docs: ABI: sysfs-class-led-trigger-netdev: add new modes and entry
Subsystems (3)
PATCH 1/1 docs: ABI: sysfs-class-led-trigger-netdev: add new modes and entry
Document newly introduced modes and entry for the LED netdev trigger.
Add documentation for new modes:
- link_10
- link_100
- link_1000
- half_duplex
- full_duplex
Add documentation for new entry:
- hw_control
Also add additional info for the interval entry and the tx/rx modes with the special case of hw_control ON.
--- .../testing/sysfs-class-led-trigger-netdev | 89 +++++++++++++++++++ 1 file changed, 89 insertions(+)
Documentation/ABI/testing/sysfs-class-led-trigger-netdev +89 -0
@@ -13,6 +13,11 @@ Description: Specifies the duration of the LED blink in milliseconds. Defaults to 50 ms. + With hw_control ON, the interval value MUST be set to the + default value and cannot be changed. + Trying to set any value in this specific mode will return + an EINVAL error. + What: /sys/class/leds/<led>/link Date: Dec 2017 KernelVersion: 4.16
@@ -39,6 +44,9 @@ Description: If set to 1, the LED will blink for the milliseconds specified in interval to signal transmission. + With hw_control ON, the blink interval is controlled by hardware + and won't reflect the value set in interval. + What: /sys/class/leds/<led>/rx Date: Dec 2017 KernelVersion: 4.16
@@ -50,3 +58,84 @@ Description: If set to 1, the LED will blink for the milliseconds specified in interval to signal reception. + + With hw_control ON, the blink interval is controlled by hardware + and won't reflect the value set in interval. + +What: /sys/class/leds/<led>/hw_control +Date: Jun 2023 +KernelVersion: 6.5 +Contact: [email protected] +Description: + Communicate whether the LED trigger modes are driven by hardware + or software fallback is used. + + If 0, the LED is using software fallback to blink. + + If 1, the LED is using hardware control to blink and signal the + requested modes. + +What: /sys/class/leds/<led>/link_10 +Date: Jun 2023 +KernelVersion: 6.5 +Contact: [email protected] +Description: + Signal the link speed state of 10Mbps of the named network device. + + If set to 0 (default), the LED's normal state is off. + + If set to 1, the LED's normal state reflects the link state + speed of 10MBps of the named network device. + Setting this value also immediately changes the LED state. + +What: /sys/class/leds/<led>/link_100 +Date: Jun 2023 +KernelVersion: 6.5 +Contact: [email protected] +Description: + Signal the link speed state of 100Mbps of the named network device. + + If set to 0 (default), the LED's normal state is off. + + If set to 1, the LED's normal state reflects the link state + speed of 100Mbps of the named network device. + Setting this value also immediately changes the LED state. + +What: /sys/class/leds/<led>/link_1000 +Date: Jun 2023 +KernelVersion: 6.5 +Contact: [email protected] +Description: + Signal the link speed state of 1000Mbps of the named network device. + + If set to 0 (default), the LED's normal state is off. + + If set to 1, the LED's normal state reflects the link state + speed of 1000Mbps of the named network device. + Setting this value also immediately changes the LED state. + +What: /sys/class/leds/<led>/half_duplex +Date: Jun 2023 +KernelVersion: 6.5 +Contact: [email protected] +Description: + Signal the link half duplex state of the named network device. + + If set to 0 (default), the LED's normal state is off. + + If set to 1, the LED's normal state reflects the link half + duplex state of the named network device. + Setting this value also immediately changes the LED state. + +What: /sys/class/leds/<led>/full_duplex +Date: Jun 2023 +KernelVersion: 6.5 +Contact: [email protected] +Description: + Signal the link full duplex state of the named network device. + + If set to 0 (default), the LED's normal state is off. + + If set to 1, the LED's normal state reflects the link full + duplex state of the named network device. + Setting this value also immediately changes the LED state.
Signature · 1 line
2.40.1
Quoted 9 lines · Christian Marangi
Document newly introduced modes and entry for the LED netdev trigger.
Add documentation for new modes:
-link_10
-link_100
-link_1000
-half_duplex
-full_duplex
Quoted 7 lines
Add documentation for new entry:
-hw_controlAlso add additional info for the interval entry and the tx/rx modes with the special case of
hw_controlON.Signed-off-by Christian Marangi <[email protected]>
Andrew
This patch was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Hello:
This patch was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Quoted 10 lines · On Wed, 21 Jun 2023 11:26:53 +0200 you wrote:
Document newly introduced modes and entry for the LED netdev trigger.
Add documentation for new modes:
-link_10
-link_100
-link_1000
-half_duplex
-full_duplex[...]
Here is the summary with links:
- [net-next] docs: ABI: sysfs-class-led-trigger-netdev: add new modes and entry
https://git.kernel.org/netdev/net-next/c/2ffb8d02a9b6
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html