Skip to contentSkip to conversation

ARM: dts: qcom: msm8974-samsung-hlte: Add touchkey support

PATCH Applied Luca Weiss 3 participants 3 messages Jun 18, 2025 – Aug 11, 2025

Subsystems (3)
lore
Share & tools
lore

Luca Weiss

author
#0 lore raw

PATCH v2 1/1 ARM: dts: qcom: msm8974-samsung-hlte: Add touchkey support

From: Adam Honse <[email protected]>

Add support for the touchkeys on the Samsung Galaxy Note 3 (hlte).

---
Changes in v2:
- Fix schema validation failure, adjust i2c-gpio node name
- Fix misplaced S-o-b (hopefully)
- Link to v1: https://lore.kernel.org/r/[email protected]

---
 .../boot/dts/qcom/qcom-msm8974-samsung-hlte.dts    | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
arch/arm/boot/dts/qcom/qcom-msm8974-samsung-hlte.dts +45 -0
index 903bb4d125135771504281df50aa11c9b6576a28..b7a1367d3470551de12af699ef150434dc0302b8 100644
@@ -50,6 +50,34 @@ key-volume-up {
 		};
 	};
 
+	i2c-touchkey {
+		compatible = "i2c-gpio";
+
+		sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+		pinctrl-0 = <&i2c_touchkey_pins>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "cypress,midas-touchkey";
+			reg = <0x20>;
+
+			interrupts-extended = <&pm8941_gpios 29 IRQ_TYPE_EDGE_FALLING>;
+
+			pinctrl-0 = <&touchkey_pin>;
+			pinctrl-names = "default";
+
+			vcc-supply = <&pm8941_lvs3>;
+			vdd-supply = <&pm8941_l13>;
+
+			linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+		};
+	};
+
 	touch_ldo: regulator-touch {
 		compatible = "regulator-fixed";
 		regulator-name = "touch-ldo";
@@ -149,6 +177,14 @@ touch_ldo_pin: touchscreen-ldo-state {
 		power-source = <PM8941_GPIO_S3>;
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
 	};
+
+	touchkey_pin: touchkey-int-state {
+		pins = "gpio29";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PM8941_GPIO_S3>;
+	};
 };
 
 &remoteproc_adsp {
@@ -332,6 +368,9 @@ pm8941_l24: l24 {
 			regulator-min-microvolt = <3075000>;
 			regulator-max-microvolt = <3075000>;
 		};
+
+		pm8941_lvs1: lvs1 {};
+		pm8941_lvs3: lvs3 {};
 	};
 };
 
@@ -378,6 +417,12 @@ sdhc3_pin_a: sdhc3-pin-active-state {
 		drive-strength = <8>;
 		bias-disable;
 	};
+
+	i2c_touchkey_pins: i2c-touchkey-state {
+		pins = "gpio95", "gpio96";
+		function = "gpio";
+		bias-pull-up;
+	};
 };
 
 &usb {

---
base-commit: e04c78d86a9699d136910cfc0bdcf01087e3267e
change-id: 20250419-hlte-touchkey-8ea2f37a0795

Best regards,

Signature · 1 line
Luca Weiss <[email protected]>
Reviewed-by on v2 1/1
#1 lore raw
Quoted 4 lines · Luca Weiss

From: Adam Honse <[email protected]>

Add support for the touchkeys on the Samsung Galaxy Note 3 (hlte).

Quoted 8 lines

---
Changes in v2:
- Fix schema validation failure, adjust i2c-gpio node name
- Fix misplaced S-o-b (hopefully)
- Link to v1: https://lore.kernel.org/r/[email protected]
---

Konrad

maintainer Applied
#2 lore raw
In reply to Luca Weiss
Quoted 3 lines · Luca Weiss

Add support for the touchkeys on the Samsung Galaxy Note 3 (hlte).

Applied, thanks!

[1/1] ARM: dts: qcom: msm8974-samsung-hlte: Add touchkey support

      commit: 9da3f7add96708103c4cf1817d4bda97ea12b1d4

Best regards,

Signature · 1 line
Bjorn Andersson <[email protected]>