = rtl8723au_led_brightness_set, .writeN_block_size = 1024, .rx_agg_buf_size = 16000, .tx_desc_size = sizeof(struct rtl8xxxu_txdesc32),
Signature · 1 line
2.39.1
Re: [PATCH v2 4/4] wifi: rtl8xxxu: Add LED control code for RTL8723AU
Quoted 6 lines · Bitterblue Smith
By default the LED will blink when there is some activity.
This is only compile tested.
Signed-off-by Bitterblue Smith <[email protected]>
Quoted 11 lines · Bitterblue Smith
If the chip can have an LED, register a struct
led_classdevand enable hardware-controlled blinking. When the chip is not transmitting or receiving anything the LED is off. Otherwise the LED will blink faster or slower according to the throughput.The LED can be controlled from userspace by writing 0, 1, or 2 to
/sys/class/leds/rtl8xxxu-usbX-Y/brightness:
0 - solid off.
1 - solid on.
2 - hardware-controlled blinking.
Quoted 4 lines
In this patch none of the chips advertise having an LED. That will be added in the next patches.
Signed-off-by Bitterblue Smith <[email protected]>
Quoted 7 lines
---
v2:
- Suggestion from Ping-Ke Shih:
- Check forled_classdev_brightness_setinsidertl8xxxu_init_led()and forled_registeredinsidertl8xxxu_deinit_led()instead of checking for them in the caller functions.
[...]
Quoted 11 lines · Bitterblue Smith
If the chip can have an LED, register a struct
led_classdevand enable hardware-controlled blinking. When the chip is not transmitting or receiving anything the LED is off. Otherwise the LED will blink faster or slower according to the throughput.The LED can be controlled from userspace by writing 0, 1, or 2 to
/sys/class/leds/rtl8xxxu-usbX-Y/brightness:
0 - solid off.
1 - solid on.
2 - hardware-controlled blinking.
Quoted 5 lines
In this patch none of the chips advertise having an LED. That will be added in the next patches.
Signed-off-by Bitterblue Smith <[email protected]>Reviewed-by Ping-Ke Shih <[email protected]>
4 patches applied to wireless-next.git, thanks.
3be01622995b wifi: rtl8xxxu: Register the LED and make it blink 873b3811728b wifi: rtl8xxxu: Add LED control code for RTL8188EU ae0a6df673c2 wifi: rtl8xxxu: Add LED control code for RTL8192EU 2cef0aeebf2c wifi: rtl8xxxu: Add LED control code for RTL8723AU
Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches