ARM: SAMSUNG: remove unused DMA infrastructure

deleted file mode 100644
index 3ed82383efea..000000000000
@@ -1,46 +0,0 @@
-			S3C2410 DMA
-			===========
-
-Introduction
-------------
-
-   The kernel provides an interface to manage DMA transfers
-   using the DMA channels in the CPU, so that the central
-   duty of managing channel mappings, and programming the
-   channel generators is in one place.
-
-
-DMA Channel Ordering
---------------------
-
-   Many of the range do not have connections for the DMA
-   channels to all sources, which means that some devices
-   have a restricted number of channels that can be used.
-
-   To allow flexibility for each CPU type and board, the
-   DMA code can be given a DMA ordering structure which
-   allows the order of channel search to be specified, as
-   well as allowing the prohibition of certain claims.
-
-   struct s3c24xx_dma_order has a list of channels, and
-   each channel within has a slot for a list of DMA
-   channel numbers. The slots are searched in order for
-   the presence of a DMA channel number with DMA_CH_VALID
-   or-ed in.
-
-   If the order has the flag DMA_CH_NEVER set, then after
-   checking the channel list, the system will return no
-   found channel, thus denying the request.
-
-   A board support file can call s3c24xx_dma_order_set()
-   to register a complete ordering set. The routine will
-   copy the data, so the original can be discarded with
-   __initdata.
-
-
-Authour
--------
-
-Ben Dooks,
-Copyright (c) 2007 Ben Dooks, Simtec Electronics
-Licensed under the GPL v2

102 lines not on this page · raw message

index b92071638733..b40a22fe082a 100644
@@ -12,12 +12,10 @@
 obj-y				+= common.o
 
 obj-$(CONFIG_CPU_S3C2410)	+= s3c2410.o
-obj-$(CONFIG_S3C2410_DMA)	+= dma-s3c2410.o
 obj-$(CONFIG_S3C2410_PLL)	+= pll-s3c2410.o
 obj-$(CONFIG_S3C2410_PM)	+= pm-s3c2410.o sleep-s3c2410.o
 
 obj-$(CONFIG_CPU_S3C2412)	+= s3c2412.o
-obj-$(CONFIG_S3C2412_DMA)	+= dma-s3c2412.o
 obj-$(CONFIG_S3C2412_PM)	+= pm-s3c2412.o
 obj-$(CONFIG_S3C2412_PM_SLEEP)	+= sleep-s3c2412.o
 

@@ -27,7 +25,6 @@ obj-$(CONFIG_S3C2416_PM)	+= pm-s3c2416.o
 obj-$(CONFIG_CPU_S3C2440)	+= s3c2440.o
 obj-$(CONFIG_CPU_S3C2442)	+= s3c2442.o
 obj-$(CONFIG_CPU_S3C244X)	+= s3c244x.o
-obj-$(CONFIG_S3C2440_DMA)	+= dma-s3c2440.o
 obj-$(CONFIG_S3C2440_PLL_12000000) += pll-s3c2440-12000000.o
 obj-$(CONFIG_S3C2440_PLL_16934400) += pll-s3c2440-16934400.o
 

@@ -39,15 +36,11 @@ obj-$(CONFIG_PM)		+= pm.o irq-pm.o sleep.o
 
 # common code
 
-obj-$(CONFIG_S3C24XX_DMA)	+= dma.o
-
 obj-$(CONFIG_S3C2410_CPUFREQ_UTILS) += cpufreq-utils.o
 
 obj-$(CONFIG_S3C2410_IOTIMING)	+= iotiming-s3c2410.o
 obj-$(CONFIG_S3C2412_IOTIMING)	+= iotiming-s3c2412.o
 
-obj-$(CONFIG_S3C2443_DMA)	+= dma-s3c2443.o
-
 #
 # machine support
 # following is ordered alphabetically by option text.

index 9bd2776e7d05..cb8e3d655d1a 100644
@@ -236,13 +236,6 @@ config S3C_SETUP_CAMIF
 	help
 	  Compile in common setup code for S3C CAMIF devices
 
-# DMA
-
-config S3C_DMA
-	bool
-	help
-	  Internal configuration for S3C DMA core
-
 config SAMSUNG_PM_GPIO
 	bool
 	default y if GPIO_SAMSUNG && PM

@@ -250,14 +243,6 @@ config SAMSUNG_PM_GPIO
 	  Include legacy GPIO power management code for platforms not using
 	  pinctrl-samsung driver.
 
-config SAMSUNG_DMADEV
-	bool "Use legacy Samsung DMA abstraction"
-	depends on CPU_S5PV210 || ARCH_S3C64XX
-	select DMADEVICES
-	default y
-	help
-	  Use DMA device engine for PL330 DMAC.
-
 endif
 
 config S5P_DEV_MFC

index 87746c37f030..1a29ab1f446d 100644
@@ -26,12 +26,6 @@ obj-$(CONFIG_SAMSUNG_DEV_BACKLIGHT)	+= dev-backlight.o
 
 obj-$(CONFIG_S3C_SETUP_CAMIF)	+= setup-camif.o
 
-# DMA support
-
-obj-$(CONFIG_S3C_DMA)		+= dma.o s3c-dma-ops.o
-
-obj-$(CONFIG_SAMSUNG_DMADEV)	+= dma-ops.o
-
 # PM support
 
 obj-$(CONFIG_PM_SLEEP)		+= pm-common.o

index f2b2c4e87aef..faf30a4e642b 100644

Lines of this file are not shown. View the raw message.