net: phy: split at803x
Subsystems (4)
v4 cover net: phy: split at803x
This is the last patchset of a long series of cleanup and preparation to make at803x better maintainable and permit the addition of other QCOM PHY Families.
A shared library modules is created since many QCOM PHY share similar/exact implementation and are reused.
This series doesn't introduce any new code but just move the function around and introduce a new module for all the functions that are shared between the 3 different PHY family.
Since the drivers are actually detached, new probe function are introduced that allocate the specific priv struct for the PHYs.
After this patch, qca808x will be further generalized as LED and cable test function are also used by the QCA807x PHYs. This is just for reference and the additional function move will be done on the relates specific series.
This is also needed in preparation for the introduction of qca807x PHYs family and PHY package concept.
Changes v4:
- Add Reviwed-by tag
- Correctly sort new define in makefile Changes v3:
- Fix compilation error on testing single change till patch 4. (improve bisectability of the series)
Changes v2:
- Out of RFC (at808x dependency got merged)
Christian Marangi (5):
net: phy: move at803x PHY driver to dedicated directory
net: phy: qcom: create and move functions to shared library
net: phy: qcom: deatch qca83xx PHY driver from at803x
net: phy: qcom: move additional functions to shared library
net: phy: qcom: detach qca808x PHY driver from at803x
drivers/net/phy/Kconfig | 7 +- drivers/net/phy/Makefile | 2 +- drivers/net/phy/at803x.c | 2759 --------------------------- drivers/net/phy/qcom/Kconfig | 22 + drivers/net/phy/qcom/Makefile | 5 + drivers/net/phy/qcom/at803x.c | 1140 +++++++++++ drivers/net/phy/qcom/qca808x.c | 934 +++++++++ drivers/net/phy/qcom/qca83xx.c | 275 +++ drivers/net/phy/qcom/qcom-phy-lib.c | 429 +++++ drivers/net/phy/qcom/qcom.h | 120 ++ 10 files changed, 2927 insertions(+), 2766 deletions(-) delete mode 100644 drivers/net/phy/at803x.c create mode 100644 drivers/net/phy/qcom/Kconfig create mode 100644 drivers/net/phy/qcom/Makefile create mode 100644 drivers/net/phy/qcom/at803x.c create mode 100644 drivers/net/phy/qcom/qca808x.c create mode 100644 drivers/net/phy/qcom/qca83xx.c create mode 100644 drivers/net/phy/qcom/qcom-phy-lib.c create mode 100644 drivers/net/phy/qcom/qcom.h
Signature · 1 line
2.43.0
PATCH v4 1/5 net: phy: move at803x PHY driver to dedicated directory
In preparation for addition of other Qcom PHY and to tidy things up, move the at803x PHY driver to dedicated directory.
The same order in the Kconfig selection is saved.
---
drivers/net/phy/Kconfig | 7 +------
drivers/net/phy/Makefile | 2 +-
drivers/net/phy/qcom/Kconfig | 7 +++++++
drivers/net/phy/qcom/Makefile | 2 ++
drivers/net/phy/{ => qcom}/at803x.c | 0
5 files changed, 11 insertions(+), 7 deletions(-)
create mode 100644 drivers/net/phy/qcom/Kconfig
create mode 100644 drivers/net/phy/qcom/Makefile
rename drivers/net/phy/{ => qcom}/at803x.c (100%)drivers/net/phy/Kconfig +1 -6
@@ -335,12 +335,7 @@ config NCN26000_PHY Currently supports the NCN26000 10BASE-T1S Industrial PHY with MII interface. -config AT803X_PHY - tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs" - depends on REGULATOR - help - Currently supports the AR8030, AR8031, AR8033, AR8035 and internal - QCA8337(Internal qca8k PHY) model +source "drivers/net/phy/qcom/Kconfig" config QSEMI_PHY tristate "Quality Semiconductor PHYs"
drivers/net/phy/Makefile +1 -1
@@ -36,7 +36,6 @@ obj-$(CONFIG_ADIN_PHY) += adin.o obj-$(CONFIG_ADIN1100_PHY) += adin1100.o obj-$(CONFIG_AMD_PHY) += amd.o obj-$(CONFIG_AQUANTIA_PHY) += aquantia/ -obj-$(CONFIG_AT803X_PHY) += at803x.o ifdef CONFIG_AX88796B_RUST_PHY obj-$(CONFIG_AX88796B_PHY) += ax88796b_rust.o else
@@ -91,6 +90,7 @@ endif obj-$(CONFIG_NXP_C45_TJA11XX_PHY) += nxp-c45-tja.o obj-$(CONFIG_NXP_CBTX_PHY) += nxp-cbtx.o obj-$(CONFIG_NXP_TJA11XX_PHY) += nxp-tja11xx.o +obj-y += qcom/ obj-$(CONFIG_QSEMI_PHY) += qsemi.o obj-$(CONFIG_REALTEK_PHY) += realtek.o obj-$(CONFIG_RENESAS_PHY) += uPD60620.o
drivers/net/phy/qcom/Kconfig new file +7 -0
@@ -0,0 +1,7 @@ +# SPDX-License-Identifier: GPL-2.0-only +config AT803X_PHY + tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs" + depends on REGULATOR + help + Currently supports the AR8030, AR8031, AR8033, AR8035 and internal + QCA8337(Internal qca8k PHY) model
drivers/net/phy/qcom/Makefile new file +2 -0
@@ -0,0 +1,2 @@ +# SPDX-License-Identifier: GPL-2.0 +obj-$(CONFIG_AT803X_PHY) += at803x.o
drivers/net/phy/qcom/at803x.c renamed from drivers/net/phy/at803x.c +0 -0
Signature · 1 line
2.43.0
PATCH v4 2/5 net: phy: qcom: create and move functions to shared library
In reply to Christian MarangiCreate and move functions to shared library in preparation for qca83xx PHY Family to be detached from at803x driver.
Only the shared defines are moved to the shared qcom.h header.
--- drivers/net/phy/qcom/Kconfig | 4 ++ drivers/net/phy/qcom/Makefile | 1 + drivers/net/phy/qcom/at803x.c | 69 +---------------------------- drivers/net/phy/qcom/qcom-phy-lib.c | 53 ++++++++++++++++++++++ drivers/net/phy/qcom/qcom.h | 34 ++++++++++++++ 5 files changed, 94 insertions(+), 67 deletions(-) create mode 100644 drivers/net/phy/qcom/qcom-phy-lib.c create mode 100644 drivers/net/phy/qcom/qcom.h
drivers/net/phy/qcom/Kconfig +4 -0
@@ -1,6 +1,10 @@ # SPDX-License-Identifier: GPL-2.0-only +config QCOM_NET_PHYLIB + tristate + config AT803X_PHY tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs" + select QCOM_NET_PHYLIB depends on REGULATOR help Currently supports the AR8030, AR8031, AR8033, AR8035 and internal
drivers/net/phy/qcom/Makefile +1 -0
@@ -1,2 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 +obj-$(CONFIG_QCOM_NET_PHYLIB) += qcom-phy-lib.o obj-$(CONFIG_AT803X_PHY) += at803x.o
drivers/net/phy/qcom/at803x.c +2 -67
99 lines not on this page · raw message
drivers/net/phy/qcom/qcom-phy-lib.c new file +53 -0
53 lines not on this page · raw message
drivers/net/phy/qcom/qcom.h new file +34 -0
@@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: GPL-2.0 */ + +#define AT803X_DEBUG_ADDR 0x1D +#define AT803X_DEBUG_DATA 0x1E + +#define AT803X_DEBUG_ANALOG_TEST_CTRL 0x00 +#define QCA8327_DEBUG_MANU_CTRL_EN BIT(2) +#define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2) +#define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15) + +#define AT803X_DEBUG_SYSTEM_CTRL_MODE 0x05 +#define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) + +#define AT803X_DEBUG_REG_HIB_CTRL 0x0b +#define AT803X_DEBUG_HIB_CTRL_SEL_RST_80U BIT(10) +#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13) +#define AT803X_DEBUG_HIB_CTRL_PS_HIB_EN BIT(15) + +enum stat_access_type { +PHY , +MMD +}; + +struct at803x_hw_stat { +const char *string; +u8 reg; +u32 mask; +enum stat_access_type access_type; +}; + +int at803x_debug_reg_read (struct phy_device *phydev,u16 reg); +int at803x_debug_reg_mask (struct phy_device *phydev,u16 reg, +u16 clear,u16 set); +int at803x_debug_reg_write (struct phy_device *phydev,u16 reg,u16 data);
Signature · 1 line
2.43.0
PATCH v4 3/5 net: phy: qcom: deatch qca83xx PHY driver from at803x
In reply to Christian MarangiDeatch qca83xx PHY driver from at803x.
The QCA83xx PHYs implement specific function and doesn't use generic at803x so it can be detached from the driver and moved to a dedicated one.
Probe function and priv struct is reimplemented to allocate and use only the qca83xx specific data. Unused data from at803x PHY driver are dropped from at803x priv struct.
This is to make slimmer PHY drivers instead of including lots of bloat that would never be used in specific SoC.
A new Kconfig flag QCA83XX_PHY is introduced to compile the new introduced PHY driver.
As the Kconfig name starts with Qualcomm the same order is kept.
--- drivers/net/phy/qcom/Kconfig | 11 +- drivers/net/phy/qcom/Makefile | 1 + drivers/net/phy/qcom/at803x.c | 235 ---------------------------- drivers/net/phy/qcom/qca83xx.c | 275 +++++++++++++++++++++++++++++++++ 4 files changed, 284 insertions(+), 238 deletions(-) create mode 100644 drivers/net/phy/qcom/qca83xx.c
drivers/net/phy/qcom/Kconfig +8 -3
@@ -3,9 +3,14 @@ config QCOM_NET_PHYLIB tristate config AT803X_PHY - tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs" + tristate "Qualcomm Atheros AR803X PHYs" select QCOM_NET_PHYLIB depends on REGULATOR help - Currently supports the AR8030, AR8031, AR8033, AR8035 and internal - QCA8337(Internal qca8k PHY) model + Currently supports the AR8030, AR8031, AR8033, AR8035 model + +config QCA83XX_PHY + tristate "Qualcomm Atheros QCA833x PHYs" + select QCOM_NET_PHYLIB + help + Currently supports the internal QCA8337(Internal qca8k PHY) model
drivers/net/phy/qcom/Makefile +1 -0
@@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_QCOM_NET_PHYLIB) += qcom-phy-lib.o obj-$(CONFIG_AT803X_PHY) += at803x.o +obj-$(CONFIG_QCA83XX_PHY) += qca83xx.o
drivers/net/phy/qcom/at803x.c +0 -235
288 lines not on this page · raw message
drivers/net/phy/qcom/qca83xx.c new file +275 -0
275 lines not on this page · raw message
Signature · 1 line
2.43.0
PATCH v4 4/5 net: phy: qcom: move additional functions to shared library
In reply to Christian MarangiMove additional functions to shared library in preparation for qca808x PHY Family to be detached from at803x driver.
Only the shared defines are moved to the shared qcom.h header.
--- drivers/net/phy/qcom/at803x.c | 426 +--------------------------- drivers/net/phy/qcom/qcom-phy-lib.c | 376 ++++++++++++++++++++++++ drivers/net/phy/qcom/qcom.h | 86 ++++++ 3 files changed, 463 insertions(+), 425 deletions(-)
drivers/net/phy/qcom/at803x.c +1 -425
@@ -24,65 +24,11 @@#include "qcom.h" -#define AT803X_SPECIFIC_FUNCTION_CONTROL 0x10 -#define AT803X_SFC_ASSERT_CRS BIT(11) -#define AT803X_SFC_FORCE_LINK BIT(10) -#define AT803X_SFC_MDI_CROSSOVER_MODE_M GENMASK(6, 5) -#define AT803X_SFC_AUTOMATIC_CROSSOVER 0x3 -#define AT803X_SFC_MANUAL_MDIX 0x1 -#define AT803X_SFC_MANUAL_MDI 0x0 -#define AT803X_SFC_SQE_TEST BIT(2) -#define AT803X_SFC_POLARITY_REVERSAL BIT(1) -#define AT803X_SFC_DISABLE_JABBER BIT(0) - -#define AT803X_SPECIFIC_STATUS 0x11 -#define AT803X_SS_SPEED_MASK GENMASK(15, 14) -#define AT803X_SS_SPEED_1000 2 -#define AT803X_SS_SPEED_100 1 -#define AT803X_SS_SPEED_10 0 -#define AT803X_SS_DUPLEX BIT(13) -#define AT803X_SS_SPEED_DUPLEX_RESOLVED BIT(11) -#define AT803X_SS_MDIX BIT(6) - -#define QCA808X_SS_SPEED_MASK GENMASK(9, 7) -#define QCA808X_SS_SPEED_2500 4 - -#define AT803X_INTR_ENABLE 0x12 -#define AT803X_INTR_ENABLE_AUTONEG_ERR BIT(15) -#define AT803X_INTR_ENABLE_SPEED_CHANGED BIT(14) -#define AT803X_INTR_ENABLE_DUPLEX_CHANGED BIT(13) -#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12) -#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11) -#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10) -#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8) -#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7) -#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5) -#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1) -#define AT803X_INTR_ENABLE_WOL BIT(0) - -#define AT803X_INTR_STATUS 0x13 - -#define AT803X_SMART_SPEED 0x14 -#define AT803X_SMART_SPEED_ENABLE BIT(5) -#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK GENMASK(4, 2) -#define AT803X_SMART_SPEED_BYPASS_TIMER BIT(1) -#define AT803X_CDT 0x16 -#define AT803X_CDT_MDI_PAIR_MASK GENMASK(9, 8) -#define AT803X_CDT_ENABLE_TEST BIT(0) -#define AT803X_CDT_STATUS 0x1c -#define AT803X_CDT_STATUS_STAT_NORMAL 0 -#define AT803X_CDT_STATUS_STAT_SHORT 1 -#define AT803X_CDT_STATUS_STAT_OPEN 2 -#define AT803X_CDT_STATUS_STAT_FAIL 3 -#define AT803X_CDT_STATUS_STAT_MASK GENMASK(9, 8) -#define AT803X_CDT_STATUS_DELTA_TIME_MASK GENMASK(7, 0)#define AT803X_LED_CONTROL 0x18#define AT803X_PHY_MMD3_WOL_CTRL 0x8012#define AT803X_WOL_EN BIT(5) -#define AT803X_LOC_MAC_ADDR_0_15_OFFSET 0x804C -#define AT803X_LOC_MAC_ADDR_16_31_OFFSET 0x804B -#define AT803X_LOC_MAC_ADDR_32_47_OFFSET 0x804A +#define AT803X_REG_CHIP_CONFIG 0x1f#define AT803X_BT_BX_REG_SEL 0x8000
@@ -138,10 +84,6 @@#define AT803X_CLK_OUT_STRENGTH_HALF 1#define AT803X_CLK_OUT_STRENGTH_QUARTER 2 -#define AT803X_DEFAULT_DOWNSHIFT 5 -#define AT803X_MIN_DOWNSHIFT 2 -#define AT803X_MAX_DOWNSHIFT 9 -#define AT803X_MMD3_SMARTEEE_CTL1 0x805b#define AT803X_MMD3_SMARTEEE_CTL2 0x805c#define AT803X_MMD3_SMARTEEE_CTL3 0x805d
@@ -366,11 +308,6 @@ MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");MODULE_AUTHOR ("Matus Ujhelyi" );MODULE_LICENSE ("GPL" ); -struct at803x_ss_mask { -u16 speed_mask; -u8 speed_shift; -}; -struct at803x_priv {int flags;u16 clk_25m_reg;
@@ -470,80 +407,6 @@ static void at803x_context_restore(struct phy_device *phydev,phy_write (phydev,AT803X_LED_CONTROL , context->led_control); } -static int at803x_set_wol (struct phy_device *phydev, -struct ethtool_wolinfo *wol) -{ -int ret, irq_enabled; - -if (wol->wolopts &WAKE_MAGIC ) { -struct net_device *ndev = phydev->attached_dev; -const u8 *mac; -unsigned int i; -static const unsigned int offsets[] = { -AT803X_LOC_MAC_ADDR_32_47_OFFSET , -AT803X_LOC_MAC_ADDR_16_31_OFFSET , -AT803X_LOC_MAC_ADDR_0_15_OFFSET , - }; - -if (!ndev) -return -ENODEV ; - - mac = (const u8 *)ndev->dev_addr; - -if (!is_valid_ether_addr (mac)) -return -EINVAL ; - -for (i =0 ; i <3 ; i++) -phy_write_mmd (phydev,MDIO_MMD_PCS , offsets[i], - mac[(i *2 ) +1 ] | (mac[(i *2 )] <<8 )); - -/* Enable WOL interrupt */ - ret =phy_modify (phydev,AT803X_INTR_ENABLE ,0 ,AT803X_INTR_ENABLE_WOL ); -if (ret) -return ret; - }else { -/* Disable WOL interrupt */ - ret =phy_modify (phydev,AT803X_INTR_ENABLE ,AT803X_INTR_ENABLE_WOL ,0 ); -if (ret) -return ret; - } - -/* Clear WOL status */ - ret =phy_read (phydev,AT803X_INTR_STATUS ); -if (ret <0 ) -return ret; - -/* Check if there are other interrupts except for WOL triggered when PHY is -* in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can -* be passed up to the interrupt PIN. -*/ - irq_enabled =phy_read (phydev,AT803X_INTR_ENABLE ); -if (irq_enabled <0 ) -return irq_enabled; - - irq_enabled &= ~AT803X_INTR_ENABLE_WOL ; -if (ret & irq_enabled && !phy_polling_mode (phydev)) -phy_trigger_machine (phydev); - -return 0 ; -} - -static void at803x_get_wol (struct phy_device *phydev, -struct ethtool_wolinfo *wol) -{ -int value; - - wol->supported =WAKE_MAGIC ; - wol->wolopts =0 ; - - value =phy_read (phydev,AT803X_INTR_ENABLE ); -if (value <0 ) -return ; - -if (value &AT803X_INTR_ENABLE_WOL ) - wol->wolopts |=WAKE_MAGIC ; -} -static int at803x_suspend (struct phy_device *phydev) {int value;
@@ -816,73 +679,6 @@ static int at803x_config_init(struct phy_device *phydev)return phy_modify (phydev,MII_ADVERTISE ,MDIO_AN_CTRL1_XNP ,0 ); } -static int at803x_ack_interrupt (struct phy_device *phydev) -{ -int err; - - err =phy_read (phydev,AT803X_INTR_STATUS ); - -return (err <0 ) ? err :0 ; -} - -static int at803x_config_intr (struct phy_device *phydev) -{ -int err; -int value; - - value =phy_read (phydev,AT803X_INTR_ENABLE ); - -if (phydev->interrupts ==PHY_INTERRUPT_ENABLED ) { -/* Clear any pending interrupts */ - err =at803x_ack_interrupt (phydev); -if (err) -return err; - - value |=AT803X_INTR_ENABLE_AUTONEG_ERR ; - value |=AT803X_INTR_ENABLE_SPEED_CHANGED ; - value |=AT803X_INTR_ENABLE_DUPLEX_CHANGED ; - value |=AT803X_INTR_ENABLE_LINK_FAIL ; - value |=AT803X_INTR_ENABLE_LINK_SUCCESS ; - - err =phy_write (phydev,AT803X_INTR_ENABLE , value); - }else { - err =phy_write (phydev,AT803X_INTR_ENABLE ,0 ); -if (err) -return err; - -/* Clear any pending interrupts */ - err =at803x_ack_interrupt (phydev); - } - -return err; -} - -static irqreturn_t at803x_handle_interrupt (struct phy_device *phydev) -{ -int irq_status, int_enabled; - - irq_status =phy_read (phydev,AT803X_INTR_STATUS ); -if (irq_status <0 ) { -phy_error (phydev); -return IRQ_NONE ; - } - -/* Read the current enabled interrupts */ - int_enabled =phy_read (phydev,AT803X_INTR_ENABLE ); -if (int_enabled <0 ) { -phy_error (phydev); -return IRQ_NONE ; - } - -/* See if this was one of our enabled interrupts */ -if (!(irq_status & int_enabled)) -return IRQ_NONE ; - -phy_trigger_machine (phydev); - -return IRQ_HANDLED ; -} -static void at803x_link_change_notify (struct phy_device *phydev) {/*
@@ -908,69 +704,6 @@ static void at803x_link_change_notify(struct phy_device *phydev) } } -static int at803x_read_specific_status (struct phy_device *phydev, -struct at803x_ss_mask ss_mask) -{ -int ss; - -/* Read the AT8035 PHY-Specific Status register, which indicates the -* speed and duplex that the PHY is actually using, irrespective of -* whether we are in autoneg mode or not. -*/ - ss =phy_read (phydev,AT803X_SPECIFIC_STATUS ); -if (ss <0 ) -return ss; - -if (ss &AT803X_SS_SPEED_DUPLEX_RESOLVED ) { -int sfc, speed; - - sfc =phy_read (phydev,AT803X_SPECIFIC_FUNCTION_CONTROL ); -if (sfc <0 ) -return sfc; - - speed = ss & ss_mask.speed_mask; - speed >>= ss_mask.speed_shift; - -switch (speed) { -case AT803X_SS_SPEED_10 : - phydev->speed =SPEED_10 ; -break ; -case AT803X_SS_SPEED_100 : - phydev->speed =SPEED_100 ; -break ; -case AT803X_SS_SPEED_1000 : - phydev->speed =SPEED_1000 ; -break ; -case QCA808X_SS_SPEED_2500 : - phydev->speed =SPEED_2500 ; -break ; - } -if (ss &AT803X_SS_DUPLEX ) - phydev->duplex =DUPLEX_FULL ; -else - phydev->duplex =DUPLEX_HALF ; - -if (ss &AT803X_SS_MDIX ) - phydev->mdix =ETH_TP_MDI_X ; -else - phydev->mdix =ETH_TP_MDI ; - -switch (FIELD_GET (AT803X_SFC_MDI_CROSSOVER_MODE_M , sfc)) { -case AT803X_SFC_MANUAL_MDI : - phydev->mdix_ctrl =ETH_TP_MDI ; -break ; -case AT803X_SFC_MANUAL_MDIX : - phydev->mdix_ctrl =ETH_TP_MDI_X ; -break ; -case AT803X_SFC_AUTOMATIC_CROSSOVER : - phydev->mdix_ctrl =ETH_TP_MDI_AUTO ; -break ; - } - } - -return 0 ; -} -static int at803x_read_status (struct phy_device *phydev) {struct at803x_ss_mask ss_mask = {0 };
@@ -1006,50 +739,6 @@ static int at803x_read_status(struct phy_device *phydev)return 0 ; } -static int at803x_config_mdix (struct phy_device *phydev,u8 ctrl) -{ -u16 val; - -switch (ctrl) { -case ETH_TP_MDI : - val =AT803X_SFC_MANUAL_MDI ; -break ; -case ETH_TP_MDI_X : - val =AT803X_SFC_MANUAL_MDIX ; -break ; -case ETH_TP_MDI_AUTO : - val =AT803X_SFC_AUTOMATIC_CROSSOVER ; -break ; -default : -return 0 ; - } - -return phy_modify_changed (phydev,AT803X_SPECIFIC_FUNCTION_CONTROL , -AT803X_SFC_MDI_CROSSOVER_MODE_M , -FIELD_PREP (AT803X_SFC_MDI_CROSSOVER_MODE_M , val)); -} - -static int at803x_prepare_config_aneg (struct phy_device *phydev) -{ -int ret; - - ret =at803x_config_mdix (phydev, phydev->mdix_ctrl); -if (ret <0 ) -return ret; - -/* Changes of the midx bits are disruptive to the normal operation; -* therefore any changes to these registers must be followed by a -* software reset to take effect. -*/ -if (ret ==1 ) { - ret =genphy_soft_reset (phydev); -if (ret <0 ) -return ret; - } - -return 0 ; -} -static int at803x_config_aneg (struct phy_device *phydev) {struct at803x_priv *priv = phydev->priv;
@@ -1065,80 +754,6 @@ static int at803x_config_aneg(struct phy_device *phydev)return genphy_config_aneg (phydev); } -static int at803x_get_downshift (struct phy_device *phydev,u8 *d) -{ -int val; - - val =phy_read (phydev,AT803X_SMART_SPEED ); -if (val <0 ) -return val; - -if (val &AT803X_SMART_SPEED_ENABLE ) - *d =FIELD_GET (AT803X_SMART_SPEED_RETRY_LIMIT_MASK , val) +2 ; -else - *d =DOWNSHIFT_DEV_DISABLE ; - -return 0 ; -} - -static int at803x_set_downshift (struct phy_device *phydev,u8 cnt) -{ -u16 mask, set; -int ret; - -switch (cnt) { -case DOWNSHIFT_DEV_DEFAULT_COUNT : - cnt =AT803X_DEFAULT_DOWNSHIFT ; - fallthrough; - case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT: - set =AT803X_SMART_SPEED_ENABLE | -AT803X_SMART_SPEED_BYPASS_TIMER | -FIELD_PREP (AT803X_SMART_SPEED_RETRY_LIMIT_MASK , cnt -2 ); - mask =AT803X_SMART_SPEED_RETRY_LIMIT_MASK ; -break ; -case DOWNSHIFT_DEV_DISABLE : - set =0 ; - mask =AT803X_SMART_SPEED_ENABLE | -AT803X_SMART_SPEED_BYPASS_TIMER ; -break ; -default : -return -EINVAL ; - } - - ret =phy_modify_changed (phydev,AT803X_SMART_SPEED , mask, set); - -/* After changing the smart speed settings, we need to perform a -* software reset, use phy_init_hw() to make sure we set the -* reapply any values which might got lost during software reset. -*/ -if (ret ==1 ) - ret =phy_init_hw (phydev); - -return ret; -} - -static int at803x_get_tunable (struct phy_device *phydev, -struct ethtool_tunable *tuna,void *data) -{ -switch (tuna->id) { -case ETHTOOL_PHY_DOWNSHIFT : -return at803x_get_downshift (phydev, data); -default : -return -EOPNOTSUPP ; - } -} - -static int at803x_set_tunable (struct phy_device *phydev, -struct ethtool_tunable *tuna,const void *data) -{ -switch (tuna->id) { -case ETHTOOL_PHY_DOWNSHIFT : -return at803x_set_downshift (phydev, *(const u8 *)data); -default : -return -EOPNOTSUPP ; - } -} -static int at803x_cable_test_result_trans (u16 status) {switch (FIELD_GET (AT803X_CDT_STATUS_STAT_MASK , status)) {
@@ -1170,45 +785,6 @@ static bool at803x_cdt_fault_length_valid(u16 status)return false; } -static int at803x_cdt_fault_length (int dt) -{ -/* According to the datasheet the distance to the fault is -* DELTA_TIME * 0.824 meters. -* -* The author suspect the correct formula is: -* -* fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2 -* -* where c is the speed of light, VF is the velocity factor of -* the twisted pair cable, 125MHz the counter frequency and -* we need to divide by 2 because the hardware will measure the -* round trip time to the fault and back to the PHY. -* -* With a VF of 0.69 we get the factor 0.824 mentioned in the -* datasheet. -*/ -return (dt *824 ) /10 ; -} - -static int at803x_cdt_start (struct phy_device *phydev, -u32 cdt_start) -{ -return phy_write (phydev,AT803X_CDT , cdt_start); -} - -static int at803x_cdt_wait_for_completion (struct phy_device *phydev, -u32 cdt_en) -{ -int val, ret; - -/* One test run takes about 25ms */ - ret =phy_read_poll_timeout (phydev,AT803X_CDT , val, - !(val & cdt_en), -30000 ,100000 , true); - -return ret <0 ? ret :0 ; -} -static int at803x_cable_test_one_pair (struct phy_device *phydev,int pair) {static const int ethtool_pair[] = {
drivers/net/phy/qcom/qcom-phy-lib.c +376 -0
385 lines not on this page · raw message
drivers/net/phy/qcom/qcom.h +86 -0
104 lines not on this page · raw message
Signature · 1 line
2.43.0
PATCH v4 5/5 net: phy: qcom: detach qca808x PHY driver from at803x
In reply to Christian MarangiAlmost all the QCA8081 PHY driver OPs are specific and only some of them use the generic at803x.
To make the at803x code slimmer, move all the specific qca808x regs and functions to a dedicated PHY driver.
Probe function and priv struct is reworked to allocate and use only the qca808x specific data. Unused data from at803x PHY driver are dropped from at803x priv struct.
Also a new Kconfig is introduced QCA808X_PHY, to compile the newly introduced PHY driver for QCA8081 PHY.
As the Kconfig name starts with Qualcomm the same order is kept.
--- drivers/net/phy/qcom/Kconfig | 6 + drivers/net/phy/qcom/Makefile | 1 + drivers/net/phy/qcom/at803x.c | 897 +------------------------------ drivers/net/phy/qcom/qca808x.c | 934 +++++++++++++++++++++++++++++++++ 4 files changed, 942 insertions(+), 896 deletions(-) create mode 100644 drivers/net/phy/qcom/qca808x.c
drivers/net/phy/qcom/Kconfig +6 -0
@@ -14,3 +14,9 @@ config QCA83XX_PHY select QCOM_NET_PHYLIB help Currently supports the internal QCA8337(Internal qca8k PHY) model + +config QCA808X_PHY + tristate "Qualcomm QCA808x PHYs" + select QCOM_NET_PHYLIB + help + Currently supports the QCA8081 model
drivers/net/phy/qcom/Makefile +1 -0
@@ -2,3 +2,4 @@ obj-$(CONFIG_QCOM_NET_PHYLIB) += qcom-phy-lib.o obj-$(CONFIG_AT803X_PHY) += at803x.o obj-$(CONFIG_QCA83XX_PHY) += qca83xx.o +obj-$(CONFIG_QCA808X_PHY) += qca808x.o
drivers/net/phy/qcom/at803x.c +1 -896
939 lines not on this page · raw message
drivers/net/phy/qcom/qca808x.c new file +934 -0
934 lines not on this page · raw message
Signature · 1 line
2.43.0
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Hello:
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Quoted 8 lines · On Mon, 29 Jan 2024 15:15:18 +0100 you wrote:
This is the last patchset of a long series of cleanup and preparation to make at803x better maintainable and permit the addition of other QCOM PHY Families.
A shared library modules is created since many QCOM PHY share similar/exact implementation and are reused.
[...]
Here is the summary with links:
- [net-next,v4,1/5] net: phy: move at803x PHY driver to dedicated directory
https://git.kernel.org/netdev/net-next/c/9e56ff53b411 - [net-next,v4,2/5] net: phy: qcom: create and move functions to shared library https://git.kernel.org/netdev/net-next/c/6fb760972c49 - [net-next,v4,3/5] net: phy: qcom: deatch qca83xx PHY driver from at803x https://git.kernel.org/netdev/net-next/c/2e45d404d99d - [net-next,v4,4/5] net: phy: qcom: move additional functions to shared library https://git.kernel.org/netdev/net-next/c/249d2b80e4db - [net-next,v4,5/5] net: phy: qcom: detach qca808x PHY driver from at803x https://git.kernel.org/netdev/net-next/c/c89414adf2ec
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html