Skip to contentSkip to conversation

platform/x86: asus-wmi: add support for ASUS screenpad

PATCH Superseded Luke D. Jones 4 participants 18 messages May 5, 2023 – Jun 13, 2023

Subsystems (2)

v2 of 6 Superseded Latest is v6 →

lore
Share & tools
lore

Luke D. Jones

author maintainer
#0 lore raw

v2 cover platform/x86: asus-wmi: add support for ASUS screenpad

Adds support for the screenpad(-plus) found on a few ASUS laptops that have a main 16:9 or 16:10 screen and a shorter screen below the main but above the keyboard. The support consists of:
- On off control
- Setting brightness from 0-255

There are some small quirks with this device when considering only the raw WMI methods:
1. The Off method can only switch the device off
2. Changing the brightness turns the device back on
3. To turn the device back on the brightness must be > 1
4. When the device is off the brightness can't be changed (so it is stored by the driver if device is off).
5. Booting with a value of 0 brightness (retained by bios) means the bios will set a value of > 0, < 15 which is far too dim and was unexpected by testers. The compromise was to set the brightness to 60 which is a usable brightness if the module init brightness was under 15.
6. When the device is off it is "unplugged"

All of the above points are addressed within the patch to create a good user experience and keep within user expectations.

Changelog:
- V2
- Complete refactor to use as a backlight device

Luke D. Jones (1):
platform/x86: asus-wmi: add support for ASUS screenpad

 .../ABI/testing/sysfs-platform-asus-wmi       |   2 +-
 drivers/platform/x86/asus-wmi.c               | 132 ++++++++++++++++++
 drivers/platform/x86/asus-wmi.h               |   1 +
 include/linux/platform_data/x86/asus-wmi.h    |   4 +
 4 files changed, 138 insertions(+), 1 deletion(-)
Signature · 1 line
2.40.0
author maintainer
#1 lore raw

PATCH v2 1/1 platform/x86: asus-wmi: add support for ASUS screenpad

Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some high-end ASUS laptops like the GX650P series and others.

These methods are utilised in a new backlight device named:
- asus_screenpad

---
 .../ABI/testing/sysfs-platform-asus-wmi       |   2 +-
 drivers/platform/x86/asus-wmi.c               | 132 ++++++++++++++++++
 drivers/platform/x86/asus-wmi.h               |   1 +
 include/linux/platform_data/x86/asus-wmi.h    |   4 +
 4 files changed, 138 insertions(+), 1 deletion(-)
Documentation/ABI/testing/sysfs-platform-asus-wmi +1 -1
index a77a004a1baa..df9817c6233a 100644
@@ -97,4 +97,4 @@ Contact:	"Luke Jones" <[email protected]>
 Description:
 		Enable an LCD response-time boost to reduce or remove ghosting:
 			* 0 - Disable,
-			* 1 - Enable
+			* 1 - Enable
\ No newline at end of file
drivers/platform/x86/asus-wmi.c +132 -0

156 lines not on this page · raw message

drivers/platform/x86/asus-wmi.h +1 -0
index a478ebfd34df..5fbdd0eafa02 100644
@@ -57,6 +57,7 @@ struct quirk_entry {
 struct asus_wmi_driver {
 	int			brightness;
 	int			panel_power;
+	int			screenpad_brightness;
 	int			wlan_ctrl_by_user;
 
 	const char		*name;
include/linux/platform_data/x86/asus-wmi.h +4 -0
index 28234dc9fa6a..a2d94adb5c80 100644
@@ -58,6 +58,10 @@
 #define ASUS_WMI_DEVID_KBD_BACKLIGHT	0x00050021
 #define ASUS_WMI_DEVID_LIGHT_SENSOR	0x00050022 /* ?? */
 #define ASUS_WMI_DEVID_LIGHTBAR		0x00050025
+/* This can only be used to disable the screen, not re-enable */
+#define ASUS_WMI_DEVID_SCREENPAD_POWER	0x00050031
+/* Writing a brightness re-enables the screen if disabled */
+#define ASUS_WMI_DEVID_SCREENPAD_LIGHT	0x00050032
 #define ASUS_WMI_DEVID_FAN_BOOST_MODE	0x00110018
 #define ASUS_WMI_DEVID_THROTTLE_THERMAL_POLICY 0x00120075
 
Signature · 1 line
2.40.0
maintainer
#2 lore raw
Quoted 20 lines · Luke D. Jones

Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some high-end ASUS laptops like the GX650P series and others.

These methods are utilised in a new backlight device named:
- asus_screenpad

---
 .../ABI/testing/sysfs-platform-asus-wmi       |   2 +-
 drivers/platform/x86/asus-wmi.c               | 132 ++++++++++++++++++
 drivers/platform/x86/asus-wmi.h               |   1 +
 include/linux/platform_data/x86/asus-wmi.h    |   4 +
 4 files changed, 138 insertions(+), 1 deletion(-)
Documentation/ABI/testing/sysfs-platform-asus-wmi +0 -0
index a77a004a1baa..df9817c6233a 100644

Documentation/ABI/testing/sysfs-platform-asus-wmi Contact: "Luke Jones" <[email protected]> · line 100

Quoted 6 lines
Documentation/ABI/testing/sysfs-platform-asus-wmi +1 -1
@@ -97,4 +97,4 @@ Contact:	"Luke Jones" <[email protected]>
 Description:
 		Enable an LCD response-time boost to reduce or remove ghosting:
 			* 0 - Disable,
-			* 1 - Enable
+			* 1 - Enable
\ No newline at end of file

Spurious change?

Quoted 13 lines
drivers/platform/x86/asus-wmi.c +1 -0
index 1038dfdcdd32..0528eef02ef7 100644
@@ -200,6 +200,7 @@ struct asus_wmi {
 
 	struct input_dev *inputdev;
 	struct backlight_device *backlight_device;
+	struct backlight_device *screenpad_backlight_device;
 	struct platform_device *platform_device;
 
 	struct led_classdev wlan_led;

drivers/platform/x86/asus-wmi.c static int is_display_toggle(int code) · line 3216

Quoted 8 lines
drivers/platform/x86/asus-wmi.c +5 -0
@@ -3208,6 +3209,129 @@ static int is_display_toggle(int code)
 	return 0;
 }
 
+/* Screenpad backlight */
+
+static int read_screenpad_backlight_power(struct asus_wmi *asus)
+{
+	int ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Please move this to own line because now you have the extra newline in between the call and error handling.

Quoted 26 lines
drivers/platform/x86/asus-wmi.c +26 -0
+
+	if (ret < 0)
+		return ret;
+	/* 1 == powered */
+	return ret ? FB_BLANK_UNBLANK : FB_BLANK_POWERDOWN;
+}
+
+static int read_screenpad_brightness(struct backlight_device *bd)
+{
+	struct asus_wmi *asus = bl_get_data(bd);
+	u32 retval;
+	int err;
+
+	err = read_screenpad_backlight_power(asus);
+	if (err < 0)
+		return err;
+	/* The device brightness can only be read if powered, so return stored */
+	if (err == FB_BLANK_POWERDOWN)
+		return asus->driver->screenpad_brightness;
+
+	err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_SCREENPAD_LIGHT, &retval);
+	if (err < 0)
+		return err;
+
+	return retval & ASUS_WMI_DSTS_BRIGHTNESS_MASK;
+}

drivers/platform/x86/asus-wmi.c static int is_display_toggle(int code) · line 3252

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+
+static int update_screenpad_bl_status(struct backlight_device *bd)
+{
+	struct asus_wmi *asus = bl_get_data(bd);
+	int power, err = 0;
+	u32 ctrl_param;
+
+	power = read_screenpad_backlight_power(asus);
+	if (power == -ENODEV)
+		return err;

Just return 0. Or is there perhaps something wrong/missing here?

drivers/platform/x86/asus-wmi.c static int is_display_toggle(int code) · line 3258

Quoted 6 lines
drivers/platform/x86/asus-wmi.c +6 -0
+	else if (power < 0)
+		return power;
+
+	if (bd->props.power != power) {
+		if (power != FB_BLANK_UNBLANK) {
+			/* Only brightness can power it back on */

Only brightness > 0 can power the screen back on

drivers/platform/x86/asus-wmi.c static int is_display_toggle(int code) · line 3259

Quoted 1 line
drivers/platform/x86/asus-wmi.c +1 -0
+			ctrl_param = asus->driver->screenpad_brightness;

max(1, asus->driver->screenpad_brightness);

Don't forget to add the #include for it.

drivers/platform/x86/asus-wmi.c static int is_display_toggle(int code) · line 3262

Quoted 3 lines
drivers/platform/x86/asus-wmi.c +3 -0
+			/* Min 1 or the screen won't turn on */
+			if (ctrl_param == 0)
+				ctrl_param = 1;

Drop this.

drivers/platform/x86/asus-wmi.c static int is_display_toggle(int code) · line 3264

Quoted 2 lines
drivers/platform/x86/asus-wmi.c +2 -0
+			err = asus_wmi_set_devstate(ASUS_WMI_DEVID_SCREENPAD_LIGHT,
+							ctrl_param, NULL);

Align param.

drivers/platform/x86/asus-wmi.c static int is_display_toggle(int code) · line 3273

Quoted 9 lines
drivers/platform/x86/asus-wmi.c +9 -0
+		} else {
+			/* Ensure brightness is stored to turn back on with */
+			asus->driver->screenpad_brightness = bd->props.brightness;
+			err = asus_wmi_set_devstate(ASUS_WMI_DEVID_SCREENPAD_POWER, 0, NULL);
+		}
+	} else if (power == FB_BLANK_UNBLANK) {
+		/* Only set brightness if powered on or we get invalid/unsync state */
+		ctrl_param = bd->props.brightness;
+		err = asus_wmi_set_devstate(ASUS_WMI_DEVID_SCREENPAD_LIGHT, ctrl_param, NULL);

Why not store the brightness if powered off?

Quoted 34 lines
drivers/platform/x86/asus-wmi.c +34 -0
+	}
+
+	return err;
+}
+
+static const struct backlight_ops asus_screenpad_bl_ops = {
+	.get_brightness = read_screenpad_brightness,
+	.update_status = update_screenpad_bl_status,
+	.options = BL_CORE_SUSPENDRESUME,
+};
+
+static int asus_screenpad_init(struct asus_wmi *asus)
+{
+	struct backlight_device *bd;
+	struct backlight_properties props;
+	int power, brightness;
+
+	power = read_screenpad_backlight_power(asus);
+	if (power == -ENODEV)
+		power = FB_BLANK_UNBLANK;
+	else if (power < 0)
+		return power;
+
+	memset(&props, 0, sizeof(struct backlight_properties));
+	props.type = BACKLIGHT_RAW; /* ensure this bd is last to be picked */
+	props.max_brightness = 255;
+	bd = backlight_device_register("asus_screenpad",
+				       &asus->platform_device->dev, asus,
+				       &asus_screenpad_bl_ops, &props);
+	if (IS_ERR(bd)) {
+		pr_err("Could not register backlight device\n");
+		return PTR_ERR(bd);
+	}
+

drivers/platform/x86/asus-wmi.c static int is_display_toggle(int code) · line 3317

Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10 -0
+	asus->screenpad_backlight_device = bd;
+
+	brightness = read_screenpad_brightness(bd);
+	if (brightness < 0)
+		return brightness;
+	/*
+	 * Counter an odd behaviour where default is set to < 13 if it was 0 on boot.
+	 * 60 is subjective, but accepted as a good compromise to retain visibility.
+	 */
+	else if (brightness < 60)

Since the other branch returns, else is unnecessary.

Signature · 1 line
 i.
Quoted 70 lines
drivers/platform/x86/asus-wmi.c +25 -0
+		brightness = 60;
+
+	asus->driver->screenpad_brightness = brightness;
+	bd->props.brightness = brightness;
+	bd->props.power = power;
+	backlight_update_status(bd);
+
+	return 0;
+}
+
+static void asus_screenpad_exit(struct asus_wmi *asus)
+{
+	backlight_device_unregister(asus->screenpad_backlight_device);
+
+	asus->screenpad_backlight_device = NULL;
+}
+
 /* Fn-lock ********************************************************************/
 
 static bool asus_wmi_has_fnlock_key(struct asus_wmi *asus)
@@ -3823,6 +3947,13 @@ static int asus_wmi_add(struct platform_device *pdev)
 	} else if (asus->driver->quirks->wmi_backlight_set_devstate)
 		err = asus_wmi_set_devstate(ASUS_WMI_DEVID_BACKLIGHT, 2, NULL);
 
+	if (asus_wmi_dev_is_present(asus, ASUS_WMI_DEVID_SCREENPAD_LIGHT)) {
+		pr_warn("Begin asus_screenpad_init");
+		err = asus_screenpad_init(asus);
+		if (err && err != -ENODEV)
+			goto fail_backlight;
+	}
+
 	if (asus_wmi_has_fnlock_key(asus)) {
 		asus->fnlock_locked = fnlock_default;
 		asus_wmi_fnlock_update(asus);
@@ -3844,6 +3975,7 @@ static int asus_wmi_add(struct platform_device *pdev)
 
 fail_wmi_handler:
 	asus_wmi_backlight_exit(asus);
+	asus_screenpad_exit(asus);
 fail_backlight:
 	asus_wmi_rfkill_exit(asus);
 fail_rfkill:
drivers/platform/x86/asus-wmi.h +1 -0
index a478ebfd34df..5fbdd0eafa02 100644
@@ -57,6 +57,7 @@ struct quirk_entry {
 struct asus_wmi_driver {
 	int			brightness;
 	int			panel_power;
+	int			screenpad_brightness;
 	int			wlan_ctrl_by_user;
 
 	const char		*name;
include/linux/platform_data/x86/asus-wmi.h +4 -0
index 28234dc9fa6a..a2d94adb5c80 100644
@@ -58,6 +58,10 @@
 #define ASUS_WMI_DEVID_KBD_BACKLIGHT	0x00050021
 #define ASUS_WMI_DEVID_LIGHT_SENSOR	0x00050022 /* ?? */
 #define ASUS_WMI_DEVID_LIGHTBAR		0x00050025
+/* This can only be used to disable the screen, not re-enable */
+#define ASUS_WMI_DEVID_SCREENPAD_POWER	0x00050031
+/* Writing a brightness re-enables the screen if disabled */
+#define ASUS_WMI_DEVID_SCREENPAD_LIGHT	0x00050032
 #define ASUS_WMI_DEVID_FAN_BOOST_MODE	0x00110018
 #define ASUS_WMI_DEVID_THROTTLE_THERMAL_POLICY 0x00120075
 
author maintainer
#3 lore raw
Quoted 32 lines · Ilpo Järvinen
Quoted 17 lines · Luke D. Jones

Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some
high-end
ASUS laptops like the GX650P series and others.

These methods are utilised in a new backlight device named:
- asus_screenpad

---

  .../ABI/testing/sysfs-platform-asus-wmi       |   2 +-
  drivers/platform/x86/asus-wmi.c               | 132 
++++++++++++++++++
  drivers/platform/x86/asus-wmi.h               |   1 +
  include/linux/platform_data/x86/asus-wmi.h    |   4 +
  4 files changed, 138 insertions(+), 1 deletion(-)
Quoted 12 lines

diff --git a/Documentation/ABI/testing/sysfs-platform-asus-wmi
b/Documentation/ABI/testing/sysfs-platform-asus-wmi
index a77a004a1baa..df9817c6233a 100644
--- a/Documentation/ABI/testing/sysfs-platform-asus-wmi
+++ b/Documentation/ABI/testing/sysfs-platform-asus-wmi
@@ -97,4 +97,4 @@ Contact: "Luke Jones" <[email protected]>
Description:
Enable an LCD response-time boost to reduce or remove ghosting:
* 0 - Disable,
- * 1 - Enable
+ * 1 - Enable
\ No newline at end of file

Quoted 1 line

Spurious change?

Indeed it is. Not sure how that occurred.

Quoted 25 lines
Quoted 18 lines

diff --git a/drivers/platform/x86/asus-wmi.c
b/drivers/platform/x86/asus-wmi.c
index 1038dfdcdd32..0528eef02ef7 100644
--- a/drivers/platform/x86/asus-wmi.c
+++ b/drivers/platform/x86/asus-wmi.c
@@ -200,6 +200,7 @@ struct asus_wmi {

struct input_dev *inputdev;
struct backlight_device *backlight_device;
+ struct backlight_device *screenpad_backlight_device;
struct platform_device *platform_device;

struct led_classdev wlan_led;
@@ -3208,6 +3209,129 @@ static int is_display_toggle(int code)
return 0;
}

Quoted 6 lines

+/* Screenpad backlight */
+
+static int read_screenpad_backlight_power(struct asus_wmi *asus) +{
+ int ret = asus_wmi_get_devstate_simple(asus,
ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 2 lines

Please move this to own line because now you have the extra newline in between the call and error handling.

I don't understand what you mean sorry. Remove the new line or:
int ret;
ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 40 lines
Quoted 31 lines

+
+ if (ret < 0)
+ return ret;
+ /* 1 == powered */
+ return ret ? FB_BLANK_UNBLANK : FB_BLANK_POWERDOWN;
+}
+
+static int read_screenpad_brightness(struct backlight_device *bd) +{
+ struct asus_wmi *asus = bl_get_data(bd);
+ u32 retval;
+ int err;
+
+ err = read_screenpad_backlight_power(asus);
+ if (err < 0)
+ return err;
+ /* The device brightness can only be read if powered, so return
stored */
+ if (err == FB_BLANK_POWERDOWN)
+ return asus->driver->screenpad_brightness;
+
+ err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_SCREENPAD_LIGHT,
&retval);
+ if (err < 0)
+ return err;
+
+ return retval & ASUS_WMI_DSTS_BRIGHTNESS_MASK;
+}
+
+static int update_screenpad_bl_status(struct backlight_device *bd)

Quoted 8 lines

+{
+ struct asus_wmi *asus = bl_get_data(bd);
+ int power, err = 0;
+ u32 ctrl_param;
+
+ power = read_screenpad_backlight_power(asus);
+ if (power == -ENODEV)
+ return err;

Quoted 1 line

Just return 0. Or is there perhaps something wrong/missing here?

I thought the correct thing was to return any possible error state (here, anything less than 0 would be an error, right?)

Quoted 8 lines
Quoted 7 lines

+ else if (power < 0)
+ return power;
+
+ if (bd->props.power != power) {
+ if (power != FB_BLANK_UNBLANK) {
+ /* Only brightness can power it back on */

Quoted 7 lines

Only brightness > 0 can power the screen back on

Quoted 1 line

+ ctrl_param = asus->driver->screenpad_brightness;

max(1, asus->driver->screenpad_brightness);

Don't forget to add the #include for it.

Oh, that's handy! Thank you.

Quoted 6 lines
Quoted 4 lines

+ /* Min 1 or the screen won't turn on */
+ if (ctrl_param == 0)
+ ctrl_param = 1;

Drop this.

Thanks to minmax.

Quoted 5 lines
Quoted 3 lines

+ err = asus_wmi_set_devstate(ASUS_WMI_DEVID_SCREENPAD_LIGHT,
+ ctrl_param, NULL);

Align param.

Done.

Quoted 14 lines
Quoted 13 lines

+ } else {
+ /* Ensure brightness is stored to turn back on with */
+ asus->driver->screenpad_brightness = bd->props.brightness;
+ err = asus_wmi_set_devstate(ASUS_WMI_DEVID_SCREENPAD_POWER, 0,
NULL);
+ }
+ } else if (power == FB_BLANK_UNBLANK) {
+ /* Only set brightness if powered on or we get invalid/unsync
state */
+ ctrl_param = bd->props.brightness;
+ err = asus_wmi_set_devstate(ASUS_WMI_DEVID_SCREENPAD_LIGHT,
ctrl_param, NULL);

Quoted 1 line

Why not store the brightness if powered off?

That's me being literal and short sighted. I've now moved:

```
/* Ensure brightness is stored to turn back on with */
asus->driver->screenpad_brightness = bd->props.brightness;
```

to below the conditional blocks.

Quoted 49 lines
Quoted 40 lines

+ }
+
+ return err;
+}
+
+static const struct backlight_ops asus_screenpad_bl_ops = {
+ .get_brightness = read_screenpad_brightness,
+ .update_status = update_screenpad_bl_status,
+ .options = BL_CORE_SUSPENDRESUME,
+};
+
+static int asus_screenpad_init(struct asus_wmi *asus) +{
+ struct backlight_device *bd;
+ struct backlight_properties props;
+ int power, brightness;
+
+ power = read_screenpad_backlight_power(asus);
+ if (power == -ENODEV)
+ power = FB_BLANK_UNBLANK;
+ else if (power < 0)
+ return power;
+
+ memset(&props, 0, sizeof(struct backlight_properties));
+ props.type = BACKLIGHT_RAW; /* ensure this bd is last to be
picked */
+ props.max_brightness = 255;
+ bd = backlight_device_register("asus_screenpad",
+ &asus->platform_device->dev, asus,
+ &asus_screenpad_bl_ops, &props);
+ if (IS_ERR(bd)) {
+ pr_err("Could not register backlight device\n");
+ return PTR_ERR(bd);
+ }
+
+ asus->screenpad_backlight_device = bd;
+
+ brightness = read_screenpad_brightness(bd);
+ if (brightness < 0)

Quoted 8 lines

+ return brightness;
+ /*
+ * Counter an odd behaviour where default is set to < 13 if it
was 0 on boot.
+ * 60 is subjective, but accepted as a good compromise to retain
visibility.
+ */
+ else if (brightness < 60)

Quoted 1 line

Since the other branch returns, else is unnecessary.

Good catch, thank you.

I'll submit V3 after we clarify the two points above that I'm confused by :)

Thank you for taking the time to review.

Quoted 1 line
#4 lore raw
Quoted 104 lines · Luke Jones
Quoted 29 lines · Ilpo Järvinen
Quoted 15 lines · Luke D. Jones

 Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some high-end ASUS laptops like the GX650P series and others.

 These methods are utilised in a new backlight device named:
 - asus_screenpad

 ---
  .../ABI/testing/sysfs-platform-asus-wmi       |   2 +- drivers/platform/x86/asus-wmi.c               | 132 ++++++++++++++++++ drivers/platform/x86/asus-wmi.h               |   1 + include/linux/platform_data/x86/asus-wmi.h    |   4 +

  4 files changed, 138 insertions(+), 1 deletion(-)
Quoted 11 lines

 diff --git a/Documentation/ABI/testing/sysfs-platform-asus-wmi b/Documentation/ABI/testing/sysfs-platform-asus-wmi index a77a004a1baa..df9817c6233a 100644
 --- a/Documentation/ABI/testing/sysfs-platform-asus-wmi
 +++ b/Documentation/ABI/testing/sysfs-platform-asus-wmi
 @@ -97,4 +97,4 @@ Contact:    "Luke Jones" <[email protected]>
  Description:
          Enable an LCD response-time boost to reduce or remove ghosting:
              * 0 - Disable,
 -            * 1 - Enable
 +            * 1 - Enable
 \ No newline at end of file

Quoted 1 line

Spurious change?

Indeed it is. Not sure how that occurred.

Quoted 17 lines
Quoted 17 lines

 diff --git a/drivers/platform/x86/asus-wmi.c b/drivers/platform/x86/asus-wmi.c index 1038dfdcdd32..0528eef02ef7 100644
 --- a/drivers/platform/x86/asus-wmi.c
 +++ b/drivers/platform/x86/asus-wmi.c
 @@ -200,6 +200,7 @@ struct asus_wmi {

      struct input_dev *inputdev;
      struct backlight_device *backlight_device; +    struct backlight_device *screenpad_backlight_device; struct platform_device *platform_device;

      struct led_classdev wlan_led;
 @@ -3208,6 +3209,129 @@ static int is_display_toggle(int code) return 0;
  }

Quoted 8 lines
Quoted 5 lines

 +/* Screenpad backlight */
 +
 +static int read_screenpad_backlight_power(struct asus_wmi *asus)
 +{
 +    int ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Please move this to own line because now you have the extra newline in between the call and error handling.

I don't understand what you mean sorry. Remove the new line or:
int ret;
ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 38 lines
Quoted 37 lines

 +
 +    if (ret < 0)
 +        return ret;
 +    /* 1 == powered */
 +    return ret ? FB_BLANK_UNBLANK : FB_BLANK_POWERDOWN;
 +}
 +
 +static int read_screenpad_brightness(struct backlight_device *bd) +{
 +    struct asus_wmi *asus = bl_get_data(bd);
 +    u32 retval;
 +    int err;
 +
 +    err = read_screenpad_backlight_power(asus);
 +    if (err < 0)
 +        return err;
 +    /* The device brightness can only be read if powered, so return stored */ +    if (err == FB_BLANK_POWERDOWN)
 +        return asus->driver->screenpad_brightness;
 +
 +    err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_SCREENPAD_LIGHT, &retval); +    if (err < 0)
 +        return err;
 +
 +    return retval & ASUS_WMI_DSTS_BRIGHTNESS_MASK;
 +}
 +
 +static int update_screenpad_bl_status(struct backlight_device *bd) +{
 +    struct asus_wmi *asus = bl_get_data(bd);
 +    int power, err = 0;
 +    u32 ctrl_param;
 +
 +    power = read_screenpad_backlight_power(asus);
 +    if (power == -ENODEV)
 +        return err;

Quoted 4 lines
Quoted 1 line

Just return 0. Or is there perhaps something wrong/missing here?

I thought the correct thing was to return any possible error state (here, anything less than 0 would be an error, right?)

Well, yes, but you are not returning an error. You are returning 'err' which is 0 at this point. So, at the very least, this code is (very) misleading since it suggests that it would return some error (as saved in the 'err' variable) when it doesn't.

Guenter

author maintainer
#5 lore raw
Quoted 119 lines · Guenter Roeck
Quoted 113 lines · Luke Jones
Quoted 33 lines · Ilpo Järvinen
Quoted 17 lines · Luke D. Jones

Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some
high-end
ASUS laptops like the GX650P series and others.

These methods are utilised in a new backlight device named:
- asus_screenpad

---

  .../ABI/testing/sysfs-platform-asus-wmi       |   2 +-
  drivers/platform/x86/asus-wmi.c               | 132 
++++++++++++++++++
  drivers/platform/x86/asus-wmi.h               |   1 +
  include/linux/platform_data/x86/asus-wmi.h    |   4 +
  4 files changed, 138 insertions(+), 1 deletion(-)
Quoted 13 lines

diff --git a/Documentation/ABI/testing/sysfs-platform-asus-wmi
b/Documentation/ABI/testing/sysfs-platform-asus-wmi
index a77a004a1baa..df9817c6233a 100644
--- a/Documentation/ABI/testing/sysfs-platform-asus-wmi +++ b/Documentation/ABI/testing/sysfs-platform-asus-wmi
@@ -97,4 +97,4 @@ Contact: "Luke Jones" <[email protected]>
Description:
Enable an LCD response-time boost to reduce or remove
ghosting:
* 0 - Disable,
- * 1 - Enable
+ * 1 - Enable
\ No newline at end of file

Quoted 1 line

Spurious change?

Indeed it is. Not sure how that occurred.

Quoted 25 lines
Quoted 16 lines

diff --git a/drivers/platform/x86/asus-wmi.c
b/drivers/platform/x86/asus-wmi.c
index 1038dfdcdd32..0528eef02ef7 100644
--- a/drivers/platform/x86/asus-wmi.c
+++ b/drivers/platform/x86/asus-wmi.c
@@ -200,6 +200,7 @@ struct asus_wmi {

      struct input_dev *inputdev;
      struct backlight_device *backlight_device;
 +    struct backlight_device *screenpad_backlight_device;
      struct platform_device *platform_device;

      struct led_classdev wlan_led;
 @@ -3208,6 +3209,129 @@ static int is_display_toggle(int code)
      return 0;
Quoted 8 lines

}

+/* Screenpad backlight */
+
+static int read_screenpad_backlight_power(struct asus_wmi *asus) +{
+ int ret = asus_wmi_get_devstate_simple(asus,
ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 2 lines

Please move this to own line because now you have the extra newline in between the call and error handling.

I don't understand what you mean sorry. Remove the new line or:
int ret;
ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 41 lines
Quoted 40 lines

+
+ if (ret < 0)
+ return ret;
+ /* 1 == powered */
+ return ret ? FB_BLANK_UNBLANK : FB_BLANK_POWERDOWN;
+}
+
+static int read_screenpad_brightness(struct backlight_device *bd) +{

 +    struct asus_wmi *asus = bl_get_data(bd);
 +    u32 retval;
 +    int err;

+
+ err = read_screenpad_backlight_power(asus);
+ if (err < 0)
+ return err;
+ /* The device brightness can only be read if powered, so
return stored */
+ if (err == FB_BLANK_POWERDOWN)
+ return asus->driver->screenpad_brightness;
+
+ err = asus_wmi_get_devstate(asus,
ASUS_WMI_DEVID_SCREENPAD_LIGHT, &retval);
+ if (err < 0)
+ return err;
+
+ return retval & ASUS_WMI_DSTS_BRIGHTNESS_MASK;
+}
+
+static int update_screenpad_bl_status(struct backlight_device
*bd)
+{

 +    struct asus_wmi *asus = bl_get_data(bd);
 +    int power, err = 0;
 +    u32 ctrl_param;

+
+ power = read_screenpad_backlight_power(asus);
+ if (power == -ENODEV)
+ return err;

Quoted 4 lines
Quoted 1 line

Just return 0. Or is there perhaps something wrong/missing here?

I thought the correct thing was to return any possible error state (here, anything less than 0 would be an error, right?)

Quoted 7 lines

Well, yes, but you are not returning an error. You are returning 'err' which is 0 at this point. So, at the very least, this code is (very) misleading since it suggests that it would return some error (as saved in the 'err' variable) when it doesn't.

Guenter

Oh! Right I see it now, I'm sorry, I just kept skipping over it somehow.

So I should change to:

	power = read_screenpad_backlight_power(asus);
	if (power < 0)
		return power;

Is that acceptable?

#6 lore raw
Quoted 121 lines · Luke Jones
Quoted 110 lines · Guenter Roeck
Quoted 104 lines · Luke Jones
Quoted 29 lines · Ilpo Järvinen
Quoted 15 lines · Luke D. Jones

 Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some high-end ASUS laptops like the GX650P series and others.

 These methods are utilised in a new backlight device named:
 - asus_screenpad

 ---
  .../ABI/testing/sysfs-platform-asus-wmi       |   2 +- drivers/platform/x86/asus-wmi.c               | 132 ++++++++++++++++++ drivers/platform/x86/asus-wmi.h               |   1 + include/linux/platform_data/x86/asus-wmi.h    |   4 +

  4 files changed, 138 insertions(+), 1 deletion(-)
Quoted 11 lines

 diff --git a/Documentation/ABI/testing/sysfs-platform-asus-wmi b/Documentation/ABI/testing/sysfs-platform-asus-wmi index a77a004a1baa..df9817c6233a 100644
 --- a/Documentation/ABI/testing/sysfs-platform-asus-wmi
 +++ b/Documentation/ABI/testing/sysfs-platform-asus-wmi
 @@ -97,4 +97,4 @@ Contact:    "Luke Jones" <[email protected]>
  Description:
          Enable an LCD response-time boost to reduce or remove ghosting:
              * 0 - Disable,
 -            * 1 - Enable
 +            * 1 - Enable
 \ No newline at end of file

Quoted 1 line

Spurious change?

Indeed it is. Not sure how that occurred.

Quoted 17 lines
Quoted 17 lines

 diff --git a/drivers/platform/x86/asus-wmi.c b/drivers/platform/x86/asus-wmi.c index 1038dfdcdd32..0528eef02ef7 100644
 --- a/drivers/platform/x86/asus-wmi.c
 +++ b/drivers/platform/x86/asus-wmi.c
 @@ -200,6 +200,7 @@ struct asus_wmi {

      struct input_dev *inputdev;
      struct backlight_device *backlight_device; +    struct backlight_device *screenpad_backlight_device; struct platform_device *platform_device;

      struct led_classdev wlan_led;
 @@ -3208,6 +3209,129 @@ static int is_display_toggle(int code) return 0;
  }

Quoted 8 lines
Quoted 5 lines

 +/* Screenpad backlight */
 +
 +static int read_screenpad_backlight_power(struct asus_wmi *asus)
 +{
 +    int ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Please move this to own line because now you have the extra newline in between the call and error handling.

I don't understand what you mean sorry. Remove the new line or:
int ret;
ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 38 lines
Quoted 37 lines

 +
 +    if (ret < 0)
 +        return ret;
 +    /* 1 == powered */
 +    return ret ? FB_BLANK_UNBLANK : FB_BLANK_POWERDOWN;
 +}
 +
 +static int read_screenpad_brightness(struct backlight_device *bd) +{
 +    struct asus_wmi *asus = bl_get_data(bd);
 +    u32 retval;
 +    int err;
 +
 +    err = read_screenpad_backlight_power(asus);
 +    if (err < 0)
 +        return err;
 +    /* The device brightness can only be read if powered, so return stored */ +    if (err == FB_BLANK_POWERDOWN)
 +        return asus->driver->screenpad_brightness;
 +
 +    err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_SCREENPAD_LIGHT, &retval); +    if (err < 0)
 +        return err;
 +
 +    return retval & ASUS_WMI_DSTS_BRIGHTNESS_MASK;
 +}
 +
 +static int update_screenpad_bl_status(struct backlight_device *bd) +{
 +    struct asus_wmi *asus = bl_get_data(bd);
 +    int power, err = 0;
 +    u32 ctrl_param;
 +
 +    power = read_screenpad_backlight_power(asus);
 +    if (power == -ENODEV)
 +        return err;

Quoted 4 lines
Quoted 1 line

Just return 0. Or is there perhaps something wrong/missing here?

I thought the correct thing was to return any possible error state (here, anything less than 0 would be an error, right?)

Quoted 7 lines

Well, yes, but you are not returning an error. You are returning 'err' which is 0 at this point. So, at the very least, this code is (very) misleading since it suggests that it would return some error (as saved in the 'err' variable) when it doesn't.

Guenter

Quoted 9 lines

Oh! Right I see it now, I'm sorry, I just kept skipping over it somehow.

So I should change to:
    power = read_screenpad_backlight_power(asus); if (power < 0)
        return power;

Is that acceptable?

That depends on what the code is supposed to do. Right now it is "If read_screenpad_backlight_power() returns -ENODEV, stop and return no error (let the rest of the code continue). If it returns another error, return it".
Changing the code as suggested above changes the semantics to "If read_screenpad_backlight_power() returns an error, always return it".

Looking at the patch, I don't have a definite answer. asus_screenpad_init() happily registers the backlight if read_screenpad_backlight_power() returns -ENODEV. One could argue that the other functions should thus handle that situation gracefully as well, but read_screenpad_brightness() does return -ENODEV in that situation. I think you should decide how you want to handle that case and handle it consistently across all functions.

Either case, there is another problem in asus_screenpad_init():
If read_screenpad_brightness() fails, the function returns an error, but does not unregister the backlight device.

Guenter

author maintainer
#7 lore raw
Quoted 158 lines · Guenter Roeck
Quoted 132 lines · Luke Jones
Quoted 121 lines · Guenter Roeck
Quoted 115 lines · Luke Jones
Quoted 33 lines · Ilpo Järvinen
Quoted 17 lines · Luke D. Jones

Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some
high-end
ASUS laptops like the GX650P series and others.

These methods are utilised in a new backlight device named:
- asus_screenpad

---

  .../ABI/testing/sysfs-platform-asus-wmi       |   2 +-
  drivers/platform/x86/asus-wmi.c               | 132 
++++++++++++++++++
  drivers/platform/x86/asus-wmi.h               |   1 +
  include/linux/platform_data/x86/asus-wmi.h    |   4 +
  4 files changed, 138 insertions(+), 1 deletion(-)
Quoted 13 lines

diff --git a/Documentation/ABI/testing/sysfs-platform-asus-wmi
b/Documentation/ABI/testing/sysfs-platform-asus-wmi
index a77a004a1baa..df9817c6233a 100644
--- a/Documentation/ABI/testing/sysfs-platform-asus-wmi +++ b/Documentation/ABI/testing/sysfs-platform-asus-wmi
@@ -97,4 +97,4 @@ Contact: "Luke Jones" <[email protected]>
Description:
Enable an LCD response-time boost to reduce or remove
ghosting:
* 0 - Disable,
- * 1 - Enable
+ * 1 - Enable
\ No newline at end of file

Quoted 1 line

Spurious change?

Indeed it is. Not sure how that occurred.

Quoted 26 lines
Quoted 18 lines

diff --git a/drivers/platform/x86/asus-wmi.c
b/drivers/platform/x86/asus-wmi.c
index 1038dfdcdd32..0528eef02ef7 100644
--- a/drivers/platform/x86/asus-wmi.c
+++ b/drivers/platform/x86/asus-wmi.c
@@ -200,6 +200,7 @@ struct asus_wmi {

      struct input_dev *inputdev;
      struct backlight_device *backlight_device;
 +    struct backlight_device *screenpad_backlight_device;
      struct platform_device *platform_device;

      struct led_classdev wlan_led;
 @@ -3208,6 +3209,129 @@ static int is_display_toggle(int code)
      return 0;

}

Quoted 7 lines

+/* Screenpad backlight */
+
+static int read_screenpad_backlight_power(struct asus_wmi
*asus)
+{
+ int ret = asus_wmi_get_devstate_simple(asus,
ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 2 lines

Please move this to own line because now you have the extra newline in between the call and error handling.

I don't understand what you mean sorry. Remove the new line or:
int ret;
ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 42 lines
Quoted 41 lines

+
+ if (ret < 0)
+ return ret;
+ /* 1 == powered */
+ return ret ? FB_BLANK_UNBLANK : FB_BLANK_POWERDOWN;
+}
+
+static int read_screenpad_brightness(struct backlight_device
*bd)
+{

 +    struct asus_wmi *asus = bl_get_data(bd);
 +    u32 retval;
 +    int err;

+
+ err = read_screenpad_backlight_power(asus);
+ if (err < 0)
+ return err;
+ /* The device brightness can only be read if powered, so
return stored */
+ if (err == FB_BLANK_POWERDOWN)
+ return asus->driver->screenpad_brightness;
+
+ err = asus_wmi_get_devstate(asus,
ASUS_WMI_DEVID_SCREENPAD_LIGHT, &retval);
+ if (err < 0)
+ return err;
+
+ return retval & ASUS_WMI_DSTS_BRIGHTNESS_MASK;
+}
+
+static int update_screenpad_bl_status(struct backlight_device
*bd)
+{

 +    struct asus_wmi *asus = bl_get_data(bd);
 +    int power, err = 0;
 +    u32 ctrl_param;

+
+ power = read_screenpad_backlight_power(asus);
+ if (power == -ENODEV)
+ return err;

Quoted 4 lines
Quoted 1 line

Just return 0. Or is there perhaps something wrong/missing here?

I thought the correct thing was to return any possible error state (here, anything less than 0 would be an error, right?)

Quoted 7 lines

Well, yes, but you are not returning an error. You are returning 'err' which is 0 at this point. So, at the very least, this code is (very) misleading since it suggests that it would return some error (as saved in the 'err' variable) when it doesn't.

Guenter

Quoted 9 lines

Oh! Right I see it now, I'm sorry, I just kept skipping over it somehow.

So I should change to:

     power = read_screenpad_backlight_power(asus);
     if (power < 0)
         return power;

Is that acceptable?

That depends on what the code is supposed to do. Right now it is "If read_screenpad_backlight_power() returns -ENODEV, stop and return no error (let the rest of the code continue). If it returns another error, return it".
Changing the code as suggested above changes the semantics to "If read_screenpad_backlight_power() returns an error, always return it".

Looking at the patch, I don't have a definite answer. asus_screenpad_init() happily registers the backlight if read_screenpad_backlight_power() returns -ENODEV. One could argue that the other functions should thus handle that situation gracefully as well, but read_screenpad_brightness() does return -ENODEV in that situation. I think you should decide how you want to handle that case and handle it consistently across all functions.

Quoted 6 lines

Either case, there is another problem in asus_screenpad_init():
If read_screenpad_brightness() fails, the function returns an error, but does not unregister the backlight device.

Guenter

Thanks mate. I was working on this between my workload and getting a few users to test. My first priority was to get the thing working for them and as such I didn't put much thought in to errors and consistency.

I think since asus_screenpad_init() is not called unless the brightness WMI method exists, then it and the other functions should return all errors if the power WMI method fails at all since the device functionality is compromised. If there is a hardware change in this aspect we could revisit it then.

Quoted 3 lines

Either case, there is another problem in asus_screenpad_init():
If read_screenpad_brightness() fails, the function returns an error, but does not unregister the backlight device.

I wasn't entirely sure how to handle this. Mostly I followed what the existing backlight code was doing, I've now added a goto fail_screenpad; with:
fail_screenpad:

	if (asus->screenpad_backlight_device)
		asus_screenpad_exit(asus);

really I'm relying on others to guide me with this - I know I've got a fair few patches in these days but they've been mostly simple things except for TUF RGB, and I've had to learn a bunch of stuff as I go.

I'll await your response before I send in a V3.

Cheers,
Luke.

#8 lore raw
Quoted 154 lines · Luke Jones
Quoted 151 lines · Guenter Roeck
Quoted 121 lines · Luke Jones
Quoted 110 lines · Guenter Roeck
Quoted 104 lines · Luke Jones
Quoted 29 lines · Ilpo Järvinen
Quoted 15 lines · Luke D. Jones

 Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some high-end ASUS laptops like the GX650P series and others.

 These methods are utilised in a new backlight device named:
 - asus_screenpad

 ---
  .../ABI/testing/sysfs-platform-asus-wmi       |   2 +- drivers/platform/x86/asus-wmi.c               | 132 ++++++++++++++++++ drivers/platform/x86/asus-wmi.h               |   1 + include/linux/platform_data/x86/asus-wmi.h    |   4 +

  4 files changed, 138 insertions(+), 1 deletion(-)
Quoted 11 lines

 diff --git a/Documentation/ABI/testing/sysfs-platform-asus-wmi b/Documentation/ABI/testing/sysfs-platform-asus-wmi index a77a004a1baa..df9817c6233a 100644
 --- a/Documentation/ABI/testing/sysfs-platform-asus-wmi
 +++ b/Documentation/ABI/testing/sysfs-platform-asus-wmi
 @@ -97,4 +97,4 @@ Contact:    "Luke Jones" <[email protected]>
  Description:
          Enable an LCD response-time boost to reduce or remove ghosting:
              * 0 - Disable,
 -            * 1 - Enable
 +            * 1 - Enable
 \ No newline at end of file

Quoted 1 line

Spurious change?

Indeed it is. Not sure how that occurred.

Quoted 17 lines
Quoted 17 lines

 diff --git a/drivers/platform/x86/asus-wmi.c b/drivers/platform/x86/asus-wmi.c index 1038dfdcdd32..0528eef02ef7 100644
 --- a/drivers/platform/x86/asus-wmi.c
 +++ b/drivers/platform/x86/asus-wmi.c
 @@ -200,6 +200,7 @@ struct asus_wmi {

      struct input_dev *inputdev;
      struct backlight_device *backlight_device; +    struct backlight_device *screenpad_backlight_device; struct platform_device *platform_device;

      struct led_classdev wlan_led;
 @@ -3208,6 +3209,129 @@ static int is_display_toggle(int code) return 0;
  }

Quoted 8 lines
Quoted 5 lines

 +/* Screenpad backlight */
 +
 +static int read_screenpad_backlight_power(struct asus_wmi *asus)
 +{
 +    int ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Please move this to own line because now you have the extra newline in between the call and error handling.

I don't understand what you mean sorry. Remove the new line or:
int ret;
ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 38 lines
Quoted 37 lines

 +
 +    if (ret < 0)
 +        return ret;
 +    /* 1 == powered */
 +    return ret ? FB_BLANK_UNBLANK : FB_BLANK_POWERDOWN;
 +}
 +
 +static int read_screenpad_brightness(struct backlight_device *bd) +{
 +    struct asus_wmi *asus = bl_get_data(bd);
 +    u32 retval;
 +    int err;
 +
 +    err = read_screenpad_backlight_power(asus);
 +    if (err < 0)
 +        return err;
 +    /* The device brightness can only be read if powered, so return stored */ +    if (err == FB_BLANK_POWERDOWN)
 +        return asus->driver->screenpad_brightness;
 +
 +    err = asus_wmi_get_devstate(asus, ASUS_WMI_DEVID_SCREENPAD_LIGHT, &retval); +    if (err < 0)
 +        return err;
 +
 +    return retval & ASUS_WMI_DSTS_BRIGHTNESS_MASK;
 +}
 +
 +static int update_screenpad_bl_status(struct backlight_device *bd) +{
 +    struct asus_wmi *asus = bl_get_data(bd);
 +    int power, err = 0;
 +    u32 ctrl_param;
 +
 +    power = read_screenpad_backlight_power(asus);
 +    if (power == -ENODEV)
 +        return err;

Quoted 4 lines
Quoted 1 line

Just return 0. Or is there perhaps something wrong/missing here?

I thought the correct thing was to return any possible error state (here, anything less than 0 would be an error, right?)

Quoted 7 lines

Well, yes, but you are not returning an error. You are returning 'err' which is 0 at this point. So, at the very least, this code is (very) misleading since it suggests that it would return some error (as saved in the 'err' variable) when it doesn't.

Guenter

Quoted 9 lines

Oh! Right I see it now, I'm sorry, I just kept skipping over it somehow.

So I should change to:
     power = read_screenpad_backlight_power(asus); if (power < 0)
         return power;

Is that acceptable?

That depends on what the code is supposed to do. Right now it is "If read_screenpad_backlight_power() returns -ENODEV, stop and return no error (let the rest of the code continue). If it returns another error, return it".
Changing the code as suggested above changes the semantics to "If read_screenpad_backlight_power() returns an error, always return it".

Looking at the patch, I don't have a definite answer. asus_screenpad_init() happily registers the backlight if read_screenpad_backlight_power() returns -ENODEV. One could argue that the other functions should thus handle that situation gracefully as well, but read_screenpad_brightness() does return -ENODEV in that situation. I think you should decide how you want to handle that case and handle it consistently across all functions.

Either case, there is another problem in asus_screenpad_init():
If read_screenpad_brightness() fails, the function returns an error, but does not unregister the backlight device.

Quoted 8 lines
Quoted 2 lines

Guenter

Thanks mate. I was working on this between my workload and getting a few users to test. My first priority was to get the thing working for them and as such I didn't put much thought in to errors and consistency.

I think since asus_screenpad_init() is not called unless the brightness WMI method exists, then it and the other functions should return all errors if the power WMI method fails at all since the device functionality is compromised. If there is a hardware change in this aspect we could revisit it then.

That would suggest that asus_screenpad_init() should also abort on all errors and not assign a power of 'FB_BLANK_UNBLANK' if it is unreadable.

Quoted 4 lines
Quoted 3 lines

Either case, there is another problem in asus_screenpad_init():
If read_screenpad_brightness() fails, the function returns an error, but does not unregister the backlight device.

Quoted 9 lines

I wasn't entirely sure how to handle this. Mostly I followed what the existing backlight code was doing, I've now added a goto fail_screenpad; with:
fail_screenpad:
    if (asus->screenpad_backlight_device)
        asus_screenpad_exit(asus);

really I'm relying on others to guide me with this - I know I've got a fair few patches in these days but they've been mostly simple things except for TUF RGB, and I've had to learn a bunch of stuff as I go.

I'll await your response before I send in a V3.

Personally I'd first try to use devm_backlight_device_register(). As for error handling, the code would normally be something like

fail_screenpad:

	backlight_device_unregister(asus->screenpad_backlight_device);

or better

fail_screenpad:

	backlight_device_unregister(bd);

I don't know why you would want to check if asus->screenpad_backlight is NULL because the code would never be called with it being NULL.

Note that I don't see why

	asus->screenpad_backlight_device = NULL;

in asus_screenpad_exit() would be necessary.

Guenter

maintainer
#9 lore raw
In reply to Luke Jones
Quoted 25 lines · Luke Jones
Quoted 23 lines · Ilpo Järvinen
Quoted 20 lines · Luke D. Jones

Add support for the WMI methods used to turn off and adjust the brightness of the secondary "screenpad" device found on some high-end ASUS laptops like the GX650P series and others.

These methods are utilised in a new backlight device named:
- asus_screenpad

---

@@ -3208,6 +3209,129 @@ static int is_display_toggle(int code)
return 0;
}

+/* Screenpad backlight */
+
+static int read_screenpad_backlight_power(struct asus_wmi *asus) +{
+ int ret = asus_wmi_get_devstate_simple(asus,
ASUS_WMI_DEVID_SCREENPAD_POWER);

Quoted 6 lines
Quoted 2 lines

Please move this to own line because now you have the extra newline in between the call and error handling.

I don't understand what you mean sorry. Remove the new line or:
int ret;
ret = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_SCREENPAD_POWER);

Don't do:

int func()

{
	int ret = func();

	if (ret < 0)
		return ret;
	...
}

But do:

int func()

{
	int ret;

	ret = func();
	if (ret < 0)
		return ret;
	...
}

This keeps the error handling next to the actual call following the usual error handling pattern (natural logic grouping). The added clarity is well worth the one extra line required.

Quoted 10 lines
Quoted 10 lines
Quoted 9 lines

+static int update_screenpad_bl_status(struct backlight_device *bd) +{
+ struct asus_wmi *asus = bl_get_data(bd);
+ int power, err = 0;
+ u32 ctrl_param;
+
+ power = read_screenpad_backlight_power(asus);
+ if (power == -ENODEV)
+ return err;

Quoted 4 lines
Quoted 1 line

Just return 0. Or is there perhaps something wrong/missing here?

I thought the correct thing was to return any possible error state (here, anything less than 0 would be an error, right?)

I think this was covered already but here what I meant, use either:

	return 0;
because err is always 0 at that point, or:
	return power;

Depending on which is correct, I wasn't sure because you had this after it:

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

+ else if (power < 0)
+ return power;

...So I thought you might really intentionally wanted to return 0 there.

Signature · 1 line
 i.
#10 lore raw
In reply to Luke D. Jones

Hi Luke,

Quoted 13 lines · Luke D. Jones

Adds support for the screenpad(-plus) found on a few ASUS laptops that have a main 16:9 or 16:10 screen and a shorter screen below the main but above the keyboard. The support consists of:
- On off control
- Setting brightness from 0-255

There are some small quirks with this device when considering only the raw WMI methods:
1. The Off method can only switch the device off
2. Changing the brightness turns the device back on
3. To turn the device back on the brightness must be > 1
4. When the device is off the brightness can't be changed (so it is stored by the driver if device is off).
5. Booting with a value of 0 brightness (retained by bios) means the bios will set a value of > 0, < 15 which is far too dim and was unexpected by testers. The compromise was to set the brightness to 60 which is a usable brightness if the module init brightness was under 15.
6. When the device is off it is "unplugged"

Quoted 5 lines

All of the above points are addressed within the patch to create a good user experience and keep within user expectations.

Changelog:
- V2
- Complete refactor to use as a backlight device

Thank you on your work for this.

Unfortunately I did not get a chance to react to the v1 posting and the remarks to switch to using /sys/class/backlight there before you posted this v2.

Technically the remark to use /sys/class/backlight for this is completely correct. But due to the way how userspace uses /sys/class/backlight this is a problematic.

Userspace basically always assumes there is only 1 LCD panel and it then looks at /sys/class/backlight and picks 1 /sys/class/backlight entry and uses that for the brightness slider in the desktop-environment UI / system-menu as well as to handle brightness up/down keyboard hotkey presses.

In the (recent) past the kernel used to register e.g. both /sys/class/backlight/acpi_video0 and /sys/class/backlight/intel_backlight

For ACPI resp. direct hw control of the LCD panel backlight (so both control the same backlight, sometimes both work sometimes only 1 works).

Userspace uses the backlight-type to determine which backlight class to use, using (for GNOME, but I believe everywhere) the following preference order:

1. First look for "firmware" type backlight devices (like acpi_video0)
2. Then try "platform" type backlight devices
3. Last try "raw" type backlight devices

And to make things work the kernel has been hiding the "acpi_video0" entry in cases where it is known that we need the "raw" aka native type backlight.

Luke you seem to already be partly aware of this, because the patch now has this:

props.type = BACKLIGHT_RAW; /* ensure this bd is last to be picked */

but almost all modern laptops exclusively use the raw/native type for backlight control of the main LCD panel.

So now we end up with 2 "raw" type backlight devices and if e.g. gnome-settings-daemon picks the right one now sort of is left to luck.

Well that is not entirely true, at least gnome-settings-daemon prefers raw backlight devices where the parent has an "enabled" sysfs attribute (it expects the parent to be a drm_connector object) and where that enabled attribute reads as "enabled".

This is done for hybrid-gfx laptops where there already may be 2 raw backlight-class devices, 1 for each GPU but only 1 of the 2 drm_connectors going to the main LCD panel should actually show as enabled.

So typing all this out I guess we could go ahead with using the backlight class for this after all, but this relies on userspace preferring raw backlight-class devices with a drm_connector-object parent which show as being enabled.

Any userspace code which does not do the parent has an enabled attr reading "enabled" or a similar check will end up picking a random backlight class device as control for the main panel brightness which will not always end well. So this all is a bit fragile ...

And I'm not sure what is the best thing to do here.

Barnabás, Ilpo, Guenter, any comments on this ?

Regards,

Hans

p.s.

Note I'm working on allowing brightness control for multiple screens in a sane way, see:

https://lore.kernel.org/dri-devel/[email protected]/

The last few kernel-cycles I have landed a refactor/cleanup of the existing backlight code so that we only ever register 1 /sys/class/backlight entry for the main LCD panel, instead of having e.g. both acpi_video0 + intel_backlight and relying on userspace preferring acpi_video0 in that case.

And when I can find time for it I plan to implement the API in the linked RFC, which allows properly dealing with all this.

Luke, question how does the second/exta panel look from an outputting video to it pov ? Does it show up as an extra screen connected to a drm_connector on one of the GPUs. IOW can it be used with standard kernel-modesetting APIs ?

#11 lore raw

Hi,

Quoted 92 lines · Hans de Goede

Hi Luke,

Quoted 13 lines · Luke D. Jones

Adds support for the screenpad(-plus) found on a few ASUS laptops that have a main 16:9 or 16:10 screen and a shorter screen below the main but above the keyboard. The support consists of:
- On off control
- Setting brightness from 0-255

There are some small quirks with this device when considering only the raw WMI methods:
1. The Off method can only switch the device off
2. Changing the brightness turns the device back on
3. To turn the device back on the brightness must be > 1
4. When the device is off the brightness can't be changed (so it is stored by the driver if device is off).
5. Booting with a value of 0 brightness (retained by bios) means the bios will set a value of > 0, < 15 which is far too dim and was unexpected by testers. The compromise was to set the brightness to 60 which is a usable brightness if the module init brightness was under 15.
6. When the device is off it is "unplugged"

Quoted 5 lines

All of the above points are addressed within the patch to create a good user experience and keep within user expectations.

Changelog:
- V2
- Complete refactor to use as a backlight device

Thank you on your work for this.

Unfortunately I did not get a chance to react to the v1 posting and the remarks to switch to using /sys/class/backlight there before you posted this v2.

Technically the remark to use /sys/class/backlight for this is completely correct. But due to the way how userspace uses /sys/class/backlight this is a problematic.

Userspace basically always assumes there is only 1 LCD panel and it then looks at /sys/class/backlight and picks 1 /sys/class/backlight entry and uses that for the brightness slider in the desktop-environment UI / system-menu as well as to handle brightness up/down keyboard hotkey presses.

In the (recent) past the kernel used to register e.g. both /sys/class/backlight/acpi_video0 and /sys/class/backlight/intel_backlight

For ACPI resp. direct hw control of the LCD panel backlight (so both control the same backlight, sometimes both work sometimes only 1 works).

Userspace uses the backlight-type to determine which backlight class to use, using (for GNOME, but I believe everywhere) the following preference order:

1. First look for "firmware" type backlight devices (like acpi_video0)
2. Then try "platform" type backlight devices
3. Last try "raw" type backlight devices

And to make things work the kernel has been hiding the "acpi_video0" entry in cases where it is known that we need the "raw" aka native type backlight.

Luke you seem to already be partly aware of this, because the patch now has this:

props.type = BACKLIGHT_RAW; /* ensure this bd is last to be picked */

but almost all modern laptops exclusively use the raw/native type for backlight control of the main LCD panel.

So now we end up with 2 "raw" type backlight devices and if e.g. gnome-settings-daemon picks the right one now sort of is left to luck.

Well that is not entirely true, at least gnome-settings-daemon prefers raw backlight devices where the parent has an "enabled" sysfs attribute (it expects the parent to be a drm_connector object) and where that enabled attribute reads as "enabled".

This is done for hybrid-gfx laptops where there already may be 2 raw backlight-class devices, 1 for each GPU but only 1 of the 2 drm_connectors going to the main LCD panel should actually show as enabled.

So typing all this out I guess we could go ahead with using the backlight class for this after all, but this relies on userspace preferring raw backlight-class devices with a drm_connector-object parent which show as being enabled.

Any userspace code which does not do the parent has an enabled attr reading "enabled" or a similar check will end up picking a random backlight class device as control for the main panel brightness which will not always end well. So this all is a bit fragile ...

Quoted 3 lines

And I'm not sure what is the best thing to do here.

Barnabás, Ilpo, Guenter, any comments on this ?

Hmm, no comments from anyone on the potential problems of using /sys/class/backlight for this causing potential userspace confusion since normally /sys/class/backlight devices control the main LCD brightness ?

Luke do you have any thoughts on this yourself ?

And can you answer this question please ? :

Quoted 5 lines

Luke, question how does the second/exta panel look from an outputting video to it pov ? Does it show up as an extra screen connected to a drm_connector on one of the GPUs. IOW can it be used with standard kernel-modesetting APIs ?

Regards,

Hans

author maintainer
#12 lore raw
Quoted 46 lines · Hans de Goede

Hi,

Quoted 43 lines · Hans de Goede

Hi Luke,

Quoted 17 lines · Luke D. Jones

Adds support for the screenpad(-plus) found on a few ASUS laptops
that have a main 16:9 or 16:10 screen and a shorter screen below the main but above the keyboard.
The support consists of:
- On off control
- Setting brightness from 0-255

There are some small quirks with this device when considering only
the raw WMI methods:
1. The Off method can only switch the device off
2. Changing the brightness turns the device back on
3. To turn the device back on the brightness must be > 1
4. When the device is off the brightness can't be changed (so it
is stored by the driver if device is off).
5. Booting with a value of 0 brightness (retained by bios) means
the bios will set a value of > 0, < 15 which is far too dim and was unexpected by testers. The compromise was to set the brightness to 60 which is a usable brightness if the module init brightness was under 15.
6. When the device is off it is "unplugged"

Quoted 6 lines

All of the above points are addressed within the patch to create a
good user experience and keep within user expectations.

Changelog:
- V2
- Complete refactor to use as a backlight device

Thank you on your work for this.

Unfortunately I did not get a chance to react to the v1 posting and the remarks to switch to using /sys/class/backlight there before you posted this v2.

Technically the remark to use /sys/class/backlight for this is completely correct. But due to the way how userspace uses /sys/class/backlight this is a problematic.

Userspace basically always assumes there is only 1 LCD panel and it then looks at /sys/class/backlight and picks 1 /sys/class/backlight entry and uses that for the brightness slider in the desktop-environment UI / system-menu as well as to handle brightness up/down keyboard hotkey presses.

IMO, desktops need to adjust this expectation and start offering controls for all possible screens. This would open up the possibility of setting brightness of modern external screens also. And then they should use the "Primary display" brightness controls, or at least offer an option to set which is controlled.

Quoted 28 lines
Quoted 28 lines

In the (recent) past the kernel used to register e.g. both /sys/class/backlight/acpi_video0 and /sys/class/backlight/intel_backlight

For ACPI resp. direct hw control of the LCD panel backlight (so both control the same backlight, sometimes both work sometimes only 1 works).

Userspace uses the backlight-type to determine which backlight class to use, using (for GNOME, but I believe everywhere) the following preference order:

1. First look for "firmware" type backlight devices (like
acpi_video0)
2. Then try "platform" type backlight devices
3. Last try "raw" type backlight devices

And to make things work the kernel has been hiding the "acpi_video0" entry in cases where it is known that we need the "raw" aka native type backlight.

Luke you seem to already be partly aware of this, because the patch now has this:

props.type = BACKLIGHT_RAW; /* ensure this bd is last to be picked
*/

Quoted 7 lines
Quoted 7 lines

but almost all modern laptops exclusively use the raw/native type for backlight control of the main LCD panel.

So now we end up with 2 "raw" type backlight devices and if e.g. gnome-settings-daemon picks the right one now sort of is left to luck.

In a test KDE at least picked the right one.

Quoted 6 lines
Quoted 6 lines

Well that is not entirely true, at least gnome-settings-daemon prefers raw backlight devices where the parent has an "enabled" sysfs attribute (it expects the parent to be a drm_connector object) and where that enabled attribute reads as "enabled".

Ah I see. Parent for screenpad is "platform", while the main is on igpu with parent "pci". I will paste some udev info at the end of this reply.

Quoted 22 lines
Quoted 18 lines

This is done for hybrid-gfx laptops where there already may be 2 raw backlight-class devices, 1 for each GPU but only 1 of the 2 drm_connectors going to the main LCD panel should actually show as enabled.

So typing all this out I guess we could go ahead with using the backlight class for this after all, but this relies on userspace preferring raw backlight-class devices with a drm_connector-object parent which show as being enabled.

Any userspace code which does not do the parent has an enabled attr reading "enabled" or a similar check will end up picking a random backlight class device as control for the main panel brightness which will not always end well. So this all is a bit fragile ...

Quoted 3 lines

And I'm not sure what is the best thing to do here.

Barnabás, Ilpo, Guenter, any comments on this ?

Quoted 15 lines

Hmm, no comments from anyone on the potential problems of using /sys/class/backlight for this causing potential userspace confusion since normally /sys/class/backlight devices control the main LCD brightness ?

Luke do you have any thoughts on this yourself ?

And can you answer this question please ? :

Quoted 5 lines

Luke, question how does the second/exta panel look from an outputting video to it pov ? Does it show up as an extra screen connected to a drm_connector on one of the GPUs. IOW can it be used with standard kernel-modesetting APIs ?

Hi Hans, sorry about delay in response, just been tied up with work.

As I don't actually have this kind of laptop I can't easily get info, but I can ask a few people in my discord for information. Is there anything in particular you would need to know? From my basic understanding some of the points are:

1. It does show as an actual additional screen
2. Internal wiring is unclear, when dispaly MUX is switched to dgpu the screen is still detected but not drawn to
3. Point 2 is actually more uncertain as it seems only wayland had this issue? I will get more info.

So I think now is probably a good time to raise a particular issue I've encountered with the last two years: the display MUX.

As I understand it now, there are two types of new MUX - the manual switch, and the newer "Advanced Optimus" automatic switch. The issues I have are with the manual switch since I've not encountered the advanced optimus yet.

When the switch is. uh. switched. the dgpu drives the internal display, and I expect that since the display is now detected through the dgpu, this is why the dgpu is kept awake to drive it. But, the igpu is also still active, and because of this the initial boot from grub to display-manager is a black screen including tty. This means anyone with an encrypted drive will never see the prompt and they believe they have a failed boot. I don't know what to do about this?

What I would love is somehow to either disable the igpu in kernel if the MUX is toggled, or to change which device is the primary. Do you have any thoughts on where I should start on this?

An additional problem: boot_vga property of display adaptors. I've been using this as a first-stage check in supergfxctl to determine if there was a switch, but it is never ever reliable - sometimes it changes, sometimes it is entirely blank (using udev to fetch properties). And then I need to use a combination of checks to determine state. So this boot_vga seems to always be available but is practically unusable.

UDEV info dumps:

Device {
initialized: true,
device_major_minor_number: None,
system_path:
"/sys/devices/pci0000:00/0000:00:08.1/0000:09:00.0/backlight/amdgpu_bl1",
device_path:
"/devices/pci0000:00/0000:00:08.1/0000:09:00.0/backlight/amdgpu_bl1",
device_node: None,
subsystem_name: Some(
"backlight",
),
system_name: "amdgpu_bl1",
instance_number: Some(

       1,
   ),
   device_type: None,
   driver: None,
   action: None,
   parent: Some(
       Device {
           initialized: true,
           device_major_minor_number: None,
           system_path: 
"/sys/devices/pci0000:00/0000:00:08.1/0000:09:00.0",
           device_path: 
"/devices/pci0000:00/0000:00:08.1/0000:09:00.0",
           device_node: None,
           subsystem_name: Some(
               "pci",
           ),
           system_name: "0000:09:00.0",
           instance_number: Some(
               0,
           ),
           device_type: None,
           driver: Some(
               "amdgpu",
           ),
           action: None,
           parent: Some(
               Device {
                   initialized: true,
                   device_major_minor_number: None,
                   system_path: "/sys/devices/pci0000:00/0000:00:08.1",
                   device_path: "/devices/pci0000:00/0000:00:08.1",
                   device_node: None,
                   subsystem_name: Some(
                       "pci",
                   ),
                   system_name: "0000:00:08.1",
                   instance_number: Some(
                       1,
                   ),
                   device_type: None,
                   driver: Some(
                       "pcieport",
                   ),
                   action: None,
                   parent: Some(
                       Device {
                           initialized: false,
                           device_major_minor_number: None,
                           system_path: "/sys/devices/pci0000:00",
                           device_path: "/devices/pci0000:00",
                           device_node: None,
                           subsystem_name: None,
                           system_name: "pci0000:00",
                           instance_number: Some(
                               0,
                           ),
                           device_type: None,
                           driver: None,
                           action: None,
                           parent: None,
                       },
                   ),
               },
           ),
       },

),
}
[properties]
- "CURRENT_TAGS" ":systemd:seat:"
- "DEVPATH"
"/devices/pci0000:00/0000:00:08.1/0000:09:00.0/backlight/amdgpu_bl1"
- "DMI_FAMILY" "ROG Zephyrus Duo 16"
- "DMI_VENDOR" "ASUSTeK COMPUTER INC."
- "ID_FOR_SEAT" "backlight-pci-0000_09_00_0"
- "ID_PATH" "pci-0000:09:00.0"
- "ID_PATH_TAG" "pci-0000_09_00_0"
- "NVME_HOST_IFACE" "none"
- "SUBSYSTEM" "backlight"
- "SYSTEMD_WANTS" "systemd-backlight@backlight:amdgpu_bl1.service"
- "TAGS" ":systemd:seat:"
- "USEC_INITIALIZED" "6189554"
[attributes]
- "actual_brightness" ""
- "bl_power" ""
- "brightness" ""
- "device" ""
- "max_brightness" ""
- "power/autosuspend_delay_ms" ""
- "power/control" ""
- "power/runtime_active_time" ""
- "power/runtime_status" ""
- "power/runtime_suspended_time" ""
- "scale" ""
- "subsystem" ""
- "type" ""
- "uevent" ""

Device {
initialized: true,
device_major_minor_number: None,
system_path:
"/sys/devices/platform/asus-nb-wmi/backlight/asus_screenpad",
device_path:
"/devices/platform/asus-nb-wmi/backlight/asus_screenpad",
device_node: None,
subsystem_name: Some(
"backlight",
),
system_name: "asus_screenpad",
instance_number: None,
device_type: None,
driver: None,
action: None,
parent: Some(

       Device {
           initialized: true,
           device_major_minor_number: None,
           system_path: "/sys/devices/platform/asus-nb-wmi",
           device_path: "/devices/platform/asus-nb-wmi",
           device_node: None,
           subsystem_name: Some(
               "platform",
           ),
           system_name: "asus-nb-wmi",
           instance_number: None,
           device_type: None,
           driver: Some(
               "asus-nb-wmi",
           ),
           action: None,
           parent: Some(
               Device {
                   initialized: false,
                   device_major_minor_number: None,
                   system_path: "/sys/devices/platform",
                   device_path: "/devices/platform",
                   device_node: None,
                   subsystem_name: None,
                   system_name: "platform",
                   instance_number: None,
                   device_type: None,
                   driver: None,
                   action: None,
                   parent: None,
               },
           ),
       },

),
}
[properties]
- "CURRENT_TAGS" ":systemd:seat:"
- "DEVPATH" "/devices/platform/asus-nb-wmi/backlight/asus_screenpad"
- "DMI_FAMILY" "ROG Zephyrus Duo 16"
- "DMI_VENDOR" "ASUSTeK COMPUTER INC."
- "ID_FOR_SEAT" "backlight-platform-asus-nb-wmi"
- "ID_PATH" "platform-asus-nb-wmi"
- "ID_PATH_TAG" "platform-asus-nb-wmi"
- "NVME_HOST_IFACE" "none"
- "SUBSYSTEM" "backlight"
- "SYSTEMD_WANTS"
"systemd-backlight@backlight:asus_screenpad.service"
- "TAGS" ":systemd:seat:"
- "USEC_INITIALIZED" "6323833"
[attributes]
- "actual_brightness" ""
- "bl_power" ""
- "brightness" ""
- "device" ""
- "max_brightness" ""
- "power/autosuspend_delay_ms" ""
- "power/control" ""
- "power/runtime_active_time" ""
- "power/runtime_status" ""
- "power/runtime_suspended_time" ""
- "scale" ""
- "subsystem" ""
- "type" ""
- "uevent" ""

Device {
initialized: true,
device_major_minor_number: None,
system_path:
"/sys/devices/pci0000:00/0000:00:08.1/0000:09:00.0/drm/card1/card1-DP-1",
device_path:
"/devices/pci0000:00/0000:00:08.1/0000:09:00.0/drm/card1/card1-DP-1",
device_node: None,
subsystem_name: Some(

       "drm",
   ),
   system_name: "card1-DP-1",
   instance_number: Some(
       1,
   ),
   device_type: Some(
       "drm_connector",
   ),
   driver: None,
   action: None,
   parent: Some(
       Device {
           initialized: true,
           device_major_minor_number: Some(
               57857,
           ),
           system_path: 
"/sys/devices/pci0000:00/0000:00:08.1/0000:09:00.0/drm/card1",
           device_path: 
"/devices/pci0000:00/0000:00:08.1/0000:09:00.0/drm/card1",
           device_node: Some(
               "/dev/dri/card1",
           ),
           subsystem_name: Some(
               "drm",
           ),
           system_name: "card1",
           instance_number: Some(
               1,
           ),
           device_type: Some(
               "drm_minor",
           ),
           driver: None,
           action: None,
           parent: Some(
               Device {
                   initialized: true,
                   device_major_minor_number: None,
                   system_path: 
"/sys/devices/pci0000:00/0000:00:08.1/0000:09:00.0",
                   device_path: 
"/devices/pci0000:00/0000:00:08.1/0000:09:00.0",
                   device_node: None,
                   subsystem_name: Some(
                       "pci",
                   ),
                   system_name: "0000:09:00.0",
                   instance_number: Some(
                       0,
                   ),
                   device_type: None,
                   driver: Some(
                       "amdgpu",
                   ),
                   action: None,
                   parent: Some(
                       Device {
                           initialized: true,
                           device_major_minor_number: None,
                           system_path: 
"/sys/devices/pci0000:00/0000:00:08.1",
                           device_path: 
"/devices/pci0000:00/0000:00:08.1",
                           device_node: None,
                           subsystem_name: Some(
                               "pci",
                           ),
                           system_name: "0000:00:08.1",
                           instance_number: Some(
                               1,
                           ),
                           device_type: None,
                           driver: Some(
                               "pcieport",
                           ),
                           action: None,
                           parent: Some(
                               Device {
                                   initialized: false,
                                   device_major_minor_number: None,
                                   system_path: 
"/sys/devices/pci0000:00",
                                   device_path: "/devices/pci0000:00",
                                   device_node: None,
                                   subsystem_name: None,
                                   system_name: "pci0000:00",
                                   instance_number: Some(
                                       0,
                                   ),
                                   device_type: None,
                                   driver: None,
                                   action: None,
                                   parent: None,
                               },
                           ),
                       },
                   ),
               },
           ),
       },

),
}
[properties]
- "CURRENT_TAGS" ":master-of-seat:seat:"
- "DEVPATH"
"/devices/pci0000:00/0000:00:08.1/0000:09:00.0/drm/card1/card1-DP-1"
- "DEVTYPE" "drm_connector"
- "DMI_FAMILY" "ROG Zephyrus Duo 16"
- "DMI_VENDOR" "ASUSTeK COMPUTER INC."
- "ID_FOR_SEAT" "drm-pci-0000_09_00_0"
- "ID_PATH" "pci-0000:09:00.0"
- "ID_PATH_TAG" "pci-0000_09_00_0"
- "SUBSYSTEM" "drm"
- "TAGS" ":master-of-seat:seat:"
- "USEC_INITIALIZED" "6196005"
[attributes]
- "ddc" ""
- "device" ""
- "dpms" ""
- "edid" ""
- "enabled" ""
- "modes" ""
- "power/autosuspend_delay_ms" ""
- "power/control" ""
- "power/runtime_active_time" ""
- "power/runtime_status" ""
- "power/runtime_suspended_time" ""
- "status" ""
- "subsystem" ""
- "uevent" ""

Quoted 1 line
#13 lore raw

Hi Luke,

Quoted 1 line · Luke Jones

On Mon, May 15 2023 at 14:39:10 +0200, Hans de Goede <[email protected]> wrote:

<snip>

Quoted 10 lines
Quoted 10 lines
Quoted 10 lines

 Thank you on your work for this.

 Unfortunately I did not get a chance to react to the v1 posting and the remarks to switch to using /sys/class/backlight there before you posted this v2.

 Technically the remark to use /sys/class/backlight for this is completely correct. But due to the way how userspace uses /sys/class/backlight this is a problematic.

Quoted 8 lines
Quoted 6 lines
Quoted 6 lines

 Userspace basically always assumes there is only 1 LCD panel and it then looks at /sys/class/backlight and picks 1 /sys/class/backlight entry and uses that for the brightness slider in the desktop-environment UI / system-menu as well as to handle brightness up/down keyboard hotkey presses.

IMO, desktops need to adjust this expectation and start offering controls for all possible screens. This would open up the possibility of setting brightness of modern external screens also. And then they should use the "Primary display" brightness controls, or at least offer an option to set which is controlled.

Right this is what the proposal at:

https://lore.kernel.org/dri-devel/[email protected]/

is about. ATM userspace cannot reliably determine which /sys/class/backlight device belongs to which screen / video-output . So before desktops can offer this functionality we first need to fix the kernel <-> userspace APIs for this.

<snip>

Quoted 6 lines
Quoted 4 lines
Quoted 4 lines

 So now we end up with 2 "raw" type backlight devices and if e.g. gnome-settings-daemon picks the right one now sort of is left to luck.

In a test KDE at least picked the right one.

That is good to know I'm still not entirely convinced using /sys/class/backlight for this is a good idea though.

See below.

Quoted 7 lines
Quoted 5 lines
Quoted 5 lines

 Well that is not entirely true, at least gnome-settings-daemon prefers raw backlight devices where the parent has an "enabled" sysfs attribute (it expects the parent to be a drm_connector object) and where that enabled attribute reads as "enabled".

Ah I see. Parent for screenpad is "platform", while the main is on igpu with parent "pci". I will paste some udev info at the end of this reply.

Actually for the backlight-device on the iGPU the parent should be a drm-connector for the eDP (and the parent of that is the iGPU PCI device). Note I did not check the udev dump.

<snip>

Quoted 7 lines
Quoted 6 lines
Quoted 5 lines

 Luke, question how does the second/exta panel look from an outputting video to it pov ?  Does it show up as an extra screen connected to a drm_connector on one of the GPUs. IOW can it be used with standard kernel-modesetting APIs ?

Quoted 7 lines

Hi Hans, sorry about delay in response, just been tied up with work.

As I don't actually have this kind of laptop I can't easily get info, but I can ask a few people in my discord for information. Is there anything in particular you would need to know? From my basic understanding some of the points are:

1. It does show as an actual additional screen
2. Internal wiring is unclear, when dispaly MUX is switched to dgpu the screen is still detected but not drawn to
3. Point 2 is actually more uncertain as it seems only wayland had this issue? I will get more info.

Right, so I think we first need to better understand the interactions between the WMI calls you are making and the drm/kms interface.

Question 1:

If you turn the second screen off through WMI, does it get seen as disconnected by the drm/kms driver then. Or does the drm/kms driver just go on treating it as an extra connected display, still drawing now no longer visible content to it ?

IOW does the desktop environment's monitor-config panel no longer show the extra display after disabling it through WMI?

The best way to check this is look under /sys/class/drm and find out which /sys/class/drm/card#-<conn-type>-# entry belongs to the extra panel. Step 1 check for all card#-<conn-type>-# entries where status returns connected, e.g. :

[hans@shalem ~]$ cat /sys/class/drm/card1-DP-1/status connected

Step 2: for the connected ones cat the modes, e.g.:

[hans@shalem ~]$ cat /sys/class/drm/card1-DP-1/modes 1920x1080
1600x1200
...

And find the one which matches with the resolution of the extra panel (the one which does not match with the resolution of the main panel).

Then turn the extra panel of through WMI and cat the status attribute again. If that still reads connected then that means the desktop environment keeps seeing an extra display output which is not ideal. This will e.g. cause any windows which were on the extra panel to stay there, even though they are no longer visible.

Question 2:

If you turn the second screen off through drm/kms, using the desktop environments monitor config panel does this also turn off the backlight ?

After disabling the screen in the desktop environments monitor config check that the enabled attribute, e.g. cat /sys/class/drm/card1-DP-1/enabled shows disabled and after verifying this look at the extra screen in a dark room, do you see any backlight bleed indicating the backlight is still on?

We really want the backlight on/off state and the drm-connector enabled state to match. My proposal from above will allow this once implemented. Until we can hook this all up nicely I think it might be better to just go with the custom sysfs attributes from your v1 patch rather then adding a /sys/class/backlight device for this.

Quoted 5 lines

So I think now is probably a good time to raise a particular issue I've encountered with the last two years: the display MUX.

As I understand it now, there are two types of new MUX - the manual switch, and the newer "Advanced Optimus" automatic switch. The issues I have are with the manual switch since I've not encountered the advanced optimus yet.

When the switch is. uh. switched. the dgpu drives the internal display, and I expect that since the display is now detected through the dgpu, this is why the dgpu is kept awake to drive it. But, the igpu is also still active, and because of this the initial boot from grub to display-manager is a black screen including tty. This means anyone with an encrypted drive will never see the prompt and they believe they have a failed boot. I don't know what to do about this?

Is this with EFI booting or with classic BIOS boot? With EFI booting the EFIFB should be put on the right GPU by the firmware. So I suspect this is with classic BIOS boot?

I think the best thing to do here is to just use EFI on machines like this. That or put grub in text mode so that it makes BIOS calls to display text. Using GRUB_TERMINAL_OUTPUT=gfxterm combined with classic BIOS booting will make grub try to directly drive the gfx card itself and I'm not surprised that it gets that wrong in this case.

Note I think that just using EFI is prefered over switching grub to GRUB_TERMINAL_OUTPUT=console. I would expect GRUB_TERMINAL_OUTPUT=console to also work but I'm not sure. I don't think that the classic BIOS boot stuff is still tested by laptop vendors and esp. not tested with non standard BIOS settings ...

Quoted 1 line

What I would love is somehow to either disable the igpu in kernel if the MUX is toggled, or to change which device is the primary. Do you have any thoughts on where I should start on this?

Not really, on the hybrid gfx devices which I have when optimus is disabled in the BIOS, muxing the main LCD to the Nvidia GPU the iGPU gets disabled by the BIOS.

If the iGPU in these models does not get disabled then I guess it is still needed for some connectors, e.g. maybe for displays connected to one of the thunderbolt ports ?

Or maybe it is left on now a days for things like Intel quicksync ?

Quoted 1 line

An additional problem: boot_vga property of display adaptors. I've been using this as a first-stage check in supergfxctl to determine if there was a switch, but it is never ever reliable - sometimes it changes, sometimes it is entirely blank (using udev to fetch properties). And then I need to use a combination of checks to determine state. So this boot_vga seems to always be available but is practically unusable.

I'm afraid I cannot really help here. I think most of these laptops ship in Optimus mode (so both GPUs enabled) by default. And the non optimus mode is likely only tested under certain circumstances so there are going to be firmware bugs here. And Linux' code for detecting this likely also has issues of its own. Combine the 2 and you get lots of "fun".

I guess this is also what trips up grub. I wonder if this is better / more reliable under EFI mode though? Esp. since that is what vendors actually QA/test.

Regards,

Hans

author maintainer
#14 lore raw
Quoted 98 lines · Hans de Goede

Hi Luke,

Quoted 2 lines · Luke Jones

On Mon, May 15 2023 at 14:39:10 +0200, Hans de Goede <[email protected]> wrote:

<snip>

Quoted 19 lines
Quoted 12 lines
Quoted 12 lines

 Thank you on your work for this.

 Unfortunately I did not get a chance to react to the v1 posting and
 the remarks to switch to using /sys/class/backlight there before you
 posted this v2.

 Technically the remark to use /sys/class/backlight for this is completely correct. But due to the way how userspace uses /sys/class/backlight this is a problematic.

Quoted 6 lines
Quoted 6 lines

 Userspace basically always assumes there is only 1 LCD panel and it then looks at /sys/class/backlight and picks 1 /sys/class/backlight entry and uses that for the brightness slider in the desktop-environment UI / system-menu as well as to handle brightness up/down keyboard hotkey presses.

Quoted 5 lines

IMO, desktops need to adjust this expectation and start offering controls for all possible screens. This would open up the possibility of setting brightness of modern external screens also. And then they should use the "Primary display" brightness controls, or at least offer an option to set which is controlled.

Right this is what the proposal at:

https://lore.kernel.org/dri-devel/[email protected]/

is about. ATM userspace cannot reliably determine which /sys/class/backlight device belongs to which screen / video-output . So before desktops can offer this functionality we first need to fix the kernel <-> userspace APIs for this.

<snip>

Quoted 6 lines
Quoted 4 lines
Quoted 4 lines

 So now we end up with 2 "raw" type backlight devices and if e.g. gnome-settings-daemon picks the right one now sort of is left to luck.

In a test KDE at least picked the right one.

That is good to know I'm still not entirely convinced using /sys/class/backlight for this is a good idea though.

See below.

Quoted 10 lines
Quoted 6 lines
Quoted 6 lines

 Well that is not entirely true, at least gnome-settings-daemon prefers raw backlight devices where the parent has an "enabled"
 sysfs attribute (it expects the parent to be a drm_connector object) and where that enabled attribute reads as "enabled".

Ah I see. Parent for screenpad is "platform", while the main is on igpu with parent "pci". I will paste some udev info at the end of this reply.

Actually for the backlight-device on the iGPU the parent should be a drm-connector for the eDP (and the parent of that is the iGPU PCI device). Note I did not check the udev dump.

<snip>

Quoted 15 lines
Quoted 6 lines
Quoted 5 lines

 Luke, question how does the second/exta panel look from an outputting video to it pov ?  Does it show up as an extra screen connected to a drm_connector on one of the GPUs. IOW can it be used with standard kernel-modesetting APIs ?

Hi Hans, sorry about delay in response, just been tied up with work.

As I don't actually have this kind of laptop I can't easily get info, but I can ask a few people in my discord for information. Is there anything in particular you would need to know? From my basic understanding some of the points are:

Quoted 5 lines

1. It does show as an actual additional screen
2. Internal wiring is unclear, when dispaly MUX is switched to dgpu the screen is still detected but not drawn to
3. Point 2 is actually more uncertain as it seems only wayland had this issue? I will get more info.

Right, so I think we first need to better understand the interactions between the WMI calls you are making and the drm/kms interface.

Quoted 6 lines

Question 1:

If you turn the second screen off through WMI, does it get seen as disconnected by the drm/kms driver then. Or does the drm/kms driver just go on treating it as an extra connected display, still drawing now no longer visible content to it ?

It is most certainly viewed as disconnected.

Quoted 2 lines

IOW does the desktop environment's monitor-config panel no longer show the extra display after disabling it through WMI?

That is correct, it is no-longer a connected and visible display

Quoted 9 lines

The best way to check this is look under /sys/class/drm and find out which /sys/class/drm/card#-<conn-type>-# entry belongs to the extra panel. Step 1 check for all card#-<conn-type>-# entries where status returns connected, e.g. :

[hans@shalem ~]$ cat /sys/class/drm/card1-DP-1/status connected

On disable the status does change to:
cat /sys/class/drm/card1-DP-5/enabled
disabled

Quoted 17 lines

Step 2: for the connected ones cat the modes, e.g.:

[hans@shalem ~]$ cat /sys/class/drm/card1-DP-1/modes 1920x1080
1600x1200
...

And find the one which matches with the resolution of the extra panel (the one which does not match with the resolution of the main panel).

Then turn the extra panel of through WMI and cat the status attribute again. If that still reads connected then that means the desktop environment keeps seeing an extra display output which is not ideal. This will e.g. cause any windows which were on the extra panel to stay there, even though they are no longer visible.

Quoted 5 lines

Question 2:

If you turn the second screen off through drm/kms, using the desktop environments monitor config panel does this also turn off the backlight ?

The screen is dark but there is still some backlight coming out of it. I think this means I need to add a small pre-off to the patch to ensure backlight is fully off when display is turned off.

Quoted 7 lines

After disabling the screen in the desktop environments monitor config check that the enabled attribute, e.g. cat /sys/class/drm/card1-DP- 1/enabled shows disabled and after verifying this look at the extra screen in a dark room, do you see any backlight bleed indicating the backlight is still  on?

Shows as disabled

Quoted 7 lines

We really want the backlight on/off state and the drm-connector enabled state to match. My proposal from above will allow this once implemented. Until we can hook this all up nicely I think it might be better to just go with the custom sysfs attributes from your v1 patch rather then adding a /sys/class/backlight device for this.

I would like to go with the backlight patch as it seems more likely I can adjust this without breaking userspace if required in future. The WMI controls behave as expected to.

Quoted 18 lines
Quoted 9 lines

So I think now is probably a good time to raise a particular issue I've encountered with the last two years: the display MUX.

As I understand it now, there are two types of new MUX - the manual switch, and the newer "Advanced Optimus" automatic switch. The issues I have are with the manual switch since I've not encountered the advanced optimus yet.

Quoted 8 lines

When the switch is. uh. switched. the dgpu drives the internal display, and I expect that since the display is now detected through the dgpu, this is why the dgpu is kept awake to drive it. But, the igpu is also still active, and because of this the initial boot from grub to display-manager is a black screen including tty. This means anyone with an encrypted drive will never see the prompt and they believe they have a failed boot. I don't know what to do about this?

Quoted 3 lines

Is this with EFI booting or with classic BIOS boot? With EFI booting the EFIFB should be put on the right GPU by the firmware. So I suspect this is with classic BIOS boot?

No this is with EFI boot always. I'm not even sure these machines still have the ability to boot oldschool bios style.

Quoted 12 lines

I think the best thing to do here is to just use EFI on machines like this. That or put grub in text mode so that it makes BIOS calls to display text. Using GRUB_TERMINAL_OUTPUT=gfxterm combined with classic BIOS booting will make grub try to directly drive the gfx card itself and I'm not surprised that it gets that wrong in this case.
Note I think that just using EFI is prefered over switching grub to GRUB_TERMINAL_OUTPUT=console. I would expect GRUB_TERMINAL_OUTPUT=console to also work but I'm not sure. I don't think that the classic BIOS boot stuff is still tested by laptop vendors and esp. not tested with non standard BIOS settings ...

The grub gfx mode is GRUB_TERMINAL_OUTPUT="console", fedora default in all cases here. Grub itself shows fine when the MUX mode is in dgpu mode (aka, internal display connected to dgpu).

Quoted 11 lines
Quoted 3 lines

What I would love is somehow to either disable the igpu in kernel if the MUX is toggled, or to change which device is the primary. Do you have any thoughts on where I should start on this?

Not really, on the hybrid gfx devices which I have when optimus is disabled in the BIOS, muxing the main LCD to the Nvidia GPU the iGPU gets disabled by the BIOS.

If the iGPU in these models does not get disabled then I guess it is still needed for some connectors, e.g. maybe for displays connected to one of the thunderbolt ports ?

Yeah seems likely. I'll have to actually check this (I have TB4 connected monitor).

Quoted 17 lines

Or maybe it is left on now a days for things like Intel quicksync ?

Quoted 7 lines

An additional problem: boot_vga property of display adaptors. I've been using this as a first-stage check in supergfxctl to determine if there was a switch, but it is never ever reliable - sometimes it changes, sometimes it is entirely blank (using udev to fetch properties). And then I need to use a combination of checks to determine state. So this boot_vga seems to always be available but is practically unusable.

I'm afraid I cannot really help here. I think most of these laptops ship in Optimus mode (so both GPUs enabled) by default. And the non optimus mode is likely only tested under certain circumstances so there are going to be firmware bugs here. And Linux' code for detecting this likely also has issues of its own. Combine the 2 and you get lots of "fun".

Quoted 3 lines

I guess this is also what trips up grub. I wonder if this is better / more reliable under EFI mode though? Esp. since that is what vendors actually QA/test.

As mentioned, the machines are all booting in EFI mode right from the start - the old mode (CMA?) doesn't seem to exist at all.

I really would like to find a solution here as it is tripping up a lot of new users.

Cheers,
Luke.

P.S> I will go ahead with the screen patch as it looks like this behaves as expected minus the need to turn off BL before turn off display. I will submit revision later in the week.

#15 lore raw

Hi Luke,

Quoted 1 line · Luke Jones

On Thu, 2023-05-25 at 13:09 +0200, Hans de Goede wrote:

<snip>

Quoted 11 lines
Quoted 9 lines

Right, so I think we first need to better understand the interactions between the WMI calls you are making and the drm/kms interface.

Question 1:

If you turn the second screen off through WMI, does it get seen as disconnected by the drm/kms driver then. Or does the drm/kms driver just go on treating it as an extra connected display, still drawing now no longer visible content to it ?

It is most certainly viewed as disconnected.

Ok, that is good.

Quoted 4 lines
Quoted 2 lines

IOW does the desktop environment's monitor-config panel no longer show the extra display after disabling it through WMI?

That is correct, it is no-longer a connected and visible display

Ack.

Quoted 5 lines
Quoted 5 lines

The best way to check this is look under /sys/class/drm and find out which /sys/class/drm/card#-<conn-type>-# entry belongs to the extra panel. Step 1 check for all card#-<conn-type>-# entries where status returns connected, e.g. :

Quoted 7 lines
Quoted 3 lines

[hans@shalem ~]$ cat /sys/class/drm/card1-DP-1/status connected

On disable the status does change to:
cat /sys/class/drm/card1-DP-5/enabled
disabled

Ok, that is good.

Quoted 19 lines
Quoted 19 lines

Step 2: for the connected ones cat the modes, e.g.:

[hans@shalem ~]$ cat /sys/class/drm/card1-DP-1/modes 1920x1080
1600x1200
...

And find the one which matches with the resolution of the extra panel (the one which does not match with the resolution of the main panel).

Then turn the extra panel of through WMI and cat the status attribute again. If that still reads connected then that means the desktop environment keeps seeing an extra display output which is not ideal. This will e.g. cause any windows which were on the extra panel to stay there, even though they are no longer visible.

Question 2:

Quoted 7 lines
Quoted 3 lines

If you turn the second screen off through drm/kms, using the desktop environments monitor config panel does this also turn off the backlight ?

The screen is dark but there is still some backlight coming out of it. I think this means I need to add a small pre-off to the patch to ensure backlight is fully off when display is turned off.

I'm afraid that this is not going to be easy to fix at the kernel level, we first need to tie backlight control to drm-connectors as I proposed (and plan to implement when I can make time):

https://lore.kernel.org/dri-devel/[email protected]/

Once that is in place we can simply make the drm-code call out to the backlight driver and have it turn the backlight off when disabling the output through the drm/kms interface.

Quoted 17 lines
Quoted 6 lines

After disabling the screen in the desktop environments monitor config check that the enabled attribute, e.g. cat /sys/class/drm/card1-DP- 1/enabled shows disabled and after verifying this look at the extra screen in a dark room, do you see any backlight bleed indicating the backlight is still  on?

Shows as disabled

Quoted 7 lines

We really want the backlight on/off state and the drm-connector enabled state to match. My proposal from above will allow this once implemented. Until we can hook this all up nicely I think it might be better to just go with the custom sysfs attributes from your v1 patch rather then adding a /sys/class/backlight device for this.

Quoted 3 lines

I would like to go with the backlight patch as it seems more likely I can adjust this without breaking userspace if required in future. The WMI controls behave as expected to.

Ok, lets go with the v2 which adds /sys/class/backlight support then.

I must warn you though if this does turn out to cause issues I'll have no choice but to revert it.

I must admit I've lost track a bit of the state of v2 during this discussion. Can I pick up v2 as is, or were there (other) remarks which need addressing and should I expect a v3 ?

####### Switch to (off-topic) GPU mux discussion ########

Quoted 17 lines
Quoted 17 lines
Quoted 16 lines

So I think now is probably a good time to raise a particular issue I've encountered with the last two years: the display MUX.

As I understand it now, there are two types of new MUX - the manual switch, and the newer "Advanced Optimus" automatic switch. The issues I have are with the manual switch since I've not encountered the advanced optimus yet.

When the switch is. uh. switched. the dgpu drives the internal display, and I expect that since the display is now detected through the dgpu, this is why the dgpu is kept awake to drive it. But, the igpu is also still active, and because of this the initial boot from grub to display-manager is a black screen including tty. This means anyone with an encrypted drive will never see the prompt and they believe they have a failed boot. I don't know what to do about this?

Quoted 6 lines
Quoted 3 lines

Is this with EFI booting or with classic BIOS boot? With EFI booting the EFIFB should be put on the right GPU by the firmware. So I suspect this is with classic BIOS boot?

No this is with EFI boot always. I'm not even sure these machines still have the ability to boot oldschool bios style.

Hmm, weird with EFI grub is just using the EFI text output protocol so what is happening here at the grub level is actually a bug in the firmware of the laptop(s)...

Quoted 12 lines
Quoted 11 lines

I think the best thing to do here is to just use EFI on machines like this. That or put grub in text mode so that it makes BIOS calls to display text. Using GRUB_TERMINAL_OUTPUT=gfxterm combined with classic BIOS booting will make grub try to directly drive the gfx card itself and I'm not surprised that it gets that wrong in this case.
Note I think that just using EFI is prefered over switching grub to GRUB_TERMINAL_OUTPUT=console. I would expect GRUB_TERMINAL_OUTPUT=console to also work but I'm not sure. I don't think that the classic BIOS boot stuff is still tested by laptop vendors and esp. not tested with non standard BIOS settings ...

Quoted 3 lines

The grub gfx mode is GRUB_TERMINAL_OUTPUT="console", fedora default in all cases here. Grub itself shows fine when the MUX mode is in dgpu mode (aka, internal display connected to dgpu).

Ah ok, so I misunderstood and the problem only happens *after* grub?

Have I understood that correctly?

And this is on Fedora with the nvidia binary driver ?

The problem then likely is that the nvidia binary driver is not in the initrd (which is by design since it may need to be rebuild on a driver update while the kernel is kept at the same version, so the initrd won't be rebuild).

So during the initrd there then is no kms driver to drive the internal display.

Normally plymouth falls back to using the efifb (through simpledrm) but that is after a pretty large timeout and I think this may not be happening here because plymouth maybe thinks there is a kms capable display connected to the iGPU for some reason (maybe the extra screenpad panel ?)

As a workaround you can tell plymouth to use the simpledrm kms device as soon as it becomes available instead of waiting for a native kms driver. To do this add "plymouth.use-simpledrm" to the kernel commandline. I think that this will work around the problem.

Quoted 3 lines

P.S> I will go ahead with the screen patch as it looks like this behaves as expected minus the need to turn off BL before turn off display. I will submit revision later in the week.

Ok, so that answers my question from above and I should wait for a v3 :)

Regards,

Hans

author maintainer
#16 lore raw

**snip**

Quoted 14 lines
Quoted 9 lines
Quoted 5 lines

Question 2:

If you turn the second screen off through drm/kms, using the desktop environments monitor config panel does this also turn off the backlight ?

The screen is dark but there is still some backlight coming out of it. I think this means I need to add a small pre-off to the patch to ensure backlight is fully off when display is turned off.

I'm afraid that this is not going to be easy to fix at the kernel level, we first need to tie backlight control to drm-connectors as I proposed (and plan to implement when I can make time):

Quoted 6 lines

https://lore.kernel.org/dri-devel/b61d3eeb-6213-afac-2e70-7b9791c86d2e@redha
t.com/

Once that is in place we can simply make the drm-code call out to the backlight driver and have it turn the backlight off when disabling the output through the drm/kms interface.

Okay cool. But until then I can set the screenpad to turn brightness off when it does the call to:
err = asus_wmi_set_devstate(ASUS_WMI_DEVID_SCREENPAD_POWER, 0, NULL); here I can also do before that call:
err = asus_wmi_set_devstate(ASUS_WMI_DEVID_SCREENPAD_LIGHT,ctrl_param, NULL);

Then when the patch you mention is done this can be removed.

**snip**

Quoted 4 lines
Quoted 3 lines

I would like to go with the backlight patch as it seems more likely I can adjust this without breaking userspace if required in future. The WMI controls behave as expected to.

Quoted 8 lines

Ok, lets go with the v2 which adds /sys/class/backlight support then.

I must warn you though if this does turn out to cause issues I'll have no choice but to revert it.

I must admit I've lost track a bit of the state of v2 during this discussion. Can I pick up v2 as is, or were there (other) remarks which need addressing and should I expect a v3 ?

There will be a V3. I don't anticipate any issues at all with this, and some folks have been using this patch with Gnome and KDE since V2 was submitted.

Quoted 2 lines

####### Switch to (off-topic) GPU mux discussion ########

**snip**

Quoted 18 lines
Quoted 12 lines
Quoted 11 lines

I think the best thing to do here is to just use EFI on machines like this. That or put grub in text mode so that it makes BIOS calls to display text. Using GRUB_TERMINAL_OUTPUT=gfxterm combined with classic BIOS booting will make grub try to directly drive the gfx card itself and I'm not surprised that it gets that wrong in this case.
Note I think that just using EFI is prefered over switching grub to GRUB_TERMINAL_OUTPUT=console. I would expect GRUB_TERMINAL_OUTPUT=console to also work but I'm not sure. I don't think that the classic BIOS boot stuff is still tested by laptop vendors and esp. not tested with non standard BIOS settings ...

Quoted 3 lines

The grub gfx mode is GRUB_TERMINAL_OUTPUT="console", fedora default in all cases here. Grub itself shows fine when the MUX mode is in dgpu mode (aka, internal display connected to dgpu).

Ah ok, so I misunderstood and the problem only happens *after* grub?

Quoted 8 lines

Have I understood that correctly?

And this is on Fedora with the nvidia binary driver ?

The problem then likely is that the nvidia binary driver is not in the initrd (which is by design since it may need to be rebuild on a driver update while the kernel is kept at the same version, so the initrd won't be rebuild).

That was indeed the issue. It also creates new problems for when a user wants to use iGPU only via the plain (and frankly not adequate or good) method of simply removing the dGPU from the device tree.

Currently I maintain the supergfxd tool which is a lot more advanced than the other gpu switchers around, and I expose both the above method, and also PCI hotplug, and the ASUS WMI method (which I now think is used by other vendors also). Hotplug and Asus method can force the device off, and it can't be brought back by a PCI rescan - but to do so safely the Nvidia drivers must be unused and unloaded. I guess I'll need to tweak the boot process of supergfxd and block things until this is done.

Maybe we can move this to a new topic, because there looks to be a few things to discuss in relation to hybrid laptops, and specifically Nvidia with MUX, and Advanced Optimus.

Cheers,
Luke.

#17 lore raw

Hi,

On 6/7/23 00:45, Luke Jones wrote:

<snip>

Quoted 6 lines
Quoted 3 lines

I must admit I've lost track a bit of the state of v2 during this discussion. Can I pick up v2 as is, or were there (other) remarks which need addressing and should I expect a v3 ?

There will be a V3. I don't anticipate any issues at all with this, and some folks have been using this patch with Gnome and KDE since V2 was submitted.

Ok.

Quoted 41 lines
Quoted 1 line

####### Switch to (off-topic) GPU mux discussion ########

**snip**

Quoted 18 lines
Quoted 12 lines
Quoted 11 lines

I think the best thing to do here is to just use EFI on machines like this. That or put grub in text mode so that it makes BIOS calls to display text. Using GRUB_TERMINAL_OUTPUT=gfxterm combined with classic BIOS booting will make grub try to directly drive the gfx card itself and I'm not surprised that it gets that wrong in this case.
Note I think that just using EFI is prefered over switching grub to GRUB_TERMINAL_OUTPUT=console. I would expect GRUB_TERMINAL_OUTPUT=console to also work but I'm not sure. I don't think that the classic BIOS boot stuff is still tested by laptop vendors and esp. not tested with non standard BIOS settings ...

Quoted 3 lines

The grub gfx mode is GRUB_TERMINAL_OUTPUT="console", fedora default in all cases here. Grub itself shows fine when the MUX mode is in dgpu mode (aka, internal display connected to dgpu).

Ah ok, so I misunderstood and the problem only happens *after* grub?

Quoted 8 lines

Have I understood that correctly?

And this is on Fedora with the nvidia binary driver ?

The problem then likely is that the nvidia binary driver is not in the initrd (which is by design since it may need to be rebuild on a driver update while the kernel is kept at the same version, so the initrd won't be rebuild).

That was indeed the issue. It also creates new problems for when a user wants to use iGPU only via the plain (and frankly not adequate or good) method of simply removing the dGPU from the device tree.

Currently I maintain the supergfxd tool which is a lot more advanced than the other gpu switchers around, and I expose both the above method, and also PCI hotplug, and the ASUS WMI method (which I now think is used by other vendors also). Hotplug and Asus method can force the device off, and it can't be brought back by a PCI rescan - but to do so safely the Nvidia drivers must be unused and unloaded. I guess I'll need to tweak the boot process of supergfxd and block things until this is done.

Quoted 3 lines

Maybe we can move this to a new topic, because there looks to be a few things to discuss in relation to hybrid laptops, and specifically Nvidia with MUX, and Advanced Optimus.

Yes if you want to discuss this further please start a new mailinglist thread for this and also please put the dri-devel list on the Cc:

[email protected]

Regards,

Hans