Skip to contentSkip to conversation

Support for ASUS egpu, dpgu disable, panel overdrive

PATCH In review Luke D. Jones 4 participants 14 messages Jul 4, 2021 – Jul 16, 2021

Subsystems (2)
lore
Share & tools
lore

Luke D. Jones

author maintainer
#0 lore raw

cover Support for ASUS egpu, dpgu disable, panel overdrive

This patch series adds support for some functions that are found on newer ASUS gaming laptops:

- Panel overdrive: Some laptops can drive the LCD matrix slightly faster to eliminate or reduce ghosting artifacts

- dGPU disable: ASUS added a function in ACPI to disable or enable the dGPU which removes it from the PCI bus. Presumably this was to help prevent Windows apps from using the dGPU when the user didn't want them to but because of how it works it also means that when rebooted to Linux the dGPU no-longer exits. This patch enables a user to echo 0/1 to a WMI path to re-enable it (or disable, but the drivers *must* be unloaded first).

- eGPU enable: The ASUS x-flow lpatop has an iGPU, a dGPU, and an optional eGPU. This patch enables the user to echo 0/1 to a WMI path to enable or disable the eGPU. In ACPI this also appears to remove the dGPU from the PCI bus.

All of the above patches have been tested over the course of a few months. There is a small possibility of user error perhaps, where the user tries to enable or disable the dGPU/eGPU while drivers are loaded which would cause a system hang, but it is expected that almost all users would be using the asusctl daemon and dbus methods to manage the above which then eliminates these issues.

Luke D. Jones (3):
asus-wmi: Add panel overdrive functionality
asus-wmi: Add dgpu disable method
asus-wmi: Add egpu enable method

 drivers/platform/x86/asus-wmi.c            | 282 +++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |   7 +
 2 files changed, 289 insertions(+)

--
2.31.1

author maintainer
#1 lore raw

PATCH 1/3 asus-wmi: Add panel overdrive functionality

Some ASUS ROG laptops have the ability to drive the display panel a a higher rate to eliminate or reduce ghosting.

---
 drivers/platform/x86/asus-wmi.c            | 92 ++++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |  1 +
 2 files changed, 93 insertions(+)
drivers/platform/x86/asus-wmi.c +92 -0
index ebaeb7bb80f5..2468076d6cd8 100644
@@ -216,6 +216,9 @@ struct asus_wmi {
 	// The RSOC controls the maximum charging percentage.
 	bool battery_rsoc_available;
 
+	bool panel_overdrive_available;
+	u8 panel_overdrive;
+
 	struct hotplug_slot hotplug_slot;
 	struct mutex hotplug_lock;
 	struct mutex wmi_lock;
@@ -1221,6 +1224,87 @@ static int asus_wmi_rfkill_init(struct asus_wmi *asus)
 	return result;
 }
 
+/* Panel Overdrive ************************************************************/
+static int panel_od_check_present(struct asus_wmi *asus)
+{
+	u32 result;
+	int err;
+
+	asus->panel_overdrive_available = false;
+
+	err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_PANEL_OD, &result);
+	if (err) {
+		if (err == -ENODEV)
+			return 0;
+		return err;
+	}
+
+	if (result & ASUS_WMI_DSTS_PRESENCE_BIT)
+		asus->panel_overdrive_available = true;
+		asus->panel_overdrive = result & ASUS_WMI_DSTS_STATUS_BIT;
+
+	return 0;
+}
+
+static int panel_od_write(struct asus_wmi *asus)
+{
+	int err;
+	u8 value;
+	u32 retval;
+
+	value = asus->panel_overdrive;
+
+	err = asus_wmi_set_devstate(ASUS_WMI_DEVID_PANEL_OD, value, &retval);
+
+	sysfs_notify(&asus->platform_device->dev.kobj, NULL,
+			"panel_od");
+
+	if (err) {
+		pr_warn("Failed to set panel overdrive: %d\n", err);
+		return err;
+	}
+
+	if (retval > 1 || retval < 0) {
+		pr_warn("Failed to set panel overdrive (retval): 0x%x\n",
+			retval);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static ssize_t panel_od_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+	u8 mode = asus->panel_overdrive;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", mode);
+}
+
+static ssize_t panel_od_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	int result;
+	u8 overdrive;
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+
+	result = kstrtou8(buf, 10, &overdrive);
+	if (result < 0)
+		return result;
+
+	if (overdrive > 1 || overdrive < 0)
+		return -EINVAL;
+
+	asus->panel_overdrive = overdrive;
+	panel_od_write(asus);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(panel_od);
+
 /* Quirks *********************************************************************/
 
 static void asus_wmi_set_xusb2pr(struct asus_wmi *asus)
@@ -2332,6 +2416,7 @@ static struct attribute *platform_attributes[] = {
 	&dev_attr_als_enable.attr,
 	&dev_attr_fan_boost_mode.attr,
 	&dev_attr_throttle_thermal_policy.attr,
+	&dev_attr_panel_od.attr,
 	NULL
 };
 
@@ -2357,6 +2442,8 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj,
 		ok = asus->fan_boost_mode_available;
 	else if (attr == &dev_attr_throttle_thermal_policy.attr)
 		ok = asus->throttle_thermal_policy_available;
+	else if (attr == &dev_attr_panel_od.attr)
+		ok = asus->panel_overdrive_available;
 
 	if (devid != -1)
 		ok = !(asus_wmi_get_devstate_simple(asus, devid) < 0);
@@ -2622,6 +2709,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	else
 		throttle_thermal_policy_set_default(asus);
 
+	err = panel_od_check_present(asus);
+	if (err)
+		goto fail_panel_od;
+
 	err = asus_wmi_sysfs_init(asus->platform_device);
 	if (err)
 		goto fail_sysfs;
@@ -2709,6 +2800,7 @@ static int asus_wmi_add(struct platform_device *pdev)
 fail_throttle_thermal_policy:
 fail_fan_boost_mode:
 fail_platform:
+fail_panel_od:
 	kfree(asus);
 	return err;
 }
include/linux/platform_data/x86/asus-wmi.h +1 -0
index 2f274cf52805..428aea701c7b 100644
@@ -61,6 +61,7 @@
 #define ASUS_WMI_DEVID_THROTTLE_THERMAL_POLICY 0x00120075
 
 /* Misc */
+#define ASUS_WMI_DEVID_PANEL_OD		0x00050019
 #define ASUS_WMI_DEVID_CAMERA		0x00060013
 #define ASUS_WMI_DEVID_LID_FLIP		0x00060062
 
Signature · 1 line
2.31.1
#2 lore raw

Re: [PATCH 1/3] asus-wmi: Add panel overdrive functionality

Thank you for the patch! Perhaps something to improve:

Hi "Luke,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on linus/master]
[also build test WARNING on v5.13 next-20210701]
[If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Luke-D-Jones/Support-for-ASUS-egpu-dpgu-disable-panel-overdrive/20210705-062341
base:   https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git 28e92f990337b8b4c5fdec47667f8b96089c503e
config: x86_64-allyesconfig (attached as .config)
compiler: gcc-9 (Debian 9.3.0-22) 9.3.0
reproduce (this is a W=1 build):
        # https://github.com/0day-ci/linux/commit/b46e8ec7f42ce4b644c43f40218fe853d078f098
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Luke-D-Jones/Support-for-ASUS-egpu-dpgu-disable-panel-overdrive/20210705-062341
        git checkout b46e8ec7f42ce4b644c43f40218fe853d078f098
        # save the attached .config to linux build tree
        make W=1 ARCH=x86_64 

If you fix the issue, kindly add following tag as appropriate

All warnings (new ones prefixed by >>):

drivers/platform/x86/asus-wmi.c: In function 'panel_od_check_present':

>> drivers/platform/x86/asus-wmi.c:1242:2: warning: this 'if' clause does not guard... [-Wmisleading-indentation]
    1242 |  if (result & ASUS_WMI_DSTS_PRESENCE_BIT)
         |  ^~
   drivers/platform/x86/asus-wmi.c:1244:3: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'if'
    1244 |   asus->panel_overdrive = result & ASUS_WMI_DSTS_STATUS_BIT;
         |   ^~~~

Kconfig warnings: (for reference only)
WARNING: unmet direct dependencies detected for PHY_SPARX5_SERDES
Depends on (ARCH_SPARX5 || COMPILE_TEST && OF && HAS_IOMEM
Selected by
- SPARX5_SWITCH && NETDEVICES && ETHERNET && NET_VENDOR_MICROCHIP && NET_SWITCHDEV && HAS_IOMEM

vim +/if +1242 drivers/platform/x86/asus-wmi.c

1226
1227 /* Panel Overdrive ************************************************************/
1228 static int panel_od_check_present(struct asus_wmi *asus)
1229 {
1230 u32 result;
1231 int err;
1232
1233 asus->panel_overdrive_available = false;
1234
1235 err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_PANEL_OD, &result);
1236 if (err) {
1237 if (err == -ENODEV)
1238 return 0;
1239 return err;
1240 }
1241

> 1242		if (result & ASUS_WMI_DSTS_PRESENCE_BIT)

1243 asus->panel_overdrive_available = true;
1244 asus->panel_overdrive = result & ASUS_WMI_DSTS_STATUS_BIT;
1245
1246 return 0;
1247 }
1248

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org

#3 lore raw

Re: [PATCH 1/3] asus-wmi: Add panel overdrive functionality

In reply to Luke D. Jones

Hi,

Thank you for your patches, I've added several remarks inline (below);

Quoted 35 lines · Luke D. Jones

Some ASUS ROG laptops have the ability to drive the display panel a a higher rate to eliminate or reduce ghosting.

---
 drivers/platform/x86/asus-wmi.c            | 92 ++++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |  1 +
 2 files changed, 93 insertions(+)
drivers/platform/x86/asus-wmi.c +11 -0
index ebaeb7bb80f5..2468076d6cd8 100644
@@ -216,6 +216,9 @@ struct asus_wmi {
 	// The RSOC controls the maximum charging percentage.
 	bool battery_rsoc_available;
 
+	bool panel_overdrive_available;
+	u8 panel_overdrive;
+
 	struct hotplug_slot hotplug_slot;
 	struct mutex hotplug_lock;
 	struct mutex wmi_lock;
@@ -1221,6 +1224,87 @@ static int asus_wmi_rfkill_init(struct asus_wmi *asus)
 	return result;
 }
 
+/* Panel Overdrive ************************************************************/
+static int panel_od_check_present(struct asus_wmi *asus)
+{
+	u32 result;
+	int err;
+
+	asus->panel_overdrive_available = false;
+

drivers/platform/x86/asus-wmi.c static int asus_wmi_rfkill_init(struct asus_wmi *asus) · line 1244

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_PANEL_OD, &result);
+	if (err) {
+		if (err == -ENODEV)
+			return 0;
+		return err;
+	}
+
+	if (result & ASUS_WMI_DSTS_PRESENCE_BIT)
+		asus->panel_overdrive_available = true;
+		asus->panel_overdrive = result & ASUS_WMI_DSTS_STATUS_BIT;

As the kernel-test-robot pointed out this if is missing { } around the 2 statements which should only be executed if the condition is true.

Quoted 6 lines
drivers/platform/x86/asus-wmi.c +6 -0
+
+	return 0;
+}
+
+static int panel_od_write(struct asus_wmi *asus)
+{

drivers/platform/x86/asus-wmi.c static int asus_wmi_rfkill_init(struct asus_wmi *asus) · line 1260

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	int err;
+	u8 value;
+	u32 retval;
+
+	value = asus->panel_overdrive;
+
+	err = asus_wmi_set_devstate(ASUS_WMI_DEVID_PANEL_OD, value, &retval);
+
+	sysfs_notify(&asus->platform_device->dev.kobj, NULL,
+			"panel_od");

Please make this a single line.

drivers/platform/x86/asus-wmi.c static int asus_wmi_rfkill_init(struct asus_wmi *asus) · line 1269

Quoted 9 lines
drivers/platform/x86/asus-wmi.c +9 -0
+
+	if (err) {
+		pr_warn("Failed to set panel overdrive: %d\n", err);
+		return err;
+	}
+
+	if (retval > 1 || retval < 0) {
+		pr_warn("Failed to set panel overdrive (retval): 0x%x\n",
+			retval);

Please make this a single line too.

Quoted 18 lines
drivers/platform/x86/asus-wmi.c +18 -0
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static ssize_t panel_od_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+	u8 mode = asus->panel_overdrive;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", mode);
+}
+
+static ssize_t panel_od_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)

drivers/platform/x86/asus-wmi.c static int asus_wmi_rfkill_init(struct asus_wmi *asus) · line 1297

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+{
+	int result;
+	u8 overdrive;
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+
+	result = kstrtou8(buf, 10, &overdrive);
+	if (result < 0)
+		return result;
+
+	if (overdrive > 1 || overdrive < 0)

An u8 can never be < 0, so please drop that check (it will likely trigger compiler warnings in some cases).

Quoted 55 lines
drivers/platform/x86/asus-wmi.c +18 -0
+		return -EINVAL;
+
+	asus->panel_overdrive = overdrive;
+	panel_od_write(asus);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(panel_od);
+
 /* Quirks *********************************************************************/
 
 static void asus_wmi_set_xusb2pr(struct asus_wmi *asus)
@@ -2332,6 +2416,7 @@ static struct attribute *platform_attributes[] = {
 	&dev_attr_als_enable.attr,
 	&dev_attr_fan_boost_mode.attr,
 	&dev_attr_throttle_thermal_policy.attr,
+	&dev_attr_panel_od.attr,
 	NULL
 };
 
@@ -2357,6 +2442,8 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj,
 		ok = asus->fan_boost_mode_available;
 	else if (attr == &dev_attr_throttle_thermal_policy.attr)
 		ok = asus->throttle_thermal_policy_available;
+	else if (attr == &dev_attr_panel_od.attr)
+		ok = asus->panel_overdrive_available;
 
 	if (devid != -1)
 		ok = !(asus_wmi_get_devstate_simple(asus, devid) < 0);
@@ -2622,6 +2709,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	else
 		throttle_thermal_policy_set_default(asus);
 
+	err = panel_od_check_present(asus);
+	if (err)
+		goto fail_panel_od;
+
 	err = asus_wmi_sysfs_init(asus->platform_device);
 	if (err)
 		goto fail_sysfs;
@@ -2709,6 +2800,7 @@ static int asus_wmi_add(struct platform_device *pdev)
 fail_throttle_thermal_policy:
 fail_fan_boost_mode:
 fail_platform:
+fail_panel_od:
 	kfree(asus);
 	return err;
 }
include/linux/platform_data/x86/asus-wmi.h +0 -0
index 2f274cf52805..428aea701c7b 100644

include/linux/platform_data/x86/asus-wmi.h line 67

Quoted 7 lines
include/linux/platform_data/x86/asus-wmi.h +1 -0
@@ -61,6 +61,7 @@
 #define ASUS_WMI_DEVID_THROTTLE_THERMAL_POLICY 0x00120075
 
 /* Misc */
+#define ASUS_WMI_DEVID_PANEL_OD		0x00050019
 #define ASUS_WMI_DEVID_CAMERA		0x00060013
 #define ASUS_WMI_DEVID_LID_FLIP		0x00060062
 

Otherwise this looks good to me,

Regards,

Hans

#4 lore raw

Re: [PATCH 1/3] asus-wmi: Add panel overdrive functionality

In reply to Luke D. Jones

Hi,

One more remark inline:

Quoted 13 lines · Luke D. Jones

Some ASUS ROG laptops have the ability to drive the display panel a a higher rate to eliminate or reduce ghosting.

---
 drivers/platform/x86/asus-wmi.c            | 92 ++++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |  1 +
 2 files changed, 93 insertions(+)
drivers/platform/x86/asus-wmi.c +0 -0
index ebaeb7bb80f5..2468076d6cd8 100644

<snip>

drivers/platform/x86/asus-wmi.c static int asus_wmi_rfkill_init(struct asus_wmi *asus) · line 1282

Quoted 7 lines
drivers/platform/x86/asus-wmi.c +7 -0
+static ssize_t panel_od_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+	u8 mode = asus->panel_overdrive;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", mode);

As Barnabás pointed out in his review of patch 2/3, please use sysfs_emit here.

Regards,

Hans

author maintainer
#5 lore raw

PATCH 2/3 asus-wmi: Add dgpu disable method

In reply to Luke D. Jones

In Windows the ASUS Armory Crate progrm can enable or disable the dGPU via a WMI call. This functions much the same as various Linux methods in software where the dGPU is removed from the device tree.

However the WMI call saves the state of dGPU enabled or not and this then changes the dGPU visibility in Linux with no way for Linux users to re-enable it. We expose the WMI method so users can see and change the dGPU ACPI state.

---
 drivers/platform/x86/asus-wmi.c            | 98 ++++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |  3 +
 2 files changed, 101 insertions(+)
drivers/platform/x86/asus-wmi.c +98 -0
index 2468076d6cd8..8dc3f7ed021f 100644
@@ -210,6 +210,9 @@ struct asus_wmi {
 	u8 fan_boost_mode_mask;
 	u8 fan_boost_mode;
 
+	bool dgpu_disable_available;
+	u8 dgpu_disable_mode;
+
 	bool throttle_thermal_policy_available;
 	u8 throttle_thermal_policy_mode;
 
@@ -427,6 +430,93 @@ static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus)
 	}
 }
 
+/* dGPU ********************************************************************/
+static int dgpu_disable_check_present(struct asus_wmi *asus)
+{
+	u32 result;
+	int err;
+
+	asus->dgpu_disable_available = false;
+
+	err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_DGPU, &result);
+	if (err) {
+		if (err == -ENODEV)
+			return 0;
+		return err;
+	}
+
+	if (result & ASUS_WMI_DSTS_PRESENCE_BIT)
+		asus->dgpu_disable_available = true;
+		asus->dgpu_disable_mode = result & ASUS_WMI_DSTS_STATUS_BIT;
+
+	return 0;
+}
+
+static int dgpu_disable_write(struct asus_wmi *asus)
+{
+	int err;
+	u8 value;
+	u32 retval;
+
+	value = asus->dgpu_disable_mode;
+
+	err = asus_wmi_set_devstate(ASUS_WMI_DEVID_DGPU, value, &retval);
+
+	sysfs_notify(&asus->platform_device->dev.kobj, NULL,
+			"dgpu_disable");
+
+	if (err) {
+		pr_warn("Failed to set dgpu disable: %d\n", err);
+		return err;
+	}
+
+	if (retval > 1 || retval < 0) {
+		pr_warn("Failed to set dgpu disable (retval): 0x%x\n",
+			retval);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static ssize_t dgpu_disable_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+	u8 mode = asus->dgpu_disable_mode;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", mode);
+}
+
+static ssize_t dgpu_disable_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	int result;
+	u8 disable;
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+
+	result = kstrtou8(buf, 10, &disable);
+	if (result < 0)
+		return result;
+
+	if (disable > 1 || disable < 0)
+		return -EINVAL;
+
+	asus->dgpu_disable_mode = disable;
+	/*
+	 * The ACPI call used does not save the mode unless the call is run twice.
+	 * Once to disable, then once to check status and save - this is two code
+	 * paths in the method in the ACPI dumps.
+	*/
+	dgpu_disable_write(asus);
+	dgpu_disable_write(asus);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(dgpu_disable);
+
 /* Battery ********************************************************************/
 
 /* The battery maximum charging percentage */
@@ -2412,6 +2502,7 @@ static struct attribute *platform_attributes[] = {
 	&dev_attr_camera.attr,
 	&dev_attr_cardr.attr,
 	&dev_attr_touchpad.attr,
+	&dev_attr_dgpu_disable.attr,
 	&dev_attr_lid_resume.attr,
 	&dev_attr_als_enable.attr,
 	&dev_attr_fan_boost_mode.attr,
@@ -2438,6 +2529,8 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj,
 		devid = ASUS_WMI_DEVID_LID_RESUME;
 	else if (attr == &dev_attr_als_enable.attr)
 		devid = ASUS_WMI_DEVID_ALS_ENABLE;
+	else if (attr == &dev_attr_dgpu_disable.attr)
+		ok = asus->dgpu_disable_available;
 	else if (attr == &dev_attr_fan_boost_mode.attr)
 		ok = asus->fan_boost_mode_available;
 	else if (attr == &dev_attr_throttle_thermal_policy.attr)
@@ -2699,6 +2792,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	if (err)
 		goto fail_platform;
 
+	err = dgpu_disable_check_present(asus);
+	if (err)
+		goto fail_dgpu_disable;
+
 	err = fan_boost_mode_check_present(asus);
 	if (err)
 		goto fail_fan_boost_mode;
@@ -2799,6 +2896,7 @@ static int asus_wmi_add(struct platform_device *pdev)
 fail_sysfs:
 fail_throttle_thermal_policy:
 fail_fan_boost_mode:
+fail_dgpu_disable:
 fail_platform:
 fail_panel_od:
 	kfree(asus);
include/linux/platform_data/x86/asus-wmi.h +3 -0
index 428aea701c7b..a528f9d0e4b7 100644
@@ -90,6 +90,9 @@
 /* Keyboard dock */
 #define ASUS_WMI_DEVID_KBD_DOCK		0x00120063
 
+/* dgpu on/off */
+#define ASUS_WMI_DEVID_DGPU		0x00090020
+
 /* DSTS masks */
 #define ASUS_WMI_DSTS_STATUS_BIT	0x00000001
 #define ASUS_WMI_DSTS_UNKNOWN_BIT	0x00000002
Signature · 1 line
2.31.1
#6 lore raw

Re: [PATCH 2/3] asus-wmi: Add dgpu disable method

Hi

I have added a couple comments inline.

2021. július 5., hétfő 0:21 keltezéssel, Luke D. Jones írta:

Quoted 1 line

In Windows the ASUS Armory Crate progrm can enable or disable the

                                        ^

"program"

Quoted 4 lines

dGPU via a WMI call. This functions much the same as various Linux methods in software where the dGPU is removed from the device tree.

However the WMI call saves the state of dGPU enabled or not and this

I think "[...] the WMI call saves whether the dGPU is enabled or not, and [...]" might be better.
Or "[...] the WMI call saves the state of the dGPU (enabled or not) and [...]".

Quoted 37 lines

then changes the dGPU visibility in Linux with no way for Linux users to re-enable it. We expose the WMI method so users can see and change the dGPU ACPI state.

---
 drivers/platform/x86/asus-wmi.c            | 98 ++++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |  3 +
 2 files changed, 101 insertions(+)
drivers/platform/x86/asus-wmi.c +12 -0
index 2468076d6cd8..8dc3f7ed021f 100644
@@ -210,6 +210,9 @@ struct asus_wmi {
 	u8 fan_boost_mode_mask;
 	u8 fan_boost_mode;
 
+	bool dgpu_disable_available;
+	u8 dgpu_disable_mode;
+
 	bool throttle_thermal_policy_available;
 	u8 throttle_thermal_policy_mode;
 
@@ -427,6 +430,93 @@ static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus)
 	}
 }
 
+/* dGPU ********************************************************************/
+static int dgpu_disable_check_present(struct asus_wmi *asus)
+{
+	u32 result;
+	int err;
+
+	asus->dgpu_disable_available = false;
+
+	err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_DGPU, &result);

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 451

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	if (err) {
+		if (err == -ENODEV)
+			return 0;
+		return err;
+	}
+
+	if (result & ASUS_WMI_DSTS_PRESENCE_BIT)
+		asus->dgpu_disable_available = true;
+		asus->dgpu_disable_mode = result & ASUS_WMI_DSTS_STATUS_BIT;
+

Aren't braces missing here?

Quoted 5 lines
drivers/platform/x86/asus-wmi.c +5 -0
+	return 0;
+}
+
+static int dgpu_disable_write(struct asus_wmi *asus)
+{

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 466

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	int err;
+	u8 value;
+	u32 retval;
+
+	value = asus->dgpu_disable_mode;
+
+	err = asus_wmi_set_devstate(ASUS_WMI_DEVID_DGPU, value, &retval);
+
+	sysfs_notify(&asus->platform_device->dev.kobj, NULL,
+			"dgpu_disable");

A similar line with the exact same length in patch 3/3 is not broken in two. And shouldn't the notification be sent if the operation succeeded?

Quoted 12 lines
drivers/platform/x86/asus-wmi.c +12 -0
+
+	if (err) {
+		pr_warn("Failed to set dgpu disable: %d\n", err);
+		return err;
+	}
+
+	if (retval > 1 || retval < 0) {
+		pr_warn("Failed to set dgpu disable (retval): 0x%x\n",
+			retval);
+		return -EIO;
+	}
+

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 488

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	return 0;
+}
+
+static ssize_t dgpu_disable_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+	u8 mode = asus->dgpu_disable_mode;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", mode);

You could use sysfs_emit().

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 499

Quoted 11 lines
drivers/platform/x86/asus-wmi.c +11 -0
+}
+
+static ssize_t dgpu_disable_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	int result;
+	u8 disable;
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+
+	result = kstrtou8(buf, 10, &disable);

You could use kstrtobool(). I think that would be better since it accepts 'y', 'n', etc. in addition to 0 and 1.

Quoted 4 lines
drivers/platform/x86/asus-wmi.c +4 -0
+	if (result < 0)
+		return result;
+
+	if (disable > 1 || disable < 0)

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 513

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+		return -EINVAL;
+
+	asus->dgpu_disable_mode = disable;
+	/*
+	 * The ACPI call used does not save the mode unless the call is run twice.
+	 * Once to disable, then once to check status and save - this is two code
+	 * paths in the method in the ACPI dumps.
+	*/
+	dgpu_disable_write(asus);
+	dgpu_disable_write(asus);

Is there any reason the potential error codes are not returned?

Quoted 27 lines
drivers/platform/x86/asus-wmi.c +9 -0
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(dgpu_disable);
+
 /* Battery ********************************************************************/
 
 /* The battery maximum charging percentage */
@@ -2412,6 +2502,7 @@ static struct attribute *platform_attributes[] = {
 	&dev_attr_camera.attr,
 	&dev_attr_cardr.attr,
 	&dev_attr_touchpad.attr,
+	&dev_attr_dgpu_disable.attr,
 	&dev_attr_lid_resume.attr,
 	&dev_attr_als_enable.attr,
 	&dev_attr_fan_boost_mode.attr,
@@ -2438,6 +2529,8 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj,
 		devid = ASUS_WMI_DEVID_LID_RESUME;
 	else if (attr == &dev_attr_als_enable.attr)
 		devid = ASUS_WMI_DEVID_ALS_ENABLE;
+	else if (attr == &dev_attr_dgpu_disable.attr)
+		ok = asus->dgpu_disable_available;
 	else if (attr == &dev_attr_fan_boost_mode.attr)
 		ok = asus->fan_boost_mode_available;
 	else if (attr == &dev_attr_throttle_thermal_policy.attr)

drivers/platform/x86/asus-wmi.c static int asus_wmi_add(struct platform_device *pdev) · line 2798

Quoted 7 lines
drivers/platform/x86/asus-wmi.c +4 -0
@@ -2699,6 +2792,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	if (err)
 		goto fail_platform;
 
+	err = dgpu_disable_check_present(asus);
+	if (err)
+		goto fail_dgpu_disable;
+

Should this really be considered a "fatal" error?

Quoted 26 lines
drivers/platform/x86/asus-wmi.c +1 -0
 	err = fan_boost_mode_check_present(asus);
 	if (err)
 		goto fail_fan_boost_mode;
@@ -2799,6 +2896,7 @@ static int asus_wmi_add(struct platform_device *pdev)
 fail_sysfs:
 fail_throttle_thermal_policy:
 fail_fan_boost_mode:
+fail_dgpu_disable:
 fail_platform:
 fail_panel_od:
 	kfree(asus);
include/linux/platform_data/x86/asus-wmi.h +3 -1
index 428aea701c7b..a528f9d0e4b7 100644
@@ -90,6 +90,9 @@
 /* Keyboard dock */
 #define ASUS_WMI_DEVID_KBD_DOCK		0x00120063
 
+/* dgpu on/off */
+#define ASUS_WMI_DEVID_DGPU		0x00090020
+
 /* DSTS masks */
 #define ASUS_WMI_DSTS_STATUS_BIT	0x00000001
 #define ASUS_WMI_DSTS_UNKNOWN_BIT	0x00000002
--
Quoted 1 line

2.31.1

Regards,
Barnabás Pőcze

#7 lore raw

Re: [PATCH 2/3] asus-wmi: Add dgpu disable method

Hi,

Barnabás made some good points which I missed.

See me reply inline.

Quoted 7 lines · Barnabás Pőcze

Hi

I have added a couple comments inline.

2021. július 5., hétfő 0:21 keltezéssel, Luke D. Jones írta:

<snip>

Quoted 4 lines
Quoted 4 lines
drivers/platform/x86/asus-wmi.c +4 -0
+static ssize_t dgpu_disable_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
Quoted 8 lines

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 499

Quoted 5 lines
drivers/platform/x86/asus-wmi.c +5 -0
+	int result;
+	u8 disable;
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+
+	result = kstrtou8(buf, 10, &disable);

You could use kstrtobool(). I think that would be better since it accepts 'y', 'n', etc. in addition to 0 and 1.

Good point and the same applies to patch 1/3.

Quoted 8 lines
Quoted 8 lines
drivers/platform/x86/asus-wmi.c +8 -0
+	if (result < 0)
+		return result;
+
+	if (disable > 1 || disable < 0)
+		return -EINVAL;
+
+	asus->dgpu_disable_mode = disable;
+	/*
Quoted 8 lines

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 513

Quoted 6 lines
drivers/platform/x86/asus-wmi.c +6 -0
+	 * The ACPI call used does not save the mode unless the call is run twice.
+	 * Once to disable, then once to check status and save - this is two code
+	 * paths in the method in the ACPI dumps.
+	*/
+	dgpu_disable_write(asus);
+	dgpu_disable_write(asus);

Is there any reason the potential error codes are not returned?

Good question.

<snip>

Quoted 10 lines

drivers/platform/x86/asus-wmi.c static int asus_wmi_add(struct platform_device *pdev) · line 2798

Quoted 8 lines
drivers/platform/x86/asus-wmi.c +4 -0
@@ -2699,6 +2792,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	if (err)
 		goto fail_platform;
 
+	err = dgpu_disable_check_present(asus);
+	if (err)
+		goto fail_dgpu_disable;
+

Should this really be considered a "fatal" error?

Well dgpu_disable_check_present() does already contain:

		if (err == -ENODEV)
			return 0;

IOW it only returns an error on unexpected errors and asus_wmi_add() already contains a couple of other foo_present() checks which are dealt with in the same way, so this is consistent with that and being consistent is good, so I think this is fine.

Regards,

Hans

#8 lore raw

Re: [PATCH 2/3] asus-wmi: Add dgpu disable method

Hi

2021. július 6., kedd 12:17 keltezéssel, Hans de Goede írta:

Quoted 14 lines

[...]

Quoted 10 lines

drivers/platform/x86/asus-wmi.c static int asus_wmi_add(struct platform_device *pdev) · line 2798

Quoted 8 lines
drivers/platform/x86/asus-wmi.c +4 -0
@@ -2699,6 +2792,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	if (err)
 		goto fail_platform;
 
+	err = dgpu_disable_check_present(asus);
+	if (err)
+		goto fail_dgpu_disable;
+

Should this really be considered a "fatal" error?

Well dgpu_disable_check_present() does already contain:

Quoted 8 lines
		if (err == -ENODEV)
			return 0;

IOW it only returns an error on unexpected errors and asus_wmi_add() already contains a couple of other foo_present() checks which are dealt with in the same way, so this is consistent with that and being consistent is good, so I think this is fine.

Indeed, that's right, I missed that. I am still unsure whether any error should cause it to fail to load. But I guess if there is precedent for that in the module, then consistency is probably better.

Regards,
Barnabás Pőcze

author maintainer
#9 lore raw

Re: [PATCH 2/3] asus-wmi: Add dgpu disable method

In reply to Barnabás Pőcze

Thank you for the insightful feedback.

Quoted 11 lines · Barnabás Pőcze

Hi

I have added a couple comments inline.

2021. július 5., hétfő 0:21 keltezéssel, Luke D. Jones írta:

Quoted 1 line

In Windows the ASUS Armory Crate progrm can enable or disable the

                                        ^

"program"

My "a" key is a little hard to press sometimes :(

Quoted 10 lines
Quoted 5 lines

dGPU via a WMI call. This functions much the same as various Linux methods in software where the dGPU is removed from the device tree.

However the WMI call saves the state of dGPU enabled or not and this

I think "[...] the WMI call saves whether the dGPU is enabled or not, and [...]" might be better.
Or "[...] the WMI call saves the state of the dGPU (enabled or not) and [...]".

I've used the second option, thanks for pointing this out.

Quoted 53 lines
Quoted 44 lines

then changes the dGPU visibility in Linux with no way for Linux users to re-enable it. We expose the WMI method so users can see and change the dGPU ACPI state.

---

  drivers/platform/x86/asus-wmi.c            | 98 
++++++++++++++++++++++
  include/linux/platform_data/x86/asus-wmi.h |  3 +
  2 files changed, 101 insertions(+)

diff --git a/drivers/platform/x86/asus-wmi.c
b/drivers/platform/x86/asus-wmi.c
index 2468076d6cd8..8dc3f7ed021f 100644
--- a/drivers/platform/x86/asus-wmi.c
+++ b/drivers/platform/x86/asus-wmi.c
@@ -210,6 +210,9 @@ struct asus_wmi {
u8 fan_boost_mode_mask;
u8 fan_boost_mode;

+ bool dgpu_disable_available;
+ u8 dgpu_disable_mode;
+
bool throttle_thermal_policy_available;
u8 throttle_thermal_policy_mode;

@@ -427,6 +430,93 @@ static void
lid_flip_tablet_mode_get_state(struct asus_wmi *asus)
}
}

+/* dGPU
********************************************************************/
+static int dgpu_disable_check_present(struct asus_wmi *asus) +{
+ u32 result;
+ int err;
+
+ asus->dgpu_disable_available = false;
+
+ err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_DGPU, &result);
+ if (err) {
+ if (err == -ENODEV)

Quoted 8 lines

+ return 0;
+ return err;
+ }
+
+ if (result & ASUS_WMI_DSTS_PRESENCE_BIT)
+ asus->dgpu_disable_available = true;
+ asus->dgpu_disable_mode = result & ASUS_WMI_DSTS_STATUS_BIT;
+

Quoted 2 lines

Aren't braces missing here?

Yep. Fixed.

Quoted 17 lines
Quoted 16 lines

+ return 0;
+}
+
+static int dgpu_disable_write(struct asus_wmi *asus) +{
+ int err;
+ u8 value;
+ u32 retval;
+
+ value = asus->dgpu_disable_mode;
+
+ err = asus_wmi_set_devstate(ASUS_WMI_DEVID_DGPU, value, &retval);
+
+ sysfs_notify(&asus->platform_device->dev.kobj, NULL,
+ "dgpu_disable");

Quoted 3 lines

A similar line with the exact same length in patch 3/3 is not broken in two. And shouldn't the notification be sent if the operation succeeded?

Fixed. I moved the sysfs_notify down below the error returns.

Quoted 24 lines
Quoted 15 lines

+
+ if (err) {
+ pr_warn("Failed to set dgpu disable: %d\n", err);
+ return err;
+ }
+
+ if (retval > 1 || retval < 0) {
+ pr_warn("Failed to set dgpu disable (retval): 0x%x\n",
+ retval);
+ return -EIO;
+ }
+
+ return 0;
+}

Quoted 8 lines

+
+static ssize_t dgpu_disable_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct asus_wmi *asus = dev_get_drvdata(dev);
+ u8 mode = asus->dgpu_disable_mode;
+
+ return scnprintf(buf, PAGE_SIZE, "%d\n", mode);

Quoted 2 lines

You could use sysfs_emit().

Thanks. Many things like this I'm actually unaware of. Most of these patches are done by reading existing code.

Quoted 13 lines
Quoted 12 lines

+}
+
+static ssize_t dgpu_disable_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ int result;
+ u8 disable;
+ struct asus_wmi *asus = dev_get_drvdata(dev);
+
+ result = kstrtou8(buf, 10, &disable);

Quoted 3 lines

You could use kstrtobool(). I think that would be better since it accepts 'y', 'n', etc. in addition to 0 and 1.

Thanks! Wasn't aware of that. And since the setting for all 3 patches can only ever be 0/1 I've changed to use a bool instead of u8

Quoted 18 lines
Quoted 17 lines

+ if (result < 0)
+ return result;
+
+ if (disable > 1 || disable < 0)
+ return -EINVAL;
+
+ asus->dgpu_disable_mode = disable;
+ /*
+ * The ACPI call used does not save the mode unless the call is
run twice.
+ * Once to disable, then once to check status and save - this is
two code
+ * paths in the method in the ACPI dumps.
+ */
+ dgpu_disable_write(asus);
+ dgpu_disable_write(asus);

Quoted 2 lines

Is there any reason the potential error codes are not returned?

No I've fixed now. Guess I missed it.

Quoted 35 lines
Quoted 35 lines

+
+ return count;
+}
+
+static DEVICE_ATTR_RW(dgpu_disable);
+
/* Battery
********************************************************************/

/* The battery maximum charging percentage */
@@ -2412,6 +2502,7 @@ static struct attribute
*platform_attributes[] = {
&dev_attr_camera.attr,
&dev_attr_cardr.attr,
&dev_attr_touchpad.attr,
+ &dev_attr_dgpu_disable.attr,
&dev_attr_lid_resume.attr, &dev_attr_als_enable.attr, &dev_attr_fan_boost_mode.attr,
@@ -2438,6 +2529,8 @@ static umode_t asus_sysfs_is_visible(struct
kobject *kobj,
devid = ASUS_WMI_DEVID_LID_RESUME;
else if (attr == &dev_attr_als_enable.attr)
devid = ASUS_WMI_DEVID_ALS_ENABLE;
+ else if (attr == &dev_attr_dgpu_disable.attr)
+ ok = asus->dgpu_disable_available;
else if (attr == &dev_attr_fan_boost_mode.attr)
ok = asus->fan_boost_mode_available;
else if (attr == &dev_attr_throttle_thermal_policy.attr)
@@ -2699,6 +2792,10 @@ static int asus_wmi_add(struct
platform_device *pdev)
if (err)
goto fail_platform;

Quoted 7 lines
Quoted 4 lines

+ err = dgpu_disable_check_present(asus);
+ if (err)
+ goto fail_dgpu_disable;
+

Should this really be considered a "fatal" error?

I was modelling this on fail_fan_boost_mode and fail_throttle_thermal_policy since a laptop can't have both of those which indicates that a failed one is fine, it seemed appropriate to follow the same behaviour here

Quoted 32 lines
Quoted 22 lines

err = fan_boost_mode_check_present(asus); if (err)
goto fail_fan_boost_mode;
@@ -2799,6 +2896,7 @@ static int asus_wmi_add(struct
platform_device *pdev)
fail_sysfs:
fail_throttle_thermal_policy:
fail_fan_boost_mode:
+fail_dgpu_disable:
fail_platform:
fail_panel_od:
kfree(asus);
diff --git a/include/linux/platform_data/x86/asus-wmi.h
b/include/linux/platform_data/x86/asus-wmi.h
index 428aea701c7b..a528f9d0e4b7 100644
--- a/include/linux/platform_data/x86/asus-wmi.h +++ b/include/linux/platform_data/x86/asus-wmi.h @@ -90,6 +90,9 @@
/* Keyboard dock */
#define ASUS_WMI_DEVID_KBD_DOCK 0x00120063

Quoted 8 lines

+/* dgpu on/off */
+#define ASUS_WMI_DEVID_DGPU 0x00090020
+
/* DSTS masks */
#define ASUS_WMI_DSTS_STATUS_BIT 0x00000001
#define ASUS_WMI_DSTS_UNKNOWN_BIT 0x00000002
--
2.31.1

Quoted 2 lines

Regards,
Barnabás Pőcze

Many thanks for your feedback again.
Luke.

#10 lore raw

Re: [PATCH 2/3] asus-wmi: Add dgpu disable method

In reply to Luke D. Jones

Hi,

Some review remarks inline (mostly just echo-ing what Barnabás already said):

Quoted 41 lines · Luke D. Jones

In Windows the ASUS Armory Crate progrm can enable or disable the dGPU via a WMI call. This functions much the same as various Linux methods in software where the dGPU is removed from the device tree.

However the WMI call saves the state of dGPU enabled or not and this then changes the dGPU visibility in Linux with no way for Linux users to re-enable it. We expose the WMI method so users can see and change the dGPU ACPI state.

---
 drivers/platform/x86/asus-wmi.c            | 98 ++++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |  3 +
 2 files changed, 101 insertions(+)
drivers/platform/x86/asus-wmi.c +11 -0
index 2468076d6cd8..8dc3f7ed021f 100644
@@ -210,6 +210,9 @@ struct asus_wmi {
 	u8 fan_boost_mode_mask;
 	u8 fan_boost_mode;
 
+	bool dgpu_disable_available;
+	u8 dgpu_disable_mode;
+
 	bool throttle_thermal_policy_available;
 	u8 throttle_thermal_policy_mode;
 
@@ -427,6 +430,93 @@ static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus)
 	}
 }
 
+/* dGPU ********************************************************************/
+static int dgpu_disable_check_present(struct asus_wmi *asus)
+{
+	u32 result;
+	int err;
+
+	asus->dgpu_disable_available = false;
+

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 450

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_DGPU, &result);
+	if (err) {
+		if (err == -ENODEV)
+			return 0;
+		return err;
+	}
+
+	if (result & ASUS_WMI_DSTS_PRESENCE_BIT)
+		asus->dgpu_disable_available = true;
+		asus->dgpu_disable_mode = result & ASUS_WMI_DSTS_STATUS_BIT;

Missing {}

Quoted 6 lines
drivers/platform/x86/asus-wmi.c +6 -0
+
+	return 0;
+}
+
+static int dgpu_disable_write(struct asus_wmi *asus)
+{

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 466

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	int err;
+	u8 value;
+	u32 retval;
+
+	value = asus->dgpu_disable_mode;
+
+	err = asus_wmi_set_devstate(ASUS_WMI_DEVID_DGPU, value, &retval);
+
+	sysfs_notify(&asus->platform_device->dev.kobj, NULL,
+			"dgpu_disable");

Make this one line please.

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 475

Quoted 9 lines
drivers/platform/x86/asus-wmi.c +9 -0
+
+	if (err) {
+		pr_warn("Failed to set dgpu disable: %d\n", err);
+		return err;
+	}
+
+	if (retval > 1 || retval < 0) {
+		pr_warn("Failed to set dgpu disable (retval): 0x%x\n",
+			retval);

Make this one line please.

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 488

Quoted 13 lines
drivers/platform/x86/asus-wmi.c +13 -0
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static ssize_t dgpu_disable_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+	u8 mode = asus->dgpu_disable_mode;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", mode);

sysfs_emit() please.

Quoted 6 lines
drivers/platform/x86/asus-wmi.c +6 -0
+}
+
+static ssize_t dgpu_disable_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 504

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	int result;
+	u8 disable;
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+
+	result = kstrtou8(buf, 10, &disable);
+	if (result < 0)
+		return result;
+
+	if (disable > 1 || disable < 0)
+		return -EINVAL;

Drop the "disable < 0" check please.

Quoted 60 lines
drivers/platform/x86/asus-wmi.c +23 -0
+
+	asus->dgpu_disable_mode = disable;
+	/*
+	 * The ACPI call used does not save the mode unless the call is run twice.
+	 * Once to disable, then once to check status and save - this is two code
+	 * paths in the method in the ACPI dumps.
+	*/
+	dgpu_disable_write(asus);
+	dgpu_disable_write(asus);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(dgpu_disable);
+
 /* Battery ********************************************************************/
 
 /* The battery maximum charging percentage */
@@ -2412,6 +2502,7 @@ static struct attribute *platform_attributes[] = {
 	&dev_attr_camera.attr,
 	&dev_attr_cardr.attr,
 	&dev_attr_touchpad.attr,
+	&dev_attr_dgpu_disable.attr,
 	&dev_attr_lid_resume.attr,
 	&dev_attr_als_enable.attr,
 	&dev_attr_fan_boost_mode.attr,
@@ -2438,6 +2529,8 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj,
 		devid = ASUS_WMI_DEVID_LID_RESUME;
 	else if (attr == &dev_attr_als_enable.attr)
 		devid = ASUS_WMI_DEVID_ALS_ENABLE;
+	else if (attr == &dev_attr_dgpu_disable.attr)
+		ok = asus->dgpu_disable_available;
 	else if (attr == &dev_attr_fan_boost_mode.attr)
 		ok = asus->fan_boost_mode_available;
 	else if (attr == &dev_attr_throttle_thermal_policy.attr)
@@ -2699,6 +2792,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	if (err)
 		goto fail_platform;
 
+	err = dgpu_disable_check_present(asus);
+	if (err)
+		goto fail_dgpu_disable;
+
 	err = fan_boost_mode_check_present(asus);
 	if (err)
 		goto fail_fan_boost_mode;
@@ -2799,6 +2896,7 @@ static int asus_wmi_add(struct platform_device *pdev)
 fail_sysfs:
 fail_throttle_thermal_policy:
 fail_fan_boost_mode:
+fail_dgpu_disable:
 fail_platform:
 fail_panel_od:
 	kfree(asus);
include/linux/platform_data/x86/asus-wmi.h +0 -0
index 428aea701c7b..a528f9d0e4b7 100644

include/linux/platform_data/x86/asus-wmi.h line 98

Quoted 9 lines
include/linux/platform_data/x86/asus-wmi.h +3 -0
@@ -90,6 +90,9 @@
 /* Keyboard dock */
 #define ASUS_WMI_DEVID_KBD_DOCK		0x00120063
 
+/* dgpu on/off */
+#define ASUS_WMI_DEVID_DGPU		0x00090020
+
 /* DSTS masks */
 #define ASUS_WMI_DSTS_STATUS_BIT	0x00000001
 #define ASUS_WMI_DSTS_UNKNOWN_BIT	0x00000002

Otherwise this looks good to me.

Regards,

Hans

author maintainer
#11 lore raw

Re: [PATCH 2/3] asus-wmi: Add dgpu disable method

Thanks Hans, all feedback applied.

Quoted 213 lines · Hans de Goede

Hi,

Some review remarks inline (mostly just echo-ing what Barnabás already said):

Quoted 47 lines · Luke D. Jones

In Windows the ASUS Armory Crate progrm can enable or disable the dGPU via a WMI call. This functions much the same as various Linux methods in software where the dGPU is removed from the device tree.

However the WMI call saves the state of dGPU enabled or not and this then changes the dGPU visibility in Linux with no way for Linux users to re-enable it. We expose the WMI method so users can see and change the dGPU ACPI state.

---

  drivers/platform/x86/asus-wmi.c            | 98 
++++++++++++++++++++++
  include/linux/platform_data/x86/asus-wmi.h |  3 +
  2 files changed, 101 insertions(+)

diff --git a/drivers/platform/x86/asus-wmi.c
b/drivers/platform/x86/asus-wmi.c
index 2468076d6cd8..8dc3f7ed021f 100644
--- a/drivers/platform/x86/asus-wmi.c
+++ b/drivers/platform/x86/asus-wmi.c
@@ -210,6 +210,9 @@ struct asus_wmi {
u8 fan_boost_mode_mask;
u8 fan_boost_mode;

+ bool dgpu_disable_available;
+ u8 dgpu_disable_mode;
+
bool throttle_thermal_policy_available;
u8 throttle_thermal_policy_mode;

@@ -427,6 +430,93 @@ static void
lid_flip_tablet_mode_get_state(struct asus_wmi *asus)
}
}

+/* dGPU
********************************************************************/
+static int dgpu_disable_check_present(struct asus_wmi *asus) +{
+ u32 result;
+ int err;
+
+ asus->dgpu_disable_available = false;
+
+ err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_DGPU, &result);
+ if (err) {

Quoted 8 lines

+ if (err == -ENODEV)
+ return 0;
+ return err;
+ }
+
+ if (result & ASUS_WMI_DSTS_PRESENCE_BIT)
+ asus->dgpu_disable_available = true;
+ asus->dgpu_disable_mode = result & ASUS_WMI_DSTS_STATUS_BIT;

Missing {}

Quoted 8 lines

+
+ return 0;
+}
+
+static int dgpu_disable_write(struct asus_wmi *asus) +{
+ int err;
+ u8 value;

Quoted 8 lines

+ u32 retval;
+
+ value = asus->dgpu_disable_mode;
+
+ err = asus_wmi_set_devstate(ASUS_WMI_DEVID_DGPU, value, &retval);
+
+ sysfs_notify(&asus->platform_device->dev.kobj, NULL,
+ "dgpu_disable");

Make this one line please.

Quoted 9 lines

+
+ if (err) {
+ pr_warn("Failed to set dgpu disable: %d\n", err);
+ return err;
+ }
+
+ if (retval > 1 || retval < 0) {
+ pr_warn("Failed to set dgpu disable (retval): 0x%x\n",
+ retval);

Make this one line please.

Quoted 5 lines

+ return -EIO;
+ }
+
+ return 0;
+}

Quoted 8 lines

+
+static ssize_t dgpu_disable_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct asus_wmi *asus = dev_get_drvdata(dev);
+ u8 mode = asus->dgpu_disable_mode;
+
+ return scnprintf(buf, PAGE_SIZE, "%d\n", mode);

sysfs_emit() please.

Quoted 8 lines

+}
+
+static ssize_t dgpu_disable_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ int result;
+ u8 disable;

Quoted 8 lines

+ struct asus_wmi *asus = dev_get_drvdata(dev);
+
+ result = kstrtou8(buf, 10, &disable);
+ if (result < 0)
+ return result;
+
+ if (disable > 1 || disable < 0)
+ return -EINVAL;

Drop the "disable < 0" check please.

Quoted 70 lines

+
+ asus->dgpu_disable_mode = disable;
+ /*
+ * The ACPI call used does not save the mode unless the call is
run twice.
+ * Once to disable, then once to check status and save - this is
two code
+ * paths in the method in the ACPI dumps.
+ */
+ dgpu_disable_write(asus);
+ dgpu_disable_write(asus);
+
+ return count;
+}
+
+static DEVICE_ATTR_RW(dgpu_disable);
+
/* Battery
********************************************************************/

/* The battery maximum charging percentage */
@@ -2412,6 +2502,7 @@ static struct attribute
*platform_attributes[] = {
&dev_attr_camera.attr,
&dev_attr_cardr.attr,
&dev_attr_touchpad.attr,
+ &dev_attr_dgpu_disable.attr,
&dev_attr_lid_resume.attr, &dev_attr_als_enable.attr, &dev_attr_fan_boost_mode.attr,
@@ -2438,6 +2529,8 @@ static umode_t asus_sysfs_is_visible(struct
kobject *kobj,
devid = ASUS_WMI_DEVID_LID_RESUME;
else if (attr == &dev_attr_als_enable.attr)
devid = ASUS_WMI_DEVID_ALS_ENABLE;
+ else if (attr == &dev_attr_dgpu_disable.attr)
+ ok = asus->dgpu_disable_available;
else if (attr == &dev_attr_fan_boost_mode.attr)
ok = asus->fan_boost_mode_available;
else if (attr == &dev_attr_throttle_thermal_policy.attr)
@@ -2699,6 +2792,10 @@ static int asus_wmi_add(struct
platform_device *pdev)
if (err)
goto fail_platform;

+ err = dgpu_disable_check_present(asus);
+ if (err)
+ goto fail_dgpu_disable;
+
err = fan_boost_mode_check_present(asus); if (err)
goto fail_fan_boost_mode;
@@ -2799,6 +2896,7 @@ static int asus_wmi_add(struct
platform_device *pdev)
fail_sysfs:
fail_throttle_thermal_policy:
fail_fan_boost_mode:
+fail_dgpu_disable:
fail_platform:
fail_panel_od:
kfree(asus);
diff --git a/include/linux/platform_data/x86/asus-wmi.h
b/include/linux/platform_data/x86/asus-wmi.h
index 428aea701c7b..a528f9d0e4b7 100644
--- a/include/linux/platform_data/x86/asus-wmi.h +++ b/include/linux/platform_data/x86/asus-wmi.h @@ -90,6 +90,9 @@
/* Keyboard dock */
#define ASUS_WMI_DEVID_KBD_DOCK 0x00120063

Quoted 7 lines

+/* dgpu on/off */
+#define ASUS_WMI_DEVID_DGPU 0x00090020
+
/* DSTS masks */
#define ASUS_WMI_DSTS_STATUS_BIT 0x00000001
#define ASUS_WMI_DSTS_UNKNOWN_BIT 0x00000002

Otherwise this looks good to me.

Regards,

Hans

author maintainer
#12 lore raw

PATCH 3/3 asus-wmi: Add egpu enable method

In reply to Luke D. Jones

The X13 Flow laptops can utilise an external GPU. This requires toggling an ACPI method which will first disable the internal dGPU, and then enable the eGPU.

---
 drivers/platform/x86/asus-wmi.c            | 92 ++++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |  3 +
 2 files changed, 95 insertions(+)
drivers/platform/x86/asus-wmi.c +92 -0
index 8dc3f7ed021f..c9fe77456b7b 100644
@@ -210,6 +210,9 @@ struct asus_wmi {
 	u8 fan_boost_mode_mask;
 	u8 fan_boost_mode;
 
+	bool egpu_enable_available; // 0 = enable
+	u8 egpu_enable_mode;
+
 	bool dgpu_disable_available;
 	u8 dgpu_disable_mode;
 
@@ -430,6 +433,87 @@ static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus)
 	}
 }
 
+/* eGPU ********************************************************************/
+static int egpu_enable_check_present(struct asus_wmi *asus)
+{
+	u32 result;
+	int err;
+
+	asus->egpu_enable_available = false;
+
+	err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_EGPU, &result);
+	if (err) {
+		if (err == -ENODEV)
+			return 0;
+		return err;
+	}
+
+	if (result & ASUS_WMI_DSTS_PRESENCE_BIT) {
+		asus->egpu_enable_available = true;
+		asus->egpu_enable_mode = result & ASUS_WMI_DSTS_STATUS_BIT;
+	}
+
+	return 0;
+}
+
+static int egpu_enable_write(struct asus_wmi *asus)
+{
+	int err;
+	u8 value;
+	u32 retval;
+
+	value = asus->egpu_enable_mode;
+
+	err = asus_wmi_set_devstate(ASUS_WMI_DEVID_EGPU, value, &retval);
+
+	sysfs_notify(&asus->platform_device->dev.kobj, NULL, "egpu_enable");
+
+	if (err) {
+		pr_warn("Failed to set egpu disable: %d\n", err);
+		return err;
+	}
+
+	if (retval > 1 || retval < 0) {
+		pr_warn("Failed to set egpu disable (retval): 0x%x\n", retval);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static ssize_t egpu_enable_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+	u8 mode = asus->egpu_enable_mode;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", mode);
+}
+
+static ssize_t egpu_enable_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	int result;
+	u8 disable;
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+
+	result = kstrtou8(buf, 10, &disable);
+	if (result < 0)
+		return result;
+
+	if (disable > 1 || disable < 0)
+		return -EINVAL;
+
+	asus->egpu_enable_mode = disable;
+
+	egpu_enable_write(asus);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(egpu_enable);
+
 /* dGPU ********************************************************************/
 static int dgpu_disable_check_present(struct asus_wmi *asus)
 {
@@ -2502,6 +2586,7 @@ static struct attribute *platform_attributes[] = {
 	&dev_attr_camera.attr,
 	&dev_attr_cardr.attr,
 	&dev_attr_touchpad.attr,
+	&dev_attr_egpu_enable.attr,
 	&dev_attr_dgpu_disable.attr,
 	&dev_attr_lid_resume.attr,
 	&dev_attr_als_enable.attr,
@@ -2529,6 +2614,8 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj,
 		devid = ASUS_WMI_DEVID_LID_RESUME;
 	else if (attr == &dev_attr_als_enable.attr)
 		devid = ASUS_WMI_DEVID_ALS_ENABLE;
+	else if (attr == &dev_attr_egpu_enable.attr)
+		ok = asus->egpu_enable_available;
 	else if (attr == &dev_attr_dgpu_disable.attr)
 		ok = asus->dgpu_disable_available;
 	else if (attr == &dev_attr_fan_boost_mode.attr)
@@ -2792,6 +2879,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	if (err)
 		goto fail_platform;
 
+	err = egpu_enable_check_present(asus);
+	if (err)
+		goto fail_egpu_enable;
+
 	err = dgpu_disable_check_present(asus);
 	if (err)
 		goto fail_dgpu_disable;
@@ -2896,6 +2987,7 @@ static int asus_wmi_add(struct platform_device *pdev)
 fail_sysfs:
 fail_throttle_thermal_policy:
 fail_fan_boost_mode:
+fail_egpu_enable:
 fail_dgpu_disable:
 fail_platform:
 fail_panel_od:
include/linux/platform_data/x86/asus-wmi.h +3 -0
index a528f9d0e4b7..17dc5cb6f3f2 100644
@@ -90,6 +90,9 @@
 /* Keyboard dock */
 #define ASUS_WMI_DEVID_KBD_DOCK		0x00120063
 
+/* dgpu on/off */
+#define ASUS_WMI_DEVID_EGPU		0x00090019
+
 /* dgpu on/off */
 #define ASUS_WMI_DEVID_DGPU		0x00090020
 
Signature · 1 line
2.31.1
#13 lore raw

Re: [PATCH 3/3] asus-wmi: Add egpu enable method

Hi,

Quoted 37 lines · Luke D. Jones

The X13 Flow laptops can utilise an external GPU. This requires toggling an ACPI method which will first disable the internal dGPU, and then enable the eGPU.

---
 drivers/platform/x86/asus-wmi.c            | 92 ++++++++++++++++++++++
 include/linux/platform_data/x86/asus-wmi.h |  3 +
 2 files changed, 95 insertions(+)
drivers/platform/x86/asus-wmi.c +12 -0
index 8dc3f7ed021f..c9fe77456b7b 100644
@@ -210,6 +210,9 @@ struct asus_wmi {
 	u8 fan_boost_mode_mask;
 	u8 fan_boost_mode;
 
+	bool egpu_enable_available; // 0 = enable
+	u8 egpu_enable_mode;
+
 	bool dgpu_disable_available;
 	u8 dgpu_disable_mode;
 
@@ -430,6 +433,87 @@ static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus)
 	}
 }
 
+/* eGPU ********************************************************************/
+static int egpu_enable_check_present(struct asus_wmi *asus)
+{
+	u32 result;
+	int err;
+
+	asus->egpu_enable_available = false;
+
+	err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_EGPU, &result);

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 454

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	if (err) {
+		if (err == -ENODEV)
+			return 0;
+		return err;
+	}
+
+	if (result & ASUS_WMI_DSTS_PRESENCE_BIT) {
+		asus->egpu_enable_available = true;
+		asus->egpu_enable_mode = result & ASUS_WMI_DSTS_STATUS_BIT;
+	}

And now the braces are there (good) :)

Quoted 13 lines
drivers/platform/x86/asus-wmi.c +13 -0
+
+	return 0;
+}
+
+static int egpu_enable_write(struct asus_wmi *asus)
+{
+	int err;
+	u8 value;
+	u32 retval;
+
+	value = asus->egpu_enable_mode;
+
+	err = asus_wmi_set_devstate(ASUS_WMI_DEVID_EGPU, value, &retval);

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 477

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+
+	sysfs_notify(&asus->platform_device->dev.kobj, NULL, "egpu_enable");
+
+	if (err) {
+		pr_warn("Failed to set egpu disable: %d\n", err);
+		return err;
+	}
+
+	if (retval > 1 || retval < 0) {
+		pr_warn("Failed to set egpu disable (retval): 0x%x\n", retval);

And all these now are on one line, good again :)

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 490

Quoted 13 lines
drivers/platform/x86/asus-wmi.c +13 -0
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static ssize_t egpu_enable_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+	u8 mode = asus->egpu_enable_mode;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", mode);

sysfs_emit() please.

Quoted 6 lines
drivers/platform/x86/asus-wmi.c +6 -0
+}
+
+static ssize_t egpu_enable_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{

drivers/platform/x86/asus-wmi.c static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus) · line 506

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	int result;
+	u8 disable;
+	struct asus_wmi *asus = dev_get_drvdata(dev);
+
+	result = kstrtou8(buf, 10, &disable);
+	if (result < 0)
+		return result;
+
+	if (disable > 1 || disable < 0)
+		return -EINVAL;

Replace this with kstrtobool() ? or otherwise drop the disable < 0 check.

Quoted 55 lines
drivers/platform/x86/asus-wmi.c +18 -0
+
+	asus->egpu_enable_mode = disable;
+
+	egpu_enable_write(asus);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(egpu_enable);
+
 /* dGPU ********************************************************************/
 static int dgpu_disable_check_present(struct asus_wmi *asus)
 {
@@ -2502,6 +2586,7 @@ static struct attribute *platform_attributes[] = {
 	&dev_attr_camera.attr,
 	&dev_attr_cardr.attr,
 	&dev_attr_touchpad.attr,
+	&dev_attr_egpu_enable.attr,
 	&dev_attr_dgpu_disable.attr,
 	&dev_attr_lid_resume.attr,
 	&dev_attr_als_enable.attr,
@@ -2529,6 +2614,8 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj,
 		devid = ASUS_WMI_DEVID_LID_RESUME;
 	else if (attr == &dev_attr_als_enable.attr)
 		devid = ASUS_WMI_DEVID_ALS_ENABLE;
+	else if (attr == &dev_attr_egpu_enable.attr)
+		ok = asus->egpu_enable_available;
 	else if (attr == &dev_attr_dgpu_disable.attr)
 		ok = asus->dgpu_disable_available;
 	else if (attr == &dev_attr_fan_boost_mode.attr)
@@ -2792,6 +2879,10 @@ static int asus_wmi_add(struct platform_device *pdev)
 	if (err)
 		goto fail_platform;
 
+	err = egpu_enable_check_present(asus);
+	if (err)
+		goto fail_egpu_enable;
+
 	err = dgpu_disable_check_present(asus);
 	if (err)
 		goto fail_dgpu_disable;
@@ -2896,6 +2987,7 @@ static int asus_wmi_add(struct platform_device *pdev)
 fail_sysfs:
 fail_throttle_thermal_policy:
 fail_fan_boost_mode:
+fail_egpu_enable:
 fail_dgpu_disable:
 fail_platform:
 fail_panel_od:
include/linux/platform_data/x86/asus-wmi.h +0 -0
index a528f9d0e4b7..17dc5cb6f3f2 100644

include/linux/platform_data/x86/asus-wmi.h line 98

Quoted 9 lines
include/linux/platform_data/x86/asus-wmi.h +3 -0
@@ -90,6 +90,9 @@
 /* Keyboard dock */
 #define ASUS_WMI_DEVID_KBD_DOCK		0x00120063
 
+/* dgpu on/off */
+#define ASUS_WMI_DEVID_EGPU		0x00090019
+
 /* dgpu on/off */
 #define ASUS_WMI_DEVID_DGPU		0x00090020
 

Otherwise this looks good to me.

Regards,

Hans