arm64: dts: rockchip: add u2phy clock for ehci and ohci of rk3399
Subsystems (2)
PATCH v2 1/1 arm64: dts: rockchip: add u2phy clock for ehci and ohci of rk3399
From: William wu <[email protected]>
We found that the suspend process was blocked when it run into ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci (usb2-phy will be auto suspended if no devices plug-in). and the clk-480m provided by it was disabled if no module used. However, some suspend process related ehci/ohci are base on this clock, so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
---
Changes in v2:
- update the commit message
- remove patches whic add and export the USBPHYx_480M_SRC clock IDs
u2phy ________________
| | |-----> UTMI_CLK ---------> | EHCI |
OSC_24M ---|---> PHY_PLL----|----|
|________^_______| |-----> 480M_CLK ---|G|---> | USBPHY_480M_SRC| ----> USBPHY_480M for SoC
|
|
GRF---
--- arch/arm64/boot/dts/rockchip/rk3399.dtsi | 28 ++++++++++++++++++++-------- 1 file changed, 20 insertions(+), 8 deletions(-)
arch/arm64/boot/dts/rockchip/rk3399.dtsi +20 -8
@@ -315,8 +315,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe380000 0x0 0x20000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy0_host>; phy-names = "usb"; status = "disabled";
@@ -326,8 +328,12 @@ compatible = "generic-ohci"; reg = <0x0 0xfe3a0000 0x0 0x20000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy0_host>; + phy-names = "usb"; status = "disabled"; };
@@ -335,8 +341,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe3c0000 0x0 0x20000>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy1_host>; phy-names = "usb"; status = "disabled";
@@ -346,8 +354,12 @@ compatible = "generic-ohci"; reg = <0x0 0xfe3e0000 0x0 0x20000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy1_host>; + phy-names = "usb"; status = "disabled"; };
Signature · 1 line
2.7.4
PATCH RESEND v2 1/1 arm64: dts: rockchip: add u2phy clock for ehci and ohci of rk3399
From: William wu <[email protected]>
We found that the suspend process was blocked when it run into ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci (usb2-phy will be auto suspended if no devices plug-in). and the clk-480m provided by it was disabled if no module used. However, some suspend process related ehci/ohci are base on this clock, so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
===
u2phy ________________
| | |-----> UTMI_CLK ---------> | EHCI |
OSC_24M ---|---> PHY_PLL----|----|
|________^_______| |-----> 480M_CLK ---|G|---> | USBPHY_480M_SRC| ----> USBPHY_480M for SoC
|
|
GRF===
---
Changes in v2:
- update the commit message
- remove patches whic add and export the USBPHYx_480M_SRC clock IDs
arch/arm64/boot/dts/rockchip/rk3399.dtsi | 28 ++++++++++++++++++++-------- 1 file changed, 20 insertions(+), 8 deletions(-)
arch/arm64/boot/dts/rockchip/rk3399.dtsi +20 -8
@@ -315,8 +315,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe380000 0x0 0x20000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy0_host>; phy-names = "usb"; status = "disabled";
@@ -326,8 +328,12 @@ compatible = "generic-ohci"; reg = <0x0 0xfe3a0000 0x0 0x20000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy0_host>; + phy-names = "usb"; status = "disabled"; };
@@ -335,8 +341,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe3c0000 0x0 0x20000>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy1_host>; phy-names = "usb"; status = "disabled";
@@ -346,8 +354,12 @@ compatible = "generic-ohci"; reg = <0x0 0xfe3e0000 0x0 0x20000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy1_host>; + phy-names = "usb"; status = "disabled"; };
Signature · 1 line
2.7.4
Hi,
Quoted 80 lines · Xing Zheng
From: William wu <[email protected]>
We found that the suspend process was blocked when it run into ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci (usb2-phy will be auto suspended if no devices plug-in). and the clk-480m provided by it was disabled if no module used. However, some suspend process related ehci/ohci are base on this clock, so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
===u2phy ________________ | | |-----> UTMI_CLK ---------> | EHCI | OSC_24M ---|---> PHY_PLL----|----| |________^_______| |-----> 480M_CLK ---|G|---> | USBPHY_480M_SRC| ----> USBPHY_480M for SoC | | GRF===
Signed-off-by William wu <[email protected]>Signed-off-by Xing Zheng <[email protected]>---
Changes in v2:
- update the commit message
- remove patches whic add and export theUSBPHYx_480M_SRCclock IDsarch/arm64/boot/dts/rockchip/rk3399.dtsi | 28 ++++++++++++++++++++-------- 1 file changed, 20 insertions(+), 8 deletions(-)arch/arm64/boot/dts/rockchip/rk3399.dtsi +14
-6@@ -315,8 +315,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe380000 0x0 0x20000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy0_host>; phy-names = "usb"; status = "disabled";@@ -326,8 +328,12 @@ compatible = "generic-ohci"; reg = <0x0 0xfe3a0000 0x0 0x20000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy0_host>; + phy-names = "usb"; status = "disabled"; };@@ -335,8 +341,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe3c0000 0x0 0x20000>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy1_host>; phy-names = "usb"; status = "disabled";@@ -346,8 +354,12 @@ compatible = "generic-ohci";
arch/arm64/boot/dts/rockchip/rk3399.dtsi line 362
Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk3399.dtsi +6
-2reg = <0x0 0xfe3e0000 0x0 0x20000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy1_host>; + phy-names = "usb";
This all looks better to me. From a device tree point of view it makes lots of sense to expose this PHY clock to the controller. Thus:
I can't say that I understand all the interactions between the PHY code and the USB driver, but presumably others have reviewed that more? Offline Heiko pointed me at rockchip_usb2phy_otg_sm_work() which apparently calls rockchip_usb2phy_power_off() and rockchip_usb2phy_power_on() directly sometimes behind the back of the PHY framework. Very strange.
I will also say that there were still some unanswered questions from the previous thread, namely:
A) Heiko: Also, with the change, the ehci will keep the clock (and thus the phy) always on. Does the phy-autosuspend even save anything now?
B) Brian: Is thre a race between power_off() and the delayed work in your USB2 PHY driver?
IMHO neither of those two questions affect the correctness of this
patch: that this clock ought to be provided to the USB Controller. ...but they both are important questions that should be answered.
One other last note is that we probably should be specifying a more specific compatible string, like:
"rk3399-ehci", "generic-ehci"
That will allow us later to use these same device tree files and perhaps deal with the clocks / PHYs in a more efficient way.
-Doug
Hi Doug,
? 2016?12?22? 08:47, Doug Anderson ??:
Quoted 125 lines
Hi,
Quoted 80 lines · Xing Zheng
From: William wu <[email protected]>
We found that the suspend process was blocked when it run into ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci (usb2-phy will be auto suspended if no devices plug-in). and the clk-480m provided by it was disabled if no module used. However, some suspend process related ehci/ohci are base on this clock, so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
===u2phy ________________ | | |-----> UTMI_CLK ---------> | EHCI | OSC_24M ---|---> PHY_PLL----|----| |________^_______| |-----> 480M_CLK ---|G|---> | USBPHY_480M_SRC| ----> USBPHY_480M for SoC | |GRF
===Signed-off-by William wu <[email protected]>Signed-off-by Xing Zheng <[email protected]>---
Changes in v2:
- update the commit message
- remove patches whic add and export theUSBPHYx_480M_SRCclock IDsarch/arm64/boot/dts/rockchip/rk3399.dtsi | 28 ++++++++++++++++++++-------- 1 file changed, 20 insertions(+), 8 deletions(-)arch/arm64/boot/dts/rockchip/rk3399.dtsi +14
-6@@ -315,8 +315,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe380000 0x0 0x20000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy0_host>; phy-names = "usb"; status = "disabled";@@ -326,8 +328,12 @@ compatible = "generic-ohci"; reg = <0x0 0xfe3a0000 0x0 0x20000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy0_host>; + phy-names = "usb"; status = "disabled"; };@@ -335,8 +341,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe3c0000 0x0 0x20000>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy1_host>; phy-names = "usb"; status = "disabled";@@ -346,8 +354,12 @@ compatible = "generic-ohci";arch/arm64/boot/dts/rockchip/rk3399.dtsi line 362
Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk3399.dtsi +6
-2reg = <0x0 0xfe3e0000 0x0 0x20000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy1_host>; + phy-names = "usb";This all looks better to me. From a device tree point of view it makes lots of sense to expose this PHY clock to the controller. Thus:
Reviewed-by Douglas Anderson <[email protected]>I can't say that I understand all the interactions between the PHY code and the USB driver, but presumably others have reviewed that more? Offline Heiko pointed me at
rockchip_usb2phy_otg_sm_work()which apparently callsrockchip_usb2phy_power_off()androckchip_usb2phy_power_on()directly sometimes behind the back of the PHY framework. Very strange.I will also say that there were still some unanswered questions from the previous thread, namely:
A) Heiko: Also, with the change, the ehci will keep the clock (and thus the phy) always on. Does the phy-autosuspend even save anything now?
B) Brian: Is thre a race between
power_off()and the delayed work in your USB2 PHY driver?IMHO neither of those two questions affect the correctness of this
patch: that this clock ought to be provided to the USB Controller. ...but they both are important questions that should be answered.One other last note is that we probably should be specifying a more specific compatible string, like:
Quoted 8 lines
"rk3399-ehci", "generic-ehci"That will allow us later to use these same device tree files and perhaps deal with the clocks / PHYs in a more efficient way.
-Doug
I will *ping* Frank and William to answer your questions until they finish the business travel.
Thanks.
Signature · 1 line
- Xing Zheng
Dear Doug & Xing Zheng,
? 2016?12?22? 08:47, Doug Anderson ??:
Quoted 11 lines
Hi,
Quoted 8 lines · Xing Zheng
From: William wu <[email protected]>
We found that the suspend process was blocked when it run into ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci (usb2-phy will be auto suspended if no devices plug-in). and the clk-480m provided by it was disabled if no module used. However,
I suggest that change the "clk-480m" to "utmi clock" here.
Quoted 88 lines
Quoted 72 lines
some suspend process related ehci/ohci are base on this clock, so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
===u2phy ________________ | | |-----> UTMI_CLK ---------> | EHCI | OSC_24M ---|---> PHY_PLL----|----| |________^_______| |-----> 480M_CLK ---|G|---> | USBPHY_480M_SRC| ----> USBPHY_480M for SoC | |GRF
===Signed-off-by William wu <[email protected]>Signed-off-by Xing Zheng <[email protected]>---
Changes in v2:
- update the commit message
- remove patches whic add and export theUSBPHYx_480M_SRCclock IDsarch/arm64/boot/dts/rockchip/rk3399.dtsi | 28 ++++++++++++++++++++-------- 1 file changed, 20 insertions(+), 8 deletions(-)arch/arm64/boot/dts/rockchip/rk3399.dtsi +14
-6@@ -315,8 +315,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe380000 0x0 0x20000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy0_host>; phy-names = "usb"; status = "disabled";@@ -326,8 +328,12 @@ compatible = "generic-ohci"; reg = <0x0 0xfe3a0000 0x0 0x20000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; - clock-names = "hclk_host0", "hclk_host0_arb"; + clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>, + <&u2phy0>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy0_host>; + phy-names = "usb"; status = "disabled"; };@@ -335,8 +341,10 @@ compatible = "generic-ehci"; reg = <0x0 0xfe3c0000 0x0 0x20000>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; phys = <&u2phy1_host>; phy-names = "usb"; status = "disabled";@@ -346,8 +354,12 @@ compatible = "generic-ohci";arch/arm64/boot/dts/rockchip/rk3399.dtsi line 362
Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk3399.dtsi +6
-2reg = <0x0 0xfe3e0000 0x0 0x20000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; - clock-names = "hclk_host1", "hclk_host1_arb"; + clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>, + <&u2phy1>; + clock-names = "usbhost", "arbiter", + "utmi"; + phys = <&u2phy1_host>; + phy-names = "usb";This all looks better to me. From a device tree point of view it makes lots of sense to expose this PHY clock to the controller. Thus:
Reviewed-by Douglas Anderson <[email protected]>
Quoted 6 lines
I can't say that I understand all the interactions between the PHY code and the USB driver, but presumably others have reviewed that more? Offline Heiko pointed me at
rockchip_usb2phy_otg_sm_work()which apparently callsrockchip_usb2phy_power_off()androckchip_usb2phy_power_on()directly sometimes behind the back of the PHY framework. Very strange.
Yes, the rockchip_usb2phy_otg_sm_work() in the USB2 PHY driver and EHCI/OHCI platform
driver via the PHY framework can both do phy power on/off. We do that because we want
to reduce USB2 PHY consumption in system runtime and deep sleep.
For EHCI/OHCI platform drivers, they call phy_power_on() in probe to power on USB2 PHY,
and don't power off USB2 PHY in system runtime, even if there's no USB2 device connected.
They just call phy_power_off() in PM suspend, and call phy_power_on() in PM resume to
power on USB2 PHY again. AKA the EHCI/OHCI platform driver can only support USB power
management in deep sleep.
So we add a work in USB2 PHY driver to manage USB2 PHY power. The work scheduled every
60 seconds, check the USB D+/D- and disconnect status in GRF registers to know if any USB
device connected. If no USB connected, it will call rockchip_usb2phy_power_off() to power
off USB2 PHY. And also, the USB2 PHY driver use an irq to detect D+/D- voltage when USB
device connected? and then call rockchip_usb2phy_power_on() to power on USB2 PHY.
AKA the work is used to support USB PHY power management in runtime.
Quoted 8 lines
I will also say that there were still some unanswered questions from the previous thread, namely:
A) Heiko: Also, with the change, the ehci will keep the clock (and thus the phy) always on. Does the phy-autosuspend even save anything now?
With this patch, the GRF USB commonon will always enable in system runtime. But we still
can set USB2 PHY enter suspend mode by power down most of PHY logic module via GRF,
so the phy-autosuspend is still useful.
On the other hand, commonon bit is used for PLL clock logical, its power consumption is
not big in theory, I remember that I tested on the other SoC? the commonon bit consumed
about 1~2mA.
Quoted 2 lines
B) Brian: Is thre a race between
power_off()and the delayed work in your USB2 PHY driver?
I'm not clear understand the race mentioned here.
IMO, PHY framework power_off() and work rockchip_usb2phy_power_off() don't have race
problem.
And maybe there is a race between PHY framework power_off() and the delayed workrockchip_usb2phy_power_on() in USB2 PHY driver, but I think the probability is low?
the race case maybe?
1. EHCI/OHCI platform call phy_power_off() in PM suspend;
2. Plug in an USB device after USB2 PHY has entered suspend;
3. Power on USB2 PHY again in work;
4. After these, finally the USB2 PHY is power on when system enter sleep.
Quoted 19 lines
IMHO neither of those two questions affect the correctness of this
patch: that this clock ought to be provided to the USB Controller. ...but they both are important questions that should be answered.One other last note is that we probably should be specifying a more specific compatible string, like:
"rk3399-ehci", "generic-ehci"That will allow us later to use these same device tree files and perhaps deal with the clocks / PHYs in a more efficient way.
-Doug
Heiko Stuebner
maintainerAm Mittwoch, 21. Dezember 2016, 18:41:05 CET schrieb Xing Zheng:
Quoted 19 lines
From: William wu <[email protected]>
We found that the suspend process was blocked when it run into ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci (usb2-phy will be auto suspended if no devices plug-in). and the clk-480m provided by it was disabled if no module used. However, some suspend process related ehci/ohci are base on this clock, so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
===u2phy ________________ | | |-----> UTMI_CLK ---------> | EHCI |
OSC_24M---|---> PHY_PLL----|----|
Quoted 7 lines
|________^_______| |-----> 480M_CLK ---|G|---> | |USBPHY_480M_SRC| ----> USBPHY_480M for SoCGRF
===Signed-off-by William wu <[email protected]>Signed-off-by Xing Zheng <[email protected]>
applied for 4.11 with Doug's Review-tag
Thanks
Heiko