Generate device tree node for pci devices
Subsystems (2)
v9 cover Generate device tree node for pci devices
This patch series introduces OF overlay support for PCI devices which primarily addresses two use cases. First, it provides a data driven method to describe hardware peripherals that are present in a PCI endpoint and hence can be accessed by the PCI host. Second, it allows reuse of a OF compatible driver -- often used in SoC platforms -- in a PCI host based system.
There are 2 series devices rely on this patch:
1) Xilinx Alveo Accelerator cards (FPGA based device)
2) Microchip LAN9662 Ethernet Controller
Please see: https://lore.kernel.org/lkml/[email protected]/
Normally, the PCI core discovers PCI devices and their BARs using the PCI enumeration process. However, the process does not provide a way to discover the hardware peripherals that are present in a PCI device, and which can be accessed through the PCI BARs. Also, the enumeration process does not provide a way to associate MSI-X vectors of a PCI device with the hardware peripherals that are present in the device. PCI device drivers often use header files to describe the hardware peripherals and their resources as there is no standard data driven way to do so. This patch series proposes to use flattened device tree blob to describe the peripherals in a data driven way. Based on previous discussion, using device tree overlay is the best way to unflatten the blob and populate platform devices. To use device tree overlay, there are three obvious problems that need to be resolved.
First, we need to create a base tree for non-DT system such as x86_64. A patch series has been submitted for this:
https://lore.kernel.org/lkml/[email protected]/
https://lore.kernel.org/lkml/[email protected]/
Second, a device tree node corresponding to the PCI endpoint is required for overlaying the flattened device tree blob for that PCI endpoint. Because PCI is a self-discoverable bus, a device tree node is usually not created for PCI devices. This series adds support to generate a device tree node for a PCI device which advertises itself using PCI quirks infrastructure.
Third, we need to generate device tree nodes for PCI bridges since a child PCI endpoint may choose to have a device tree node created.
This patch series is made up of three patches.
The first patch is adding OF interface to create or destroy OF node dynamically.
The second patch introduces a kernel option, CONFIG_DYNAMIC_PCI_OF_NODEX. When the option is turned on, the kernel will generate device tree nodes for all PCI bridges unconditionally. The patch also shows how to use the PCI quirks infrastructure, DECLARE_PCI_FIXUP_FINAL to generate a device tree node for a device. Specifically, the patch generates a device tree node for Xilinx Alveo U50 PCIe accelerator device. The generated device tree nodes do not have any property.
The third patch adds basic properties ('reg', 'compatible' and 'device_type') to the dynamically generated device tree nodes. More properties can be added in the future.
Here is the example of device tree nodes generated within the ARM64 QEMU.
# lspci -t
-[0000:00]-+-00.0
+-01.0
+-03.0-[01-03]----00.0-[02-03]----00.0-[03]----00.0
+-03.1-[04]--
\-04.0-[05-06]----00.0-[06]--
# tree /sys/firmware/devicetree/base/pcie\@10000000
/sys/firmware/devicetree/base/pcie@10000000
|-- #address-cells
|-- #interrupt-cells
|-- #size-cells
|-- bus-range
|-- compatible
|-- device_type
|-- dma-coherent
|-- interrupt-map
|-- interrupt-map-mask
|-- linux,pci-domain
|-- msi-map
|-- name
|-- pci@3,0
| |-- #address-cells
| |-- #size-cells
| |-- compatible
| |-- device_type
| |-- pci@0,0
| | |-- #address-cells
| | |-- #size-cells
| | |-- compatible
| | |-- device_type
| | |-- pci@0,0
| | | |-- #address-cells
| | | |-- #size-cells
| | | |-- compatible
| | | |-- dev@0,0
| | | | |-- #address-cells
| | | | |-- #size-cells
| | | | |-- compatible
| | | | |-- ranges
| | | | `-- reg
| | | |-- device_type
| | | |-- ranges
| | | `-- reg
| | |-- ranges
| | `-- reg
| |-- ranges
| `-- reg
|-- pci@3,1
| |-- #address-cells
| |-- #size-cells
| |-- compatible
| |-- device_type
| |-- ranges
| `-- reg
|-- pci@4,0
| |-- #address-cells
| |-- #size-cells
| |-- compatible
| |-- device_type
| |-- pci@0,0
| | |-- #address-cells
| | |-- #size-cells
| | |-- compatible
| | |-- device_type
| | |-- ranges
| | `-- reg
| |-- ranges
| `-- reg
|-- ranges
`-- regChanges since v9:
- Minor code review fixes
Changes since v8:
- Added patches to create unit test to verifying address translation The test relies on QEMU PCI Test Device, please see
https://github.com/houlz0507/xoclv2/blob/pci-dt-0329/pci-dt-patch-0329/README
for test setup
- Minor code review fixes
Changes since v7:
- Modified dynamic node creation interfaces
- Added unittest for new added interfaces
Changes since v6:
- Removed single line wrapper functions
- Added Signed-off-by Clément Léger <[email protected]>
Changes since v5:
- Fixed code review comments
- Fixed incorrect 'ranges' and 'reg' properties
Changes since RFC v4:
- Fixed code review comments
Changes since RFC v3:
- Split the Xilinx Alveo U50 PCI quirk to a separate patch
- Minor changes in commit description and code comment
Changes since RFC v2:
- Merged patch 3 with patch 2
- Added OF interfaces of_changeset_add_prop_* and use them to create properties.
- Added '#address-cells', '#size-cells' and 'ranges' properties.
Changes since RFC v1:
- Added one patch to create basic properties.
- To move DT related code out of PCI subsystem, replaced of_node_alloc() with of_create_node()/of_destroy_node()
Lizhi Hou (5):
of: dynamic: Add interfaces for creating device node dynamically
PCI: Create device tree node for selected devices
PCI: Add PCI quirks to generate device tree node for Xilinx Alveo U50
of: overlay: Extend of_overlay_fdt_apply() to specify the target node
of: unittest: Add pci_dt_testdrv pci driver
drivers/of/dynamic.c | 164 ++++++++++++++ drivers/of/overlay.c | 42 +++- drivers/of/unittest-data/Makefile | 3 +- .../of/unittest-data/overlay_pci_node.dtso | 22 ++ drivers/of/unittest.c | 210 +++++++++++++++++- drivers/pci/Kconfig | 12 + drivers/pci/Makefile | 1 + drivers/pci/bus.c | 2 + drivers/pci/of.c | 81 ++++++- drivers/pci/of_property.c | 194 ++++++++++++++++ drivers/pci/pci.h | 19 ++ drivers/pci/quirks.c | 12 + drivers/pci/remove.c | 1 + include/linux/of.h | 25 ++- 14 files changed, 772 insertions(+), 16 deletions(-) create mode 100644 drivers/of/unittest-data/overlay_pci_node.dtso create mode 100644 drivers/pci/of_property.c
Signature · 1 line
2.34.1
PATCH v9 1/5 of: dynamic: Add interfaces for creating device node dynamically
of_changeset_create_node() creates device node dynamically and attaches the newly created node to a changeset.
Expand of_changeset APIs to handle specific types of properties.
of_changeset_add_prop_string()
of_changeset_add_prop_string_array()
of_changeset_add_prop_u32_array()--- drivers/of/dynamic.c | 164 ++++++++++++++++++++++++++++++++++++++++++ drivers/of/unittest.c | 19 ++++- include/linux/of.h | 23 ++++++ 3 files changed, 205 insertions(+), 1 deletion(-)
drivers/of/dynamic.c +164 -0
@@ -487,6 +487,38 @@ struct device_node *__of_node_dup(const struct device_node *np,return NULL ; } +/** +* of_changeset_create_node - Dynamically create a device node and attach to +* a given changeset. +* +* @parent: Pointer to parent device node +* @full_name: Node full name +* @cset: Pointer to changeset +* +* Return: Pointer to the created device node or NULL in case of an error. +*/ +struct device_node *of_changeset_create_node (struct device_node *parent, +const char *full_name, +struct of_changeset *cset) +{ +struct device_node *np; +int ret; + + np =__of_node_dup (NULL , full_name); +if (!np) +return NULL ; + np->parent = parent; + + ret =of_changeset_attach_node (cset, np); +if (ret) { +of_node_put (np); +return NULL ; + } + +return np; +} +EXPORT_SYMBOL (of_changeset_create_node); +static void __of_changeset_entry_destroy (struct of_changeset_entry *ce) { if (ce->action == OF_RECONFIG_ATTACH_NODE &&
@@ -960,3 +992,135 @@ int of_changeset_action(struct of_changeset *ocs, unsigned long action,return 0 ; }EXPORT_SYMBOL_GPL (of_changeset_action); + +static int of_changeset_add_prop_helper (struct of_changeset *ocs, +struct device_node *np, +const struct property *pp) +{ +struct property *new_pp; +int ret; + + new_pp =__of_prop_dup (pp,GFP_KERNEL ); +if (!new_pp) +return -ENOMEM ; + + ret =of_changeset_add_property (ocs, np, new_pp); +if (ret) { +kfree (new_pp->name); +kfree (new_pp->value); +kfree (new_pp); + } + +return ret; +} + +/** +* of_changeset_add_prop_string - Add a string property to a changeset +* +* @ocs: changeset pointer +* @np: device node pointer +* @prop_name: name of the property to be added +* @str: pointer to null terminated string +* +* Create a string property and add it to a changeset. +* +* Return: 0 on success, a negative error value in case of an error. +*/ +int of_changeset_add_prop_string (struct of_changeset *ocs, +struct device_node *np, +const char *prop_name,const char *str) +{ +struct property prop; + + prop.name = (char *)prop_name; + prop.length =strlen (str) +1 ; + prop.value = (void *)str; + +return of_changeset_add_prop_helper (ocs, np, &prop); +} +EXPORT_SYMBOL_GPL (of_changeset_add_prop_string); + +/** +* of_changeset_add_prop_string_array - Add a string list property to +* a changeset +* +* @ocs: changeset pointer +* @np: device node pointer +* @prop_name: name of the property to be added +* @str_array: pointer to an array of null terminated strings +* @sz: number of string array elements +* +* Create a string list property and add it to a changeset. +* +* Return: 0 on success, a negative error value in case of an error. +*/ +int of_changeset_add_prop_string_array (struct of_changeset *ocs, +struct device_node *np, +const char *prop_name, +const char **str_array,size_t sz) +{ +struct property prop; +int i, ret; +char *vp; + + prop.name = (char *)prop_name; + + prop.length =0 ; +for (i =0 ; i < sz; i++) + prop.length +=strlen (str_array[i]) +1 ; + + prop.value =kmalloc (prop.length,GFP_KERNEL ); +if (!prop.value) +return -ENOMEM ; + + vp = prop.value; +for (i =0 ; i < sz; i++) { + vp +=snprintf (vp, (char *)prop.value + prop.length - vp,"%s" , + str_array[i]) +1 ; + } + ret =of_changeset_add_prop_helper (ocs, np, &prop); +kfree (prop.value); + +return ret; +} +EXPORT_SYMBOL_GPL (of_changeset_add_prop_string_array); + +/** +* of_changeset_add_prop_u32_array - Add a property of 32 bit integers +* property to a changeset +* +* @ocs: changeset pointer +* @np: device node pointer +* @prop_name: name of the property to be added +* @array: pointer to an array of 32 bit integers +* @sz: number of array elements +* +* Create a property of 32 bit integers and add it to a changeset. +* +* Return: 0 on success, a negative error value in case of an error. +*/ +int of_changeset_add_prop_u32_array (struct of_changeset *ocs, +struct device_node *np, +const char *prop_name, +const u32 *array,size_t sz) +{ +struct property prop; +__be32 *val; +int i, ret; + + val =kcalloc (sz,sizeof (__be32),GFP_KERNEL ); +if (!val) +return -ENOMEM ; + +for (i =0 ; i < sz; i++) + val[i] =cpu_to_be32 (array[i]); + prop.name = (char *)prop_name; + prop.length =sizeof (u32) * sz; + prop.value = (void *)val; + + ret =of_changeset_add_prop_helper (ocs, np, &prop); +kfree (val); + +return ret; +} +EXPORT_SYMBOL_GPL (of_changeset_add_prop_u32_array);
drivers/of/unittest.c +18 -1
@@ -802,7 +802,9 @@ static void __init of_unittest_changeset(void)struct property *ppname_n21, pname_n21 = { .name ="name" , .length =3 , .value ="n21" };struct property *ppupdate, pupdate = { .name ="prop-update" , .length =5 , .value ="abcd" };struct property *ppremove; -struct device_node *n1, *n2, *n21, *nchangeset, *nremove, *parent, *np; +struct device_node *n1, *n2, *n21, *n22, *nchangeset, *nremove, *parent, *np; +static const char *const str_array[] = {"str1" ,"str2" ,"str3" }; +const u32 u32_array[] = {1 ,2 ,3 };struct of_changeset chgset; n1 =__of_node_dup (NULL ,"n1" );
@@ -857,6 +859,17 @@ static void __init of_unittest_changeset(void)unittest (!of_changeset_add_property (&chgset, parent, ppadd),"fail add prop prop-add\n" );unittest (!of_changeset_update_property (&chgset, parent, ppupdate),"fail update prop\n" );unittest (!of_changeset_remove_property (&chgset, parent, ppremove),"fail remove prop\n" ); + n22 =of_changeset_create_node (n2,"n22" , &chgset); +unittest (n22,"fail create n22\n" ); +unittest (!of_changeset_add_prop_string (&chgset, n22,"prop-str" ,"abcd" ), +"fail add prop prop-str" ); +unittest (!of_changeset_add_prop_string_array (&chgset, n22,"prop-str-array" , + (const char **)str_array, +ARRAY_SIZE (str_array)), +"fail add prop prop-str-array" ); +unittest (!of_changeset_add_prop_u32_array (&chgset, n22,"prop-u32-array" , + u32_array,ARRAY_SIZE (u32_array)), +"fail add prop prop-u32-array" );unittest (!of_changeset_apply (&chgset),"apply failed\n" );
@@ -866,6 +879,9 @@ static void __init of_unittest_changeset(void)unittest ((np =of_find_node_by_path ("/testcase-data/changeset/n2/n21" )),"'%pOF' not added\n" , n21);of_node_put (np); +unittest ((np =of_find_node_by_path ("/testcase-data/changeset/n2/n22" )), +"'%pOF' not added\n" , n22); +of_node_put (np);unittest (!of_changeset_revert (&chgset),"revert failed\n" );
@@ -874,6 +890,7 @@ static void __init of_unittest_changeset(void)of_node_put (n1);of_node_put (n2);of_node_put (n21); +of_node_put (n22);#endif }
include/linux/of.h +23 -0
@@ -1580,6 +1580,29 @@ static inline int of_changeset_update_property(struct of_changeset *ocs, {return of_changeset_action (ocs,OF_RECONFIG_UPDATE_PROPERTY , np, prop); } + +struct device_node *of_changeset_create_node (struct device_node *parent, +const char *full_name, +struct of_changeset *cset); +int of_changeset_add_prop_string (struct of_changeset *ocs, +struct device_node *np, +const char *prop_name,const char *str); +int of_changeset_add_prop_string_array (struct of_changeset *ocs, +struct device_node *np, +const char *prop_name, +const char **str_array,size_t sz); +int of_changeset_add_prop_u32_array (struct of_changeset *ocs, +struct device_node *np, +const char *prop_name, +const u32 *array,size_t sz); +static inline int of_changeset_add_prop_u32 (struct of_changeset *ocs, +struct device_node *np, +const char *prop_name, +const u32 val) +{ +return of_changeset_add_prop_u32_array (ocs, np, prop_name, &val,1 ); +} +#else /* CONFIG_OF_DYNAMIC */ static inline int of_reconfig_notifier_register (struct notifier_block *nb) {
Signature · 1 line
2.34.1
PATCH v9 2/5 PCI: Create device tree node for selected devices
In reply to Lizhi HouThe PCI endpoint device such as Xilinx Alveo PCI card maps the register spaces from multiple hardware peripherals to its PCI BAR. Normally, the PCI core discovers devices and BARs using the PCI enumeration process. There is no infrastructure to discover the hardware peripherals that are present in a PCI device, and which can be accessed through the PCI BARs.
For Alveo PCI card, the card firmware provides a flattened device tree to describe the hardware peripherals on its BARs. The Alveo card driver can load this flattened device tree and leverage device tree framework to generate platform devices for the hardware peripherals eventually.
Apparently, the device tree framework requires a device tree node for the PCI device. Thus, it can generate the device tree nodes for hardware peripherals underneath. Because PCI is self discoverable bus, there might not be a device tree node created for PCI devices. This patch is to add support to generate device tree node for PCI devices.
Added a kernel option. When the option is turned on, the kernel will generate device tree nodes for PCI bridges unconditionally.
Initially, the basic properties are added for the dynamically generated device tree nodes.
--- drivers/pci/Kconfig | 12 +++ drivers/pci/Makefile | 1 + drivers/pci/bus.c | 2 + drivers/pci/of.c | 81 +++++++++++++++- drivers/pci/of_property.c | 194 ++++++++++++++++++++++++++++++++++++++ drivers/pci/pci.h | 19 ++++ drivers/pci/remove.c | 1 + 7 files changed, 309 insertions(+), 1 deletion(-) create mode 100644 drivers/pci/of_property.c
drivers/pci/Kconfig +12 -0
@@ -193,6 +193,18 @@ config PCI_HYPERV The PCI device frontend driver allows the kernel to import arbitrary PCI devices from a PCI backend to support PCI driver domains. +config PCI_DYNAMIC_OF_NODES + bool "Create Devicetree nodes for PCI devices" + depends on OF + select OF_DYNAMIC + help + This option enables support for generating device tree nodes for some + PCI devices. Thus, the driver of this kind can load and overlay + flattened device tree for its downstream devices. + + Once this option is selected, the device tree nodes will be generated + for all PCI bridges. + choice prompt "PCI Express hierarchy optimization setting" default PCIE_BUS_DEFAULT
drivers/pci/Makefile +1 -0
@@ -32,6 +32,7 @@ obj-$(CONFIG_PCI_P2PDMA) += p2pdma.o obj-$(CONFIG_XEN_PCIDEV_FRONTEND) += xen-pcifront.o obj-$(CONFIG_VGA_ARB) += vgaarb.o obj-$(CONFIG_PCI_DOE) += doe.o +obj-$(CONFIG_PCI_DYNAMIC_OF_NODES) += of_property.o # Endpoint library must be initialized before its users obj-$(CONFIG_PCI_ENDPOINT) += endpoint/
drivers/pci/bus.c +2 -0
@@ -340,6 +340,8 @@ void pci_bus_add_device(struct pci_dev *dev)*/ pcibios_bus_add_device (dev);pci_fixup_device (pci_fixup_final, dev); +if (pci_is_bridge (dev)) +of_pci_make_dev_node (dev);pci_create_sysfs_dev_files (dev);pci_proc_attach_device (dev);pci_bridge_d3_update (dev);
drivers/pci/of.c +80 -1
94 lines not on this page · raw message
drivers/pci/of_property.c new file +194 -0
194 lines not on this page · raw message
drivers/pci/pci.h +19 -0
@@ -678,6 +678,25 @@ static inline int devm_of_pci_bridge_init(struct device *dev, struct pci_host_br#endif /* CONFIG_OF */ +struct of_changeset ; + +#ifdef CONFIG_PCI_DYNAMIC_OF_NODES +void of_pci_make_dev_node (struct pci_dev *pdev); +void of_pci_remove_node (struct pci_dev *pdev); +int of_pci_add_properties (struct pci_dev *pdev,struct of_changeset *ocs, +struct device_node *np); +#else +static inline void +of_pci_make_dev_node (struct pci_dev *pdev) +{ +} + +static inline void +of_pci_remove_node (struct pci_dev *pdev) +{ +} +#endif /* CONFIG_PCI_DYNAMIC_OF_NODES */ +#ifdef CONFIG_PCIEAER void pci_no_aer (void );void pci_aer_init (struct pci_dev *dev);
drivers/pci/remove.c +1 -0
@@ -22,6 +22,7 @@ static void pci_stop_dev(struct pci_dev *dev)device_release_driver (&dev->dev);pci_proc_detach_device (dev);pci_remove_sysfs_dev_files (dev); +of_pci_remove_node (dev);pci_dev_assign_added (dev, false); }
Signature · 1 line
2.34.1
Re: [PATCH V9 2/5] PCI: Create device tree node for selected devices
In subject, IIUC this patch does not actually create device tree nodes for selected devices. It looks like it:
- Adds an of_pci_make_dev_node() *interface* that can be used to create this node
- Creates such a node for *every* bridge
- Does nothing at all for "selected devices" or the Xilinx Alveo
Quoted 10 lines · Lizhi Hou
The PCI endpoint device such as Xilinx Alveo PCI card maps the register spaces from multiple hardware peripherals to its PCI BAR. Normally, the PCI core discovers devices and BARs using the PCI enumeration process. There is no infrastructure to discover the hardware peripherals that are present in a PCI device, and which can be accessed through the PCI BARs.
For Alveo PCI card, the card firmware provides a flattened device tree to describe the hardware peripherals on its BARs. The Alveo card driver can load this flattened device tree and leverage device tree framework to generate platform devices for the hardware peripherals eventually.
The Alveo details are relevant to the quirk patch but not to *this* patch.
But the reason for creating a node for every bridge device *is* relevant and should be included here, since that change affects everybody that uses OF.
Quoted 5 lines
Apparently, the device tree framework requires a device tree node for the PCI device. Thus, it can generate the device tree nodes for hardware peripherals underneath. Because PCI is self discoverable bus, there might not be a device tree node created for PCI devices. This patch is to add support to generate device tree node for PCI devices.
s/This patch is to add/Add/
Quoted 2 lines
Added a kernel option. When the option is turned on, the kernel will generate device tree nodes for PCI bridges unconditionally.
s/Added a kernel option/Add a PCI_DYNAMIC_OF_NODES config option/ (Be specific, and way what the patch does, not what you did.)
Quoted 2 lines
Initially, the basic properties are added for the dynamically generated device tree nodes.
Make this specific, e.g., list the specific properties added.
drivers/pci/Kconfig config PCI_HYPERV · line 206
Quoted 11 lines
drivers/pci/Kconfig +11
-0+config PCI_DYNAMIC_OF_NODES + bool "Create Devicetree nodes for PCI devices" + depends on OF + select OF_DYNAMIC + help + This option enables support for generating device tree nodes for some + PCI devices. Thus, the driver of this kind can load and overlay + flattened device tree for its downstream devices. + + Once this option is selected, the device tree nodes will be generated + for all PCI bridges.
Is there a convention for using "devicetree" vs "device tree"? The help message uses both and it would be nice to only use one or the other.
drivers/pci/of.c static int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args * · line 504
Quoted 6 lines
drivers/pci/of.c +1
-1@@ -501,8 +501,10 @@ static int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args ** to rely on this function (you ship a firmware that doesn't * create device nodes for all PCI devices). */ -if (ppnode) +if (ppnode &&of_property_present (ppnode,"interrupt-map" ))
Maybe this deserves a comment? The connection between "interrupt-map" and the rest of this patch isn't obvious to me.
Also, it looks like this happens for *everybody*, regardless of PCI_DYNAMIC_OF_NODES, which seems a little suspect. If it's an unrelated bug fix it should be a different patch.
Quoted 19 lines
drivers/pci/of.c +17
-0break ; + else + ppnode =NULL ; +void of_pci_make_dev_node (struct pci_dev *pdev) +{ +struct device_node *ppnode, *np =NULL ; +const char *pci_type ="dev" ; +struct of_changeset *cset; +const char *name; +int ret; + +/* +* If there is already a device tree node linked to this device, +* return immediately. +*/ +if (pci_device_to_OF_node (pdev)) +return ; +
drivers/pci/of.c int devm_of_pci_bridge_init(struct device *dev, struct pci_host_bridge *bridge) · line 662
Quoted 10 lines
drivers/pci/of.c +10
-0+/* Check if there is device tree node for parent device */ +if (!pdev->bus->self) + ppnode = pdev->bus->dev.of_node; +else + ppnode = pdev->bus->self->dev.of_node; +if (!ppnode) +return ; + +if (pci_is_bridge (pdev)) + pci_type ="pci" ;
Initialize pci_type = "dev" here instead of way up top:
if (pci_is_bridge(pdev))
pci_type = "pci";
else
pci_type = "dev";Quoted 15 lines
drivers/pci/of_property.c new file +14
-0+ name =kasprintf (GFP_KERNEL ,"%s@%x,%x" , pci_type, +PCI_SLOT (pdev->devfn),PCI_FUNC (pdev->devfn)); +static int of_pci_prop_ranges (struct pci_dev *pdev,struct of_changeset *ocs, +struct device_node *np) +{ +struct of_pci_range *rp; +struct resource *res; +int i =0 , j, ret; +u32 flags, num; +u64 val64; + +if (pci_is_bridge (pdev)) { + num =PCI_BRIDGE_RESOURCE_NUM ; + res = &pdev->resource[PCI_BRIDGE_RESOURCES ];
drivers/pci/of_property.c line 102
Quoted 10 lines
drivers/pci/of_property.c new file +10
-0+ }else { + num =PCI_STD_NUM_BARS ; + res = &pdev->resource[PCI_STD_RESOURCES ]; + } + + rp =kcalloc (num,sizeof (*rp),GFP_KERNEL ); +if (!rp) +return -ENOMEM ; + +for (j =0 ; j < num; j++) {
Initialize i = 0 here so it's connected with the use:
for (i = 0, j = 0; j < num; ...)
Quoted 6 lines
drivers/pci/of_property.c new file +6
-0+if (!resource_size (&res[j])) +continue ; + +if (of_pci_get_addr_flags (&res[j], &flags)) +continue ; +
drivers/pci/of_property.c line 118
Quoted 10 lines
drivers/pci/of_property.c new file +10
-0+ val64 = res[j].start; +of_pci_set_address (pdev, rp[i].parent_addr, val64,0 , flags, + false); +if (pci_is_bridge (pdev)) { +memcpy (rp[i].child_addr, rp[i].parent_addr, +sizeof (rp[i].child_addr)); + }else { +/* +* For endpoint device, the lower 64-bits of child +* address is always zero.
For the non-OF folks (like me), can you say what the semantics of parent_addr vs child_addr are? I suppose maybe parent_addr is an address on the primary side of a bridge and child_addr is the corresponding address on the secondary side?
And PCI bridges don't perform address translation, so they are identical?
Quoted 16 lines
drivers/pci/of_property.c new file +15
-0+*/ + rp[i].child_addr[0 ] = j; + } +int of_pci_add_properties (struct pci_dev *pdev,struct of_changeset *ocs, +struct device_node *np) +{ +int ret =0 ; + +if (pci_is_bridge (pdev)) { + ret |=of_changeset_add_prop_string (ocs, np,"device_type" , +"pci" ); + } + + ret |=of_pci_prop_ranges (pdev, ocs, np); + ret |= of_changeset_add_prop_u32(ocs, np, "#address-cells",
drivers/pci/of_property.c line 192
Quoted 10 lines
drivers/pci/of_property.c new file +10
-0+ OF_PCI_ADDRESS_CELLS); + ret |=of_changeset_add_prop_u32 (ocs, np,"#size-cells" , +OF_PCI_SIZE_CELLS ); + ret |=of_pci_prop_reg (pdev, ocs, np); + ret |=of_pci_prop_compatible (pdev, ocs, np); + +/* +* The added properties will be released when the +* changeset is destroyed. +*/
I don't think it's meaningful to OR together the "negative error values" returned by all these functions. Presumably those are things like -EINVAL, -ENOMEM, etc. ORing them together is admittedly non-zero, but yields nonsense.
drivers/pci/pci.h static inline int devm_of_pci_bridge_init(struct device *dev, struct pci_host_br · line 697
Quoted 11 lines
drivers/pci/pci.h +10
-0+return ret; +static inline void +of_pci_make_dev_node (struct pci_dev *pdev) +{ +} + +static inline void +of_pci_remove_node (struct pci_dev *pdev) +{ +}
Pull these functions all onto one line, like other similar stubs in this file.
Quoted 1 line
+#endif /*
CONFIG_PCI_DYNAMIC_OF_NODES*/
Unnecessary comment since this is all 10 lines.
Bjorn Helgaas
Acked-byRe: [PATCH V9 2/5] PCI: Create device tree node for selected devices
Quoted 9 lines · Bjorn Helgaas
In subject, IIUC this patch does not actually create device tree nodes for selected devices. It looks like it:
- Adds an
of_pci_make_dev_node()*interface* that can be used to create this node- Creates such a node for *every* bridge
- Does nothing at all for "selected devices" or the Xilinx Alveo
I forgot: with these comments addressed:
Quoted 210 lines · Lizhi Hou
Quoted 10 lines
The PCI endpoint device such as Xilinx Alveo PCI card maps the register spaces from multiple hardware peripherals to its PCI BAR. Normally, the PCI core discovers devices and BARs using the PCI enumeration process. There is no infrastructure to discover the hardware peripherals that are present in a PCI device, and which can be accessed through the PCI BARs.
For Alveo PCI card, the card firmware provides a flattened device tree to describe the hardware peripherals on its BARs. The Alveo card driver can load this flattened device tree and leverage device tree framework to generate platform devices for the hardware peripherals eventually.
The Alveo details are relevant to the quirk patch but not to *this* patch.
But the reason for creating a node for every bridge device *is* relevant and should be included here, since that change affects everybody that uses OF.
Quoted 5 lines
Apparently, the device tree framework requires a device tree node for the PCI device. Thus, it can generate the device tree nodes for hardware peripherals underneath. Because PCI is self discoverable bus, there might not be a device tree node created for PCI devices. This patch is to add support to generate device tree node for PCI devices.
s/This patch is to add/Add/
Quoted 2 lines
Added a kernel option. When the option is turned on, the kernel will generate device tree nodes for PCI bridges unconditionally.
s/Added a kernel option/Add a
PCI_DYNAMIC_OF_NODESconfig option/ (Be specific, and way what the patch does, not what you did.)Quoted 2 lines
Initially, the basic properties are added for the dynamically generated device tree nodes.
Make this specific, e.g., list the specific properties added.
drivers/pci/Kconfig config PCI_HYPERV · line 206
Quoted 11 lines
drivers/pci/Kconfig +11
-0+config PCI_DYNAMIC_OF_NODES + bool "Create Devicetree nodes for PCI devices" + depends on OF + select OF_DYNAMIC + help + This option enables support for generating device tree nodes for some + PCI devices. Thus, the driver of this kind can load and overlay + flattened device tree for its downstream devices. + + Once this option is selected, the device tree nodes will be generated + for all PCI bridges.Is there a convention for using "devicetree" vs "device tree"? The help message uses both and it would be nice to only use one or the other.
drivers/pci/of.c static int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args * · line 504
Quoted 6 lines
drivers/pci/of.c +1
-1@@ -501,8 +501,10 @@ static int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args ** to rely on this function (you ship a firmware that doesn't * create device nodes for all PCI devices). */ -if (ppnode) +if (ppnode &&of_property_present (ppnode,"interrupt-map" ))Maybe this deserves a comment? The connection between "interrupt-map" and the rest of this patch isn't obvious to me.
Also, it looks like this happens for *everybody*, regardless of
PCI_DYNAMIC_OF_NODES, which seems a little suspect. If it's an unrelated bug fix it should be a different patch.Quoted 19 lines
drivers/pci/of.c +17
-0break ; + else + ppnode =NULL ; +void of_pci_make_dev_node (struct pci_dev *pdev) +{ +struct device_node *ppnode, *np =NULL ; +const char *pci_type ="dev" ; +struct of_changeset *cset; +const char *name; +int ret; + +/* +* If there is already a device tree node linked to this device, +* return immediately. +*/ +if (pci_device_to_OF_node (pdev)) +return ; +drivers/pci/of.c int devm_of_pci_bridge_init(struct device *dev, struct pci_host_bridge *bridge) · line 662
Quoted 10 lines
drivers/pci/of.c +10
-0+/* Check if there is device tree node for parent device */ +if (!pdev->bus->self) + ppnode = pdev->bus->dev.of_node; +else + ppnode = pdev->bus->self->dev.of_node; +if (!ppnode) +return ; + +if (pci_is_bridge (pdev)) + pci_type ="pci" ;Initialize
pci_type= "dev" here instead of way up top:if (pci_is_bridge(pdev)) pci_type = "pci"; else pci_type = "dev";Quoted 15 lines
drivers/pci/of_property.c new file +14
-0+ name =kasprintf (GFP_KERNEL ,"%s@%x,%x" , pci_type, +PCI_SLOT (pdev->devfn),PCI_FUNC (pdev->devfn)); +static int of_pci_prop_ranges (struct pci_dev *pdev,struct of_changeset *ocs, +struct device_node *np) +{ +struct of_pci_range *rp; +struct resource *res; +int i =0 , j, ret; +u32 flags, num; +u64 val64; + +if (pci_is_bridge (pdev)) { + num =PCI_BRIDGE_RESOURCE_NUM ; + res = &pdev->resource[PCI_BRIDGE_RESOURCES ];drivers/pci/of_property.c line 102
Quoted 10 lines
drivers/pci/of_property.c new file +10
-0+ }else { + num =PCI_STD_NUM_BARS ; + res = &pdev->resource[PCI_STD_RESOURCES ]; + } + + rp =kcalloc (num,sizeof (*rp),GFP_KERNEL ); +if (!rp) +return -ENOMEM ; + +for (j =0 ; j < num; j++) {Initialize i = 0 here so it's connected with the use:
for (i = 0, j = 0; j < num; ...)
Quoted 6 lines
drivers/pci/of_property.c new file +6
-0+if (!resource_size (&res[j])) +continue ; + +if (of_pci_get_addr_flags (&res[j], &flags)) +continue ; +drivers/pci/of_property.c line 118
Quoted 10 lines
drivers/pci/of_property.c new file +10
-0+ val64 = res[j].start; +of_pci_set_address (pdev, rp[i].parent_addr, val64,0 , flags, + false); +if (pci_is_bridge (pdev)) { +memcpy (rp[i].child_addr, rp[i].parent_addr, +sizeof (rp[i].child_addr)); + }else { +/* +* For endpoint device, the lower 64-bits of child +* address is always zero. For the non-OF folks (like me), can you say what the semantics of
parent_addrvschild_addrare? I suppose maybeparent_addris an address on the primary side of a bridge andchild_addris the corresponding address on the secondary side?And PCI bridges don't perform address translation, so they are identical?
Quoted 16 lines
drivers/pci/of_property.c new file +15
-0+*/ + rp[i].child_addr[0 ] = j; + } +int of_pci_add_properties (struct pci_dev *pdev,struct of_changeset *ocs, +struct device_node *np) +{ +int ret =0 ; + +if (pci_is_bridge (pdev)) { + ret |=of_changeset_add_prop_string (ocs, np,"device_type" , +"pci" ); + } + + ret |=of_pci_prop_ranges (pdev, ocs, np); + ret |= of_changeset_add_prop_u32(ocs, np, "#address-cells",drivers/pci/of_property.c line 192
Quoted 10 lines
drivers/pci/of_property.c new file +10
-0+ OF_PCI_ADDRESS_CELLS); + ret |=of_changeset_add_prop_u32 (ocs, np,"#size-cells" , +OF_PCI_SIZE_CELLS ); + ret |=of_pci_prop_reg (pdev, ocs, np); + ret |=of_pci_prop_compatible (pdev, ocs, np); + +/* +* The added properties will be released when the +* changeset is destroyed. +*/ I don't think it's meaningful to OR together the "negative error values" returned by all these functions. Presumably those are things like
-EINVAL,-ENOMEM, etc. ORing them together is admittedly non-zero, but yields nonsense.drivers/pci/pci.h static inline int devm_of_pci_bridge_init(struct device *dev, struct pci_host_br · line 697
Quoted 11 lines
drivers/pci/pci.h +10
-0+return ret; +static inline void +of_pci_make_dev_node (struct pci_dev *pdev) +{ +} + +static inline void +of_pci_remove_node (struct pci_dev *pdev) +{ +}Pull these functions all onto one line, like other similar stubs in this file.
Quoted 1 line
+#endif /*
CONFIG_PCI_DYNAMIC_OF_NODES*/Unnecessary comment since this is all 10 lines.
Re: [PATCH V9 2/5] PCI: Create device tree node for selected devices
In reply to Bjorn HelgaasQuoted 35 lines · Bjorn Helgaas
In subject, IIUC this patch does not actually create device tree nodes for selected devices. It looks like it:
- Adds an
of_pci_make_dev_node()*interface* that can be used to create this node- Creates such a node for *every* bridge
- Does nothing at all for "selected devices" or the Xilinx Alveo
Quoted 10 lines · Lizhi Hou
The PCI endpoint device such as Xilinx Alveo PCI card maps the register spaces from multiple hardware peripherals to its PCI BAR. Normally, the PCI core discovers devices and BARs using the PCI enumeration process. There is no infrastructure to discover the hardware peripherals that are present in a PCI device, and which can be accessed through the PCI BARs.
For Alveo PCI card, the card firmware provides a flattened device tree to describe the hardware peripherals on its BARs. The Alveo card driver can load this flattened device tree and leverage device tree framework to generate platform devices for the hardware peripherals eventually.
The Alveo details are relevant to the quirk patch but not to *this* patch.
But the reason for creating a node for every bridge device *is* relevant and should be included here, since that change affects everybody that uses OF.
Quoted 5 lines
Apparently, the device tree framework requires a device tree node for the PCI device. Thus, it can generate the device tree nodes for hardware peripherals underneath. Because PCI is self discoverable bus, there might not be a device tree node created for PCI devices. This patch is to add support to generate device tree node for PCI devices.
s/This patch is to add/Add/
Quoted 8 lines
Quoted 2 lines
Added a kernel option. When the option is turned on, the kernel will generate device tree nodes for PCI bridges unconditionally.
s/Added a kernel option/Add a
PCI_DYNAMIC_OF_NODESconfig option/ (Be specific, and way what the patch does, not what you did.)Quoted 2 lines
Initially, the basic properties are added for the dynamically generated device tree nodes.
Make this specific, e.g., list the specific properties added.
I rewrote the description as below. Does it look better?
PCI: Create device tree node for bridge
The PCI endpoint device such as Xilinx Alveo PCI card maps the register spaces from multiple hardware peripherals to its PCI BAR. Normally, the PCI core discovers devices and BARs using the PCI enumeration process. There is no infrastructure to discover the hardware peripherals that are present in a PCI device, and which can be accessed through the PCI BARs.
Apparently, the device tree framework requires a device tree node for the PCI device. Thus, it can generate the device tree nodes for hardware peripherals underneath. Because PCI is self discoverable bus, there might not be a device tree node created for PCI devices. Furthermore, if the PCI device is hot pluggable, when it is plugged in, the device tree nodes for its parent bridges are required. Add support to generate device tree node for PCI bridges.
Added an of_pci_make_dev_node() interface that can be used to create device tree node for PCI devices.
Added a PCI_DYNAMIC_OF_NODES config option. When the option is turned on, the kernel will generate device tree nodes for PCI bridges unconditionally.
Initially, the basic properties are added for the dynamically generated device tree nodes which include #address-cells, #size-cells, device_type, compatible, ranges, reg.
Quoted 15 lines
drivers/pci/Kconfig config PCI_HYPERV · line 206
Quoted 12 lines
drivers/pci/Kconfig +11
-0+config PCI_DYNAMIC_OF_NODES + bool "Create Devicetree nodes for PCI devices" + depends on OF + select OF_DYNAMIC + help + This option enables support for generating device tree nodes for some + PCI devices. Thus, the driver of this kind can load and overlay + flattened device tree for its downstream devices. + + Once this option is selected, the device tree nodes will be generated + for all PCI bridges.Is there a convention for using "devicetree" vs "device tree"? The help message uses both and it would be nice to only use one or the other.
Ok. Will use "device tree".
Quoted 10 lines
drivers/pci/of.c static int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args * · line 504
Quoted 7 lines
drivers/pci/of.c +1
-1@@ -501,8 +501,10 @@ static int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args ** to rely on this function (you ship a firmware that doesn't * create device nodes for all PCI devices). */ -if (ppnode) +if (ppnode &&of_property_present (ppnode,"interrupt-map" ))Maybe this deserves a comment? The connection between "interrupt-map" and the rest of this patch isn't obvious to me.
Quoted 3 lines
Also, it looks like this happens for *everybody*, regardless of
PCI_DYNAMIC_OF_NODES, which seems a little suspect. If it's an unrelated bug fix it should be a different patch.
This is not a bug fix. The check will distinguish between device tree nodes automatically created for pci bridges by this patch with those created by a DT based system. With this patch, device tree nodes are created for pci bridges, thus ppnode here will be non-zero and we will break out of the loop. In order to still use pci_swizzle_interrupt_pin(), checking “interrupt-map” for ppnode is added here.
After thinking about this more, using “interrupt-map” property may not be correct for the cases where ppnode is not dynamically generated and it does not have “interrupt-map”. So, I would introduce a new property “dynamic” for pci bridge nodes generated dynamically. And change the code to: if (ppnode && of_property_present(ppnode, "dynamic")).
Does this make sense?
Quoted 31 lines
Quoted 19 lines
drivers/pci/of.c +17
-0break ; + else + ppnode =NULL ; +void of_pci_make_dev_node (struct pci_dev *pdev) +{ +struct device_node *ppnode, *np =NULL ; +const char *pci_type ="dev" ; +struct of_changeset *cset; +const char *name; +int ret; + +/* +* If there is already a device tree node linked to this device, +* return immediately. +*/ +if (pci_device_to_OF_node (pdev)) +return ; +drivers/pci/of.c int devm_of_pci_bridge_init(struct device *dev, struct pci_host_bridge *bridge) · line 662
Quoted 10 lines
drivers/pci/of.c +10
-0+/* Check if there is device tree node for parent device */ +if (!pdev->bus->self) + ppnode = pdev->bus->dev.of_node; +else + ppnode = pdev->bus->self->dev.of_node; +if (!ppnode) +return ; + +if (pci_is_bridge (pdev)) + pci_type ="pci" ;Initialize
pci_type= "dev" here instead of way up top:
Quoted 4 lines
if (pci_is_bridge(pdev))
pci_type = "pci";
else
pci_type = "dev";sure.
Quoted 27 lines
Quoted 15 lines
drivers/pci/of_property.c new file +14
-0+ name =kasprintf (GFP_KERNEL ,"%s@%x,%x" , pci_type, +PCI_SLOT (pdev->devfn),PCI_FUNC (pdev->devfn)); +static int of_pci_prop_ranges (struct pci_dev *pdev,struct of_changeset *ocs, +struct device_node *np) +{ +struct of_pci_range *rp; +struct resource *res; +int i =0 , j, ret; +u32 flags, num; +u64 val64; + +if (pci_is_bridge (pdev)) { + num =PCI_BRIDGE_RESOURCE_NUM ; + res = &pdev->resource[PCI_BRIDGE_RESOURCES ];drivers/pci/of_property.c line 102
Quoted 10 lines
drivers/pci/of_property.c new file +10
-0+ }else { + num =PCI_STD_NUM_BARS ; + res = &pdev->resource[PCI_STD_RESOURCES ]; + } + + rp =kcalloc (num,sizeof (*rp),GFP_KERNEL ); +if (!rp) +return -ENOMEM ; + +for (j =0 ; j < num; j++) {Initialize i = 0 here so it's connected with the use:
Quoted 1 line
for (i = 0, j = 0; j < num; ...)
ok.
Quoted 22 lines
Quoted 7 lines
drivers/pci/of_property.c new file +6
-0+if (!resource_size (&res[j])) +continue ; + +if (of_pci_get_addr_flags (&res[j], &flags)) +continue ; +drivers/pci/of_property.c line 118
Quoted 10 lines
drivers/pci/of_property.c new file +10
-0+ val64 = res[j].start; +of_pci_set_address (pdev, rp[i].parent_addr, val64,0 , flags, + false); +if (pci_is_bridge (pdev)) { +memcpy (rp[i].child_addr, rp[i].parent_addr, +sizeof (rp[i].child_addr)); + }else { +/* +* For endpoint device, the lower 64-bits of child +* address is always zero. For the non-OF folks (like me), can you say what the semantics of
parent_addrvschild_addrare? I suppose maybeparent_addris an address on the primary side of a bridge andchild_addris the corresponding address on the secondary side?
Quoted 2 lines
And PCI bridges don't perform address translation, so they are identical?
I will add more comments here.
Quoted 22 lines
Quoted 22 lines
drivers/pci/of_property.c new file +21
-0+*/ + rp[i].child_addr[0 ] = j; + } +int of_pci_add_properties (struct pci_dev *pdev,struct of_changeset *ocs, +struct device_node *np) +{ +int ret =0 ; + +if (pci_is_bridge (pdev)) { + ret |=of_changeset_add_prop_string (ocs, np,"device_type" , +"pci" ); + } + + ret |=of_pci_prop_ranges (pdev, ocs, np); + ret |=of_changeset_add_prop_u32 (ocs, np,"#address-cells" , +OF_PCI_ADDRESS_CELLS ); + ret |=of_changeset_add_prop_u32 (ocs, np,"#size-cells" , +OF_PCI_SIZE_CELLS ); + ret |=of_pci_prop_reg (pdev, ocs, np); + ret |=of_pci_prop_compatible (pdev, ocs, np); +
Quoted 8 lines
drivers/pci/of_property.c line 192
Quoted 4 lines
drivers/pci/of_property.c new file +4
-0+/* +* The added properties will be released when the +* changeset is destroyed. +*/ I don't think it's meaningful to OR together the "negative error values" returned by all these functions. Presumably those are things like
-EINVAL,-ENOMEM, etc. ORing them together is admittedly non-zero, but yields nonsense.
ok. I will return for each failure.
Quoted 13 lines
drivers/pci/pci.h static inline int devm_of_pci_bridge_init(struct device *dev, struct pci_host_br · line 697
Quoted 11 lines
drivers/pci/pci.h +10
-0+return ret; +static inline void +of_pci_make_dev_node (struct pci_dev *pdev) +{ +} + +static inline void +of_pci_remove_node (struct pci_dev *pdev) +{ +}Pull these functions all onto one line, like other similar stubs in this file.
Sure.
Quoted 3 lines
Quoted 2 lines
+#endif /*
CONFIG_PCI_DYNAMIC_OF_NODES*/Unnecessary comment since this is all 10 lines.
Will remove it.
Thanks,
Lizhi
Re: [PATCH V9 2/5] PCI: Create device tree node for selected devices
Quoted 10 lines · Lizhi Hou
On 6/21/23 13:22, Bjorn Helgaas wrote:
Added an
of_pci_make_dev_node()interface that can be used to create device tree node for PCI devices.Added a
PCI_DYNAMIC_OF_NODESconfig option. When the option is turned on,
the kernel will generate device tree nodes for PCI bridges unconditionally.
Quoted 4 lines
Initially, the basic properties are added for the dynamically generated device tree nodes which include #address-cells, #size-cells,
device_type,
compatible, ranges, reg.
s/Added/Add/ (twice, mentioned before).
The commit log should say what the *patch* does, not what *you* did.
Quoted 21 lines
Quoted 10 lines
drivers/pci/of.c static int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args * · line 504
Quoted 6 lines
drivers/pci/of.c +1
-1@@ -501,8 +501,10 @@ static int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args ** to rely on this function (you ship a firmware that doesn't * create device nodes for all PCI devices). */ -if (ppnode) +if (ppnode &&of_property_present (ppnode,"interrupt-map" ))Maybe this deserves a comment? The connection between "interrupt-map" and the rest of this patch isn't obvious to me.
Quoted 3 lines
Also, it looks like this happens for *everybody*, regardless of
PCI_DYNAMIC_OF_NODES, which seems a little suspect. If it's an unrelated bug fix it should be a different patch.This is not a bug fix. The check will distinguish between device tree nodes automatically created for pci bridges by this patch with those created by a DT based system. With this patch, device tree nodes are created for pci bridges, thus ppnode here will be non-zero and we will break out of the loop. In order to still use
pci_swizzle_interrupt_pin(), checking “interrupt-map” for ppnode is added here.
Quoted 7 lines
After thinking about this more, using “interrupt-map” property may not be correct for the cases where ppnode is not dynamically generated and it does not have “interrupt-map”. So, I would introduce a new property “dynamic” for pci bridge nodes generated dynamically. And change the code to: if (ppnode &&
of_property_present(ppnode, "dynamic")).Does this make sense?
Makes a lot more sense to me than relying on some unrelated and undocumented property. Probably still would benefit from an #ifdef.
Rob might have an opinion on whether "dynamic" makes sense from a DT perspective.
Bjorn
PATCH v9 3/5 PCI: Add PCI quirks to generate device tree node for Xilinx Alveo U50
In reply to Lizhi HouThe Xilinx Alveo U50 PCI card exposes multiple hardware peripherals on its PCI BAR. The card firmware provides a flattened device tree to describe the hardware peripherals on its BARs. This allows U50 driver to load the flattened device tree and generate the device tree node for hardware peripherals underneath.
To generate device tree node for U50 card, added PCI quirks to call of_pci_make_dev_node() for U50.
--- drivers/pci/quirks.c | 11 +++++++++++ 1 file changed, 11 insertions(+)
drivers/pci/quirks.c +11 -0
@@ -6041,3 +6041,14 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2d, dpc_log_size);DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_INTEL ,0x9a2f , dpc_log_size);DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_INTEL ,0x9a31 , dpc_log_size);#endif + +/* +* For PCI device which have multiple downstream devices, its driver may use +* a flattened device tree to describe the downstream devices. +* To overlay the flattened device tree, the PCI device and all its ancestor +* devices need to have device tree nodes on system base device tree. Thus, +* before driver probing, it might need to add a device tree node as the final +* fixup. +*/ +DECLARE_PCI_FIXUP_FINAL (PCI_VENDOR_ID_XILINX ,0x5020 , of_pci_make_dev_node); +DECLARE_PCI_FIXUP_FINAL (PCI_VENDOR_ID_XILINX ,0x5021 , of_pci_make_dev_node);
Signature · 1 line
2.34.1
Re: [PATCH V9 3/5] PCI: Add PCI quirks to generate device tree node for Xilinx Alveo U50
In subject, s/Add PCI/Add/ (no need to repeat "PCI")
Quoted 8 lines · Lizhi Hou
The Xilinx Alveo U50 PCI card exposes multiple hardware peripherals on its PCI BAR. The card firmware provides a flattened device tree to describe the hardware peripherals on its BARs. This allows U50 driver to load the flattened device tree and generate the device tree node for hardware peripherals underneath.
To generate device tree node for U50 card, added PCI quirks to call
of_pci_make_dev_node()for U50.
s/added/add/ (tell me what the patch does, not what you did)
Quoted 1 line
Signed-off-by Lizhi Hou <[email protected]>
Quoted 9 lines
--- drivers/pci/quirks.c | 11 +++++++++++ 1 file changed, 11 insertions(+)drivers/pci/quirks.c +0
-0
drivers/pci/quirks.c DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2d, dpc_log_size); · line 6050
Quoted 10 lines
drivers/pci/quirks.c +7
-0@@ -6041,3 +6041,14 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2d, dpc_log_size);DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_INTEL ,0x9a2f , dpc_log_size);DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_INTEL ,0x9a31 , dpc_log_size);#endif + +/* +* For PCI device which have multiple downstream devices, its driver may use +* a flattened device tree to describe the downstream devices. +* To overlay the flattened device tree, the PCI device and all its ancestor +* devices need to have device tree nodes on system base device tree. Thus, +* before driver probing, it might need to add a device tree node as the final
s/For PCI device which have multiple/For a PCI device with multiple/
It looks like you intend two separate paragraphs in the comment. If so, add a blank line between them. If not, rewrap so they're a single paragraph.
Quoted 7 lines
drivers/pci/quirks.c +4
-0+* fixup. +*/ +DECLARE_PCI_FIXUP_FINAL (PCI_VENDOR_ID_XILINX ,0x5020 , of_pci_make_dev_node); +DECLARE_PCI_FIXUP_FINAL (PCI_VENDOR_ID_XILINX ,0x5021 , of_pci_make_dev_node);Signature · 1 line
2.34.1
PATCH v9 4/5 of: overlay: Extend of_overlay_fdt_apply() to specify the target node
In reply to Lizhi HouCurrently, in an overlay fdt fragment, it needs to specify the exact location in base DT. In another word, when the fdt fragment is generated, the base DT location for the fragment is already known.
There is new use case that the base DT location is unknown when fdt fragment is generated. For example, the add-on device provide a fdt overlay with its firmware to describe its downstream devices. Because it is add-on device which can be plugged to different systems, its firmware will not be able to know the overlay location in base DT. Instead, the device driver will load the overlay fdt and apply it to base DT at runtime. In this case, of_overlay_fdt_apply() needs to be extended to specify the target node for device driver to apply overlay fdt.
int overlay_fdt_apply(..., struct device_node *base);
--- drivers/of/overlay.c | 42 +++++++++++++++++++++++++++++++----------- drivers/of/unittest.c | 3 ++- include/linux/of.h | 2 +- 3 files changed, 34 insertions(+), 13 deletions(-)
drivers/of/overlay.c +31 -11
@@ -682,9 +682,11 @@ static int build_changeset(struct overlay_changeset *ovcs)* 1) "target" property containing the phandle of the target * 2) "target-path" property containing the path of the target */ -static struct device_node *find_target (struct device_node *info_node) +static struct device_node *find_target (struct device_node *info_node, +struct device_node *target_base) {struct device_node *node; +char *target_path;const char *path;u32 val;int ret;
@@ -700,10 +702,23 @@ static struct device_node *find_target(struct device_node *info_node) ret =of_property_read_string (info_node,"target-path" , &path);if (!ret) { - node =of_find_node_by_path (path); -if (!node) -pr_err ("find target, node: %pOF, path '%s' not found\n" , - info_node, path); +if (target_base) { + target_path =kasprintf (GFP_KERNEL ,"%pOF%s" , target_base, path); +if (!target_path) +return NULL ; + node =of_find_node_by_path (target_path); +if (!node) { +pr_err ("find target, node: %pOF, path '%s' not found\n" , + info_node, target_path); + } +kfree (target_path); + }else { + node =of_find_node_by_path (path); +if (!node) { +pr_err ("find target, node: %pOF, path '%s' not found\n" , + info_node, path); + } + }return node; }
@@ -715,6 +730,7 @@ static struct device_node *find_target(struct device_node *info_node)/** * init_overlay_changeset() - initialize overlay changeset from overlay tree * @ovcs: Overlay changeset to build +* @target_base: Point to the target node to apply overlay * * Initialize @ovcs. Populate @ovcs->fragments with node information from * the top level of @overlay_root. The relevant top level nodes are the
@@ -725,7 +741,8 @@ static struct device_node *find_target(struct device_node *info_node)* detected in @overlay_root. On error return, the caller of * init_overlay_changeset() must call free_overlay_changeset(). */ -static int init_overlay_changeset (struct overlay_changeset *ovcs) +static int init_overlay_changeset (struct overlay_changeset *ovcs, +struct device_node *target_base) {struct device_node *node, *overlay_node;struct fragment *fragment;
@@ -786,7 +803,7 @@ static int init_overlay_changeset(struct overlay_changeset *ovcs) fragment = &fragments[cnt]; fragment->overlay = overlay_node; - fragment->target =find_target (node); + fragment->target =find_target (node, target_base);if (!fragment->target) {of_node_put (fragment->overlay); ret = -EINVAL ;
@@ -877,6 +894,7 @@ static void free_overlay_changeset(struct overlay_changeset *ovcs)* * of_overlay_apply() - Create and apply an overlay changeset * @ovcs: overlay changeset +* @base: point to the target node to apply overlay * * Creates and applies an overlay changeset. *
@@ -900,7 +918,8 @@ static void free_overlay_changeset(struct overlay_changeset *ovcs)* the caller of of_overlay_apply() must call free_overlay_changeset(). */ -static int of_overlay_apply (struct overlay_changeset *ovcs) +static int of_overlay_apply (struct overlay_changeset *ovcs, +struct device_node *base) {int ret =0 , ret_revert, ret_tmp;
@@ -908,7 +927,7 @@ static int of_overlay_apply(struct overlay_changeset *ovcs)if (ret) goto out; - ret =init_overlay_changeset (ovcs); + ret =init_overlay_changeset (ovcs, base);if (ret) goto out;
@@ -952,6 +971,7 @@ static int of_overlay_apply(struct overlay_changeset *ovcs)* @overlay_fdt: pointer to overlay FDT * @overlay_fdt_size: number of bytes in @overlay_fdt * @ret_ovcs_id: pointer for returning created changeset id +* @base: pointer for the target node to apply overlay * * Creates and applies an overlay changeset. *
@@ -967,7 +987,7 @@ static int of_overlay_apply(struct overlay_changeset *ovcs)*/ int of_overlay_fdt_apply (const void *overlay_fdt,u32 overlay_fdt_size, -int *ret_ovcs_id) +int *ret_ovcs_id,struct device_node *base) {void *new_fdt;void *new_fdt_align;
@@ -1037,7 +1057,7 @@ int of_overlay_fdt_apply(const void *overlay_fdt, u32 overlay_fdt_size, } ovcs->overlay_mem = overlay_mem; - ret =of_overlay_apply (ovcs); + ret =of_overlay_apply (ovcs, base);/* * If of_overlay_apply() error, calling free_overlay_changeset() may * result in a memory leak if the apply partly succeeded, so do NOT
drivers/of/unittest.c +2 -1
@@ -3506,7 +3506,8 @@ static int __init overlay_data_apply(const char *overlay_name, int *ovcs_id)if (!size)pr_err ("no overlay data for %s\n" , overlay_name); - ret =of_overlay_fdt_apply (info->dtbo_begin, size, &info->ovcs_id); + ret =of_overlay_fdt_apply (info->dtbo_begin, size, &info->ovcs_id, +NULL );if (ovcs_id) *ovcs_id = info->ovcs_id;if (ret <0 )
include/linux/of.h +1 -1
@@ -1668,7 +1668,7 @@ struct of_overlay_notify_data {#ifdef CONFIG_OF_OVERLAY int of_overlay_fdt_apply (const void *overlay_fdt,u32 overlay_fdt_size, -int *ovcs_id); +int *ovcs_id,struct device_node *target_base);int of_overlay_remove (int *ovcs_id);int of_overlay_remove_all (void );
Signature · 1 line
2.34.1
PATCH v9 5/5 of: unittest: Add pci_dt_testdrv pci driver
In reply to Lizhi Houpci_dt_testdrv is bound to QEMU PCI Test Device. It reads overlay_pci_node fdt fragment and apply it to Test Device. Then it calls of_platform_default_populate() to populate the platform devices.
--- drivers/of/unittest-data/Makefile | 3 +- .../of/unittest-data/overlay_pci_node.dtso | 22 ++ drivers/of/unittest.c | 188 ++++++++++++++++++ drivers/pci/quirks.c | 1 + 4 files changed, 213 insertions(+), 1 deletion(-) create mode 100644 drivers/of/unittest-data/overlay_pci_node.dtso
drivers/of/unittest-data/Makefile +2 -1
@@ -32,7 +32,8 @@ obj-$(CONFIG_OF_OVERLAY) += overlay.dtbo.o \ overlay_gpio_02b.dtbo.o \ overlay_gpio_03.dtbo.o \ overlay_gpio_04a.dtbo.o \ - overlay_gpio_04b.dtbo.o + overlay_gpio_04b.dtbo.o \ + overlay_pci_node.dtbo.o # enable creation of __symbols__ node DTC_FLAGS_overlay += -@
drivers/of/unittest-data/overlay_pci_node.dtso new file +22 -0
@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; +/ { + fragment@0 { + target-path=""; + __overlay__ { + #address-cells = <3>; + #size-cells = <2>; + pci-ep-bus@0 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x0 0x0 0x1000>; + reg = <0 0 0 0 0>; + unittest-pci@100 { + compatible = "unittest-pci"; + reg = <0x100 0x200>; + }; + }; + }; + }; +};
drivers/of/unittest.c +188 -0
218 lines not on this page · raw message
drivers/pci/quirks.c +1 -0
@@ -6052,3 +6052,4 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a31, dpc_log_size);*/ DECLARE_PCI_FIXUP_FINAL (PCI_VENDOR_ID_XILINX ,0x5020 , of_pci_make_dev_node);DECLARE_PCI_FIXUP_FINAL (PCI_VENDOR_ID_XILINX ,0x5021 , of_pci_make_dev_node); +DECLARE_PCI_FIXUP_FINAL (PCI_VENDOR_ID_REDHAT ,0x0005 , of_pci_make_dev_node);
Signature · 1 line
2.34.1
Re: [PATCH V9 5/5] of: unittest: Add pci_dt_testdrv pci driver
Hi all,
Quoted 5 lines · On Wed, 21 Jun 2023 10:34:09 -0700 Lizhi Hou <[email protected]> wrote:
pci_dt_testdrvis bound to QEMU PCI Test Device. It readsoverlay_pci_nodefdt fragment and apply it to Test Device. Then it callsof_platform_default_populate()to populate the platform devices.
Quoted 8 lines
Signed-off-by Lizhi Hou <[email protected]>--- drivers/of/unittest-data/Makefile | 3 +- .../of/unittest-data/overlay_pci_node.dtso | 22 ++ drivers/of/unittest.c | 188 ++++++++++++++++++ drivers/pci/quirks.c | 1 + 4 files changed, 213 insertions(+), 1 deletion(-) create mode 100644 drivers/of/unittest-data/overlay_pci_node.dtso
Did the test under QEMU with the instructions that Lizhi provided at
https://github.com/houlz0507/xoclv2/blob/pci-dt-0329/pci-dt-patch-0329/README
The unittest results were:
--- 8< ---
[ 1.107378] ### dt-test ### pass of_unittest_lifecycle():3273 [ 1.110068] ### dt-test ### pass of_unittest_pci_node():3909 [ 1.110401] ### dt-test ### pass unittest_pci_probe():3840 [ 1.110618] ### dt-test ### pass of_unittest_pci_node():3914 [ 1.110759] ### dt-test ### pass of_unittest_pci_node_verify():3870 [ 1.110894] ### dt-test ### pass of_unittest_pci_node_verify():3877 [ 1.110985] ### dt-test ### pass of_unittest_pci_node_verify():3884 [ 1.111088] ### dt-test ### pass of_unittest_pci_node():3926 [ 1.111171] ### dt-test ### pass of_unittest_pci_node():3927 [ 1.112056] ### dt-test ### pass of_unittest_pci_node_verify():3870 [ 1.112201] ### dt-test ### pass of_unittest_pci_node_verify():3890 [ 1.112326] ### dt-test ### pass of_unittest_pci_node_verify():3892 [ 1.112489] ### dt-test ### pass of_unittest_check_tree_linkage():271
--- 8< ---
Based on the test provided, no failure detected.
Further more, I dumped the dt (PCI related nodes) available on the target. If someone needs to look at it:
--- 8< ---
# cat /tmp/dt.dts /dts-v1/;
/ {
#address-cells = <0x02>;
#size-cells = <0x02>;
interrupt-parent = <0x8002>;
compatible = "linux,dummy-virt";
name = [00];
[...]
pcie@10000000 {
#address-cells = <0x03>;
dma-coherent;
bus-range = <0x00 0xff>;
interrupt-map = <0x00 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x03 0x04 0x00 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x04 0x04 0x00 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x05 0x04 0x00 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x06 0x04 0x800 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x04 0x04 0x800 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x05 0x04 0x800 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x06 0x04 0x800 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x03 0x04 0x1000 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x05 0x04 0x1000 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x06 0x04 0x1000 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x03 0x04 0x1000 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x04 0x04 0x1800 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x06 0x04 0x1800 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x03 0x04 0x1800 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x04 0x04 0x1800 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x05 0x04>;
#size-cells = <0x02>;
device_type = "pci";
interrupt-map-mask = <0x1800 0x00 0x00 0x07>;
compatible = "pci-host-ecam-generic";
ranges = <0x1000000 0x00 0x00 0x00 0x3eff0000 0x00 0x10000 0x2000000 0x00 0x10000000 0x00 0x10000000 0x00 0x2eff0000 0x3000000 0x80 0x00 0x80 0x00 0x80 0x00>;
#interrupt-cells = <0x01>;
reg = <0x40 0x10000000 0x00 0x10000000>;
linux,pci-domain = <0x00>;
msi-parent = <0x8003>;
name = "pcie";
pci@3,0 {
#address-cells = <0x03>;
#size-cells = <0x02>;
device_type = "pci";
compatible = "pci1b36,c\0pciclass,060400\0pciclass,0604";
ranges = <0x81001800 0x00 0x1000 0x81001800 0x00 0x1000 0x00 0x2000 0x82001800 0x00 0x10000000 0x82001800 0x00 0x10000000 0x00 0x200000 0xc3001800 0x80 0x00 0xc3001800 0x80 0x00 0x00 0x200000>;
reg = <0x1800 0xffff6d76 0xc2b23600 0xffff6d76 0x3fbf63a0>;
pci@0,0 {
#address-cells = <0x03>;
#size-cells = <0x02>;
device_type = "pci";
compatible = "pci104c,8232\0pciclass,060400\0pciclass,0604";
ranges = <0x81010000 0x00 0x1000 0x81010000 0x00 0x1000 0x00 0x1000 0x82010000 0x00 0x10000000 0x82010000 0x00 0x10000000 0x00 0x200000 0xc3010000 0x80 0x00 0xc3010000 0x80 0x00 0x00 0x200000>;
reg = <0x10000 0xffff6d76 0xc2b32580 0xffff6d76 0xc2b1f000>;
pci@0,0 {
#address-cells = <0x03>;
#size-cells = <0x02>;
device_type = "pci";
compatible = "pci104c,8233\0pciclass,060400\0pciclass,0604";
ranges = <0x81020000 0x00 0x1000 0x81020000 0x00 0x1000 0x00 0x1000 0x82020000 0x00 0x10000000 0x82020000 0x00 0x10000000 0x00 0x200000 0xc3020000 0x80 0x00 0xc3020000 0x80 0x00 0x00 0x200000>;
reg = <0x20000 0xffff6d76 0xc2b3f880 0xffff6d76 0xc2b30400>;
dev@0,0 {
#address-cells = <0x03>;
#size-cells = <0x02>;
compatible = "pci1b36,5\0pciclass,00ff00\0pciclass,00ff";
ranges = <0x00 0x00 0x00 0x82030000 0x00 0x10000000 0x00 0x1000 0x01 0x00 0x00 0x81030000 0x00 0x1000 0x00 0x100>;
reg = <0x30000 0xffff6d76 0xc2b42800 0xffff6d76 0xc2b30800>;
};
};
};
};
pci@3,1 {
#address-cells = <0x03>;
#size-cells = <0x02>;
device_type = "pci";
compatible = "pci1b36,c\0pciclass,060400\0pciclass,0604";
ranges = <0x81001900 0x00 0x3000 0x81001900 0x00 0x3000 0x00 0x1000 0x82001900 0x00 0x10200000 0x82001900 0x00 0x10200000 0x00 0x200000 0xc3001900 0x80 0x200000 0xc3001900 0x80 0x200000 0x00 0x200000>;
reg = <0x1900 0xffff6d76 0xc2b29280 0xffff6d76 0x3fbf63a0>;
};
pci@4,0 {
#address-cells = <0x03>;
#size-cells = <0x02>;
device_type = "pci";
compatible = "pci8086,244e\0pciclass,060401\0pciclass,0604";
ranges = <0x82002000 0x00 0x10400000 0x82002000 0x00 0x10400000 0x00 0x100000>;
reg = <0x2000 0xffff6d76 0xc2b32d80 0xffff6d76 0x3fbf63a0>;
pci@0,0 {
#address-cells = <0x03>;
#size-cells = <0x02>;
device_type = "pci";
compatible = "pci1b36,1\0pciclass,060400\0pciclass,0604";
ranges;
reg = <0x50000 0xffff6d76 0xc2b49780 0xffff6d76 0xc2b30100>;
};
};
};[...]
};
--- 8< ---
Best regards,
Hervé
Signature · 3 lines
Hervé Codina, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
Rob Herring
maintainerRe: [PATCH V9 5/5] of: unittest: Add pci_dt_testdrv pci driver
Quoted 20 lines · Herve Codina
Hi all,
Quoted 5 lines · On Wed, 21 Jun 2023 10:34:09 -0700 Lizhi Hou <[email protected]> wrote:
pci_dt_testdrvis bound to QEMU PCI Test Device. It readsoverlay_pci_nodefdt fragment and apply it to Test Device. Then it callsof_platform_default_populate()to populate the platform devices.Quoted 8 lines
Signed-off-by Lizhi Hou <[email protected]>--- drivers/of/unittest-data/Makefile | 3 +- .../of/unittest-data/overlay_pci_node.dtso | 22 ++ drivers/of/unittest.c | 188 ++++++++++++++++++ drivers/pci/quirks.c | 1 + 4 files changed, 213 insertions(+), 1 deletion(-) create mode 100644 drivers/of/unittest-data/overlay_pci_node.dtso
Quoted 2 lines
Did the test under QEMU with the instructions that Lizhi provided at
https://github.com/houlz0507/xoclv2/blob/pci-dt-0329/pci-dt-patch-0329/README
Instructions need to be in the tree, not living somewhere else. Don't need the full QEMU setup, but just stating 'add "-device pci-testdev"' somewhere. Probably in the test failure messages would be the most helpful location.
Quoted 16 lines
The unittest results were:
--- 8< ---[ 1.107378] ### dt-test ### pass of_unittest_lifecycle():3273 [ 1.110068] ### dt-test ### pass of_unittest_pci_node():3909 [ 1.110401] ### dt-test ### pass unittest_pci_probe():3840 [ 1.110618] ### dt-test ### pass of_unittest_pci_node():3914 [ 1.110759] ### dt-test ### pass of_unittest_pci_node_verify():3870 [ 1.110894] ### dt-test ### pass of_unittest_pci_node_verify():3877 [ 1.110985] ### dt-test ### pass of_unittest_pci_node_verify():3884 [ 1.111088] ### dt-test ### pass of_unittest_pci_node():3926 [ 1.111171] ### dt-test ### pass of_unittest_pci_node():3927 [ 1.112056] ### dt-test ### pass of_unittest_pci_node_verify():3870 [ 1.112201] ### dt-test ### pass of_unittest_pci_node_verify():3890 [ 1.112326] ### dt-test ### pass of_unittest_pci_node_verify():3892 [ 1.112489] ### dt-test ### pass of_unittest_check_tree_linkage():271
Quoted 8 lines
--- 8< ---
Based on the test provided, no failure detected.
Tested-by Herve Codina <[email protected]>Further more, I dumped the dt (PCI related nodes) available on the target. If someone needs to look at it:
Thanks!
Quoted 27 lines
--- 8< ---
# cat /tmp/dt.dts /dts-v1/;/ { #address-cells = <0x02>; #size-cells = <0x02>; interrupt-parent = <0x8002>; compatible = "linux,dummy-virt"; name = [00]; [...] pcie@10000000 { #address-cells = <0x03>; dma-coherent; bus-range = <0x00 0xff>; interrupt-map = <0x00 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x03 0x04 0x00 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x04 0x04 0x00 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x05 0x04 0x00 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x06 0x04 0x800 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x04 0x04 0x800 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x05 0x04 0x800 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x06 0x04 0x800 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x03 0x04 0x1000 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x05 0x04 0x1000 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x06 0x04 0x1000 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x03 0x04 0x1000 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x04 0x04 0x1800 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x06 0x04 0x1800 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x03 0x04 0x1800 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x04 0x04 0x1800 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x05 0x04>; #size-cells = <0x02>; device_type = "pci"; interrupt-map-mask = <0x1800 0x00 0x00 0x07>; compatible = "pci-host-ecam-generic"; ranges = <0x1000000 0x00 0x00 0x00 0x3eff0000 0x00 0x10000 0x2000000 0x00 0x10000000 0x00 0x10000000 0x00 0x2eff0000 0x3000000 0x80 0x00 0x80 0x00 0x80 0x00>; #interrupt-cells = <0x01>; reg = <0x40 0x10000000 0x00 0x10000000>; linux,pci-domain = <0x00>; msi-parent = <0x8003>; name = "pcie";
Quoted 7 lines
pci@3,0 {
#address-cells = <0x03>;
#size-cells = <0x02>;
device_type = "pci";
compatible = "pci1b36,c\0pciclass,060400\0pciclass,0604";
ranges = <0x81001800 0x00 0x1000 0x81001800 0x00 0x1000 0x00 0x2000 0x82001800 0x00 0x10000000 0x82001800 0x00 0x10000000 0x00 0x200000 0xc3001800 0x80 0x00 0xc3001800 0x80 0x00 0x00 0x200000>;
reg = <0x1800 0xffff6d76 0xc2b23600 0xffff6d76 0x3fbf63a0>;Something looks wrong with the values here. I found this running it thru dtc.
<stdout>: Warning (pci_device_reg): /pcie@10000000/pci@3,0:reg: PCI reg config space address cells 2 and 3 must be 0
Rob
Re: [PATCH V9 5/5] of: unittest: Add pci_dt_testdrv pci driver
Quoted 19 lines · Rob Herring
Quoted 18 lines · Herve Codina
Hi all,
Quoted 13 lines · On Wed, 21 Jun 2023 10:34:09 -0700 Lizhi Hou <[email protected]> wrote:
pci_dt_testdrvis bound to QEMU PCI Test Device. It readsoverlay_pci_nodefdt fragment and apply it to Test Device. Then it callsof_platform_default_populate()to populate the platform devices.Signed-off-by Lizhi Hou <[email protected]>--- drivers/of/unittest-data/Makefile | 3 +- .../of/unittest-data/overlay_pci_node.dtso | 22 ++ drivers/of/unittest.c | 188 ++++++++++++++++++ drivers/pci/quirks.c | 1 + 4 files changed, 213 insertions(+), 1 deletion(-)create mode 100644
drivers/of/unittest-data/overlay_pci_node.dtso
Quoted 6 lines
Quoted 2 lines
Did the test under QEMU with the instructions that Lizhi provided at
https://github.com/houlz0507/xoclv2/blob/pci-dt-0329/pci-dt-patch-0329/READMEInstructions need to be in the tree, not living somewhere else. Don't need the full QEMU setup, but just stating 'add "-device pci-testdev"' somewhere. Probably in the test failure messages would be the most helpful location.
Sure. I will add this to the test failure message.
Quoted 60 lines
Quoted 16 lines
The unittest results were:
--- 8< ---[ 1.107378] ### dt-test ### pass of_unittest_lifecycle():3273 [ 1.110068] ### dt-test ### pass of_unittest_pci_node():3909 [ 1.110401] ### dt-test ### pass unittest_pci_probe():3840 [ 1.110618] ### dt-test ### pass of_unittest_pci_node():3914 [ 1.110759] ### dt-test ### pass of_unittest_pci_node_verify():3870 [ 1.110894] ### dt-test ### pass of_unittest_pci_node_verify():3877 [ 1.110985] ### dt-test ### pass of_unittest_pci_node_verify():3884 [ 1.111088] ### dt-test ### pass of_unittest_pci_node():3926 [ 1.111171] ### dt-test ### pass of_unittest_pci_node():3927 [ 1.112056] ### dt-test ### pass of_unittest_pci_node_verify():3870 [ 1.112201] ### dt-test ### pass of_unittest_pci_node_verify():3890 [ 1.112326] ### dt-test ### pass of_unittest_pci_node_verify():3892 [ 1.112489] ### dt-test ### pass of_unittest_check_tree_linkage():271Quoted 8 lines
--- 8< ---
Based on the test provided, no failure detected.
Tested-by Herve Codina <[email protected]>Further more, I dumped the dt (PCI related nodes) available on the target. If someone needs to look at it:
Thanks!
Quoted 27 lines
--- 8< ---
# cat /tmp/dt.dts /dts-v1/;/ { #address-cells = <0x02>; #size-cells = <0x02>; interrupt-parent = <0x8002>; compatible = "linux,dummy-virt"; name = [00]; [...] pcie@10000000 { #address-cells = <0x03>; dma-coherent; bus-range = <0x00 0xff>; interrupt-map = <0x00 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x03 0x04 0x00 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x04 0x04 0x00 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x05 0x04 0x00 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x06 0x04 0x800 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x04 0x04 0x800 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x05 0x04 0x800 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x06 0x04 0x800 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x03 0x04 0x1000 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x05 0x04 0x1000 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x06 0x04 0x1000 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x03 0x04 0x1000 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x04 0x04 0x1800 0x00 0x00 0x01 0x8002 0x00 0x00 0x00 0x06 0x04 0x1800 0x00 0x00 0x02 0x8002 0x00 0x00 0x00 0x03 0x04 0x1800 0x00 0x00 0x03 0x8002 0x00 0x00 0x00 0x04 0x04 0x1800 0x00 0x00 0x04 0x8002 0x00 0x00 0x00 0x05 0x04>; #size-cells = <0x02>; device_type = "pci"; interrupt-map-mask = <0x1800 0x00 0x00 0x07>; compatible = "pci-host-ecam-generic"; ranges = <0x1000000 0x00 0x00 0x00 0x3eff0000 0x00 0x10000 0x2000000 0x00 0x10000000 0x00 0x10000000 0x00 0x2eff0000 0x3000000 0x80 0x00 0x80 0x00 0x80 0x00>; #interrupt-cells = <0x01>; reg = <0x40 0x10000000 0x00 0x10000000>; linux,pci-domain = <0x00>; msi-parent = <0x8003>; name = "pcie";Quoted 7 lines
pci@3,0 { #address-cells = <0x03>; #size-cells = <0x02>; device_type = "pci"; compatible = "pci1b36,c\0pciclass,060400\0pciclass,0604"; ranges = <0x81001800 0x00 0x1000 0x81001800 0x00 0x1000 0x00 0x2000 0x82001800 0x00 0x10000000 0x82001800 0x00 0x10000000 0x00 0x200000 0xc3001800 0x80 0x00 0xc3001800 0x80 0x00 0x00 0x200000>; reg = <0x1800 0xffff6d76 0xc2b23600 0xffff6d76 0x3fbf63a0>;
Quoted 4 lines
Something looks wrong with the values here. I found this running it thru dtc.
<stdout>: Warning (
pci_device_reg): /pcie@10000000/pci@3,0:reg: PCI reg config space address cells 2 and 3 must be 0
I will fix this. Thanks.
Lizhi
Quoted 2 lines
Rob
Quoted 43 lines · Lizhi Hou
This patch series introduces OF overlay support for PCI devices which primarily addresses two use cases. First, it provides a data driven method to describe hardware peripherals that are present in a PCI endpoint and hence can be accessed by the PCI host. Second, it allows reuse of a OF compatible driver -- often used in SoC platforms -- in a PCI host based system.
There are 2 series devices rely on this patch:
1) Xilinx Alveo Accelerator cards (FPGA based device)
2) Microchip LAN9662 Ethernet ControllerPlease see: https://lore.kernel.org/lkml/[email protected]/Normally, the PCI core discovers PCI devices and their BARs using the PCI enumeration process. However, the process does not provide a way to discover the hardware peripherals that are present in a PCI device, and which can be accessed through the PCI BARs. Also, the enumeration process does not provide a way to associate MSI-X vectors of a PCI device with the hardware peripherals that are present in the device. PCI device drivers often use header files to describe the hardware peripherals and their resources as there is no standard data driven way to do so. This patch series proposes to use flattened device tree blob to describe the peripherals in a data driven way. Based on previous discussion, using device tree overlay is the best way to unflatten the blob and populate platform devices. To use device tree overlay, there are three obvious problems that need to be resolved.
First, we need to create a base tree for non-DT system such as
x86_64. A patch series has been submitted for this:
https://lore.kernel.org/lkml/[email protected]/
https://lore.kernel.org/lkml/[email protected]/Second, a device tree node corresponding to the PCI endpoint is required for overlaying the flattened device tree blob for that PCI endpoint. Because PCI is a self-discoverable bus, a device tree node is usually not created for PCI devices. This series adds support to generate a device tree node for a PCI device which advertises itself using PCI quirks infrastructure.
Third, we need to generate device tree nodes for PCI bridges since a child PCI endpoint may choose to have a device tree node created.
Quoted 6 lines
This patch series is made up of three patches.
The first patch is adding OF interface to create or destroy OF node dynamically.
The second patch introduces a kernel option,
CONFIG_DYNAMIC_PCI_OF_NODEX.
In case this log becomes part of the merge commit or something,
s/CONFIG_DYNAMIC_PCI_OF_NODEX/CONFIG_PCI_DYNAMIC_OF_NODES/
Quoted 7 lines
When the option is turned on, the kernel will generate device tree nodes for all PCI bridges unconditionally. The patch also shows how to use the PCI quirks infrastructure,
DECLARE_PCI_FIXUP_FINALto generate a device tree node for a device. Specifically, the patch generates a device tree node for Xilinx Alveo U50 PCIe accelerator device. The generated device tree nodes do not have any property.
Quoted 5 lines
The third patch adds basic properties ('reg', 'compatible' and '
device_type') to the dynamically generated device tree nodes. More properties can be added in the future.Here is the example of device tree nodes generated within the ARM64 QEMU.
It's not obvious to me what was there originally and what was added because of this series.
Quoted 70 lines
# lspci -t
-[0000:00]-+-00.0
+-01.0
+-03.0-[01-03]----00.0-[02-03]----00.0-[03]----00.0
+-03.1-[04]--
\-04.0-[05-06]----00.0-[06]--
# tree /sys/firmware/devicetree/base/pcie\@10000000
/sys/firmware/devicetree/base/pcie@10000000
|-- #address-cells
|-- #interrupt-cells
|-- #size-cells
|-- bus-range
|-- compatible
|-- device_type
|-- dma-coherent
|-- interrupt-map
|-- interrupt-map-mask
|-- linux,pci-domain
|-- msi-map
|-- name
|-- pci@3,0
| |-- #address-cells
| |-- #size-cells
| |-- compatible
| |-- device_type
| |-- pci@0,0
| | |-- #address-cells
| | |-- #size-cells
| | |-- compatible
| | |-- device_type
| | |-- pci@0,0
| | | |-- #address-cells
| | | |-- #size-cells
| | | |-- compatible
| | | |-- dev@0,0
| | | | |-- #address-cells
| | | | |-- #size-cells
| | | | |-- compatible
| | | | |-- ranges
| | | | `-- reg
| | | |-- device_type
| | | |-- ranges
| | | `-- reg
| | |-- ranges
| | `-- reg
| |-- ranges
| `-- reg
|-- pci@3,1
| |-- #address-cells
| |-- #size-cells
| |-- compatible
| |-- device_type
| |-- ranges
| `-- reg
|-- pci@4,0
| |-- #address-cells
| |-- #size-cells
| |-- compatible
| |-- device_type
| |-- pci@0,0
| | |-- #address-cells
| | |-- #size-cells
| | |-- compatible
| | |-- device_type
| | |-- ranges
| | `-- reg
| |-- ranges
| `-- reg
|-- ranges
`-- reg