dt-bindings: input: touchscreen: convert ad7879 to yaml format
Subsystems (4)
Frank Li
maintainerPATCH v2 1/1 dt-bindings: input: touchscreen: convert ad7879 to yaml format
Convert binding doc ad7879.txt to yaml format.
Additional change:
- Add ref to /schemas/spi/spi-peripheral-props.yaml
- Add #gpio-cell
- Remove spi-cpol and spi-cpha in example, the place hold 'spi' can't correct detect spi-controler.yaml. So these two properties can't be recongnized.
Fix warning:arch/arm64/boot/dts/freescale/imx8dx-colibri-aster.dtb:
/bus@5a000000/i2c@5a800000/touchscreen@2c: failed to match any schema with compatible: ['adi,ad7879-1']
---
Change from v1 to v2:
- add default 0
--- .../bindings/input/touchscreen/ad7879.txt | 71 --------- .../input/touchscreen/adi,ad7879.yaml | 150 ++++++++++++++++++ 2 files changed, 150 insertions(+), 71 deletions(-) delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/ad7879.txt create mode 100644 Documentation/devicetree/bindings/input/touchscreen/adi,ad7879.yaml
Documentation/devicetree/bindings/input/touchscreen/ad7879.txt deleted +0 -71
@@ -1,71 +0,0 @@ -* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C) - -Required properties: -- compatible : for SPI slave, use "adi,ad7879" - for I2C slave, use "adi,ad7879-1" -- reg : SPI chipselect/I2C slave address - See spi-bus.txt for more SPI slave properties -- interrupts : touch controller interrupt -- touchscreen-max-pressure : maximum reported pressure -- adi,resistance-plate-x : total resistance of X-plate (for pressure - calculation) -Optional properties: -- touchscreen-swapped-x-y : X and Y axis are swapped (boolean) -- adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us) - 13 : 2.560ms - 14 : 3.584ms - 15 : 4.096ms - This property has to be a '/bits/ 8' value -- adi,acquisition-time : 0: 2us - 1: 4us - 2: 8us - 3: 16us - This property has to be a '/bits/ 8' value -- adi,median-filter-size : 0: disabled - 1: 4 measurements - 2: 8 measurements - 3: 16 measurements - This property has to be a '/bits/ 8' value -- adi,averaging : 0: 2 middle values (1 if median disabled) - 1: 4 middle values - 2: 8 middle values - 3: 16 values - This property has to be a '/bits/ 8' value -- adi,conversion-interval: : 0 : convert one time only - 1-255: 515us + val * 35us (up to 9.440ms) - This property has to be a '/bits/ 8' value -- gpio-controller : Switch AUX/VBAT/GPIO pin to GPIO mode - -Example: - - touchscreen0@2c { - compatible = "adi,ad7879-1"; - reg = <0x2c>; - interrupt-parent = <&gpio1>; - interrupts = <13 IRQ_TYPE_EDGE_FALLING>; - touchscreen-max-pressure = <4096>; - adi,resistance-plate-x = <120>; - adi,first-conversion-delay = /bits/ 8 <3>; - adi,acquisition-time = /bits/ 8 <1>; - adi,median-filter-size = /bits/ 8 <2>; - adi,averaging = /bits/ 8 <1>; - adi,conversion-interval = /bits/ 8 <255>; - }; - - touchscreen1@1 { - compatible = "adi,ad7879"; - spi-max-frequency = <5000000>; - reg = <1>; - spi-cpol; - spi-cpha; - gpio-controller; - interrupt-parent = <&gpio1>; - interrupts = <13 IRQ_TYPE_EDGE_FALLING>; - touchscreen-max-pressure = <4096>; - adi,resistance-plate-x = <120>; - adi,first-conversion-delay = /bits/ 8 <3>; - adi,acquisition-time = /bits/ 8 <1>; - adi,median-filter-size = /bits/ 8 <2>; - adi,averaging = /bits/ 8 <1>; - adi,conversion-interval = /bits/ 8 <255>; - };
Documentation/devicetree/bindings/input/touchscreen/adi,ad7879.yaml new file +150 -0
150 lines not on this page · raw message
Signature · 1 line
2.34.1
Quoted 8 lines · Frank Li
Convert binding doc ad7879.txt to yaml format.
Additional change:
- Add ref to /schemas/spi/spi-peripheral-props.yaml
- Add #gpio-cell
- Remove spi-cpol and spi-cpha in example, the place hold 'spi' can't correct detectspi-controler.yaml. So these two properties can't be recongnized.
Quoted 5 lines
Fix warning:
arch/arm64/boot/dts/freescale/imx8dx-colibri-aster.dtb:
/bus@5a000000/i2c@5a800000/touchscreen@2c: failed to match any schema with compatible: ['adi,ad7879-1']Signed-off-by Frank Li <[email protected]>
Best regards,
Krzysztof
Quoted 8 lines · Frank Li
Convert binding doc ad7879.txt to yaml format.
Additional change:
- Add ref to /schemas/spi/spi-peripheral-props.yaml
- Add #gpio-cell
- Remove spi-cpol and spi-cpha in example, the place hold 'spi' can't correct detectspi-controler.yaml. So these two properties can't be recongnized.
Quoted 5 lines
Fix warning:
arch/arm64/boot/dts/freescale/imx8dx-colibri-aster.dtb:
/bus@5a000000/i2c@5a800000/touchscreen@2c: failed to match any schema with compatible: ['adi,ad7879-1']Signed-off-by Frank Li <[email protected]>
Applied, thank you.
Signature · 1 line
Dmitry