Skip to contentSkip to conversation

Bluetooth: Introduce HCI Driver protocol

PATCH In review Hsin-chen Chuang 3 participants 6 messages Apr 16, 2025

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/4 Bluetooth: Introduce HCI Driver protocol

From: Hsin-chen Chuang <[email protected]>

Although commit 75ddcd5ad40e ("Bluetooth: btusb: Configure altsetting for HCI_USER_CHANNEL") has enabled the HCI_USER_CHANNEL user to send out SCO data through USB Bluetooth chips, it's observed that with the patch HFP is flaky on most of the existing USB Bluetooth controllers: Intel chips sometimes send out no packet for Transparent codec; MTK chips may generate SCO data with a wrong handle for CVSD codec; RTK could split the data with a wrong packet size for Transparent codec; ... etc.

To address the issue above one needs to reset the altsetting back to zero when there is no active SCO connection, which is the same as the BlueZ behavior, and another benefit is the bus doesn't need to reserve bandwidth when no SCO connection.

This patch adds the infrastructure that allow the user space program to talk to Bluetooth drivers directly:
- Define the new packet type HCI_DRV_PKT which is specifically used for communication between the user space program and the Bluetooth drviers
- hci_send_frame intercepts the packets and invokes drivers' HCI Drv callbacks (so far only defined for btusb)
- 2 kinds of events to user space: Command Status and Command Complete, the former simply returns the status while the later may contain additional response data.

Fixes b16b327edb4d ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")

---

Changes in v2:
- Specifying drvier specific commands by hci_opcode_ogf

 drivers/bluetooth/btusb.c        |  69 ++++++++++++++++++--
 include/net/bluetooth/hci.h      |   1 +
 include/net/bluetooth/hci_core.h |   3 +
 include/net/bluetooth/hci_drv.h  |  76 ++++++++++++++++++++++
 include/net/bluetooth/hci_mon.h  |   2 +
 net/bluetooth/Makefile           |   3 +-
 net/bluetooth/hci_core.c         |  10 +++
 net/bluetooth/hci_drv.c          | 104 +++++++++++++++++++++++++++++++
 net/bluetooth/hci_sock.c         |  12 +++-
 9 files changed, 271 insertions(+), 9 deletions(-)
 create mode 100644 include/net/bluetooth/hci_drv.h
 create mode 100644 net/bluetooth/hci_drv.c
drivers/bluetooth/btusb.c +63 -6
index 7a9b89bcea22..79a944cdb662 100644
@@ -21,6 +21,7 @@
 
 #include <net/bluetooth/bluetooth.h>
 #include <net/bluetooth/hci_core.h>
+#include <net/bluetooth/hci_drv.h>
 
 #include "btintel.h"
 #include "btbcm.h"
@@ -3754,6 +3755,61 @@ static ssize_t isoc_alt_store(struct device *dev,
 
 static DEVICE_ATTR_RW(isoc_alt);
 
+static const struct {
+	u16 opcode;
+	const char *desc;
+} btusb_hci_drv_supported_commands[] = {
+	/* Common commands */
+	{ HCI_DRV_OP_READ_INFO, "Read Info" },
+};
+static int btusb_hci_drv_read_info(struct hci_dev *hdev, void *data,
+				   u16 data_len)
+{
+	struct hci_drv_rp_read_info *rp;
+	size_t rp_size;
+	int err, i;
+	u16 opcode, num_supported_commands =
+		ARRAY_SIZE(btusb_hci_drv_supported_commands);
+
+	rp_size = sizeof(*rp) + num_supported_commands * 2;
+
+	rp = kmalloc(rp_size, GFP_KERNEL);
+	if (!rp)
+		return -ENOMEM;
+
+	strscpy_pad(rp->driver_name, btusb_driver.name);
+
+	rp->num_supported_commands = cpu_to_le16(num_supported_commands);
+	for (i = 0; i < num_supported_commands; i++) {
+		opcode = btusb_hci_drv_supported_commands[i].opcode;
+		bt_dev_info(hdev,
+			    "Supported HCI Drv command (0x%02x|0x%04x): %s",
+			    hci_opcode_ogf(opcode),
+			    hci_opcode_ocf(opcode),
+			    btusb_hci_drv_supported_commands[i].desc);
+		rp->supported_commands[i] = cpu_to_le16(opcode);
+	}
+
+	err = hci_drv_cmd_complete(hdev, HCI_DRV_OP_READ_INFO,
+				   HCI_DRV_STATUS_SUCCESS, rp, rp_size);
+
+	kfree(rp);
+	return err;
+}
+
+static const struct hci_drv_handler btusb_hci_drv_common_handlers[] = {
+	{ btusb_hci_drv_read_info,	HCI_DRV_READ_INFO_SIZE },
+};
+
+static const struct hci_drv_handler btusb_hci_drv_specific_handlers[] = {};
+
+static struct hci_drv btusb_hci_drv = {
+	.common_handler_count	= ARRAY_SIZE(btusb_hci_drv_common_handlers),
+	.common_handlers	= btusb_hci_drv_common_handlers,
+	.specific_handler_count	= ARRAY_SIZE(btusb_hci_drv_specific_handlers),
+	.specific_handlers	= btusb_hci_drv_specific_handlers,
+};
+
 static int btusb_probe(struct usb_interface *intf,
 		       const struct usb_device_id *id)
 {
@@ -3893,12 +3949,13 @@ static int btusb_probe(struct usb_interface *intf,
 		data->reset_gpio = reset_gpio;
 	}
 
-	hdev->open   = btusb_open;
-	hdev->close  = btusb_close;
-	hdev->flush  = btusb_flush;
-	hdev->send   = btusb_send_frame;
-	hdev->notify = btusb_notify;
-	hdev->wakeup = btusb_wakeup;
+	hdev->open    = btusb_open;
+	hdev->close   = btusb_close;
+	hdev->flush   = btusb_flush;
+	hdev->send    = btusb_send_frame;
+	hdev->notify  = btusb_notify;
+	hdev->wakeup  = btusb_wakeup;
+	hdev->hci_drv = &btusb_hci_drv;
 
 #ifdef CONFIG_PM
 	err = btusb_config_oob_wake(hdev);
include/net/bluetooth/hci.h +1 -0
index a8586c3058c7..e297b312d2b7 100644
@@ -494,6 +494,7 @@ enum {
 #define HCI_EVENT_PKT		0x04
 #define HCI_ISODATA_PKT		0x05
 #define HCI_DIAG_PKT		0xf0
+#define HCI_DRV_PKT		0xf1
 #define HCI_VENDOR_PKT		0xff
 
 /* HCI packet types */
include/net/bluetooth/hci_core.h +3 -0
index 5115da34f881..dd80f1a398be 100644
@@ -31,6 +31,7 @@
 #include <linux/rculist.h>
 
 #include <net/bluetooth/hci.h>
+#include <net/bluetooth/hci_drv.h>
 #include <net/bluetooth/hci_sync.h>
 #include <net/bluetooth/hci_sock.h>
 #include <net/bluetooth/coredump.h>
@@ -613,6 +614,8 @@ struct hci_dev {
 	struct list_head	monitored_devices;
 	bool			advmon_pend_notify;
 
+	struct hci_drv		*hci_drv;
+
 #if IS_ENABLED(CONFIG_BT_LEDS)
 	struct led_trigger	*power_led;
 #endif
include/net/bluetooth/hci_drv.h new file +76 -0

76 lines not on this page · raw message

include/net/bluetooth/hci_mon.h +2 -0
index 082f89531b88..bbd752494ef9 100644
@@ -51,6 +51,8 @@ struct hci_mon_hdr {
 #define HCI_MON_CTRL_EVENT	17
 #define HCI_MON_ISO_TX_PKT	18
 #define HCI_MON_ISO_RX_PKT	19
+#define HCI_MON_DRV_TX_PKT	20
+#define HCI_MON_DRV_RX_PKT	21
 
 struct hci_mon_new_index {
 	__u8		type;
net/bluetooth/Makefile +2 -1
index 5a3835b7dfcd..a7eede7616d8 100644
@@ -14,7 +14,8 @@ bluetooth_6lowpan-y := 6lowpan.o
 
 bluetooth-y := af_bluetooth.o hci_core.o hci_conn.o hci_event.o mgmt.o \
 	hci_sock.o hci_sysfs.o l2cap_core.o l2cap_sock.o smp.o lib.o \
-	ecdh_helper.o mgmt_util.o mgmt_config.o hci_codec.o eir.o hci_sync.o
+	ecdh_helper.o mgmt_util.o mgmt_config.o hci_codec.o eir.o hci_sync.o \
+	hci_drv.o
 
 bluetooth-$(CONFIG_DEV_COREDUMP) += coredump.o
 
net/bluetooth/hci_core.c +10 -0
index 5eb0600bbd03..2815b2d7d28d 100644
@@ -2911,6 +2911,8 @@ int hci_recv_frame(struct hci_dev *hdev, struct sk_buff *skb)
 		break;
 	case HCI_ISODATA_PKT:
 		break;
+	case HCI_DRV_PKT:
+		break;
 	default:
 		kfree_skb(skb);
 		return -EINVAL;
@@ -3019,6 +3021,14 @@ static int hci_send_frame(struct hci_dev *hdev, struct sk_buff *skb)
 		return -EINVAL;
 	}
 
+	if (hci_skb_pkt_type(skb) == HCI_DRV_PKT) {
+		// Intercept HCI Drv packet here and don't go with hdev->send
+		// callabck.
+		err = hci_drv_process_cmd(hdev, skb);
+		kfree_skb(skb);
+		return err;
+	}
+
 	err = hdev->send(hdev, skb);
 	if (err < 0) {
 		bt_dev_err(hdev, "sending frame failed (%d)", err);
net/bluetooth/hci_drv.c new file +104 -0

104 lines not on this page · raw message

net/bluetooth/hci_sock.c +10 -2
index 022b86797acd..428ee5c7de7e 100644
@@ -234,7 +234,8 @@ void hci_send_to_sock(struct hci_dev *hdev, struct sk_buff *skb)
 			if (hci_skb_pkt_type(skb) != HCI_EVENT_PKT &&
 			    hci_skb_pkt_type(skb) != HCI_ACLDATA_PKT &&
 			    hci_skb_pkt_type(skb) != HCI_SCODATA_PKT &&
-			    hci_skb_pkt_type(skb) != HCI_ISODATA_PKT)
+			    hci_skb_pkt_type(skb) != HCI_ISODATA_PKT &&
+			    hci_skb_pkt_type(skb) != HCI_DRV_PKT)
 				continue;
 		} else {
 			/* Don't send frame to other channel types */
@@ -391,6 +392,12 @@ void hci_send_to_monitor(struct hci_dev *hdev, struct sk_buff *skb)
 		else
 			opcode = cpu_to_le16(HCI_MON_ISO_TX_PKT);
 		break;
+	case HCI_DRV_PKT:
+		if (bt_cb(skb)->incoming)
+			opcode = cpu_to_le16(HCI_MON_DRV_RX_PKT);
+		else
+			opcode = cpu_to_le16(HCI_MON_DRV_TX_PKT);
+		break;
 	case HCI_DIAG_PKT:
 		opcode = cpu_to_le16(HCI_MON_VENDOR_DIAG);
 		break;
@@ -1860,7 +1867,8 @@ static int hci_sock_sendmsg(struct socket *sock, struct msghdr *msg,
 		if (hci_skb_pkt_type(skb) != HCI_COMMAND_PKT &&
 		    hci_skb_pkt_type(skb) != HCI_ACLDATA_PKT &&
 		    hci_skb_pkt_type(skb) != HCI_SCODATA_PKT &&
-		    hci_skb_pkt_type(skb) != HCI_ISODATA_PKT) {
+		    hci_skb_pkt_type(skb) != HCI_ISODATA_PKT &&
+		    hci_skb_pkt_type(skb) != HCI_DRV_PKT) {
 			err = -EINVAL;
 			goto drop;
 		}
Signature · 1 line
2.49.0.604.gff1f9ca942-goog
#1 lore raw

PATCH v2 2/4 Bluetooth: btusb: Add HCI Drv commands for configuring altsetting

From: Hsin-chen Chuang <[email protected]>

Although commit 75ddcd5ad40e ("Bluetooth: btusb: Configure altsetting for HCI_USER_CHANNEL") has enabled the HCI_USER_CHANNEL user to send out SCO data through USB Bluetooth chips, it's observed that with the patch HFP is flaky on most of the existing USB Bluetooth controllers: Intel chips sometimes send out no packet for Transparent codec; MTK chips may generate SCO data with a wrong handle for CVSD codec; RTK could split the data with a wrong packet size for Transparent codec; ... etc.

To address the issue above one needs to reset the altsetting back to zero when there is no active SCO connection, which is the same as the BlueZ behavior, and another benefit is the bus doesn't need to reserve bandwidth when no SCO connection.

This patch adds "Supported Altsettings" and "Switch Altsetting" commands that allow the user space program to configure the altsetting freely.

This patch is tested on ChromeOS devices. The USB Bluetooth models (CVSD, TRANS alt3, and TRANS alt6) could pass the stress HFP test narrow band speech and wide band speech.

Fixes b16b327edb4d ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")

---

(no changes since v1)

 drivers/bluetooth/btusb.c | 72 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 71 insertions(+), 1 deletion(-)
drivers/bluetooth/btusb.c +71 -1
index 79a944cdb662..a16ca3128ac7 100644
@@ -3755,12 +3755,31 @@ static ssize_t isoc_alt_store(struct device *dev,
 
 static DEVICE_ATTR_RW(isoc_alt);
 
+#define BTUSB_HCI_DRV_OP_SUPPORTED_ALTSETTINGS \
+		hci_opcode_pack(HCI_DRV_OGF_DRIVER_SPECIFIC, 0x0000)
+#define BTUSB_HCI_DRV_SUPPORTED_ALTSETTINGS_SIZE	0
+struct btusb_hci_drv_rp_supported_altsettings {
+	__u8	num_supported_altsettings;
+	__u8	supported_altsettings[];
+} __packed;
+
+#define BTUSB_HCI_DRV_OP_SWITCH_ALTSETTING \
+		hci_opcode_pack(HCI_DRV_OGF_DRIVER_SPECIFIC, 0x0001)
+#define BTUSB_HCI_DRV_SWITCH_ALTSETTING_SIZE		1
+struct btusb_hci_drv_cmd_switch_altsetting {
+	__u8	new_altsetting;
+} __packed;
+
 static const struct {
 	u16 opcode;
 	const char *desc;
 } btusb_hci_drv_supported_commands[] = {
 	/* Common commands */
 	{ HCI_DRV_OP_READ_INFO, "Read Info" },
+
+	/* Driver specific commands */
+	{ BTUSB_HCI_DRV_OP_SUPPORTED_ALTSETTINGS, "Supported Altsettings" },
+	{ BTUSB_HCI_DRV_OP_SWITCH_ALTSETTING,     "Switch Altsetting" },
 };
 static int btusb_hci_drv_read_info(struct hci_dev *hdev, void *data,
 				   u16 data_len)
@@ -3797,11 +3816,62 @@ static int btusb_hci_drv_read_info(struct hci_dev *hdev, void *data,
 	return err;
 }
 
+static int btusb_hci_drv_supported_altsettings(struct hci_dev *hdev, void *data,
+					       u16 data_len)
+{
+	struct btusb_data *drvdata = hci_get_drvdata(hdev);
+	struct btusb_hci_drv_rp_supported_altsettings *rp;
+	size_t rp_size;
+	int err;
+	u8 i;
+
+	/* There are at most 7 alt (0 - 6) */
+	rp = kmalloc(sizeof(*rp) + 7, GFP_KERNEL);
+
+	rp->num_supported_altsettings = 0;
+	if (drvdata->isoc)
+		for (i = 0; i <= 6; i++)
+			if (btusb_find_altsetting(drvdata, i))
+				rp->supported_altsettings[
+					rp->num_supported_altsettings++] = i;
+
+	rp_size = sizeof(*rp) + rp->num_supported_altsettings;
+
+	err = hci_drv_cmd_complete(hdev, BTUSB_HCI_DRV_OP_SUPPORTED_ALTSETTINGS,
+				   HCI_DRV_STATUS_SUCCESS, rp, rp_size);
+	kfree(rp);
+	return err;
+}
+
+static int btusb_hci_drv_switch_altsetting(struct hci_dev *hdev, void *data,
+					   u16 data_len)
+{
+	struct btusb_hci_drv_cmd_switch_altsetting *cmd = data;
+	u8 status;
+
+	if (cmd->new_altsetting > 6) {
+		status = HCI_DRV_STATUS_INVALID_PARAMETERS;
+	} else {
+		if (btusb_switch_alt_setting(hdev, cmd->new_altsetting))
+			status = HCI_DRV_STATUS_UNSPECIFIED_ERROR;
+		else
+			status = HCI_DRV_STATUS_SUCCESS;
+	}
+
+	return hci_drv_cmd_status(hdev, BTUSB_HCI_DRV_OP_SWITCH_ALTSETTING,
+				  status);
+}
+
 static const struct hci_drv_handler btusb_hci_drv_common_handlers[] = {
 	{ btusb_hci_drv_read_info,	HCI_DRV_READ_INFO_SIZE },
 };
 
-static const struct hci_drv_handler btusb_hci_drv_specific_handlers[] = {};
+static const struct hci_drv_handler btusb_hci_drv_specific_handlers[] = {
+	{ btusb_hci_drv_supported_altsettings,
+				BTUSB_HCI_DRV_SUPPORTED_ALTSETTINGS_SIZE },
+	{ btusb_hci_drv_switch_altsetting,
+				BTUSB_HCI_DRV_SWITCH_ALTSETTING_SIZE },
+};
 
 static struct hci_drv btusb_hci_drv = {
 	.common_handler_count	= ARRAY_SIZE(btusb_hci_drv_common_handlers),
Signature · 1 line
2.49.0.604.gff1f9ca942-goog
#2 lore raw

PATCH v2 3/4 Revert "Bluetooth: btusb: Configure altsetting for HCI_USER_CHANNEL"

In reply to Hsin-chen Chuang

From: Hsin-chen Chuang <[email protected]>

This reverts commit 75ddcd5ad40ecd9fbc9f5a7a2ed0e1e74921db3c.

This patch doesn't work quite well - It's observed that with this patch HFP is flaky on most of the existing USB Bluetooth controllers: Intel chips sometimes send out no packet for Transparent codec; MTK chips may generate SCO data with a wrong handle for CVSD codec; RTK could split the data with a wrong packet size for Transparent codec; ... etc.

---

(no changes since v1)

 drivers/bluetooth/Kconfig | 12 ------------
 drivers/bluetooth/btusb.c | 41 ---------------------------------------
 2 files changed, 53 deletions(-)
drivers/bluetooth/Kconfig +0 -12
index 7771edf54fb3..4ab32abf0f48 100644
@@ -56,18 +56,6 @@ config BT_HCIBTUSB_POLL_SYNC
 	  Say Y here to enable USB poll_sync for Bluetooth USB devices by
 	  default.
 
-config BT_HCIBTUSB_AUTO_ISOC_ALT
-	bool "Automatically adjust alternate setting for Isoc endpoints"
-	depends on BT_HCIBTUSB
-	default y if CHROME_PLATFORMS
-	help
-	  Say Y here to automatically adjusting the alternate setting for
-	  HCI_USER_CHANNEL whenever a SCO link is established.
-
-	  When enabled, btusb intercepts the HCI_EV_SYNC_CONN_COMPLETE packets
-	  and configures isoc endpoint alternate setting automatically when
-	  HCI_USER_CHANNEL is in use.
-
 config BT_HCIBTUSB_BCM
 	bool "Broadcom protocol support"
 	depends on BT_HCIBTUSB
drivers/bluetooth/btusb.c +0 -41

59 lines not on this page · raw message

Signature · 1 line
2.49.0.604.gff1f9ca942-goog
#3 lore raw

PATCH v2 4/4 Revert "Bluetooth: btusb: add sysfs attribute to control USB alt setting"

In reply to Hsin-chen Chuang

From: Hsin-chen Chuang <[email protected]>

This reverts commit b16b327edb4d030fb4c8fe38c7d299074d47ee3f.

The sysfs node introduced by this patch could potentially race with user space. The original motivation - Support configuring altsetting from the user space will be added by another series.

---

(no changes since v1)

 drivers/bluetooth/btusb.c | 34 +---------------------------------
 1 file changed, 1 insertion(+), 33 deletions(-)
drivers/bluetooth/btusb.c +1 -33
index 937d69684df8..5fa75a777a71 100644
@@ -3688,32 +3688,6 @@ static const struct file_operations force_poll_sync_fops = {
 	.llseek		= default_llseek,
 };
 
-static ssize_t isoc_alt_show(struct device *dev,
-			     struct device_attribute *attr,
-			     char *buf)
-{
-	struct btusb_data *data = dev_get_drvdata(dev);
-
-	return sysfs_emit(buf, "%d\n", data->isoc_altsetting);
-}
-
-static ssize_t isoc_alt_store(struct device *dev,
-			      struct device_attribute *attr,
-			      const char *buf, size_t count)
-{
-	struct btusb_data *data = dev_get_drvdata(dev);
-	int alt;
-	int ret;
-
-	if (kstrtoint(buf, 10, &alt))
-		return -EINVAL;
-
-	ret = btusb_switch_alt_setting(data->hdev, alt);
-	return ret < 0 ? ret : count;
-}
-
-static DEVICE_ATTR_RW(isoc_alt);
-
 #define BTUSB_HCI_DRV_OP_SUPPORTED_ALTSETTINGS \
 		hci_opcode_pack(HCI_DRV_OGF_DRIVER_SPECIFIC, 0x0000)
 #define BTUSB_HCI_DRV_SUPPORTED_ALTSETTINGS_SIZE	0
@@ -4203,10 +4177,6 @@ static int btusb_probe(struct usb_interface *intf,
 						 data->isoc, data);
 		if (err < 0)
 			goto out_free_dev;
-
-		err = device_create_file(&intf->dev, &dev_attr_isoc_alt);
-		if (err)
-			goto out_free_dev;
 	}
 
 	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) && data->diag) {
@@ -4253,10 +4223,8 @@ static void btusb_disconnect(struct usb_interface *intf)
 	hdev = data->hdev;
 	usb_set_intfdata(data->intf, NULL);
 
-	if (data->isoc) {
-		device_remove_file(&intf->dev, &dev_attr_isoc_alt);
+	if (data->isoc)
 		usb_set_intfdata(data->isoc, NULL);
-	}
 
 	if (data->diag)
 		usb_set_intfdata(data->diag, NULL);
Signature · 1 line
2.49.0.604.gff1f9ca942-goog
#4 lore raw
In reply to Hsin-chen Chuang

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list. This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=953913

---Test result---

Test Summary:

CheckPatch                    PENDING   0.43 seconds
GitLint                       PENDING   0.33 seconds
SubjectPrefix                 PASS      3.42 seconds
BuildKernel                   PASS      25.58 seconds
CheckAllWarning               PASS      28.36 seconds
CheckSparse                   PASS      40.61 seconds
BuildKernel32                 PASS      32.78 seconds
TestRunnerSetup               PASS      484.26 seconds
TestRunner_l2cap-tester       PASS      22.46 seconds
TestRunner_iso-tester         PASS      37.98 seconds
TestRunner_bnep-tester        PASS      4.95 seconds
TestRunner_mgmt-tester        FAIL      126.63 seconds
TestRunner_rfcomm-tester      PASS      8.44 seconds
TestRunner_sco-tester         PASS      28.71 seconds
TestRunner_ioctl-tester       PASS      8.94 seconds
TestRunner_mesh-tester        PASS      6.37 seconds
TestRunner_smp-tester         PASS      7.56 seconds
TestRunner_userchan-tester    PASS      7.87 seconds
IncrementalBuild              PENDING   0.64 seconds

Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script Output:

##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:

##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner Output:
Total: 490, Passed: 485 (99.0%), Failed: 1, Not Run: 4

Failed Test Cases
LL Privacy - Set Flags 3 (2 Devices to RL) Failed 0.180 seconds
##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series Output:

---
Regards,
Linux Bluetooth

#5 lore raw
In reply to Hsin-chen Chuang
This series was applied to bluetooth/bluetooth-next.git (master) by Luiz Augusto von Dentz <[email protected]>:

Hello:

This series was applied to bluetooth/bluetooth-next.git (master) by Luiz Augusto von Dentz <[email protected]>:

Quoted 11 lines · On Wed, 16 Apr 2025 09:53:35 +0000 you wrote:

From: Hsin-chen Chuang <[email protected]>

Although commit 75ddcd5ad40e ("Bluetooth: btusb: Configure altsetting for HCI_USER_CHANNEL") has enabled the HCI_USER_CHANNEL user to send out SCO data through USB Bluetooth chips, it's observed that with the patch HFP is flaky on most of the existing USB Bluetooth controllers: Intel chips sometimes send out no packet for Transparent codec; MTK chips may generate SCO data with a wrong handle for CVSD codec; RTK could split the data with a wrong packet size for Transparent codec; ... etc.

[...]

Here is the summary with links:
- [v2,1/4] Bluetooth: Introduce HCI Driver protocol
(no matching commit)
- [v2,2/4] Bluetooth: btusb: Add HCI Drv commands for configuring altsetting (no matching commit)
- [v2,3/4] Revert "Bluetooth: btusb: Configure altsetting for HCI_USER_CHANNEL"

    https://git.kernel.org/bluetooth/bluetooth-next/c/3947fa617367
  - [v2,4/4] Revert "Bluetooth: btusb: add sysfs attribute to control USB alt setting"
    https://git.kernel.org/bluetooth/bluetooth-next/c/79f21135b7b0

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html