Skip to contentSkip to conversation

rockchip: A few clock cleanups for rk3288

PATCH Applied Douglas Anderson 3 participants 17 messages Apr 9, 2019 – Apr 12, 2019 1 message not in the archive

Subsystems (3)

v1 of 2 Applied Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover rockchip: A few clock cleanups for rk3288

This series contains a few misc clock cleanups for Rockchip rk3288 found by comparing to what's in the downstream Chrome OS 3.14 kernel.

NOTES:
* The PWM patches could go in separately from the revert but that would cause a merge conflict which is why they're together in a series.
* Having the PWM marked as a critical clock _definitely_ needs to land before switching the clock in the device tree.

Caesar Wang (1):
ARM: dts: rockchip: fix PWM clock found on RK3288 Socs

Douglas Anderson (2):
Revert "clk: rockchip: mark noc and some special clk as critical on

    rk3288"

clk: rockchip: Make rkpwm a critical clock on rk3288

 arch/arm/boot/dts/rk3288.dtsi     |  8 ++++----
 drivers/clk/rockchip/clk-rk3288.c | 17 ++++++-----------
 2 files changed, 10 insertions(+), 15 deletions(-)
Signature · 1 line
2.21.0.392.gf8f6787159e-goog
#1 lore raw

PATCH 1/3 Revert "clk: rockchip: mark noc and some special clk as critical on rk3288"

This reverts commit 55bb6a633c33caf68ab470907ecf945289cb733d.

The clocks that were enabled by that patch are pretty questionable. Specifically looking at what has been shipping on rk3288-veyron Chromebooks almost all of these clocks are safely turned off and cause no apparent problems. If some boards need these clocks turned on for some reason then it seems like we should figure out how to do that at a board level.

NOTE: turning these clocks off doesn't seem to do a whole lot in terms of power savings (checking the power on the logic rail). It appears to save maybe 1-2mW. ...but still it seems like we should turn the clocks off if they aren't needed.

Digging into the clocks here to describe why they shouldn't need to be left on:

atclk: No documentation about this clock other than that it goes to the CPU. CPU functions fine without it on.

jtag: Presumably this clock is only needed if you're debugging with JTAG. It doesn't seem like it makes sense to waste power for every rk3288 user. Perhaps this could be turned on with a CONFIG option?

pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two clocks on only during kernel panics in order to access some coresight registers. Since nothing in the upstream kernel does this we should be able to leave them off safely.

hsicphy12m_xin12m: There is no indication of why this clock would need to be turned on for boards that don't use HSIC.

pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn these 4 clocks on only when doing DDR transitions and they are off otherwise. I see no reason why they'd need to be on in the upstream kernel which doesn't support DDRFreq.

pmu_hclk_otg0: A "chip design defect" is mentioned in the original patch but no details. This clock has always been gated in shipping veyron Chromebooks so presumably this chip defect doesn't affect all boards.

---

 drivers/clk/rockchip/clk-rk3288.c | 14 ++++----------
 1 file changed, 4 insertions(+), 10 deletions(-)
drivers/clk/rockchip/clk-rk3288.c +4 -10
index 5a67b7869960..06287810474e 100644
@@ -313,13 +313,13 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
 	COMPOSITE_NOMUX(0, "aclk_core_mp", "armclk", CLK_IGNORE_UNUSED,
 			RK3288_CLKSEL_CON(0), 4, 4, DFLAGS | CLK_DIVIDER_READ_ONLY,
 			RK3288_CLKGATE_CON(12), 6, GFLAGS),
-	COMPOSITE_NOMUX(0, "atclk", "armclk", CLK_IGNORE_UNUSED,
+	COMPOSITE_NOMUX(0, "atclk", "armclk", 0,
 			RK3288_CLKSEL_CON(37), 4, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
 			RK3288_CLKGATE_CON(12), 7, GFLAGS),
 	COMPOSITE_NOMUX(0, "pclk_dbg_pre", "armclk", CLK_IGNORE_UNUSED,
 			RK3288_CLKSEL_CON(37), 9, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
 			RK3288_CLKGATE_CON(12), 8, GFLAGS),
-	GATE(0, "pclk_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
+	GATE(0, "pclk_dbg", "pclk_dbg_pre", 0,
 			RK3288_CLKGATE_CON(12), 9, GFLAGS),
 	GATE(0, "cs_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
 			RK3288_CLKGATE_CON(12), 10, GFLAGS),
@@ -647,7 +647,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
 	INVERTER(SCLK_HSADC, "sclk_hsadc", "sclk_hsadc_out",
 			RK3288_CLKSEL_CON(22), 7, IFLAGS),
 
-	GATE(0, "jtag", "ext_jtag", CLK_IGNORE_UNUSED,
+	GATE(0, "jtag", "ext_jtag", 0,
 			RK3288_CLKGATE_CON(4), 14, GFLAGS),
 
 	COMPOSITE_NODIV(SCLK_USBPHY480M_SRC, "usbphy480m_src", mux_usbphy480m_p, 0,
@@ -656,7 +656,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
 	COMPOSITE_NODIV(SCLK_HSICPHY480M, "sclk_hsicphy480m", mux_hsicphy480m_p, 0,
 			RK3288_CLKSEL_CON(29), 0, 2, MFLAGS,
 			RK3288_CLKGATE_CON(3), 6, GFLAGS),
-	GATE(0, "hsicphy12m_xin12m", "xin12m", CLK_IGNORE_UNUSED,
+	GATE(0, "hsicphy12m_xin12m", "xin12m", 0,
 			RK3288_CLKGATE_CON(13), 9, GFLAGS),
 	DIV(0, "hsicphy12m_usbphy", "sclk_hsicphy480m", 0,
 			RK3288_CLKSEL_CON(11), 8, 6, DFLAGS),
@@ -837,12 +837,6 @@ static const char *const rk3288_critical_clocks[] __initconst = {
 	"pclk_alive_niu",
 	"pclk_pd_pmu",
 	"pclk_pmu_niu",
-	"pclk_core_niu",
-	"pclk_ddrupctl0",
-	"pclk_publ0",
-	"pclk_ddrupctl1",
-	"pclk_publ1",
-	"pmu_hclk_otg0",
 };
 
 static void __iomem *rk3288_cru_base;
Signature · 1 line
2.21.0.392.gf8f6787159e-goog
#2 lore raw

Re: [PATCH 1/3] Revert "clk: rockchip: mark noc and some special clk as critical on rk3288"

hi,

Quoted 69 lines · Douglas Anderson

This reverts commit 55bb6a633c33caf68ab470907ecf945289cb733d.

The clocks that were enabled by that patch are pretty questionable. Specifically looking at what has been shipping on rk3288-veyron Chromebooks almost all of these clocks are safely turned off and cause no apparent problems. If some boards need these clocks turned on for some reason then it seems like we should figure out how to do that at a board level.

NOTE: turning these clocks off doesn't seem to do a whole lot in terms of power savings (checking the power on the logic rail). It appears to save maybe 1-2mW. ...but still it seems like we should turn the clocks off if they aren't needed.

Digging into the clocks here to describe why they shouldn't need to be left on:

atclk: No documentation about this clock other than that it goes to the CPU. CPU functions fine without it on.

jtag: Presumably this clock is only needed if you're debugging with JTAG. It doesn't seem like it makes sense to waste power for every rk3288 user. Perhaps this could be turned on with a CONFIG option?

pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two clocks on only during kernel panics in order to access some coresight registers. Since nothing in the upstream kernel does this we should be able to leave them off safely.

hsicphy12m_xin12m: There is no indication of why this clock would need to be turned on for boards that don't use HSIC.

pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn these 4 clocks on only when doing DDR transitions and they are off otherwise. I see no reason why they'd need to be on in the upstream kernel which doesn't support DDRFreq.

pmu_hclk_otg0: A "chip design defect" is mentioned in the original patch but no details. This clock has always been gated in shipping veyron Chromebooks so presumably this chip defect doesn't affect all boards.

---

  drivers/clk/rockchip/clk-rk3288.c | 14 ++++----------
  1 file changed, 4 insertions(+), 10 deletions(-)
drivers/clk/rockchip/clk-rk3288.c +2 -2
index 5a67b7869960..06287810474e 100644
@@ -313,13 +313,13 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
  	COMPOSITE_NOMUX(0, "aclk_core_mp", "armclk", CLK_IGNORE_UNUSED,
  			RK3288_CLKSEL_CON(0), 4, 4, DFLAGS | CLK_DIVIDER_READ_ONLY,
  			RK3288_CLKGATE_CON(12), 6, GFLAGS),
-	COMPOSITE_NOMUX(0, "atclk", "armclk", CLK_IGNORE_UNUSED,
+	COMPOSITE_NOMUX(0, "atclk", "armclk", 0,
  			RK3288_CLKSEL_CON(37), 4, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
  			RK3288_CLKGATE_CON(12), 7, GFLAGS),
  	COMPOSITE_NOMUX(0, "pclk_dbg_pre", "armclk", CLK_IGNORE_UNUSED,
  			RK3288_CLKSEL_CON(37), 9, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
  			RK3288_CLKGATE_CON(12), 8, GFLAGS),
-	GATE(0, "pclk_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
+	GATE(0, "pclk_dbg", "pclk_dbg_pre", 0,
  			RK3288_CLKGATE_CON(12), 9, GFLAGS),
  	GATE(0, "cs_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
  			RK3288_CLKGATE_CON(12), 10, GFLAGS),

drivers/clk/rockchip/clk-rk3288.c static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = { · line 651

Quoted 6 lines
drivers/clk/rockchip/clk-rk3288.c +1 -1
@@ -647,7 +647,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
  	INVERTER(SCLK_HSADC, "sclk_hsadc", "sclk_hsadc_out",
  			RK3288_CLKSEL_CON(22), 7, IFLAGS),
 
-	GATE(0, "jtag", "ext_jtag", CLK_IGNORE_UNUSED,
+	GATE(0, "jtag", "ext_jtag", 0,
  			RK3288_CLKGATE_CON(4), 14, GFLAGS),

CLK_IGNORE_UNUSED:
Whether to close the unused clk after clk init complete. not affect there own enable/disable.
JTAG is not have device node, when need jtag to debug, may be the system is crashed, there is no way to turn on this clk.

Quoted 12 lines
drivers/clk/rockchip/clk-rk3288.c +1 -1
  	COMPOSITE_NODIV(SCLK_USBPHY480M_SRC, "usbphy480m_src", mux_usbphy480m_p, 0,
@@ -656,7 +656,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
  	COMPOSITE_NODIV(SCLK_HSICPHY480M, "sclk_hsicphy480m", mux_hsicphy480m_p, 0,
  			RK3288_CLKSEL_CON(29), 0, 2, MFLAGS,
  			RK3288_CLKGATE_CON(3), 6, GFLAGS),
-	GATE(0, "hsicphy12m_xin12m", "xin12m", CLK_IGNORE_UNUSED,
+	GATE(0, "hsicphy12m_xin12m", "xin12m", 0,
  			RK3288_CLKGATE_CON(13), 9, GFLAGS),
  	DIV(0, "hsicphy12m_usbphy", "sclk_hsicphy480m", 0,
  			RK3288_CLKSEL_CON(11), 8, 6, DFLAGS),

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 844

Quoted 8 lines
drivers/clk/rockchip/clk-rk3288.c +0 -5
@@ -837,12 +837,6 @@ static const char *const rk3288_critical_clocks[] __initconst = {
  	"pclk_alive_niu",
  	"pclk_pd_pmu",
  	"pclk_pmu_niu",
-	"pclk_core_niu",
-	"pclk_ddrupctl0",
-	"pclk_publ0",
-	"pclk_ddrupctl1",
-	"pclk_publ1",

These clks needed enable, device node not use this clk, so we mark it as critical.

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 845

Quoted 1 line
drivers/clk/rockchip/clk-rk3288.c +0 -1
-	"pmu_hclk_otg0",

It's a soc bug, pmu_hclk_otg0 must always on.

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 842

Quoted 3 lines
drivers/clk/rockchip/clk-rk3288.c +0 -0
  };
 
  static void __iomem *rk3288_cru_base;

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#3 lore raw

Re: [PATCH 1/3] Revert "clk: rockchip: mark noc and some special clk as critical on rk3288"

Hi,

Quoted 76 lines · elaine.zhang

hi,

Quoted 72 lines · Douglas Anderson

This reverts commit 55bb6a633c33caf68ab470907ecf945289cb733d.

The clocks that were enabled by that patch are pretty questionable. Specifically looking at what has been shipping on rk3288-veyron Chromebooks almost all of these clocks are safely turned off and cause no apparent problems. If some boards need these clocks turned on for some reason then it seems like we should figure out how to do that at a board level.

NOTE: turning these clocks off doesn't seem to do a whole lot in terms of power savings (checking the power on the logic rail). It appears to save maybe 1-2mW. ...but still it seems like we should turn the clocks off if they aren't needed.

Digging into the clocks here to describe why they shouldn't need to be left on:

atclk: No documentation about this clock other than that it goes to the CPU. CPU functions fine without it on.

jtag: Presumably this clock is only needed if you're debugging with JTAG. It doesn't seem like it makes sense to waste power for every rk3288 user. Perhaps this could be turned on with a CONFIG option?

pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two clocks on only during kernel panics in order to access some coresight registers. Since nothing in the upstream kernel does this we should be able to leave them off safely.

hsicphy12m_xin12m: There is no indication of why this clock would need to be turned on for boards that don't use HSIC.

pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn these 4 clocks on only when doing DDR transitions and they are off otherwise. I see no reason why they'd need to be on in the upstream kernel which doesn't support DDRFreq.

pmu_hclk_otg0: A "chip design defect" is mentioned in the original patch but no details. This clock has always been gated in shipping veyron Chromebooks so presumably this chip defect doesn't affect all boards.

---

  drivers/clk/rockchip/clk-rk3288.c | 14 ++++----------
  1 file changed, 4 insertions(+), 10 deletions(-)
drivers/clk/rockchip/clk-rk3288.c +2 -2
index 5a67b7869960..06287810474e 100644
@@ -313,13 +313,13 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      COMPOSITE_NOMUX(0, "aclk_core_mp", "armclk", CLK_IGNORE_UNUSED,
                      RK3288_CLKSEL_CON(0), 4, 4, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 6, GFLAGS),
-     COMPOSITE_NOMUX(0, "atclk", "armclk", CLK_IGNORE_UNUSED,
+     COMPOSITE_NOMUX(0, "atclk", "armclk", 0,
                      RK3288_CLKSEL_CON(37), 4, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 7, GFLAGS),
      COMPOSITE_NOMUX(0, "pclk_dbg_pre", "armclk", CLK_IGNORE_UNUSED,
                      RK3288_CLKSEL_CON(37), 9, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 8, GFLAGS),
-     GATE(0, "pclk_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
+     GATE(0, "pclk_dbg", "pclk_dbg_pre", 0,
                      RK3288_CLKGATE_CON(12), 9, GFLAGS),
      GATE(0, "cs_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
                      RK3288_CLKGATE_CON(12), 10, GFLAGS),
@@ -647,7 +647,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      INVERTER(SCLK_HSADC, "sclk_hsadc", "sclk_hsadc_out",
                      RK3288_CLKSEL_CON(22), 7, IFLAGS),
 
Quoted 8 lines

drivers/clk/rockchip/clk-rk3288.c static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = { · line 651

Quoted 3 lines
drivers/clk/rockchip/clk-rk3288.c +1 -1
-     GATE(0, "jtag", "ext_jtag", CLK_IGNORE_UNUSED,
+     GATE(0, "jtag", "ext_jtag", 0,
                      RK3288_CLKGATE_CON(4), 14, GFLAGS),

CLK_IGNORE_UNUSED:
Whether to close the unused clk after clk init complete. not affect there own enable/disable.
JTAG is not have device node, when need jtag to debug, may be the system is crashed, there is no way to turn on this clk.

As I mentioned in the commit message this seems like the kind of thing that should be controlled by a CONFIG_ option. It's a debug option that's fine to have on all the time but consumes resources so some people might want to turn it off.

Quoted 13 lines
Quoted 13 lines
drivers/clk/rockchip/clk-rk3288.c +1 -1
      COMPOSITE_NODIV(SCLK_USBPHY480M_SRC, "usbphy480m_src", mux_usbphy480m_p, 0,
@@ -656,7 +656,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      COMPOSITE_NODIV(SCLK_HSICPHY480M, "sclk_hsicphy480m", mux_hsicphy480m_p, 0,
                      RK3288_CLKSEL_CON(29), 0, 2, MFLAGS,
                      RK3288_CLKGATE_CON(3), 6, GFLAGS),
-     GATE(0, "hsicphy12m_xin12m", "xin12m", CLK_IGNORE_UNUSED,
+     GATE(0, "hsicphy12m_xin12m", "xin12m", 0,
                      RK3288_CLKGATE_CON(13), 9, GFLAGS),
      DIV(0, "hsicphy12m_usbphy", "sclk_hsicphy480m", 0,
                      RK3288_CLKSEL_CON(11), 8, 6, DFLAGS),
@@ -837,12 +837,6 @@ static const char *const rk3288_critical_clocks[] __initconst = {
      "pclk_alive_niu",
      "pclk_pd_pmu",
Quoted 8 lines

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 844

Quoted 6 lines
drivers/clk/rockchip/clk-rk3288.c +0 -5
      "pclk_pmu_niu",
-     "pclk_core_niu",
-     "pclk_ddrupctl0",
-     "pclk_publ0",
-     "pclk_ddrupctl1",
-     "pclk_publ1",

These clks needed enable, device node not use this clk, so we mark it as critical.

What breaks if you don't enable these clocks? As far as I can tell these clocks only need to be enabled while touching memory controller registers (deep suspend/resume and DDRFreq transitions). On Chromebooks everything works fine with these clocks only turned on when needed.

Quoted 2 lines

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 845

Quoted 1 line
drivers/clk/rockchip/clk-rk3288.c +0 -1
-     "pmu_hclk_otg0",

It's a soc bug, pmu_hclk_otg0 must always on.

So you said in your previous commit message. However we've shipped lots and lots of Chromebooks with this clock off. Can you explain what is broken? Is this only needed for gadget mode (which we don't use), for instance?

-Doug

A message that is not in the archive (sent off-list or not yet received): [email protected]

#5 lore raw

Re: [PATCH 1/3] Revert "clk: rockchip: mark noc and some special clk as critical on rk3288"

Hi,

Quoted 95 lines · elaine.zhang

hi,

在 2019/4/10 下午11:34, Doug Anderson 写道:

Hi,

On Tue, Apr 9, 2019 at 11:23 PM elaine.zhang <[email protected]> wrote:

hi,

在 2019/4/10 上午4:47, Douglas Anderson 写道:

This reverts commit 55bb6a633c33caf68ab470907ecf945289cb733d.

The clocks that were enabled by that patch are pretty questionable. Specifically looking at what has been shipping on rk3288-veyron Chromebooks almost all of these clocks are safely turned off and cause no apparent problems. If some boards need these clocks turned on for some reason then it seems like we should figure out how to do that at a board level.

NOTE: turning these clocks off doesn't seem to do a whole lot in terms of power savings (checking the power on the logic rail). It appears to save maybe 1-2mW. ...but still it seems like we should turn the clocks off if they aren't needed.

Digging into the clocks here to describe why they shouldn't need to be left on:

atclk: No documentation about this clock other than that it goes to the CPU. CPU functions fine without it on.

jtag: Presumably this clock is only needed if you're debugging with JTAG. It doesn't seem like it makes sense to waste power for every rk3288 user. Perhaps this could be turned on with a CONFIG option?

pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two clocks on only during kernel panics in order to access some coresight registers. Since nothing in the upstream kernel does this we should be able to leave them off safely.

hsicphy12m_xin12m: There is no indication of why this clock would need to be turned on for boards that don't use HSIC.

pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn these 4 clocks on only when doing DDR transitions and they are off otherwise. I see no reason why they'd need to be on in the upstream kernel which doesn't support DDRFreq.

pmu_hclk_otg0: A "chip design defect" is mentioned in the original patch but no details. This clock has always been gated in shipping veyron Chromebooks so presumably this chip defect doesn't affect all boards.

---

  drivers/clk/rockchip/clk-rk3288.c | 14 ++++----------
  1 file changed, 4 insertions(+), 10 deletions(-)
drivers/clk/rockchip/clk-rk3288.c +3 -3
index 5a67b7869960..06287810474e 100644
@@ -313,13 +313,13 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      COMPOSITE_NOMUX(0, "aclk_core_mp", "armclk", CLK_IGNORE_UNUSED,
                      RK3288_CLKSEL_CON(0), 4, 4, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 6, GFLAGS),
-     COMPOSITE_NOMUX(0, "atclk", "armclk", CLK_IGNORE_UNUSED,
+     COMPOSITE_NOMUX(0, "atclk", "armclk", 0,
                      RK3288_CLKSEL_CON(37), 4, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 7, GFLAGS),
      COMPOSITE_NOMUX(0, "pclk_dbg_pre", "armclk", CLK_IGNORE_UNUSED,
                      RK3288_CLKSEL_CON(37), 9, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 8, GFLAGS),
-     GATE(0, "pclk_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
+     GATE(0, "pclk_dbg", "pclk_dbg_pre", 0,
                      RK3288_CLKGATE_CON(12), 9, GFLAGS),
      GATE(0, "cs_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
                      RK3288_CLKGATE_CON(12), 10, GFLAGS),
@@ -647,7 +647,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      INVERTER(SCLK_HSADC, "sclk_hsadc", "sclk_hsadc_out",
                      RK3288_CLKSEL_CON(22), 7, IFLAGS),
 
-     GATE(0, "jtag", "ext_jtag", CLK_IGNORE_UNUSED,
+     GATE(0, "jtag", "ext_jtag", 0,
                      RK3288_CLKGATE_CON(4), 14, GFLAGS),
 

CLK_IGNORE_UNUSED:
Whether to close the unused clk after clk init complete. not affect there own enable/disable.
JTAG is not have device node, when need jtag to debug, may be the system is crashed, there is no way to turn on this clk.

Quoted 8 lines

As I mentioned in the commit message this seems like the kind of thing that should be controlled by a CONFIG_ option. It's a debug option that's fine to have on all the time but consumes resources so some people might want to turn it off.

Currently, CONFIG_ option is not implemented. We will refer to this suggestion.

For debug, I don't hope to remove the flag CLK_IGNORE_UNUSED.(The clk static power is very small)

I'll leave it up to Heiko for what to do here. I agree that it's not tons of power (this whole patch saved 1-2 mW on the INT rail) but I'd still prefer for clocks to be off if they can. In general one could also argue that keeping JTAG off by default could be good for security.

...but I guess I have to wonder how you're doing JTAG on upstream kernels without any extra patches anyway. Automatic JTAG switching is turned off in "drivers/soc/rockchip/grf.c". ...and by default the JTAG signals are muxed as the SD Card. So presumably you've already got extra patches in order to make JTAG work.

I assume that the clocks that are important for JTAG are "atclk", "jtag", "pclk_dbg", and "pclk_core_niu".

Quoted 23 lines
      COMPOSITE_NODIV(SCLK_USBPHY480M_SRC, "usbphy480m_src", mux_usbphy480m_p, 0,
drivers/clk/rockchip/clk-rk3288.c +1 -6
@@ -656,7 +656,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      COMPOSITE_NODIV(SCLK_HSICPHY480M, "sclk_hsicphy480m", mux_hsicphy480m_p, 0,
                      RK3288_CLKSEL_CON(29), 0, 2, MFLAGS,
                      RK3288_CLKGATE_CON(3), 6, GFLAGS),
-     GATE(0, "hsicphy12m_xin12m", "xin12m", CLK_IGNORE_UNUSED,
+     GATE(0, "hsicphy12m_xin12m", "xin12m", 0,
                      RK3288_CLKGATE_CON(13), 9, GFLAGS),
      DIV(0, "hsicphy12m_usbphy", "sclk_hsicphy480m", 0,
                      RK3288_CLKSEL_CON(11), 8, 6, DFLAGS),
@@ -837,12 +837,6 @@ static const char *const rk3288_critical_clocks[] __initconst = {
      "pclk_alive_niu",
      "pclk_pd_pmu",
      "pclk_pmu_niu",
-     "pclk_core_niu",
-     "pclk_ddrupctl0",
-     "pclk_publ0",
-     "pclk_ddrupctl1",
-     "pclk_publ1",
 

These clks needed enable, device node not use this clk, so we mark it as critical.

Quoted 7 lines

What breaks if you don't enable these clocks? As far as I can tell these clocks only need to be enabled while touching memory controller registers (deep suspend/resume and DDRFreq transitions). On Chromebooks everything works fine with these clocks only turned on when needed.

If need to enable these clks, ddrupctl0/ddrupctl1/publ0/publ1 clks no driver to handle them, so mark these clk as critical.

Perhaps it's just a typo, but you say "If need to enable". I see no evidence that these clocks need to be enabled unless there is code touching memory controller registers. Thus we don't need to enable them so they don't need to be critical.

Quoted 15 lines

- "pmu_hclk_otg0",

It's a soc bug, pmu_hclk_otg0 must always on.

So you said in your previous commit message. However we've shipped lots and lots of Chromebooks with this clock off. Can you explain what is broken? Is this only needed for gadget mode (which we don't use), for instance?

test case:

recovery test, < 1 hour , system crash.

log:

Quoted 9 lines
[  127.569629] I[0:      swapper/0:    0] GOTGCTL        @0xFFFFFF8000B80000 : 0x00400010
[  127.569644] I[0:      swapper/0:    0] GOTGINT        @0xFFFFFF8000B80004 : 0x00400010
[  127.569659] I[0:      swapper/0:    0] GAHBCFG        @0xFFFFFF8000B80008 : 0x00400010
[  127.569673] I[0:      swapper/0:    0] GUSBCFG        @0xFFFFFF8000B8000C : 0x00400010
[  127.569688] I[0:      swapper/0:    0] GRSTCTL        @0xFFFFFF8000B80010 : 0x00400010
[  127.569702] I[0:      swapper/0:    0] GINTSTS        @0xFFFFFF8000B80014 : 0x00400010
[  127.569718] I[0:      swapper/0:    0] GINTMSK        @0xFFFFFF8000B80018 : 0x00400010
[  127.569733] I[0:      swapper/0:    0] GRXSTSR        @0xFFFFFF8000B8001C : 0x00400010
[  127.569748] I[0:      swapper/0:    0] GRXFSIZ        @0xFFFFFF8000B80024 : 0x00400010

I don't know what a "recovery test" is and I don't understand your logs.

Can you explain we do not run into this on Chromebooks?

Quoted 3 lines

reason:

USB OTG controller supports turning off most logic power, and then only one PMU module is left. This clock cannot be turned off, which is similar to the always on module in USB OTG.

Can't you just add a patch to the dwc2 driver to have it grab this clock? I assume this clock doesn't need to be turned on unless you're using the OTG contoller in a certain way?

NOTE: nowhere in your responses did you talk about why "hsicphy12m_xin12m" needed to be marked as IGNORE_UNUSED. I guess you're OK with removing that?

-Doug

maintainer
#6 lore raw

Re: [PATCH 1/3] Revert "clk: rockchip: mark noc and some special clk as critical on rk3288"

Hi,

Am Donnerstag, 11. April 2019, 17:26:41 CEST schrieb Doug Anderson:

Quoted 102 lines · elaine.zhang
Quoted 86 lines · Doug Anderson

On Tue, Apr 9, 2019 at 11:23 PM elaine.zhang <[email protected]> wrote:
在 2019/4/10 上午4:47, Douglas Anderson 写道:

This reverts commit 55bb6a633c33caf68ab470907ecf945289cb733d.

The clocks that were enabled by that patch are pretty questionable. Specifically looking at what has been shipping on rk3288-veyron Chromebooks almost all of these clocks are safely turned off and cause no apparent problems. If some boards need these clocks turned on for some reason then it seems like we should figure out how to do that at a board level.

NOTE: turning these clocks off doesn't seem to do a whole lot in terms of power savings (checking the power on the logic rail). It appears to save maybe 1-2mW. ...but still it seems like we should turn the clocks off if they aren't needed.

Digging into the clocks here to describe why they shouldn't need to be left on:

atclk: No documentation about this clock other than that it goes to the CPU. CPU functions fine without it on.

jtag: Presumably this clock is only needed if you're debugging with JTAG. It doesn't seem like it makes sense to waste power for every rk3288 user. Perhaps this could be turned on with a CONFIG option?

pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two clocks on only during kernel panics in order to access some coresight registers. Since nothing in the upstream kernel does this we should be able to leave them off safely.

hsicphy12m_xin12m: There is no indication of why this clock would need to be turned on for boards that don't use HSIC.

pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn these 4 clocks on only when doing DDR transitions and they are off otherwise. I see no reason why they'd need to be on in the upstream kernel which doesn't support DDRFreq.

pmu_hclk_otg0: A "chip design defect" is mentioned in the original patch but no details. This clock has always been gated in shipping veyron Chromebooks so presumably this chip defect doesn't affect all boards.

---

  drivers/clk/rockchip/clk-rk3288.c | 14 ++++----------
  1 file changed, 4 insertions(+), 10 deletions(-)
drivers/clk/rockchip/clk-rk3288.c +3 -3
index 5a67b7869960..06287810474e 100644
@@ -313,13 +313,13 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      COMPOSITE_NOMUX(0, "aclk_core_mp", "armclk", CLK_IGNORE_UNUSED,
                      RK3288_CLKSEL_CON(0), 4, 4, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 6, GFLAGS),
-     COMPOSITE_NOMUX(0, "atclk", "armclk", CLK_IGNORE_UNUSED,
+     COMPOSITE_NOMUX(0, "atclk", "armclk", 0,
                      RK3288_CLKSEL_CON(37), 4, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 7, GFLAGS),
      COMPOSITE_NOMUX(0, "pclk_dbg_pre", "armclk", CLK_IGNORE_UNUSED,
                      RK3288_CLKSEL_CON(37), 9, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
                      RK3288_CLKGATE_CON(12), 8, GFLAGS),
-     GATE(0, "pclk_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
+     GATE(0, "pclk_dbg", "pclk_dbg_pre", 0,
                      RK3288_CLKGATE_CON(12), 9, GFLAGS),
      GATE(0, "cs_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
                      RK3288_CLKGATE_CON(12), 10, GFLAGS),
@@ -647,7 +647,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      INVERTER(SCLK_HSADC, "sclk_hsadc", "sclk_hsadc_out",
                      RK3288_CLKSEL_CON(22), 7, IFLAGS),
 
-     GATE(0, "jtag", "ext_jtag", CLK_IGNORE_UNUSED,
+     GATE(0, "jtag", "ext_jtag", 0,
                      RK3288_CLKGATE_CON(4), 14, GFLAGS),
 

CLK_IGNORE_UNUSED:
Whether to close the unused clk after clk init complete. not affect there own enable/disable.
JTAG is not have device node, when need jtag to debug, may be the system is crashed, there is no way to turn on this clk.

Quoted 8 lines

As I mentioned in the commit message this seems like the kind of thing that should be controlled by a CONFIG_ option. It's a debug option that's fine to have on all the time but consumes resources so some people might want to turn it off.

Currently, CONFIG_ option is not implemented. We will refer to this suggestion.

For debug, I don't hope to remove the flag CLK_IGNORE_UNUSED.(The clk static power is very small)

I'll leave it up to Heiko for what to do here. I agree that it's not tons of power (this whole patch saved 1-2 mW on the INT rail) but I'd still prefer for clocks to be off if they can. In general one could also argue that keeping JTAG off by default could be good for security.

Quoted 8 lines

...but I guess I have to wonder how you're doing JTAG on upstream kernels without any extra patches anyway. Automatic JTAG switching is turned off in "drivers/soc/rockchip/grf.c". ...and by default the JTAG signals are muxed as the SD Card. So presumably you've already got extra patches in order to make JTAG work.

I assume that the clocks that are important for JTAG are "atclk", "jtag", "pclk_dbg", and "pclk_core_niu".

Isn't JTAG part of the coresight package anyway? The whole coresight stuff, so in an upstream-context I'd somehow expect it to get activated through that. Or is it actually separate and only in the debug-diagram in the TRM mixed into coresight?

In any case I'm with Doug here, for jtag you need to modify your kernel anyway for pinctrl settings, so could also enable the clock in that case.

Quoted 29 lines
Quoted 29 lines
      COMPOSITE_NODIV(SCLK_USBPHY480M_SRC, "usbphy480m_src", mux_usbphy480m_p, 0,
drivers/clk/rockchip/clk-rk3288.c +1 -6
@@ -656,7 +656,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      COMPOSITE_NODIV(SCLK_HSICPHY480M, "sclk_hsicphy480m", mux_hsicphy480m_p, 0,
                      RK3288_CLKSEL_CON(29), 0, 2, MFLAGS,
                      RK3288_CLKGATE_CON(3), 6, GFLAGS),
-     GATE(0, "hsicphy12m_xin12m", "xin12m", CLK_IGNORE_UNUSED,
+     GATE(0, "hsicphy12m_xin12m", "xin12m", 0,
                      RK3288_CLKGATE_CON(13), 9, GFLAGS),
      DIV(0, "hsicphy12m_usbphy", "sclk_hsicphy480m", 0,
                      RK3288_CLKSEL_CON(11), 8, 6, DFLAGS),
@@ -837,12 +837,6 @@ static const char *const rk3288_critical_clocks[] __initconst = {
      "pclk_alive_niu",
      "pclk_pd_pmu",
      "pclk_pmu_niu",
-     "pclk_core_niu",
-     "pclk_ddrupctl0",
-     "pclk_publ0",
-     "pclk_ddrupctl1",
-     "pclk_publ1",
 

These clks needed enable, device node not use this clk, so we mark it as critical.

What breaks if you don't enable these clocks? As far as I can tell these clocks only need to be enabled while touching memory controller registers (deep suspend/resume and DDRFreq transitions). On Chromebooks everything works fine with these clocks only turned on when needed.

Quoted 6 lines
Quoted 1 line

If need to enable these clks, ddrupctl0/ddrupctl1/publ0/publ1 clks no driver to handle them, so mark these clk as critical.

Perhaps it's just a typo, but you say "If need to enable". I see no evidence that these clocks need to be enabled unless there is code touching memory controller registers. Thus we don't need to enable them so they don't need to be critical.

yep ... maybe Elaine can clarify in what other activities these clocks are needed ... I guess any ddr-scaling code would activate them before touching memory-controller-registers.

Quoted 30 lines
Quoted 15 lines

- "pmu_hclk_otg0",

It's a soc bug, pmu_hclk_otg0 must always on.

So you said in your previous commit message. However we've shipped lots and lots of Chromebooks with this clock off. Can you explain what is broken? Is this only needed for gadget mode (which we don't use), for instance?

test case:

recovery test, < 1 hour , system crash.

log:

Quoted 9 lines
[  127.569629] I[0:      swapper/0:    0] GOTGCTL        @0xFFFFFF8000B80000 : 0x00400010
[  127.569644] I[0:      swapper/0:    0] GOTGINT        @0xFFFFFF8000B80004 : 0x00400010
[  127.569659] I[0:      swapper/0:    0] GAHBCFG        @0xFFFFFF8000B80008 : 0x00400010
[  127.569673] I[0:      swapper/0:    0] GUSBCFG        @0xFFFFFF8000B8000C : 0x00400010
[  127.569688] I[0:      swapper/0:    0] GRSTCTL        @0xFFFFFF8000B80010 : 0x00400010
[  127.569702] I[0:      swapper/0:    0] GINTSTS        @0xFFFFFF8000B80014 : 0x00400010
[  127.569718] I[0:      swapper/0:    0] GINTMSK        @0xFFFFFF8000B80018 : 0x00400010
[  127.569733] I[0:      swapper/0:    0] GRXSTSR        @0xFFFFFF8000B8001C : 0x00400010
[  127.569748] I[0:      swapper/0:    0] GRXFSIZ        @0xFFFFFF8000B80024 : 0x00400010

I don't know what a "recovery test" is and I don't understand your logs.

Can you explain we do not run into this on Chromebooks?

Quoted 7 lines
Quoted 3 lines

reason:

USB OTG controller supports turning off most logic power, and then only one PMU module is left. This clock cannot be turned off, which is similar to the always on module in USB OTG.

Can't you just add a patch to the dwc2 driver to have it grab this clock? I assume this clock doesn't need to be turned on unless you're using the OTG contoller in a certain way?

So far we don't really know where the clock in question is sitting in the clock hirarchy. For example the kernel got a new interconnect framework recently, so handling non-device clocks in a device may haunt us later on.

@Elaine: could you elaborate what pmu_hclk_otg0 actually is for please?

Quoted 3 lines

NOTE: nowhere in your responses did you talk about why "hsicphy12m_xin12m" needed to be marked as IGNORE_UNUSED. I guess you're OK with removing that?

Thanks
Heiko

#7 lore raw

Re: [PATCH 1/3] Revert "clk: rockchip: mark noc and some special clk as critical on rk3288"

hi,

Quoted 112 lines · Heiko Stübner

Hi,

Am Donnerstag, 11. April 2019, 17:26:41 CEST schrieb Doug Anderson:

Quoted 101 lines · elaine.zhang
Quoted 86 lines · Doug Anderson

On Tue, Apr 9, 2019 at 11:23 PM elaine.zhang <[email protected]> wrote:
在 2019/4/10 上午4:47, Douglas Anderson 写道:

This reverts commit 55bb6a633c33caf68ab470907ecf945289cb733d.

The clocks that were enabled by that patch are pretty questionable. Specifically looking at what has been shipping on rk3288-veyron Chromebooks almost all of these clocks are safely turned off and cause no apparent problems. If some boards need these clocks turned on for some reason then it seems like we should figure out how to do that at a board level.

NOTE: turning these clocks off doesn't seem to do a whole lot in terms of power savings (checking the power on the logic rail). It appears to save maybe 1-2mW. ...but still it seems like we should turn the clocks off if they aren't needed.

Digging into the clocks here to describe why they shouldn't need to be left on:

atclk: No documentation about this clock other than that it goes to the CPU. CPU functions fine without it on.

jtag: Presumably this clock is only needed if you're debugging with JTAG. It doesn't seem like it makes sense to waste power for every rk3288 user. Perhaps this could be turned on with a CONFIG option?

pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two clocks on only during kernel panics in order to access some coresight registers. Since nothing in the upstream kernel does this we should be able to leave them off safely.

hsicphy12m_xin12m: There is no indication of why this clock would need to be turned on for boards that don't use HSIC.

pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn these 4 clocks on only when doing DDR transitions and they are off otherwise. I see no reason why they'd need to be on in the upstream kernel which doesn't support DDRFreq.

pmu_hclk_otg0: A "chip design defect" is mentioned in the original patch but no details. This clock has always been gated in shipping veyron Chromebooks so presumably this chip defect doesn't affect all boards.

---

   drivers/clk/rockchip/clk-rk3288.c | 14 ++++----------
   1 file changed, 4 insertions(+), 10 deletions(-)
drivers/clk/rockchip/clk-rk3288.c +3 -3
index 5a67b7869960..06287810474e 100644
@@ -313,13 +313,13 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
       COMPOSITE_NOMUX(0, "aclk_core_mp", "armclk", CLK_IGNORE_UNUSED,
                       RK3288_CLKSEL_CON(0), 4, 4, DFLAGS | CLK_DIVIDER_READ_ONLY,
                       RK3288_CLKGATE_CON(12), 6, GFLAGS),
-     COMPOSITE_NOMUX(0, "atclk", "armclk", CLK_IGNORE_UNUSED,
+     COMPOSITE_NOMUX(0, "atclk", "armclk", 0,
                       RK3288_CLKSEL_CON(37), 4, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
                       RK3288_CLKGATE_CON(12), 7, GFLAGS),
       COMPOSITE_NOMUX(0, "pclk_dbg_pre", "armclk", CLK_IGNORE_UNUSED,
                       RK3288_CLKSEL_CON(37), 9, 5, DFLAGS | CLK_DIVIDER_READ_ONLY,
                       RK3288_CLKGATE_CON(12), 8, GFLAGS),
-     GATE(0, "pclk_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
+     GATE(0, "pclk_dbg", "pclk_dbg_pre", 0,
                       RK3288_CLKGATE_CON(12), 9, GFLAGS),
       GATE(0, "cs_dbg", "pclk_dbg_pre", CLK_IGNORE_UNUSED,
                       RK3288_CLKGATE_CON(12), 10, GFLAGS),
@@ -647,7 +647,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
       INVERTER(SCLK_HSADC, "sclk_hsadc", "sclk_hsadc_out",
                       RK3288_CLKSEL_CON(22), 7, IFLAGS),
 
-     GATE(0, "jtag", "ext_jtag", CLK_IGNORE_UNUSED,
+     GATE(0, "jtag", "ext_jtag", 0,
                       RK3288_CLKGATE_CON(4), 14, GFLAGS),
 

CLK_IGNORE_UNUSED:
Whether to close the unused clk after clk init complete. not affect there own enable/disable.
JTAG is not have device node, when need jtag to debug, may be the system is crashed, there is no way to turn on this clk.

Quoted 8 lines

As I mentioned in the commit message this seems like the kind of thing that should be controlled by a CONFIG_ option. It's a debug option that's fine to have on all the time but consumes resources so some people might want to turn it off.

Currently, CONFIG_ option is not implemented. We will refer to this suggestion.

For debug, I don't hope to remove the flag CLK_IGNORE_UNUSED.(The clk static power is very small)

I'll leave it up to Heiko for what to do here. I agree that it's not tons of power (this whole patch saved 1-2 mW on the INT rail) but I'd still prefer for clocks to be off if they can. In general one could also argue that keeping JTAG off by default could be good for security.

Quoted 8 lines

...but I guess I have to wonder how you're doing JTAG on upstream kernels without any extra patches anyway. Automatic JTAG switching is turned off in "drivers/soc/rockchip/grf.c". ...and by default the JTAG signals are muxed as the SD Card. So presumably you've already got extra patches in order to make JTAG work.

I assume that the clocks that are important for JTAG are "atclk", "jtag", "pclk_dbg", and "pclk_core_niu".

Quoted 7 lines

Isn't JTAG part of the coresight package anyway? The whole coresight stuff, so in an upstream-context I'd somehow expect it to get activated through that. Or is it actually separate and only in the debug-diagram in the TRM mixed into coresight?

In any case I'm with Doug here, for jtag you need to modify your kernel anyway for pinctrl settings, so could also enable the clock in that case.

OK,  I agree.

Quoted 31 lines
Quoted 31 lines
Quoted 31 lines

       COMPOSITE_NODIV(SCLK_USBPHY480M_SRC, "usbphy480m_src", mux_usbphy480m_p, 0,
drivers/clk/rockchip/clk-rk3288.c +1 -6
@@ -656,7 +656,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
       COMPOSITE_NODIV(SCLK_HSICPHY480M, "sclk_hsicphy480m", mux_hsicphy480m_p, 0,
                       RK3288_CLKSEL_CON(29), 0, 2, MFLAGS,
                       RK3288_CLKGATE_CON(3), 6, GFLAGS),
-     GATE(0, "hsicphy12m_xin12m", "xin12m", CLK_IGNORE_UNUSED,
+     GATE(0, "hsicphy12m_xin12m", "xin12m", 0,
                       RK3288_CLKGATE_CON(13), 9, GFLAGS),
       DIV(0, "hsicphy12m_usbphy", "sclk_hsicphy480m", 0,
                       RK3288_CLKSEL_CON(11), 8, 6, DFLAGS),
@@ -837,12 +837,6 @@ static const char *const rk3288_critical_clocks[] __initconst = {
       "pclk_alive_niu",
       "pclk_pd_pmu",
       "pclk_pmu_niu",
-     "pclk_core_niu",
-     "pclk_ddrupctl0",
-     "pclk_publ0",
-     "pclk_ddrupctl1",
-     "pclk_publ1",
 

These clks needed enable, device node not use this clk, so we mark it as critical.

What breaks if you don't enable these clocks? As far as I can tell these clocks only need to be enabled while touching memory controller registers (deep suspend/resume and DDRFreq transitions). On Chromebooks everything works fine with these clocks only turned on when needed.

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

If need to enable these clks, ddrupctl0/ddrupctl1/publ0/publ1 clks no driver to handle them, so mark these clk as critical.

Perhaps it's just a typo, but you say "If need to enable". I see no evidence that these clocks need to be enabled unless there is code touching memory controller registers. Thus we don't need to enable them so they don't need to be critical.

yep ... maybe Elaine can clarify in what other activities these clocks are needed ... I guess any ddr-scaling code would activate them before touching memory-controller-registers.

OK, I agree.

I rechecked the clocks.It does get turned on before touching memory-controller-registers.

The old DDR drivers are not going to control these clks, so we marked it as critical.

The latest DDR drivers are already  supported activate them before touching memory-controller-registers.

Sorry. it's my fault.

Quoted 37 lines
Quoted 31 lines
Quoted 17 lines

- "pmu_hclk_otg0",

It's a soc bug, pmu_hclk_otg0 must always on.

So you said in your previous commit message. However we've shipped lots and lots of Chromebooks with this clock off. Can you explain what is broken? Is this only needed for gadget mode (which we don't use), for instance?

test case:

recovery test, < 1 hour , system crash.

log:

Quoted 9 lines
[  127.569629] I[0:      swapper/0:    0] GOTGCTL        @0xFFFFFF8000B80000 : 0x00400010
[  127.569644] I[0:      swapper/0:    0] GOTGINT        @0xFFFFFF8000B80004 : 0x00400010
[  127.569659] I[0:      swapper/0:    0] GAHBCFG        @0xFFFFFF8000B80008 : 0x00400010
[  127.569673] I[0:      swapper/0:    0] GUSBCFG        @0xFFFFFF8000B8000C : 0x00400010
[  127.569688] I[0:      swapper/0:    0] GRSTCTL        @0xFFFFFF8000B80010 : 0x00400010
[  127.569702] I[0:      swapper/0:    0] GINTSTS        @0xFFFFFF8000B80014 : 0x00400010
[  127.569718] I[0:      swapper/0:    0] GINTMSK        @0xFFFFFF8000B80018 : 0x00400010
[  127.569733] I[0:      swapper/0:    0] GRXSTSR        @0xFFFFFF8000B8001C : 0x00400010
[  127.569748] I[0:      swapper/0:    0] GRXFSIZ        @0xFFFFFF8000B80024 : 0x00400010

I don't know what a "recovery test" is and I don't understand your logs.

Can you explain we do not run into this on Chromebooks?

Quoted 6 lines
Quoted 3 lines

reason:

USB OTG controller supports turning off most logic power, and then only one PMU module is left. This clock cannot be turned off, which is similar to the always on module in USB OTG.

Can't you just add a patch to the dwc2 driver to have it grab this clock? I assume this clock doesn't need to be turned on unless you're using the OTG contoller in a certain way?

Quoted 6 lines

So far we don't really know where the clock in question is sitting in the clock hirarchy. For example the kernel got a new interconnect framework recently, so handling non-device clocks in a device may haunt us later on.

@Elaine: could you elaborate what pmu_hclk_otg0 actually is for please?

Doug:

Recovry test: Regular factory tests, including restart, adb debugging, clear data/factory Settings, and clear cache. I'm not clear whether the test was added by chromebooks.

Heiko:

pmu_hclk_otg0: pmu ahb clock

Function: Clock to pmu module when hibernation and/or ADP is enabled.Must be greater than or equal to 30 MHz.

If the SOC design does not support hibernation/ADP function, only have hclk_otg, this clk can be switched according to the usage of otg. If the SOC design support hibernation/ADP, has two clocks, hclk_otg and pmu_hclk_otg0.
Hclk_otg belongs to the closed part of otg logic, which can be switched according to the use of otg.

pmu_hclk_otg0 belongs to the always on part.

As for whether pmu_hclk_otg0 can be turned off when otg is not in use, we have not tested. IC suggest make pmu_hclk_otg0 always on.

Quoted 5 lines
Quoted 5 lines

NOTE: nowhere in your responses did you talk about why "hsicphy12m_xin12m" needed to be marked as IGNORE_UNUSED. I guess you're OK with removing that?

Yes, I agree.

Quoted 8 lines

Thanks
Heiko

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#8 lore raw

Re: [PATCH 1/3] Revert "clk: rockchip: mark noc and some special clk as critical on rk3288"

Hi,

Quoted 48 lines · elaine.zhang
Quoted 35 lines
Quoted 29 lines
Quoted 15 lines

- "pmu_hclk_otg0",

It's a soc bug, pmu_hclk_otg0 must always on.

So you said in your previous commit message. However we've shipped lots and lots of Chromebooks with this clock off. Can you explain what is broken? Is this only needed for gadget mode (which we don't use), for instance?

test case:

recovery test, < 1 hour , system crash.

log:

Quoted 9 lines
[  127.569629] I[0:      swapper/0:    0] GOTGCTL        @0xFFFFFF8000B80000 : 0x00400010
[  127.569644] I[0:      swapper/0:    0] GOTGINT        @0xFFFFFF8000B80004 : 0x00400010
[  127.569659] I[0:      swapper/0:    0] GAHBCFG        @0xFFFFFF8000B80008 : 0x00400010
[  127.569673] I[0:      swapper/0:    0] GUSBCFG        @0xFFFFFF8000B8000C : 0x00400010
[  127.569688] I[0:      swapper/0:    0] GRSTCTL        @0xFFFFFF8000B80010 : 0x00400010
[  127.569702] I[0:      swapper/0:    0] GINTSTS        @0xFFFFFF8000B80014 : 0x00400010
[  127.569718] I[0:      swapper/0:    0] GINTMSK        @0xFFFFFF8000B80018 : 0x00400010
[  127.569733] I[0:      swapper/0:    0] GRXSTSR        @0xFFFFFF8000B8001C : 0x00400010
[  127.569748] I[0:      swapper/0:    0] GRXFSIZ        @0xFFFFFF8000B80024 : 0x00400010

I don't know what a "recovery test" is and I don't understand your logs.

Can you explain we do not run into this on Chromebooks?

Quoted 6 lines
Quoted 3 lines

reason:

USB OTG controller supports turning off most logic power, and then only one PMU module is left. This clock cannot be turned off, which is similar to the always on module in USB OTG.

Can't you just add a patch to the dwc2 driver to have it grab this clock? I assume this clock doesn't need to be turned on unless you're using the OTG contoller in a certain way?

Quoted 6 lines

So far we don't really know where the clock in question is sitting in the clock hirarchy. For example the kernel got a new interconnect framework recently, so handling non-device clocks in a device may haunt us later on.

@Elaine: could you elaborate what pmu_hclk_otg0 actually is for please?

Doug:

Recovry test: Regular factory tests, including restart, adb debugging, clear data/factory Settings, and clear cache.
I'm not clear whether the test was added by chromebooks.

Quoted 6 lines

Heiko:

pmu_hclk_otg0: pmu ahb clock

Function: Clock to pmu module when hibernation and/or ADP is enabled.Must be greater than or equal to 30 MHz.

Does this mean we can enable hibernation in dwc2 once we turn this clock on? I think right now hibernation doesn't work for dwc2 on rk3288. Not that I know a ton about dwc2's hibernation modes, but I've certainly bumped up against it when enabling power down modes. In fact I'm planning to post some patches soon... I'll CC you.

Quoted 11 lines

If the SOC design does not support hibernation/ADP function, only have hclk_otg, this clk can be switched according to the usage of otg. If the SOC design support hibernation/ADP, has two clocks, hclk_otg and pmu_hclk_otg0.
Hclk_otg belongs to the closed part of otg logic, which can be switched according to the use of otg.

pmu_hclk_otg0 belongs to the always on part.

As for whether pmu_hclk_otg0 can be turned off when otg is not in use, we have not tested. IC suggest make pmu_hclk_otg0 always on.

OK. I'm fine with this clock staying as a critical clock for now.

I'll send out a v2 shortly.

-Doug

#9 lore raw

PATCH 2/3 clk: rockchip: Make rkpwm a critical clock on rk3288

In reply to Douglas Anderson

Most rk3288-based boards are derived from the EVB and thus use a PWM regulator for the logic rail. However, most rk3288-based boards don't specify the PWM regulator in their device tree. We'll deal with that by making it critical.

NOTE: it's important to make it critical and not just IGNORE_UNUSED because all PWMs in the system share the same clock. We don't want another PWM user to turn the clock on and off and kill the logic rail.

This change is in preparation for actually having the PWMs in the rk3288 device tree actually point to the proper PWM clock. Up until now they've all pointed to the clock for the old IP block and they've all worked due to the fact that rkpwm was IGNORE_UNUSED and that the clock rates for both clocks were the same.

---

 drivers/clk/rockchip/clk-rk3288.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3288.c +2 -1
index 06287810474e..c3321eade23e 100644
@@ -697,7 +697,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
 	GATE(PCLK_TZPC, "pclk_tzpc", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 3, GFLAGS),
 	GATE(PCLK_UART2, "pclk_uart2", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 9, GFLAGS),
 	GATE(PCLK_EFUSE256, "pclk_efuse_256", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 10, GFLAGS),
-	GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 11, GFLAGS),
+	GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 11, GFLAGS),
 
 	/* ddrctrl [DDR Controller PHY clock] gates */
 	GATE(0, "nclk_ddrupctl0", "ddrphy", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 4, GFLAGS),
@@ -837,6 +837,7 @@ static const char *const rk3288_critical_clocks[] __initconst = {
 	"pclk_alive_niu",
 	"pclk_pd_pmu",
 	"pclk_pmu_niu",
+	"pclk_rkpwm",
 };
 
 static void __iomem *rk3288_cru_base;
Signature · 1 line
2.21.0.392.gf8f6787159e-goog
#10 lore raw

Re: [PATCH 2/3] clk: rockchip: Make rkpwm a critical clock on rk3288

hi,

Quoted 35 lines · Douglas Anderson

Most rk3288-based boards are derived from the EVB and thus use a PWM regulator for the logic rail. However, most rk3288-based boards don't specify the PWM regulator in their device tree. We'll deal with that by making it critical.

NOTE: it's important to make it critical and not just IGNORE_UNUSED because all PWMs in the system share the same clock. We don't want another PWM user to turn the clock on and off and kill the logic rail.

This change is in preparation for actually having the PWMs in the rk3288 device tree actually point to the proper PWM clock. Up until now they've all pointed to the clock for the old IP block and they've all worked due to the fact that rkpwm was IGNORE_UNUSED and that the clock rates for both clocks were the same.

---

  drivers/clk/rockchip/clk-rk3288.c | 3 ++-
  1 file changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3288.c +1 -1
index 06287810474e..c3321eade23e 100644
@@ -697,7 +697,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
  	GATE(PCLK_TZPC, "pclk_tzpc", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 3, GFLAGS),
  	GATE(PCLK_UART2, "pclk_uart2", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 9, GFLAGS),
  	GATE(PCLK_EFUSE256, "pclk_efuse_256", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 10, GFLAGS),
-	GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 11, GFLAGS),
+	GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 11, GFLAGS),
 
  	/* ddrctrl [DDR Controller PHY clock] gates */
  	GATE(0, "nclk_ddrupctl0", "ddrphy", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 4, GFLAGS),

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 840

Quoted 4 lines
drivers/clk/rockchip/clk-rk3288.c +1 -0
@@ -837,6 +837,7 @@ static const char *const rk3288_critical_clocks[] __initconst = {
  	"pclk_alive_niu",
  	"pclk_pd_pmu",
  	"pclk_pmu_niu",
+	"pclk_rkpwm",

pwm have device node, can enable and disable it in the pwm drivers.

pwm regulator use pwm node as:

pwms = <&pwm2 0 25000 1>

when set Logic voltage:

pwm_regulator_set_voltage()

    --> pwm_apply_state()

        -->clk_enable()

        -->pwm_enable()

        -->pwm_config()

        -->pinctrl_select()

        --....

For mark pclk_rkpwm as critical,do you have any questions, or provides some log or more information.

Quoted 3 lines
drivers/clk/rockchip/clk-rk3288.c +0 -0
  };
 
  static void __iomem *rk3288_cru_base;
#11 lore raw

Re: [PATCH 2/3] clk: rockchip: Make rkpwm a critical clock on rk3288

Hi,

Quoted 66 lines · elaine.zhang

hi,

Quoted 35 lines · Douglas Anderson

Most rk3288-based boards are derived from the EVB and thus use a PWM regulator for the logic rail. However, most rk3288-based boards don't specify the PWM regulator in their device tree. We'll deal with that by making it critical.

NOTE: it's important to make it critical and not just IGNORE_UNUSED because all PWMs in the system share the same clock. We don't want another PWM user to turn the clock on and off and kill the logic rail.

This change is in preparation for actually having the PWMs in the rk3288 device tree actually point to the proper PWM clock. Up until now they've all pointed to the clock for the old IP block and they've all worked due to the fact that rkpwm was IGNORE_UNUSED and that the clock rates for both clocks were the same.

---

  drivers/clk/rockchip/clk-rk3288.c | 3 ++-
  1 file changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3288.c +1 -1
index 06287810474e..c3321eade23e 100644
@@ -697,7 +697,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
      GATE(PCLK_TZPC, "pclk_tzpc", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 3, GFLAGS),
      GATE(PCLK_UART2, "pclk_uart2", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 9, GFLAGS),
      GATE(PCLK_EFUSE256, "pclk_efuse_256", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 10, GFLAGS),
-     GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 11, GFLAGS),
+     GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 11, GFLAGS),
 
      /* ddrctrl [DDR Controller PHY clock] gates */
      GATE(0, "nclk_ddrupctl0", "ddrphy", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 4, GFLAGS),

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 840

Quoted 4 lines
drivers/clk/rockchip/clk-rk3288.c +1 -0
@@ -837,6 +837,7 @@ static const char *const rk3288_critical_clocks[] __initconst = {
      "pclk_alive_niu",
      "pclk_pd_pmu",
      "pclk_pmu_niu",
+     "pclk_rkpwm",

pwm have device node, can enable and disable it in the pwm drivers.

pwm regulator use pwm node as:

pwms = <&pwm2 0 25000 1>

when set Logic voltage:

pwm_regulator_set_voltage()

     --> pwm_apply_state()

         -->clk_enable()

         -->pwm_enable()

         -->pwm_config()

         -->pinctrl_select()

         --....
Quoted 2 lines

For mark pclk_rkpwm as critical,do you have any questions, or provides some log or more information.

Right, if we actually specify the PWM used for the PWM regulator in the device tree then there is no need to mark it as a critical clock. In fact rk3288-veyron devices boot absolutely fine without marking this clock as critical. Actually, it seems like the way the PWM framework works (IIRC it was designed this way specifically to support PWM regulators) is that even just specifying that pwm1 is "okay" is enough to keep the clock on even if the PWM regulator isn't specified.

...however...

Take a look at, for instance, the rk3288-evb device tree file. Nowhere in there does it specify that the PWM used for the PWM regulator should be on. Presumably that means that if we don't mark the clock as critical then rk3288-evb will fail to boot. That's easy for me to fix since I have the rk3288-evb schematics, but what about other rk3288 boards? We could make educated guesses about each of them and/or fix things are we hear about breakages.

...but...

All the above would only be worth doing if we thought someone would get some benefit out of it. I'd bet that pretty much all rk3288-based boards use a PWM regulator. Thus, in reality, everyone will want the rkpwm clock on all the time anyway. In that case going through all that extra work / potentially breaking other boards doesn't seem worth it. Just mark the clock as critical.

-Doug

#12 lore raw

Re: [PATCH 2/3] clk: rockchip: Make rkpwm a critical clock on rk3288

hi,

Quoted 87 lines · Doug Anderson

Hi,

Quoted 64 lines · elaine.zhang

hi,

Quoted 35 lines · Douglas Anderson

Most rk3288-based boards are derived from the EVB and thus use a PWM regulator for the logic rail. However, most rk3288-based boards don't specify the PWM regulator in their device tree. We'll deal with that by making it critical.

NOTE: it's important to make it critical and not just IGNORE_UNUSED because all PWMs in the system share the same clock. We don't want another PWM user to turn the clock on and off and kill the logic rail.

This change is in preparation for actually having the PWMs in the rk3288 device tree actually point to the proper PWM clock. Up until now they've all pointed to the clock for the old IP block and they've all worked due to the fact that rkpwm was IGNORE_UNUSED and that the clock rates for both clocks were the same.

---

   drivers/clk/rockchip/clk-rk3288.c | 3 ++-
   1 file changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3288.c +1 -1
index 06287810474e..c3321eade23e 100644
@@ -697,7 +697,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
       GATE(PCLK_TZPC, "pclk_tzpc", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 3, GFLAGS),
       GATE(PCLK_UART2, "pclk_uart2", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 9, GFLAGS),
       GATE(PCLK_EFUSE256, "pclk_efuse_256", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 10, GFLAGS),
-     GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 11, GFLAGS),
+     GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 11, GFLAGS),
 
       /* ddrctrl [DDR Controller PHY clock] gates */
       GATE(0, "nclk_ddrupctl0", "ddrphy", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 4, GFLAGS),

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 840

Quoted 4 lines
drivers/clk/rockchip/clk-rk3288.c +1 -0
@@ -837,6 +837,7 @@ static const char *const rk3288_critical_clocks[] __initconst = {
       "pclk_alive_niu",
       "pclk_pd_pmu",
       "pclk_pmu_niu",
+     "pclk_rkpwm",

pwm have device node, can enable and disable it in the pwm drivers.

pwm regulator use pwm node as:

pwms = <&pwm2 0 25000 1>

when set Logic voltage:

pwm_regulator_set_voltage()

      --> pwm_apply_state()

          -->clk_enable()

          -->pwm_enable()

          -->pwm_config()

          -->pinctrl_select()

          --....
Quoted 2 lines

For mark pclk_rkpwm as critical,do you have any questions, or provides some log or more information.

Right, if we actually specify the PWM used for the PWM regulator in the device tree then there is no need to mark it as a critical clock. In fact rk3288-veyron devices boot absolutely fine without marking this clock as critical. Actually, it seems like the way the PWM framework works (IIRC it was designed this way specifically to support PWM regulators) is that even just specifying that pwm1 is "okay" is enough to keep the clock on even if the PWM regulator isn't specified.

...however...

Take a look at, for instance, the rk3288-evb device tree file. Nowhere in there does it specify that the PWM used for the PWM regulator should be on. Presumably that means that if we don't mark the clock as critical then rk3288-evb will fail to boot. That's easy for me to fix since I have the rk3288-evb schematics, but what about other rk3288 boards? We could make educated guesses about each of them and/or fix things are we hear about breakages.

Quoted 8 lines

...but...

All the above would only be worth doing if we thought someone would get some benefit out of it. I'd bet that pretty much all rk3288-based boards use a PWM regulator. Thus, in reality, everyone will want the rkpwm clock on all the time anyway. In that case going through all that extra work / potentially breaking other boards doesn't seem worth it. Just mark the clock as critical.

I have no problem with changing it like this, but I think it is better to modify dts:

vdd_log: vdd-log {
        compatible = "pwm-regulator";
        rockchip,pwm_id = <2>; //for rk uboot rockchip,pwm_voltage = <900000>; // for rk uboot pwms = <&pwm2 0 25000 1>;
        regulator-name = "vdd_log"; regulator-min-microvolt = <800000>;//hw logic min voltage regulator-max-microvolt = <1400000>;//hw logic max voltage regulator-always-on;
        regulator-boot-on;
    };

Maybe we did not push the modification of this part in rk3288-evb, I will push to deal with this.(rk3229-evb.dts and rk3399 has been already pushed)

Quoted 8 lines

-Doug

#13 lore raw

Re: [PATCH 2/3] clk: rockchip: Make rkpwm a critical clock on rk3288

Hi,

Quoted 115 lines · elaine.zhang

hi,

Quoted 87 lines · Doug Anderson

Hi,

Quoted 64 lines · elaine.zhang

hi,

Quoted 35 lines · Douglas Anderson

Most rk3288-based boards are derived from the EVB and thus use a PWM regulator for the logic rail. However, most rk3288-based boards don't specify the PWM regulator in their device tree. We'll deal with that by making it critical.

NOTE: it's important to make it critical and not just IGNORE_UNUSED because all PWMs in the system share the same clock. We don't want another PWM user to turn the clock on and off and kill the logic rail.

This change is in preparation for actually having the PWMs in the rk3288 device tree actually point to the proper PWM clock. Up until now they've all pointed to the clock for the old IP block and they've all worked due to the fact that rkpwm was IGNORE_UNUSED and that the clock rates for both clocks were the same.

---

   drivers/clk/rockchip/clk-rk3288.c | 3 ++-
   1 file changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3288.c +1 -1
index 06287810474e..c3321eade23e 100644
@@ -697,7 +697,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
       GATE(PCLK_TZPC, "pclk_tzpc", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 3, GFLAGS),
       GATE(PCLK_UART2, "pclk_uart2", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 9, GFLAGS),
       GATE(PCLK_EFUSE256, "pclk_efuse_256", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 10, GFLAGS),
-     GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 11, GFLAGS),
+     GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 11, GFLAGS),
 
       /* ddrctrl [DDR Controller PHY clock] gates */
       GATE(0, "nclk_ddrupctl0", "ddrphy", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 4, GFLAGS),

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 840

Quoted 4 lines
drivers/clk/rockchip/clk-rk3288.c +1 -0
@@ -837,6 +837,7 @@ static const char *const rk3288_critical_clocks[] __initconst = {
       "pclk_alive_niu",
       "pclk_pd_pmu",
       "pclk_pmu_niu",
+     "pclk_rkpwm",

pwm have device node, can enable and disable it in the pwm drivers.

pwm regulator use pwm node as:

pwms = <&pwm2 0 25000 1>

when set Logic voltage:

pwm_regulator_set_voltage()

      --> pwm_apply_state()

          -->clk_enable()

          -->pwm_enable()

          -->pwm_config()

          -->pinctrl_select()

          --....
Quoted 2 lines

For mark pclk_rkpwm as critical,do you have any questions, or provides some log or more information.

Right, if we actually specify the PWM used for the PWM regulator in the device tree then there is no need to mark it as a critical clock. In fact rk3288-veyron devices boot absolutely fine without marking this clock as critical. Actually, it seems like the way the PWM framework works (IIRC it was designed this way specifically to support PWM regulators) is that even just specifying that pwm1 is "okay" is enough to keep the clock on even if the PWM regulator isn't specified.

...however...

Take a look at, for instance, the rk3288-evb device tree file. Nowhere in there does it specify that the PWM used for the PWM regulator should be on. Presumably that means that if we don't mark the clock as critical then rk3288-evb will fail to boot. That's easy for me to fix since I have the rk3288-evb schematics, but what about other rk3288 boards? We could make educated guesses about each of them and/or fix things are we hear about breakages.

Quoted 8 lines

...but...

All the above would only be worth doing if we thought someone would get some benefit out of it. I'd bet that pretty much all rk3288-based boards use a PWM regulator. Thus, in reality, everyone will want the rkpwm clock on all the time anyway. In that case going through all that extra work / potentially breaking other boards doesn't seem worth it. Just mark the clock as critical.

I have no problem with changing it like this, but I think it is better to modify dts:

vdd_log: vdd-log {
         compatible = "pwm-regulator";
         rockchip,pwm_id = <2>; //for rk uboot
         rockchip,pwm_voltage = <900000>; // for rk uboot
         pwms = <&pwm2 0 25000 1>;
         regulator-name = "vdd_log";
         regulator-min-microvolt = <800000>;//hw logic min voltage
         regulator-max-microvolt = <1400000>;//hw logic max voltage
         regulator-always-on;
         regulator-boot-on;
     };
Quoted 3 lines

Maybe we did not push the modification of this part in rk3288-evb, I will push to deal with this.(rk3229-evb.dts and rk3399 has been already pushed)

Heiko: do you have advice for how you'd like this to proceed? We could certainly land patch #3 in this series without patch #2 and then pick up the pieces as we find boards that no longer boot. As I've argued I'm not sure that's worth the effort, but I'll leave it up to you.

-Doug

maintainer
#14 lore raw

Re: [PATCH 2/3] clk: rockchip: Make rkpwm a critical clock on rk3288

Hi Doug, Elaine,

Am Donnerstag, 11. April 2019, 16:42:23 CEST schrieb Doug Anderson:

Quoted 113 lines · elaine.zhang
Quoted 108 lines · Doug Anderson
Quoted 83 lines · elaine.zhang
Quoted 62 lines · Douglas Anderson
Quoted 35 lines

Most rk3288-based boards are derived from the EVB and thus use a PWM regulator for the logic rail. However, most rk3288-based boards don't specify the PWM regulator in their device tree. We'll deal with that by making it critical.

NOTE: it's important to make it critical and not just IGNORE_UNUSED because all PWMs in the system share the same clock. We don't want another PWM user to turn the clock on and off and kill the logic rail.

This change is in preparation for actually having the PWMs in the rk3288 device tree actually point to the proper PWM clock. Up until now they've all pointed to the clock for the old IP block and they've all worked due to the fact that rkpwm was IGNORE_UNUSED and that the clock rates for both clocks were the same.

---

   drivers/clk/rockchip/clk-rk3288.c | 3 ++-
   1 file changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3288.c +1 -1
index 06287810474e..c3321eade23e 100644
@@ -697,7 +697,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
       GATE(PCLK_TZPC, "pclk_tzpc", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 3, GFLAGS),
       GATE(PCLK_UART2, "pclk_uart2", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 9, GFLAGS),
       GATE(PCLK_EFUSE256, "pclk_efuse_256", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 10, GFLAGS),
-     GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 11, GFLAGS),
+     GATE(PCLK_RKPWM, "pclk_rkpwm", "pclk_cpu", 0, RK3288_CLKGATE_CON(11), 11, GFLAGS),
 
       /* ddrctrl [DDR Controller PHY clock] gates */
       GATE(0, "nclk_ddrupctl0", "ddrphy", CLK_IGNORE_UNUSED, RK3288_CLKGATE_CON(11), 4, GFLAGS),

drivers/clk/rockchip/clk-rk3288.c static const char *const rk3288_critical_clocks[] __initconst = { · line 840

Quoted 4 lines
drivers/clk/rockchip/clk-rk3288.c +1 -0
@@ -837,6 +837,7 @@ static const char *const rk3288_critical_clocks[] __initconst = {
       "pclk_alive_niu",
       "pclk_pd_pmu",
       "pclk_pmu_niu",
+     "pclk_rkpwm",

pwm have device node, can enable and disable it in the pwm drivers.

pwm regulator use pwm node as:

pwms = <&pwm2 0 25000 1>

when set Logic voltage:

pwm_regulator_set_voltage()

      --> pwm_apply_state()

          -->clk_enable()

          -->pwm_enable()

          -->pwm_config()

          -->pinctrl_select()

          --....
Quoted 2 lines

For mark pclk_rkpwm as critical,do you have any questions, or provides some log or more information.

Right, if we actually specify the PWM used for the PWM regulator in the device tree then there is no need to mark it as a critical clock. In fact rk3288-veyron devices boot absolutely fine without marking this clock as critical. Actually, it seems like the way the PWM framework works (IIRC it was designed this way specifically to support PWM regulators) is that even just specifying that pwm1 is "okay" is enough to keep the clock on even if the PWM regulator isn't specified.

...however...

Take a look at, for instance, the rk3288-evb device tree file. Nowhere in there does it specify that the PWM used for the PWM regulator should be on. Presumably that means that if we don't mark the clock as critical then rk3288-evb will fail to boot. That's easy for me to fix since I have the rk3288-evb schematics, but what about other rk3288 boards? We could make educated guesses about each of them and/or fix things are we hear about breakages.

Quoted 8 lines

...but...

All the above would only be worth doing if we thought someone would get some benefit out of it. I'd bet that pretty much all rk3288-based boards use a PWM regulator. Thus, in reality, everyone will want the rkpwm clock on all the time anyway. In that case going through all that extra work / potentially breaking other boards doesn't seem worth it. Just mark the clock as critical.

I have no problem with changing it like this, but I think it is better to modify dts:

vdd_log: vdd-log {
         compatible = "pwm-regulator";
         rockchip,pwm_id = <2>; //for rk uboot
         rockchip,pwm_voltage = <900000>; // for rk uboot
         pwms = <&pwm2 0 25000 1>;
         regulator-name = "vdd_log";
         regulator-min-microvolt = <800000>;//hw logic min voltage
         regulator-max-microvolt = <1400000>;//hw logic max voltage
         regulator-always-on;
         regulator-boot-on;
     };
Quoted 3 lines

Maybe we did not push the modification of this part in rk3288-evb, I will push to deal with this.(rk3229-evb.dts and rk3399 has been already pushed)

Quoted 5 lines

Heiko: do you have advice for how you'd like this to proceed? We could certainly land patch #3 in this series without patch #2 and then pick up the pieces as we find boards that no longer boot. As I've argued I'm not sure that's worth the effort, but I'll leave it up to you.

So I've skimmed through a number of rk3288 device-schematics and at least there pwm-based logic-regulator is only part of some of the rk808-based designs. All the act8846-based boards use one of its regulator-outputs for the logic supply. So this matters for at least the veyron-boards and the rk3288-evb ... but not the phycore.

But it also is part of a vital system for veyron and they won't really like if somewhere during probe the pwm-clock gets turned off ;-) .

So I tend to agree with Doug and will just apply the make-critical patch. If Stephen's "handoff" clock-type [critical until a driver claims it] materializes some-time, we can switch to that.

Heiko

maintainer
#15 lore raw

Re: [PATCH 2/3] clk: rockchip: Make rkpwm a critical clock on rk3288

In reply to Douglas Anderson

Am Dienstag, 9. April 2019, 22:47:06 CEST schrieb Douglas Anderson:

Quoted 9 lines

Most rk3288-based boards are derived from the EVB and thus use a PWM regulator for the logic rail. However, most rk3288-based boards don't specify the PWM regulator in their device tree. We'll deal with that by making it critical.

NOTE: it's important to make it critical and not just IGNORE_UNUSED because all PWMs in the system share the same clock. We don't want another PWM user to turn the clock on and off and kill the logic rail.

Quoted 7 lines

This change is in preparation for actually having the PWMs in the rk3288 device tree actually point to the proper PWM clock. Up until now they've all pointed to the clock for the old IP block and they've all worked due to the fact that rkpwm was IGNORE_UNUSED and that the clock rates for both clocks were the same.

applied for 5.2
I've added a comment line describing the pwm-reg reason.

Heiko

#16 lore raw

PATCH 3/3 ARM: dts: rockchip: fix PWM clock found on RK3288 Socs

In reply to Douglas Anderson

From: Caesar Wang <[email protected]>

We use the new PWM IP on RK3288, but the PWM's clock indeed incorrect.

---

 arch/arm/boot/dts/rk3288.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm/boot/dts/rk3288.dtsi +4 -4
index 8bce2fc49b24..efdfa3737561 100644
@@ -677,7 +677,7 @@
 		#pwm-cells = <3>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm0_pin>;
-		clocks = <&cru PCLK_PWM>;
+		clocks = <&cru PCLK_RKPWM>;
 		clock-names = "pwm";
 		status = "disabled";
 	};
@@ -688,7 +688,7 @@
 		#pwm-cells = <3>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm1_pin>;
-		clocks = <&cru PCLK_PWM>;
+		clocks = <&cru PCLK_RKPWM>;
 		clock-names = "pwm";
 		status = "disabled";
 	};
@@ -699,7 +699,7 @@
 		#pwm-cells = <3>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm2_pin>;
-		clocks = <&cru PCLK_PWM>;
+		clocks = <&cru PCLK_RKPWM>;
 		clock-names = "pwm";
 		status = "disabled";
 	};
@@ -710,7 +710,7 @@
 		#pwm-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm3_pin>;
-		clocks = <&cru PCLK_PWM>;
+		clocks = <&cru PCLK_RKPWM>;
 		clock-names = "pwm";
 		status = "disabled";
 	};
Signature · 1 line
2.21.0.392.gf8f6787159e-goog
maintainer Applied
#17 lore raw

Re: [PATCH 3/3] ARM: dts: rockchip: fix PWM clock found on RK3288 Socs

Am Dienstag, 9. April 2019, 22:47:07 CEST schrieb Douglas Anderson:

Quoted 6 lines

From: Caesar Wang <[email protected]>

We use the new PWM IP on RK3288, but the PWM's clock indeed incorrect.

applied into a branch for 5._3_ ... as it requires a change coming through a different tree, the patch gets a "quarantine"-release in between.

Thanks
Heiko