PCI/PM: Target PM state is D3cold if the upstream bridge is power manageable
PATCH v2 1/1 PCI/PM: Target PM state is D3cold if the upstream bridge is power manageable
Some PCIe devices only support PME (Power Management Event) from D3cold. One example is ASMedia xHCI controller:
11:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI])
...
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
With such devices, if it has wake enabled, the kernel selects lowest possible power state to be D0 in pci_target_state(). This is problematic because it prevents the root port it is connected to enter low power state too which makes the system consume more energy than necessary.
The problem in pci_target_state() is that it only accounts the "current" device state, so when the bridge above it (a root port for instance) is transitioned into D3hot the device transitions into D3cold. This is because when the root port is first transitioned into D3hot then the ACPI power resource is turned off which puts the PCIe link to L2/L3 (and the root port and the device are in D3cold). If the root port is kept in D3hot it still means that the device below it is still effectively in D3cold as no configuration messages pass through. Furthermore the implementation note of PCIe 5.0 sec 5.3.1.4 says that the device should expect to be transitioned into D3cold soon after its link transitions into L2/L3 Ready state.
Taking the above into consideration, instead of forcing the device stay in D0 we look at the upstream bridge and whether it is allowed to enter D3 (hot/cold). If this is the case we conclude that the actual target state of the device is D3cold. This also follows the logic in pci_set_power_state() that sets power state of the subordinate devices to D3cold after the bridge itself is transitioned into D3cold.
---
Previous version of the patch can be found here:
https://patchwork.kernel.org/project/linux-pci/patch/[email protected]/
Changes from the previous version:
* Added Ack from Kai-Heng
* Reworked the commit log according to Bjorn's comments (I tried my best to answer the questions and explain the issue).
* Expanded the comment to mention why the target state is D3cold.
drivers/pci/pci.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-)
drivers/pci/pci.c +14 -1
@@ -2578,8 +2578,21 @@ static pci_power_t pci_target_state(struct pci_dev *dev, bool wakeup)return target_state; } -if (!dev->pm_cap) +if (!dev->pm_cap) { target_state =PCI_D0 ; + }else { +struct pci_dev *bridge; + +/* +* Look at the upstream bridge and whether it is allowed to +* enter D3hot (or D3cold). In both cases this device is +* not accessible anymore and its effective power state +* becomes D3cold. +*/ + bridge =pci_upstream_bridge (dev); +if (bridge &&pci_bridge_d3_possible (bridge)) + target_state = PCI_D3cold; + }/* * If the device is in D3cold even though it's not power-manageable by
Signature · 1 line
2.30.2
Quoted 9 lines · CEST Mika Westerberg
Some PCIe devices only support PME (Power Management Event) from D3cold. One example is ASMedia xHCI controller:
11:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI])
...
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mAPME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Quoted 4 lines
With such devices, if it has wake enabled, the kernel selects lowest possible power state to be D0 in
pci_target_state(). This is problematic because it prevents the root port it is connected to enter low power state too which makes the system consume more energy than necessary.
But this is not the only case affected by the patch AFAICS.
Quoted 3 lines
The problem in
pci_target_state()is that it only accounts the "current" device state, so when the bridge above it (a root port for instance) is transitioned into D3hot the device transitions into D3cold.
Well, as designed, pci_target_state() is about states the the device can be programmed into, which cannot be D3cold if the device has not platform PM.
Quoted 8 lines
This is because when the root port is first transitioned into D3hot then the ACPI power resource is turned off which puts the PCIe link to L2/L3 (and the root port and the device are in D3cold). If the root port is kept in D3hot it still means that the device below it is still effectively in D3cold as no configuration messages pass through. Furthermore the implementation note of PCIe 5.0 sec 5.3.1.4 says that the device should expect to be transitioned into D3cold soon after its link transitions into L2/L3 Ready state.
That's true, but the prerequisite is to put the endpoint device into D3hot and not to attempt to put it into D3cold.
Quoted 6 lines
Taking the above into consideration, instead of forcing the device stay in D0 we look at the upstream bridge and whether it is allowed to enter D3 (hot/cold). If this is the case we conclude that the actual target state of the device is D3cold. This also follows the logic in
pci_set_power_state()that sets power state of the subordinate devices to D3cold after the bridge itself is transitioned into D3cold.
IMO what needs to be fixed is what happens when the "wakeup" argument is "true" and that simply needs to special-case D3hot.
Namely, if wakeup from D3hot is not supported, D3hot should still be returned if wakeup from D3cold is supported and the upstream bridge supports D3cold.
Returning D3cold from pci_target_state() for devices that cannot be programmed into D3cold would be confusing IMV.
Quoted 48 lines
Reported-by Utkarsh H Patel <[email protected]>Reported-by Koba Ko <[email protected]>Tested-by Koba Ko <[email protected]>Acked-by Kai-Heng Feng <[email protected]>Signed-off-by Mika Westerberg <[email protected]>---
Previous version of the patch can be found here:https://patchwork.kernel.org/project/linux-pci/patch/[email protected]/
Changes from the previous version:
* Added Ack from Kai-Heng
* Reworked the commit log according to Bjorn's comments (I tried my best to answer the questions and explain the issue).
* Expanded the comment to mention why the target state is D3cold.drivers/pci/pci.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-)drivers/pci/pci.c +14
-1@@ -2578,8 +2578,21 @@ static pci_power_t pci_target_state(struct pci_dev *dev, bool wakeup)return target_state; } -if (!dev->pm_cap) +if (!dev->pm_cap) { target_state =PCI_D0 ; + }else { +struct pci_dev *bridge; + +/* +* Look at the upstream bridge and whether it is allowed to +* enter D3hot (or D3cold). In both cases this device is +* not accessible anymore and its effective power state +* becomes D3cold. +*/ + bridge =pci_upstream_bridge (dev); +if (bridge &&pci_bridge_d3_possible (bridge)) + target_state = PCI_D3cold; + }/* * If the device is in D3cold even though it's not power-manageable by
Hi Rafael,
Quoted 10 lines · Rafael J. Wysocki
Quoted 9 lines · CEST Mika Westerberg
Some PCIe devices only support PME (Power Management Event) from D3cold. One example is ASMedia xHCI controller:
11:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI])
...
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mAPME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Quoted 6 lines
Quoted 4 lines
With such devices, if it has wake enabled, the kernel selects lowest possible power state to be D0 in
pci_target_state(). This is problematic because it prevents the root port it is connected to enter low power state too which makes the system consume more energy than necessary.But this is not the only case affected by the patch AFAICS.
Right.
Quoted 6 lines
Quoted 3 lines
The problem in
pci_target_state()is that it only accounts the "current" device state, so when the bridge above it (a root port for instance) is transitioned into D3hot the device transitions into D3cold.Well, as designed,
pci_target_state()is about states the the device can be programmed into, which cannot be D3cold if the device has not platform PM.
Fair enough but the device itself does not need to have platform PM. It is enough that the root port far up in the hierarchy has it.
Quoted 11 lines
Quoted 8 lines
This is because when the root port is first transitioned into D3hot then the ACPI power resource is turned off which puts the PCIe link to L2/L3 (and the root port and the device are in D3cold). If the root port is kept in D3hot it still means that the device below it is still effectively in D3cold as no configuration messages pass through. Furthermore the implementation note of PCIe 5.0 sec 5.3.1.4 says that the device should expect to be transitioned into D3cold soon after its link transitions into L2/L3 Ready state.
That's true, but the prerequisite is to put the endpoint device into D3hot and not to attempt to put it into D3cold.
Okay.
Quoted 7 lines
Quoted 6 lines
Taking the above into consideration, instead of forcing the device stay in D0 we look at the upstream bridge and whether it is allowed to enter D3 (hot/cold). If this is the case we conclude that the actual target state of the device is D3cold. This also follows the logic in
pci_set_power_state()that sets power state of the subordinate devices to D3cold after the bridge itself is transitioned into D3cold.
Quoted 5 lines
IMO what needs to be fixed is what happens when the "wakeup" argument is "true" and that simply needs to special-case D3hot.
Namely, if wakeup from D3hot is not supported, D3hot should still be returned if wakeup from D3cold is supported and the upstream bridge supports D3cold.
This sounds like a good solution except that we probably need to look further up then to see if any of the bridges above support D3cold, right? For instance if the device is part of TBT topology there may be multiple bridges (PCIe upstream ports, downstream ports) between it and the root port that has the platform PM "support".
Quoted 56 lines · CEST Mika Westerberg
Hi Rafael,
Quoted 10 lines · Rafael J. Wysocki
Quoted 9 lines · CEST Mika Westerberg
Some PCIe devices only support PME (Power Management Event) from D3cold. One example is ASMedia xHCI controller:
11:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI])
...
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mAPME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-Quoted 6 lines
Quoted 4 lines
With such devices, if it has wake enabled, the kernel selects lowest possible power state to be D0 in
pci_target_state(). This is problematic because it prevents the root port it is connected to enter low power state too which makes the system consume more energy than necessary.But this is not the only case affected by the patch AFAICS.
Right.
Quoted 6 lines
Quoted 3 lines
The problem in
pci_target_state()is that it only accounts the "current" device state, so when the bridge above it (a root port for instance) is transitioned into D3hot the device transitions into D3cold.Well, as designed,
pci_target_state()is about states the the device can be programmed into, which cannot be D3cold if the device has not platform PM.Fair enough but the device itself does not need to have platform PM. It is enough that the root port far up in the hierarchy has it.
Quoted 11 lines
Quoted 8 lines
This is because when the root port is first transitioned into D3hot then the ACPI power resource is turned off which puts the PCIe link to L2/L3 (and the root port and the device are in D3cold). If the root port is kept in D3hot it still means that the device below it is still effectively in D3cold as no configuration messages pass through. Furthermore the implementation note of PCIe 5.0 sec 5.3.1.4 says that the device should expect to be transitioned into D3cold soon after its link transitions into L2/L3 Ready state.
That's true, but the prerequisite is to put the endpoint device into D3hot and not to attempt to put it into D3cold.
Okay.
Quoted 10 lines
Quoted 6 lines
Taking the above into consideration, instead of forcing the device stay in D0 we look at the upstream bridge and whether it is allowed to enter D3 (hot/cold). If this is the case we conclude that the actual target state of the device is D3cold. This also follows the logic in
pci_set_power_state()that sets power state of the subordinate devices to D3cold after the bridge itself is transitioned into D3cold.IMO what needs to be fixed is what happens when the "wakeup" argument is "true" and that simply needs to special-case D3hot.
Quoted 8 lines
Quoted 2 lines
Namely, if wakeup from D3hot is not supported, D3hot should still be returned if wakeup from D3cold is supported and the upstream bridge supports D3cold.
This sounds like a good solution except that we probably need to look further up then to see if any of the bridges above support D3cold, right? For instance if the device is part of TBT topology there may be multiple bridges (PCIe upstream ports, downstream ports) between it and the root port that has the platform PM "support".
Moreover, pci_enable_wake() would need to be modified to also enable PME if the target state is D3hot and only wakeup from D3cold is supported.
But if pci_enable_wake() is modified this way, we don't need to worry about the upstream bridges. Worst-case wakeup will not work (even though enabled) if the device stays in D3hot.
So pci_target_state() should return D3hot even if wakeup from D3hot itself is not supported, but wakeup from D3cold is supported, regardless of what the upstream bridges can do (with the assumption that power will get removed from the device via an upstream bridge) and pci_enable_wake() should be modified to enable PME if the target state is D3hot, but the device can only signal wakeup from D3cold.
IMO, allowing PME support from D3cold only without providing any means to put the device into D3cold is not a valid configuration and it need not be taken into account here.
Quoted 73 lines · Rafael J. Wysocki
Quoted 56 lines · CEST Mika Westerberg
Hi Rafael,
Quoted 10 lines · Rafael J. Wysocki
Quoted 9 lines · CEST Mika Westerberg
Some PCIe devices only support PME (Power Management Event) from D3cold. One example is ASMedia xHCI controller:
11:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI])
...
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mAPME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-Quoted 6 lines
Quoted 4 lines
With such devices, if it has wake enabled, the kernel selects lowest possible power state to be D0 in
pci_target_state(). This is problematic because it prevents the root port it is connected to enter low power state too which makes the system consume more energy than necessary.But this is not the only case affected by the patch AFAICS.
Right.
Quoted 6 lines
Quoted 3 lines
The problem in
pci_target_state()is that it only accounts the "current" device state, so when the bridge above it (a root port for instance) is transitioned into D3hot the device transitions into D3cold.Well, as designed,
pci_target_state()is about states the the device can be programmed into, which cannot be D3cold if the device has not platform PM.Fair enough but the device itself does not need to have platform PM. It is enough that the root port far up in the hierarchy has it.
Quoted 11 lines
Quoted 8 lines
This is because when the root port is first transitioned into D3hot then the ACPI power resource is turned off which puts the PCIe link to L2/L3 (and the root port and the device are in D3cold). If the root port is kept in D3hot it still means that the device below it is still effectively in D3cold as no configuration messages pass through. Furthermore the implementation note of PCIe 5.0 sec 5.3.1.4 says that the device should expect to be transitioned into D3cold soon after its link transitions into L2/L3 Ready state.
That's true, but the prerequisite is to put the endpoint device into D3hot and not to attempt to put it into D3cold.
Okay.
Quoted 10 lines
Quoted 6 lines
Taking the above into consideration, instead of forcing the device stay in D0 we look at the upstream bridge and whether it is allowed to enter D3 (hot/cold). If this is the case we conclude that the actual target state of the device is D3cold. This also follows the logic in
pci_set_power_state()that sets power state of the subordinate devices to D3cold after the bridge itself is transitioned into D3cold.IMO what needs to be fixed is what happens when the "wakeup" argument is "true" and that simply needs to special-case D3hot.
Quoted 8 lines
Quoted 2 lines
Namely, if wakeup from D3hot is not supported, D3hot should still be returned if wakeup from D3cold is supported and the upstream bridge supports D3cold.
This sounds like a good solution except that we probably need to look further up then to see if any of the bridges above support D3cold, right? For instance if the device is part of TBT topology there may be multiple bridges (PCIe upstream ports, downstream ports) between it and the root port that has the platform PM "support".
Moreover,
pci_enable_wake()would need to be modified to also enable PME if the target state is D3hot and only wakeup from D3cold is supported.But if
pci_enable_wake()is modified this way, we don't need to worry about the upstream bridges. Worst-case wakeup will not work (even though enabled) if the device stays in D3hot.
Quoted 6 lines
So
pci_target_state()should return D3hot even if wakeup from D3hot itself is not supported, but wakeup from D3cold is supported, regardless of what the upstream bridges can do (with the assumption that power will get removed from the device via an upstream bridge) andpci_enable_wake()should be modified to enable PME if the target state is D3hot, but the device can only signal wakeup from D3cold.
OK thanks. Let me try this in v3.
Quoted 3 lines
IMO, allowing PME support from D3cold only without providing any means to put the device into D3cold is not a valid configuration and it need not be taken into account here.
AFAIK you don't need the device to have any other means than that it responds to the L2/3 handshake properly according to the spec (so that the link can be put to L2). I think this is perfectly valid configuration :)