max17042: Move power suppply registration to a worker thread
Sender : [email protected]<[email protected]>
Date : 2011-12-10 03:08 (GMT+09:00)
Title : [PATCH v2 1/6] max17042: Move power suppply registration to a worker thread
Quoted 10 lines
From: Dirk Brandewie <[email protected]>
This patch move the final registration of the battery to a worker thread in preperation for adding the POR proceedure recommended by maxim. This is needed since the Maxim init proceedure requires two long delays totaling 850ms. This patch will reduce the impact on system boot time. The battery will not be available to the power supply subsystem until the init proceedure is complete
Signed-off-by Dirk Brandewie <[email protected]>
The commit message is not updated for v2 patchset.
Besides, (sorry to report this now, I've just reminded this.) MAX17042 has a POR status bit according to the manual describing STATUS register (0x00). You need to do POR reset only when it is actually POR to MAX17042, not to CPU. At normal CPU shutdown/boot-up, POR procedure is not required as MAX17042 is not "rebooted". It is required only when the battery is suspected to be replaced. Thus, I tihink scheduling work and waiting for init_complete is required if POR is true.
Cheers!
MyungJoo
Quoted 90 lines
--- drivers/power/max17042_battery.c | 48 ++++++++++++++++++++++++++------------ 1 files changed, 33 insertions(+), 15 deletions(-)drivers/power/max17042_battery.c +33
-15@@ -34,6 +34,8 @@ struct max17042_chip {struct i2c_client *client;struct power_supply battery;struct max17042_platform_data *pdata; +struct work_struct work; +int init_complete; };static int max17042_write_reg (struct i2c_client *client,u8 reg,u16 value)@@ -86,6 +88,9 @@ static int max17042_get_property(struct power_supply *psy,struct max17042_chip *chip =container_of (psy, struct max17042_chip, battery); +if (!chip->init_complete) +return -EAGAIN ; +switch (psp) {case POWER_SUPPLY_PROP_PRESENT : val->intval = max17042_read_reg(chip->client,@@ -180,6 +185,31 @@ static int max17042_get_property(struct power_supply *psy,return 0 ; } +static void max17042_init_worker (struct work_struct *work) +{ +struct max17042_chip *chip =container_of (work, + struct max17042_chip, work); +struct i2c_client *client = chip->client; +int ret; + + +/* Initialize registers according to values from the platform data */ +if (chip->pdata->init_data) +max17042_set_reg (client, chip->pdata->init_data, + chip->pdata->num_init_data); + +if (!chip->pdata->enable_current_sense) { +max17042_write_reg (client,MAX17042_CGAIN ,0x0000 ); +max17042_write_reg (client, MAX17042_MiscCFG,0x0003 ); +max17042_write_reg (client, MAX17042_LearnCFG,0x0007 ); + }else { +if (chip->pdata->r_sns ==0 ) + chip->pdata->r_sns =MAX17042_DEFAULT_SNS_RESISTOR ; + } + + chip->init_complete =1 ; +} +static int __devinit max17042_probe (struct i2c_client *client,const struct i2c_device_id *id) {@@ -214,24 +244,12 @@ static int __devinit max17042_probe(struct i2c_client *client,if (ret) {dev_err (&client->dev,"failed: power supply register\n" );kfree (chip); -return ret; - } - -/* Initialize registers according to values from the platform data */ -if (chip->pdata->init_data) -max17042_set_reg (client, chip->pdata->init_data, - chip->pdata->num_init_data); - -if (!chip->pdata->enable_current_sense) { -max17042_write_reg (client,MAX17042_CGAIN ,0x0000 ); -max17042_write_reg (client, MAX17042_MiscCFG,0x0003 ); -max17042_write_reg (client, MAX17042_LearnCFG,0x0007 ); }else { -if (chip->pdata->r_sns ==0 ) - chip->pdata->r_sns =MAX17042_DEFAULT_SNS_RESISTOR ; +INIT_WORK (&chip->work, max17042_init_worker); +schedule_work (&chip->work); } -return 0 ; +return ret; } static int __devexit max17042_remove(struct i2c_client *client)Signature · 1 line
1.7.7.3
�淸�{.n�+돴윯돪�+%듚�깁負쪐w��{.n�+돴쪐{깸G쳺��{ay����,j�f"톒쉹��묎�z_溫(�쉸듶줷"얎�m����G쳺�◀?솳鈺�&x�~뤳턨O뺞촾퇉v�^�m����띠�◀?뻀�