Skip to contentSkip to conversation

UBoot configuration for T-Engine/SH7727 MS7727CP02 DevKit

U-Boot-Users thaoth 4 participants 20 messages Aug 7, 2008 – Sep 12, 2008

lore
Share & tools
lore

thaoth

author
#0 lore raw

Dear All,

I would like to port a Uboot loader on T-Engine/SH7727 MS7727CP02 DevKit. Here is the configuration of this board

Renesas Technology SH7727(SH3-DSP, internal clock 96MHz / external clock 48MHz)
Flash Memory: 8MB
SDRAM: 32MB

Memory map of overall system is shown as below.

0x00000000 +-------------------------------+--------
| User area (P0)|
0x10000000 +-------------------------------+
| (Unused) (P0)| Enabled as a virtual
memory
0x40000000 +-------------------------------+
| System / Common area(1) (P0)|
0x80000000 +-------------------------------+--------
| Physical memory area (P1) |
| (Cache On) |
0xa0000000 +-------------------------------+
| Physical memory area (P2) |
| (Cache Off) |
0xc0000000 +-------------------------------+--------
| System/Common area(2) (P3) | Enabled as a virtual
memory

     0xe0000000 +-------------------------------+--------
                |          I/O area        (P4) |
     0xffffffff +-------------------------------+

Physical memory area (P1 area) memory map is shown as below.

0x80000000 +-------------------------------+--------
| ROM area(8MB) | Area 0
| (Unused area included) |
0x84000000 +-------------------------------+--------
| I/O area | Area 1-2
| (Not used as a general rule)|
0x8c000000 +-------------------------------+--------
| RAM area(64MB) | Area 3
0x90000000 +-------------------------------+--------
| I/O area | Area 4-7
| (Not used as a general rule)|
0xa0000000 +-------------------------------+--------

Here is configuration of UBoot
\board\ms7727se\config.mk : TEXT_BASE = 0x8DFC0000
\board\ms7727se\u-boot.lds

OUTPUT_FORMAT("elf32-sh-tkernel", "elf32-sh-tkernel", "elf32-sh-tkernel") SECTIONS

{
	. = 0x8C000000 + (32*1024*1024) - (256*1024);

\include\configs\ms7727se.h
/* MEMORY */
#define MS7720SE_SDRAM_BASE 0x8C000000
#define MS7720SE_FLASH_BASE_1 0x80000000 //0xA0000000
#define MS7720SE_FLASH_BANK_SIZE (8 * 1024 * 1024)

#define CFG_MEMTEST_START MS7720SE_SDRAM_BASE
#define CFG_MEMTEST_END (CFG_MEMTEST_START + (60 * 1024 * 1024))

#define CFG_SDRAM_BASE MS7720SE_SDRAM_BASE
#define CFG_SDRAM_SIZE (32 * 1024 * 1024)

#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 32 * 1024 * 1024)
#define CFG_MONITOR_BASE MS7720SE_FLASH_BASE_1
#define CFG_MONITOR_LEN (128 * 1024)
#define CFG_MALLOC_LEN (256 * 1024)
#define CFG_GBL_DATA_SIZE 256
#define CFG_BOOTMAPSZ (8 * 1024 * 1024)

/* FLASH */
#define CFG_FLASH_CFI
#define CFG_FLASH_CFI_DRIVER
#undef CFG_FLASH_QUIET_TEST
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */

#define CFG_FLASH_BASE MS7720SE_FLASH_BASE_1

Would you please help me have a look this setting?
1. Is this setting correct ? I am confusing about TEXT_BASE with CFG_LOAD_ADDR. Here is definition
- CFG_FLASH_BASE:
Physical start address of Flash memory.

- CFG_MONITOR_BASE:
Physical start address of boot monitor code (set by make config files to be same as the text base address (TEXT_BASE) used when linking) - same as CFG_FLASH_BASE when booting from flash.

If I am wrong, please tell me how to correct these setting.

2. "ld" T-Engine toolchain only supports elf32-sh-tkernel target, but reference implementation (example) tell "elf32-sh-linux" is expected target. Is the setting correct?

\board\ms7727se\u-boot.lds
Original :
OUTPUT_FORMAT("elf32-sh-linux", "elf32-sh-linux", "elf32-sh-linux") -> My changes
OUTPUT_FORMAT("elf32-sh-tkernel", "elf32-sh-tkernel", "elf32-sh-tkernel")

I am newbie in embedded system. I am appreciating your helping. Thank you a lot.

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p18868090.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#1 lore raw

Hi, thaoth .

2008/8/7 thaoth <[email protected]>:

Quoted 45 lines

Here is configuration of UBoot
\board\ms7727se\config.mk : TEXT_BASE = 0x8DFC0000
\board\ms7727se\u-boot.lds

OUTPUT_FORMAT("elf32-sh-tkernel", "elf32-sh-tkernel", "elf32-sh-tkernel") SECTIONS

{
       . = 0x8C000000 + (32*1024*1024) - (256*1024);

\include\configs\ms7727se.h
/* MEMORY */

#define MS7720SE_SDRAM_BASE             0x8C000000
#define MS7720SE_FLASH_BASE_1           0x80000000 //0xA0000000
#define MS7720SE_FLASH_BANK_SIZE        (8 * 1024 * 1024)

#define CFG_MEMTEST_START MS7720SE_SDRAM_BASE
#define CFG_MEMTEST_END (CFG_MEMTEST_START + (60 * 1024 * 1024))

#define CFG_SDRAM_BASE MS7720SE_SDRAM_BASE
#define CFG_SDRAM_SIZE (32 * 1024 * 1024)

#define CFG_LOAD_ADDR           (CFG_SDRAM_BASE + 32 * 1024 * 1024)
#define CFG_MONITOR_BASE        MS7720SE_FLASH_BASE_1
#define CFG_MONITOR_LEN         (128 * 1024)
#define CFG_MALLOC_LEN          (256 * 1024)
#define CFG_GBL_DATA_SIZE       256
#define CFG_BOOTMAPSZ           (8 * 1024 * 1024)

/* FLASH */
#define CFG_FLASH_CFI
#define CFG_FLASH_CFI_DRIVER
#undef CFG_FLASH_QUIET_TEST
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */

#define CFG_FLASH_BASE MS7720SE_FLASH_BASE_1

Would you please help me have a look this setting?
1. Is this setting correct ? I am confusing about TEXT_BASE with CFG_LOAD_ADDR. Here is definition
- CFG_FLASH_BASE:
Physical start address of Flash memory.

Quoted 5 lines

- CFG_MONITOR_BASE:
Physical start address of boot monitor code (set by make config files to be same as the text base address (TEXT_BASE) used when linking) - same as CFG_FLASH_BASE when booting from flash.

Yes, you are right.
If you use *make config_xx ; make* , you can make an u-boot.srec file starting from the memory (May be address is 0x8DFC000).

I think that you know it, T-engine has a monitor program.
The T-engine user uses this monitor program and writes in it at a flash bulb. However, as for this program, only a SREC file is usable.

If you want make SREC file to Flash, you need to use objcopy command. shX-linux-objcopy -Ibinary -Osrec u-boot.bin u-boot.flash.srec Please check doc/README.sh.

Quoted 7 lines

If I am wrong, please tell me how to correct these setting.

2. "ld" T-Engine toolchain only supports elf32-sh-tkernel target, but reference implementation (example) tell "elf32-sh-linux" is expected target. Is the setting correct?

Quoted 5 lines

\board\ms7727se\u-boot.lds
Original :
OUTPUT_FORMAT("elf32-sh-linux", "elf32-sh-linux", "elf32-sh-linux") -> My changes
OUTPUT_FORMAT("elf32-sh-tkernel", "elf32-sh-tkernel", "elf32-sh-tkernel")

Hmmm, I have not used the tool-chain for t-kernel. However, as for me, there is an acquaintance using t-kernel. I can ask him. And, I will reply about this matter.

Quoted 4 lines

I am newbie in embedded system. I am appreciating your helping. Thank you a lot.

I think that I want to support t-kernel and other OS to U-boot-sh. I cooperate with you.

Best regards,
Nobuhiro

author
#2 lore raw
Quoted 3 lines

If you want make SREC file to Flash, you need to use objcopy command. shX-linux-objcopy -Ibinary -Osrec u-boot.bin u-boot.flash.srec

This is a good instruction, now I could flash the srec image to Flash Memory by this command.

srec file was created by below command cannot flash into board.

# sh3-linux-objcopy --gap-fill=0xff -O srec u-boot u-boot.srec
# sh3-linux-objcopy --gap-fill=0xff -O binary u-boot u-boot.bin

Here are file sizes
u-boot.flash.srec 213040
u-boot.srec 222322
u-boot.bin 74080

Quoted 1 line

Please check doc/README.sh.

I didn't see it. there is only doc/README.sha1

Quoted 4 lines

I think that you know it, T-engine has a monitor program. The T-engine user uses this monitor program and writes in it at a flash bulb.
However, as for this program, only a SREC file is usable.

This is a T-Monitor program can work as boot loader application. But I didn't use it for flashing memory ROM. I would like to use UBoot as a boot loader replacing this application (T-Monitor).

I worked with Downloader utility of Debug board (T-Engine/SH7727 DevKit)
====================================================

      T-Engine(MS7727CP01) DownLoader Ver1.8L

----------------------------------------------------
SH7727 Flash Memory Change Value!
Flash Memory data copy to RAM
Please Send A S-format Record

Start Addrs = 00000000
End Addrs = 0001215F

Transfer complete
Flash chip erase: complete
Program :complete
Flash write complete
Ready>RESTART

I have questions about uboot below:
1. Reallocating address of u-boot in booting process.
At the booting process, the address 0x80000000 is executed. This is memory mapping address of Flash memory. and executable code of T-Monitor will be executed.

(1) ROM area memory map
In ROM, 8M byte(0x80000000-0x807FFFFF)of area is implemented. Memory map of ROM area is shown as below.

     0x80000000 +-------------------------------+
                |      T-Monitor code           |
                |- - - - - - - - - - - - - - - -|
                |                               |
     0x80010000 +-------------------------------+
                |        ROM Information        |
     0x80010080 +-------------------------------+
                |System configuration info      |
                |     (SYSCONF / DEVCONF)       |
                |- - - - - - - - - - - - - - - -|
                |                               |
     0x80020000 +-------------------------------+
                |       T-Kernel code           |
                |                               |
                +-------------------------------+
                |                               |
                |         User area             |
                |                               |
     0x80800000 +-------------------------------+

UBoot code will reflash into Flash memory at 0x80000000 address. This is Flash Memory just readonly. Will UBoot reallocating (loading) binary code into SDRAM at TEXT_BASE address. In T-Engine/Sh7727, this address will be 0x8DFC0000 (Beginning address of SDRAM is 0x8C000000). Does UBoot automatically reload this code into TEXT_BASE address?

Because Boot starting address will begin at Flash memory (0x80000000) and T-Monitor (current boot loader) worked at this address. I don't know how about UBoot. Does it reload Uboot into SDRAM (TEXT BASE) and run?

2. This is a great site for working SH with Linux.
http://www.superh-linux.org/platforms/index.html
Based on Reference board board/ms7720se, I changed the UBoot configuration for T-Engine/SH7727 MS7727CP02 Kit.

Many thanks to authors for your efforts
# Nobuhiro Iwamatsu <[email protected]> # Yoshihiro Shimoda <[email protected]>

I got a toolchain at
http://www.superh-linux.org/archive/bsp/sh7721_se/toolchain_sh3_gcc4.2.tar.gz
It supported "elf32-sh-linux" target.
And I also got toolchain from T-Engine forum and it support "elf32-sh-tkernel" target.

I don't know UBoot built with toolchain from http://www.superh-linux.org can work on T-Engine platform or not?

3. Debugging tool for U-Boot development.
Please tell me how to debug UBoot can work on board. Could you tell me debugger tool for this purpose? Now I can reflash UBoot into Flash Memory but I don't know how to check UBoot can work on it. Because porting have others issues such as serial library, interrupt....

Could you recommend a tool can check it can work?
Sorry for stupid question.

4. Serial driver for UBoot on T-Engine/SH7727 board.
After make sure these configuration are correct setting (SDRAM adress, Flash Memory). Next step is serial porting for UBoot.

I think serial is basic peripheral and It can work with a small changes. But Maybe I am wrong. Could you recommend the steps I could work on for serial porting of UBoot?

T-Engine has a serial library. I don't know how can reuse this library or not? :(

Quoted 2 lines

I think that I want to support t-kernel and other OS to U-boot-sh. I cooperate with you.

Nice for hearing that. I appreciated your help. Many thanks for your effort.

Best regards,
Thao

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p18887349.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#3 lore raw

Hello,

2008/8/8 thaoth <[email protected]>:

Quoted 31 lines

I have questions about uboot below:
1. Reallocating address of u-boot in booting process.
At the booting process, the address 0x80000000 is executed. This is memory mapping address of Flash memory. and executable code of T-Monitor will be executed.

(1) ROM area memory map
In ROM, 8M byte(0x80000000-0x807FFFFF)of area is implemented. Memory map of ROM area is shown as below.

    0x80000000 +-------------------------------+
               |      T-Monitor code           |
               |- - - - - - - - - - - - - - - -|
               |                               |
    0x80010000 +-------------------------------+
               |        ROM Information        |
    0x80010080 +-------------------------------+
               |System configuration info      |
               |     (SYSCONF / DEVCONF)       |
               |- - - - - - - - - - - - - - - -|
               |                               |
    0x80020000 +-------------------------------+
               |       T-Kernel code           |
               |                               |
               +-------------------------------+
               |                               |
               |         User area             |
               |                               |
    0x80800000 +-------------------------------+
Quoted 5 lines

UBoot code will reflash into Flash memory at 0x80000000 address. This is Flash Memory just readonly. Will UBoot reallocating (loading) binary code into SDRAM at TEXT_BASE address. In T-Engine/Sh7727, this address will be 0x8DFC0000 (Beginning address of SDRAM is 0x8C000000). Does UBoot automatically reload this code into TEXT_BASE address?

Yes, U-Boot designed working on SDRAM.
In cpu/sh3/start.S, code of U-boot is copied from a flash bulb by memory and jump in memory.
Because implementation of original U-boot comes to work as for this on memory, I match the SuperH with this implementation.

Quoted 14 lines

Because Boot starting address will begin at Flash memory (0x80000000) and T-Monitor (current boot loader) worked at this address. I don't know how about UBoot. Does it reload Uboot into SDRAM (TEXT BASE) and run?

2. This is a great site for working SH with Linux.
http://www.superh-linux.org/platforms/index.html
Based on Reference board board/ms7720se, I changed the UBoot configuration for T-Engine/SH7727 MS7727CP02 Kit.

Many thanks to authors for your efforts
# Nobuhiro Iwamatsu <[email protected]> # Yoshihiro Shimoda <[email protected]>

Quoted 8 lines

I got a toolchain at
http://www.superh-linux.org/archive/bsp/sh7721_se/toolchain_sh3_gcc4.2.tar.gz
It supported "elf32-sh-linux" target.
And I also got toolchain from T-Engine forum and it support "elf32-sh-tkernel" target.

I don't know UBoot built with toolchain from http://www.superh-linux.org can work on T-Engine platform or not?

Sorry , I dont know it.
The tool chain of http://www.superh-linux.org tests only elf32-sh-linux.

Quoted 9 lines

3. Debugging tool for U-Boot development.
Please tell me how to debug UBoot can work on board. Could you tell me debugger tool for this purpose? Now I can reflash UBoot into Flash Memory but I don't know how to check UBoot can work on it. Because porting have others issues such as serial library, interrupt....

Could you recommend a tool can check it can work?
Sorry for stupid question.

A developer has many cases to debug with ICE.
When there is not ICE, We write in it at SDRAM with monitor and debug it on SDRAM.

Quoted 5 lines

4. Serial driver for UBoot on T-Engine/SH7727 board.
After make sure these configuration are correct setting (SDRAM adress, Flash Memory). Next step is serial porting for UBoot.

Quoted 7 lines

I think serial is basic peripheral and It can work with a small changes. But Maybe I am wrong. Could you recommend the steps I could work on for serial porting of UBoot?

T-Engine has a serial library. I don't know how can reuse this library or not? :(

There is two approach.
1. You delete content of Flash, and it is the method that only U-Boot uses. When you use this method, you come to need ICE.
But this is very simple.

2. You call U-boot like an application from T-monitor, and to use. When you use this method, you will not need ICE.
But you need Implementation serial function used T-monitor's library.

I will ask a specialist in T-engine an opinion. I will send e-mail it if there is some information.

Many Japanese companies become the long vacation from tomorrow. Because I am a holiday, an answer is not possible for approximately 2 weeks.

Best regards,
Nobuhiro

Signature · 1 line
Nobuhiro Iwamatsu
author
#4 lore raw

Hi Nobuhiro Iwamatsu,

1. Clock frequency of board.

#define CONFIG_SYS_CLK_FREQ 33333333
#define TMU_CLK_DIVIDER 4 /* 4 (default), 16, 64, 256 or 1024 */
#define CFG_HZ (CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)

I don't understand how to set CONFIG_SYS_CLK_FREQ value. From T-Engine support, they said clock frequency of board is 144MHz.

CPU:       SH7727 144 MHz
Flash ROM: 80000000 - 807FFFFF : 8 MB (64 KB blk x 128)
           80000000 - 8000FFFF : Monitor Area (64 KB)
           80010000 - 8001007F : RomInfo Area (128 B)
SDRAM:     8C000000 - 8DFFFFFF : 32 MB
           8C000000 - 8C001FFF : Monitor & System Area (8 KB)

Could I set CFG_HZ to 144?
#define CFG_HZ 144

2. Cross compiler tool chain : GCC vs T-Engine toolchain
There are two tool chains
-
http://www.superh-linux.org/archive/bsp/sh7721_se/toolchain_sh3_gcc4.2.tar.gz
support elf32-sh-linux target.
- Tool chain from T-Engine forum support elf32-sh-tkernel Using both cross compilers, we could turn on LED on debug board by setting correct value LED_A and LED_B value.

3. ICE or JTAG debugger and LED debugging.
I don't have these debug tools, and so hard for debugging. T-Engine/SH7727 DevKit has debug board with 8 LEDs. I could turn on/off these LEDs by setting correct value to 0xA1600000 memory. But C function turn on/off LED cannot work. For example

int cpu_init(void)

{
        // Turn off LED 1 to notify cpu_init is called.
	outw(0x00 & 0xFF, 0xa1600000);
	return 0;
}

I don't know why it isn't called?

Would you please give me your ideas? Thank you a lot. Regards,

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19062634.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#5 lore raw

Hi,

2008/8/20 thaoth <[email protected]>:

Quoted 11 lines

Hi Nobuhiro Iwamatsu,

1. Clock frequency of board.

#define CONFIG_SYS_CLK_FREQ     33333333
#define TMU_CLK_DIVIDER         4       /* 4 (default), 16, 64, 256 or 1024 */
#define CFG_HZ                  (CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)

I don't understand how to set CONFIG_SYS_CLK_FREQ value. From T-Engine support, they said clock frequency of board is 144MHz.

Please set outside clock to CONFIG_SYS_CLK_FREQ.

Quoted 16 lines

2. Cross compiler tool chain : GCC vs T-Engine toolchain
There are two tool chains
-
http://www.superh-linux.org/archive/bsp/sh7721_se/toolchain_sh3_gcc4.2.tar.gz
support elf32-sh-linux target.
- Tool chain from T-Engine forum support elf32-sh-tkernel Using both cross compilers, we could turn on LED on debug board by setting correct value LED_A and LED_B value.

3. ICE or JTAG debugger and LED debugging.
I don't have these debug tools, and so hard for debugging. T-Engine/SH7727 DevKit has debug board with 8 LEDs. I could turn on/off these LEDs by setting correct value to 0xA1600000 memory. But C function turn on/off LED cannot work. For example

Quoted 8 lines

int cpu_init(void)

{
       // Turn off LED 1 to notify cpu_init is called.
       outw(0x00 & 0xFF, 0xa1600000);
       return 0;
}

I don't know why it isn't called?

I think that cpu_init is not carried out.
I think that u-boot stopped on lowlevel_init function.

Quoted 2 lines

Would you please give me your ideas? Thank you a lot.

I will get T-Engine board ......
Please wait.

Best regards,
Nobuhiro

author
#6 lore raw

Hi Nobuhiro Iwamatsu,

Quoted 1 line

Please set outside clock to CONFIG_SYS_CLK_FREQ.

Sorry I didn't see "outside clock" in T-Engine/SH7727 specification. Regard to clock of board, there are 3 types
- Internal clock
- Peripheral clock
- Bus clock

And have a look initialization values of T-Monitor - a boot loader of T-Engine/SH7727,
ICLK_VAL: .long 0x0060 // 96 Mhz
PCLK_VAL: .long 0x0018 // 24 Mhz
FRQCR_VAL: .long 0x0112 // PLL*2, IFC*1, PFC/4
RTCOR_VAL: .long 0xa50b // 48MHz /64 14.667us

FRQCR: frequency multipliers controller
RTCOR: reflash time constant counter

Does "outside clock" mean peripheral clock? It is 24 Mhz.

Quoted 2 lines

I think that cpu_init is not carried out.
I think that u-boot stopped on lowlevel_init function.

In lowlevel_init function, I put a LED debugging function which turn on LED on debug board. It works.

	mov.l	LED_A, r1
	mov.l	LED_D, r0
	mov.b	r0, @r1

LED_A: .long 0xA1600000 /* LED_BASE address */
LED_D: .long 0xaa /* mh a1600000, 00 --> ALL LED ON */

But C function in sh_generic_init() cannot work. :(

Quoted 1 line

I will get T-Engine board ......

Thank you and hope hearing good news from you.
Best regards,

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19083780.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
author
#7 lore raw

Hi Nobuhiro Iwamatsu,

Quoted 2 lines

I think that cpu_init is not carried out.
I think that u-boot stopped on lowlevel_init function.

Quoted 4 lines · thaoth

In lowlevel_init function, I put a LED debugging function which turn on LED on debug board. It works.

Quoted 9 lines
	mov.l	LED_A, r1
	mov.l	LED_D, r0
	mov.b	r0, @r1

LED_A: .long 0xA1600000 /* LED_BASE address */
LED_D: .long 0xaa /* mh a1600000, 00 --> ALL LED ON */

But C function in sh_generic_init() cannot work. :(

Here is lowlevel_init.S

Quoted 250 lines
	.global	lowlevel_init

	.text
	.align	2

lowlevel_init:

	mov.l	WTCSR,r1		// WTCSR: 0xFFFFFF86 Watchdog Timer Control / Status
Register)
	mov.l	WTCSR_D,r0		// WTCSR_D: 0xA506
	mov.w	r0, at r1

	mov.l	WTCNT,r1		// WTCNT: 0xFFFFFF84 Watchdog Timer Counter
	mov.l	WTCNT_D,r0		// WTCNT_D: 0x5A00
	mov.w	r0, at r1

! mov.l UCLKCR,r1 // UCLKCR: USBH/USBF Clock control register
! mov.l UCLKCR_D,r0
! mov.w r0, at r1

	mov.l	FRQCR, r1		// FRQCR_A: 0xFFFFFF80 Frequency control register
Address
	mov.l	FRQCR_VAL, r0
	mov.w	r0, @r1

	mov.l	BCR1, r1
	mov.l	BCR1_VAL, r0
	mov.w	r0, @r1			// base control register 1

	mov.l	BCR2, r1
	mov.l	BCR2_VAL, r0
	mov.w	r0, @r1			// base control register 2

	mov.l	WCR1, r1
	mov.l	WCR1_VAL, r0
	mov.w	r0, @r1			// wait state control register 1

	mov.l	WCR2, r1
	mov.l	WCR2_VAL, r0
	mov.w	r0, @r1			// wait state control register 2

	mov.l	MCR, r1
	mov.l	MCR_VAL, r0
	mov.w	r0, @r1			// memory control register

	mov.l	PCR, r1
	mov.l	PCR_VAL, r0
	mov.w	r0, @r1			// PCMCIA control register

	mov.l	RTCSR, r1
	mov.w	RTCSR_DUMMY, r0
	mov.w	r0, @r1			// reflash timer control / status register

	mov.l	RTCNT, r1
	mov.w	RTCNT_VAL, r0
	mov.w	r0, @r1			// reflash timer counter

	mov.l	RTCOR, r1
	mov.w	RTCOR_VAL, r0
	mov.w	r0, @r1			// reflash time constant counter

	mov.l	RFCR, r1
	mov.w	RFCR_VAL, r0
	mov.w	r0, @r1			// reflash count register

	/* SDRAM initalization */
	// 100us dummy wait

	mov.l	SDMR3_ADDR, r1
	mov.w	SDMR3_VAL, r0
	mov.w	r0, @r1			// reflash count register

	mov.l	RTCSR, r1
	mov.w	RTCSR_VAL, r0
	mov.w	r0, @r1			// reflash timer control / status register

	// dummy reflash
	/***********************/

// mov.l _PINTER, r1 // init PINTER
// mov #0, r0
// mov.w r0, @r1

// mov.l _IPRA, r1 // init IPRA
// mov.w IPRA_VAL, r0
// mov.w r0, @r1

// mov.l _IPRD, r1 // init IPRD
// mov.w IPRD_VAL, r0
// mov.w r0, @r1

// mov.l _IPRG, r1 // init IPRG
// mov.w IPRG_VAL, r0
// mov.w r0, @r1

// mov.l _ICR1, r1 // init ICR1
// mov.w ICR1_VAL, r0
// mov.w r0, @r1

// mov.l _ICR2, r1 // init ICR2
// mov.w ICR2_VAL, r0
// mov.w r0, @r1

// mov.l _PINTER, r1 // init PINTER
// mov.w PINTER_VAL, r0
// mov.w r0, @r1

	mov.l	PCCR, r1		// init PCCR
	mov.w	PCCR_VAL, r0
	mov.w	r0, @r1

	mov.l	PDCR, r1		// init PDCR
	mov.w	PDCR_VAL, r0
	mov.w	r0, @r1

	mov.l	PECR, r1		// init PECR
	mov.w	PECR_VAL, r0
	mov.w	r0, @r1

	mov.l	PHCR, r1		// init PHCR
	mov.w	PHCR_VAL, r0
	mov.w	r0, @r1

	mov.l	PJCR, r1		// init PJCR
	mov.w	PJCR_VAL, r0
	mov.w	r0, @r1

	mov.l	PKCR, r1		// init PKCR
	mov.w	PKCR_VAL, r0
	mov.w	r0, @r1

	mov.l	PLCR, r1		// init PLCR
	mov.w	PLCR_VAL, r0
	mov.w	r0, @r1

	mov.l	PMCR, r1		// init PMCR
	mov.w	PMCR_VAL, r0
	mov.w	r0, @r1

	mov.l	SCPCR, r1		// init SCPCR
	mov.w	SCPCR_VAL, r0
	mov.w	r0, @r1

! mov.l ICLK, r1 // init internal clock 96 Mhz
! mov.l ICLK_VAL, r0
! mov.w r0, @r1

! mov.l PCLK, r1 // init peripheral clock 24 Mhz
! mov.l PCLK_VAL, r0
! mov.w r0, @r1

	mov.l	LED_A, r1
	mov.l	LED_D, r0
	mov.b	r0, @r1
	
	rts
	nop

	.align 4

!ICLK: .long 0x8c000274
!PCLK: .long 0x8c000276

WTCSR: .long 0xFFFFFF86 /* WTCSR: 0xFFFFFF86 Watchdog Timer Control /
Status Register) */
WTCNT: .long 0xFFFFFF84 /* WTCNT: 0xFFFFFF84 Watchdog Timer Counter */
/*UCLKCR: .long 0xA40A0008*/ /* USBH/USBF: Clock control register ???*/
FRQCR: .long 0xffffff80

BCR1:		.long	0xffffff60      /* Bus Control Register 1 */
BCR2:		.long	0xffffff62      /* Bus Control Register 2 */
WCR1:		.long	0xffffff64      /* Wait State Control Register 1 */
WCR2:		.long	0xffffff66      /* Wait State Control Register 2 */
MCR:		.long	0xffffff68      /* Individual Memory Control Register */
PCR:		.long	0xffffff6c      /* PCMCIA control register */
RTCSR:		.long	0xffffff6e      /* Refresh timer control/status register */
RTCNT:		.long	0xffffff70      /* Refresh timer counter */
RTCOR:		.long	0xffffff72      /* Refresh time contant register */

RFCR: .long 0xffffff74 /* Refresh count register */
SDMR3_ADDR: .long 0xFFFFE800 + 0x80 /* Synchorounos DRAM Mode register
??? */

/* SH Internal Use - Area 1 */
PCCR: .long 0xa4000104
PDCR: .long 0xa4000106
PECR: .long 0xa4000108
PFCR: .long 0xa400010a
PGCR: .long 0xa400010c
PHCR: .long 0xa400010e
PJCR: .long 0xa4000110
PKCR: .long 0xa4000112
PLCR: .long 0xa4000114
PMCR: .long 0xa4000118
SCPCR: .long 0x04000116

/* Initialize data */
ICLK_VAL: .long 0x0060 // 96 Mhz
PCLK_VAL: .long 0x0018 // 24 Mhz

WTCNT_D: .long 0x5A00 /* WTCNT_D: 0x5A00 set the upper byte to 5A and
transfer data into lower byte */
WTCSR_D: .long 0xA506 /* WTCSR_D: 0xA506 set the upper byte to A5 and
transfer data into lower byte */
/*UCLKCR_D: .long 0xA5C0*/

FRQCR_VAL: .long 0x0112 // PLL*2, IFC*1, PFC/4
BCR1_VAL: .long 0x0008 /* Bus Control Register 1 */
BCR2_VAL: .long 0x2ae0 /* Bus Control Register 2 */
#if USE_R0P7727TH003TRK == 1
WCR1_VAL: .long 0xaaa2 /* Wait State Control Register 1 */
#else // previous type T-Engine
WCR1_VAL: .long 0xaa22
#endif
WCR2_VAL: .long 0xb6dd /* Wait State Control Register 2 */

#if USE_R0P7727TH003TRK == 1
MCR_VAL: .long 0x966c /* Individual Memory Control Register */
#else // previous type T-Engine
MCR_VAL: .long 0x012c
#endif
PCR_VAL: .long 0x0000 /* PCMCIA control register */
RTCSR_DUMMY: .long 0xa500 //
RTCSR_VAL: .long 0xa518 /* Refresh timer control/status register : CKIO
1/64 */
RTCNT_VAL: .long 0xa500 /* Refresh timer counter */

#if USE_R0P7727TH003TRK == 1
RTCOR_VAL: .long 0xa505 /* Refresh time contant register */
#else // previous type T-Engine
RTCOR_VAL: .long 0xa50b // 48MHz /64 14.667us
#endif
RFCR_VAL: .long 0xa400 /* Refresh count register */
SDMR3_VAL: .long 0x00 /* Synchorounos DRAM Mode register ??? */

IPRA_VAL: .long 0x8000
IPRD_VAL: .long 0xc000
IPRG_VAL: .long 0xc000
ICR1_VAL: .long 0x42aa
ICR2_VAL: .long 0x000c
PINTER_VAL: .long 0x000c
PCCR_VAL: .long 0x0000
PDCR_VAL: .long 0x0000
PECR_VAL: .long 0x0500
PFCR_VAL: .long 0x00AA
PGCR_VAL: .long 0xA200
PHCR_VAL: .long 0x0800
PJCR_VAL: .long 0x0540
PKCR_VAL: .long 0x0005
PLCR_VAL: .long 0xaaaa
PMCR_VAL: .long 0xaa00
SCPCR_VAL: .long 0x0000

Quoted 6 lines

SDCR_D1: .long 0x00000011
SDCR_D2: .long 0x00000811

LED_A: .long 0xA1600000 /* LED_BASE address */
LED_D: .long 0xaa /* mh a1600000, 00 --> ALL LED ON */

void sh_generic_init (void)
{
...

	outw(0x7e, LED_BASE);
}

Now sh_generic_init could be called with LEDs indicated true status. :-) But I don't know what next issue? :-((

Best regards,

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19085658.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
author
#8 lore raw

Hi Nobuhiro Iwamatsu,

I have checked sequence initialization functions in sh_generic_init and the problem is serial library cannot work correctly. The result is output to console cannot display.

Regards.

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19086799.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
author
#9 lore raw
In reply to Nobuhiro Iwamatsu

Hi Nobuhiro Iwamatsu,
Now I'm porting USB on board T-Engine(SH7727)
- My configure following :
#define CONFIG_CMD_USB
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_USB_STORAGE 1
#define CFG_USB_OHCI_REGS_BASE 0x04000400
#define CFG_USB_OHCI_SLOT_NAME "s3c2400"
#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_DOS_PARTITION 1
#define CONFIG_SYS_CLK_FREQ 33333333
#define TMU_CLK_DIVIDER 4 /* 4 (default), 16, 64, 256 or 1024 */
#define CFG_HZ (CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)
- And in lowlevel_init.S, I change USB clock following:
UCLKCR_A: .long 0xA40A0008
UCLKCR_D: .long 0xA5C0
mov.l UCLKCR_A,r1
mov.l UCLKCR_D,r0
mov.w r0, at r1
- When I'm starting board with above configue, I see the led of USB device is blinking. Then I run command "usb start", the led turn off and u-boot don't find any USB device, with following logs:
DEBUG: OHCI controller usb-s3c2400 state
DEBUG: control: 0x0000008f HCFS=operational IE PLE CBSR=3
DEBUG: cmdstatus: 0x00000000 SOC=0
DEBUG: intrstatus: 0x00000004 SF
DEBUG: intrenable: 0x00000053 RHSC UE WDH SO
DEBUG: hcca frame #0019
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000100 PPS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
scanning bus for devices... New Device 0
usb_control_msg: request: 0x6, requesttype: 0x80
value 0x100 index 0x0 length 0x8
INFO: submit_control_msg
DEBUG: SUB URB:[ 42] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000
DEBUG: SUB(rh) URB:[ 45] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000
INFO: Root-Hub: adr: 0 cmd(8): 00000680 0001 0000 0800
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000100 PPS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ 56] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x2 usb_ohci.c: cmd(8): 80 06 01 00 00 00 00 08
usb_ohci.c: data(0/8):
USB device not responding, giving up (status=2)
0 USB Device(s) found scanning bus for storage devices... 0 Storage
Device
(s) found
- I don't know what is wrong in my configure, I think the CONFIG_SYS_CLK_FREQ and CFG_HZ is incorrect and I can't start USB device, and clock which I control in lowlevel_init.S following:
FRQCR_A: .long 0xA415FF80 /* FRQCR Address(Frequency Control Register) */
FRQCR_D: .long 0x1103 /* I:B:P=8:4:2 */
Can you help me about this problem and tell me about any other wrong things in my configure? why the led turn off when I run command "usb start"?

thanks

Quoted 65 lines · Nobuhiro Iwamatsu

Hi,

2008/8/20 thaoth <[email protected]>:

Quoted 5 lines

Hi Nobuhiro Iwamatsu,

1. Clock frequency of board.

Quoted 7 lines

#define CONFIG_SYS_CLK_FREQ 33333333
#define TMU_CLK_DIVIDER 4 /* 4 (default), 16, 64, 256 or
1024 */
#define CFG_HZ (CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)

I don't understand how to set CONFIG_SYS_CLK_FREQ value. From T-Engine support, they said clock frequency of board is 144MHz.

Please set outside clock to CONFIG_SYS_CLK_FREQ.

Quoted 19 lines

2. Cross compiler tool chain : GCC vs T-Engine toolchain There are two tool chains
-
http://www.superh-linux.org/archive/bsp/sh7721_se/toolchain_sh3_gcc4.2.tar.gz
support elf32-sh-linux target.
- Tool chain from T-Engine forum support elf32-sh-tkernel Using both cross compilers, we could turn on LED on debug board by setting
correct value LED_A and LED_B value.

3. ICE or JTAG debugger and LED debugging.
I don't have these debug tools, and so hard for debugging. T-Engine/SH7727
DevKit has debug board with 8 LEDs. I could turn on/off these LEDs by setting correct value to 0xA1600000 memory. But C function turn on/off LED
cannot work. For example

Quoted 8 lines

int cpu_init(void)

{
       // Turn off LED 1 to notify cpu_init is called.
       outw(0x00 & 0xFF, 0xa1600000);
       return 0;
}

I don't know why it isn't called?

I think that cpu_init is not carried out.
I think that u-boot stopped on lowlevel_init function.

Quoted 2 lines

Would you please give me your ideas? Thank you a lot.

I will get T-Engine board ......
Please wait.

Best regards,
Nobuhiro
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19282461.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
author
#10 lore raw
In reply to Nobuhiro Iwamatsu

Hi,

I got USB issue and here is an error message:

ERROR: CTL:TIMEOUT
USB device not responding, giving up (status=20) 3 USB Device(s) found
scanning bus for storage devices...
0 Storage Device(s) found

For detail, TEngine/SH7727 has one USB host controller, when I plugged USB Flash Memory there were 3 devices. And No unplugged USB device, they said 2 devices.

=> usb info
1: Hub, USB Revision 1.10
- OHCI Root Hub
- Class: Hub
- PacketSize: 8 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 0.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms

Configuration: 0
- Interfaces: 0 Bus Powered 0mA

Configuration: 0
- Interfaces: 0 Bus Powered 0mA

The problem sounded USB host controller driver could work well but submit_common_msg couldn't get description of USB flash memory device and it said "No storage device".

Here is configuration of USB on UBoot

/* USB Mass Storage Support*/
#define CONFIG_CMD_USB
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_USB_STORAGE 1

#define CFG_USB_OHCI_REGS_BASE 0xA4000400
#define CFG_USB_OHCI_SLOT_NAME "s3c2400"
#define CFG_USB_OHCI_MAX_ROOT_PORTS 15

Could I have help? Please tell me if you have any idea. Thank you for your helping. =)

Here is a log data

U-Boot 1.3.4-00404-gab00e7a-dirty (Sep 10 2008 - 16:30:38)

CPU: SH3
BOARD: Hitachi UL MS7727SE
DRAM: 32MB
FLASH: 8MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
=> usb start
(Re)start USB...
USB:   INFO: aligned ghcca 8e01ad00
DEBUG: hc_reset

DEBUG: USB HC reset_hc usb-s3c2400: ctrl = 0x0 ;

DEBUG: OHCI controller usb-s3c2400 state
DEBUG: control: 0x0000008f HCFS=operational IE PLE CBSR=3
DEBUG: cmdstatus: 0x00000000 SOC=0
DEBUG: intrstatus: 0x00000004 SF
DEBUG: intrenable: 0x00000053 RHSC UE WDH SO
DEBUG: hcca frame #000d
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000100 PPS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS scanning bus for devices... New Device 0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0
x8
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000
INFO: Root-Hub: adr: 0 cmd(8): 00000680 0100 0000 0008
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000100 PPS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x0
usb_ohci.c: cmd(8): 80 06 00 01 00 00 08 00
usb_ohci.c: data(0/8):
set address 1
usb_control_msg: request: 0x5, requesttype: 0x0, value 0x1 index 0x0 length 0x0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 00 05 01 00 00 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 00 05 01 00 00 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000500 0001 0000 0000
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 00 05 01 00 00 00 00 00
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0
x12
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/18 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/18 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 00000680 0100 0000 0012
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/18 stat:0x0
usb_ohci.c: cmd(8): 80 06 00 01 00 00 12 00
usb_ohci.c: data(0/18):
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0
x8
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 00000680 0200 0000 0008
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/8 stat:0x0
usb_ohci.c: cmd(8): 80 06 00 02 00 00 08 00
usb_ohci.c: data(0/8):
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0
x19
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/25 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/25 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 00000680 0200 0000 0019
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/25 stat:0x0
usb_ohci.c: cmd(8): 80 06 00 02 00 00 19 00
usb_ohci.c: data(0/25):
get_conf_no 0 Result 25, wLength 25
if 0, ep 0
##EP epmaxpacketin[1] = 2
set configuration 1
usb_control_msg: request: 0x9, requesttype: 0x0, value 0x1 index 0x0 length 0x0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 00 09 01 00 00 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 00 09 01 00 00 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000900 0001 0000 0000
INFO: WR:status 0x10000
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 00 09 01 00 00 00 00 00
new device strings: Mfr=0, Product=1, SerialNumber=0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x300 index 0x0 length 0
xFF
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 00000680 0300 0000 00ff
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x0
usb_ohci.c: cmd(8): 80 06 00 03 00 00 ff 00
usb_ohci.c: data(0/255):
USB device number 1 default language ID 0x409
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x301 index 0x409 length
0xFF
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 00000680 0301 0409 00ff
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x0
usb_ohci.c: cmd(8): 80 06 01 03 09 04 ff 00
usb_ohci.c: data(0/255):
Manufacturer
Product OHCI Root Hub
SerialNumber
USB hub found
usb_control_msg: request: 0x6, requesttype: 0xA0, value 0x2900 index 0x0 length
0x4
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000006a0 2900 0000 0004
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x0
usb_ohci.c: cmd(8): a0 06 00 29 00 00 04 00
usb_ohci.c: data(0/4):
usb_control_msg: request: 0x6, requesttype: 0xA0, value 0x2900 index 0x0 length
0x9
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/9 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/9 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000006a0 2900 0000 0009
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/9 stat:0x0
usb_ohci.c: cmd(8): a0 06 00 29 00 00 09 00
usb_ohci.c: data(0/9):
2 ports detected
ganged power switching
standalone hub
no over-current protection
power on to power good time: 4ms
hub controller current requirement: 0mA
port 1 is removable
port 2 is removable
usb_control_msg: request: 0x0, requesttype: 0xA0, value 0x0 index 0x0 length 0x4
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000000a0 0000 0000 0004
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x0
usb_ohci.c: cmd(8): a0 00 00 00 00 00 04 00
usb_ohci.c: data(0/4):
get_hub_status returned status 0, change 0
local power source is good
no over-current condition exists
enabling power on all ports
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x8 index 0x1 length 0x0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 03 08 00 01 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 03 08 00 01 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000323 0008 0001 0000
INFO: WR:portstatus[0] 0x100
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 03 08 00 01 00 00 00
port 1 returns 0
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x8 index 0x2 length 0x0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 03 08 00 02 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 03 08 00 02 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000323 0008 0002 0000
INFO: WR:portstatus[1] 0x100
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 03 08 00 02 00 00 00
port 2 returns 0
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x0
usb_ohci.c: cmd(8): a3 00 00 00 01 00 04 00
usb_ohci.c: data(0/4):
Port 1 Status 101 Change 1
port 1 connection change
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x0
usb_ohci.c: cmd(8): a3 00 00 00 01 00 04 00
usb_ohci.c: data(0/4):
portstatus 101, change 1, High Speed
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x10 index 0x1 length 0x
0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 10 00 01 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 10 00 01 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000123 0010 0001 0000
INFO: WR:portstatus[0] 0x10000
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000101 PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 01 10 00 01 00 00 00
hub_port_reset: resetting port 0...
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x4 index 0x1 length 0x0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 03 04 00 01 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 03 04 00 01 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000323 0004 0001 0000
INFO: WR:portstatus[0] 0x10
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000311 LSDA PPS PRS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 03 04 00 01 00 00 00
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x0
usb_ohci.c: cmd(8): a3 00 00 00 01 00 04 00
usb_ohci.c: data(0/4):
portstatus 303, change 10, Low Speed
STAT_C_CONNECTION = 0 STAT_CONNECTION = 1 USB_PORT_STAT_ENABLE 1
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x14 index 0x1 length 0x
0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 14 00 01 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 14 00 01 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000123 0014 0001 0000
INFO: WR:portstatus[0] 0x100000
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000303 LSDA PPS PES CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 01 14 00 01 00 00 00
New Device 1
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0
x8
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000
DEBUG: SUB URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000
hc_interrupt regs->intrstatus=68;regs->intrenable=83;ints=64 submit_common_msg hc_interrupt():stat = 255
DEBUG: %
hc_interrupt regs->intrstatus=6;regs->intrenable=83;ints=2 submit_common_msg hc_interrupt():stat = 0
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
ERROR: CTL:TIMEOUT
DEBUG: submit_common_msg: TO status ff

DEBUG: RET(ctlr) URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x20

USB device not responding, giving up (status=20)
hub: disabling port 1
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x1 index 0x1 length 0x0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 01 00 01 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 01 00 01 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000123 0001 0001 0000
INFO: WR:portstatus[0] 0x1
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000301 LSDA PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 01 01 00 01 00 00 00
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x2 length 0x4
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0002 0004
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000301 LSDA PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x0
usb_ohci.c: cmd(8): a3 00 00 00 02 00 04 00
usb_ohci.c: data(0/4):
Port 2 Status 101 Change 1
port 2 connection change
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x2 length 0x4
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0002 0004
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000301 LSDA PPS CCS
DEBUG: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x0
usb_ohci.c: cmd(8): a3 00 00 00 02 00 04 00
usb_ohci.c: data(0/4):
portstatus 101, change 1, High Speed
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x10 index 0x2 length 0x
0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 10 00 02 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 10 00 02 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000123 0010 0002 0000
INFO: WR:portstatus[1] 0x10000
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000301 LSDA PPS CCS
DEBUG: roothub.portstatus [1] = 0x00000101 PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 01 10 00 02 00 00 00
hub_port_reset: resetting port 1...
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x4 index 0x2 length 0x0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 03 04 00 02 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 03 04 00 02 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000323 0004 0002 0000
INFO: WR:portstatus[1] 0x10
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000301 LSDA PPS CCS
DEBUG: roothub.portstatus [1] = 0x00000111 PPS PRS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 03 04 00 02 00 00 00
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x2 length 0x4
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000
INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0002 0004
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000301 LSDA PPS CCS
DEBUG: roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x0
usb_ohci.c: cmd(8): a3 00 00 00 02 00 04 00
usb_ohci.c: data(0/4):
portstatus 103, change 10, High Speed
STAT_C_CONNECTION = 0 STAT_CONNECTION = 1 USB_PORT_STAT_ENABLE 1
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x14 index 0x2 length 0x
0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 14 00 02 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 14 00 02 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000123 0014 0002 0000
INFO: WR:portstatus[1] 0x100000
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000301 LSDA PPS CCS
DEBUG: roothub.portstatus [1] = 0x00000103 PPS PES CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 01 14 00 02 00 00 00
New Device 2
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0
x8
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000
DEBUG: SUB URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000
hc_interrupt regs->intrstatus=68;regs->intrenable=83;ints=64 submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
DEBUG: %
DEBUG: hc_interrupt: returning..

submit_common_msg hc_interrupt():stat = 255
ERROR: CTL:TIMEOUT
DEBUG: submit_common_msg: TO status ff

DEBUG: RET(ctlr) URB:[ d] dev: 0,ep: 0-I,type:CTRL,len:0/8 stat:0x20

USB device not responding, giving up (status=20)
hub: disabling port 2
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x1 index 0x2 length 0x0
INFO: submit_control_msg
DEBUG: SUB URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 01 00 02 00 00 00

DEBUG: SUB(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000
usb_ohci.c: cmd(8): 23 01 01 00 02 00 00 00
INFO: Root-Hub: adr: 1 cmd(8): 00000123 0001 0002 0000
INFO: WR:portstatus[1] 0x1
DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2
DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000
DEBUG: roothub.status: 00000000
DEBUG: roothub.portstatus [0] = 0x00000301 LSDA PPS CCS
DEBUG: roothub.portstatus [1] = 0x00000101 PPS CCS
DEBUG: RET(rh) URB:[ d] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0
usb_ohci.c: cmd(8): 23 01 01 00 02 00 00 00
3 USB Device(s) found
scanning bus for storage devices... Storage Device(s) found

Thank you a lot.
Best regards,

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19411908.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#11 lore raw

Hi, thaoth.

Shimoda-san is USB developper on U-Boot in Renesas.

Shimoda-san, please give us comments this problem.

Best regards,
Nobuhiro

Quoted 14 lines · On Wed, 10 Sep 2008 04:51:40 -0700 (PDT) thaoth <[email protected]> wrote:

Hi,

I got USB issue and here is an error message:

ERROR: CTL:TIMEOUT
USB device not responding, giving up (status=20)
3 USB Device(s) found
scanning bus for storage devices...
0 Storage Device(s) found

For detail, TEngine/SH7727 has one USB host controller, when I plugged USB Flash Memory there were 3 devices. And No unplugged USB device, they said 2 devices.

Signature · 1 line
Nobuhiro Iwamatsu
#12 lore raw

Hi, thaoth.

I think that your board cannot communicate with USB device at all. SH7727 has EXCPGCR register. Do you set this register? When I used this CPU before, I did the following setting.

	STCBR3 = 0x18;
	SRSTR = 0x18;
	wait_10msec();

	EXCPGCR = 0x28;
	wait_10msec();

	SRSTR = 0x00;
	STCBR3 = 0x00;

Best regards,
Yoshihiro Shimoda

Quoted 27 lines · Nobuhiro Iwamatsu

Hi, thaoth.

Shimoda-san is USB developper on U-Boot in Renesas.

Shimoda-san, please give us comments this problem.

Best regards,
Nobuhiro

Quoted 13 lines · On Wed, 10 Sep 2008 04:51:40 -0700 (PDT) thaoth <[email protected]> wrote:

Hi,

I got USB issue and here is an error message:

ERROR: CTL:TIMEOUT
USB device not responding, giving up (status=20)
3 USB Device(s) found
scanning bus for storage devices...
0 Storage Device(s) found

For detail, TEngine/SH7727 has one USB host controller, when I plugged USB Flash Memory there were 3 devices. And No unplugged USB device, they said 2 devices.

author
#13 lore raw
Quoted 7 lines · Yoshihiro Shimoda

Hi, thaoth.

I think that your board cannot communicate with USB device at all. SH7727 has EXCPGCR register. Do you set this register? When I used this CPU before, I did the following setting.

Quoted 10 lines
	STCBR3 = 0x18;
	SRSTR = 0x18;
	wait_10msec();

	EXCPGCR = 0x28;
	wait_10msec();

	SRSTR = 0x00;
	STCBR3 = 0x00;

Thank you very much,

Following your instruction, I did
int usb_board_init(void)

{
    printf("usb_board_init\n");

    outw(0x18, STBCR3);
    outw(0x18, SRSTR);
    udelay(10);

    outw(0x28, EXCPGCR);
    udelay(10);
	
    outw(0x00, STBCR3);
    outw(0x00, SRSTR);
    return 0;
}
Quoted 2 lines

STCBR3 = 0x18;

I couldn't see this register "STCBR3 ", I only saw STBCR3. Is it correct?

But UBoot didn't work, Would you please tell me more detail ? Thank you alot :)

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19429512.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#14 lore raw

Hi, thaoth.

Quoted 8 lines · thaoth
Quoted 5 lines · Yoshihiro Shimoda

Hi, thaoth.

I think that your board cannot communicate with USB device at all. SH7727 has EXCPGCR register. Do you set this register? When I used this CPU before, I did the following setting.

< snip >

Quoted 2 lines
Quoted 1 line

Thank you very much,

You are welcome :)

Quoted 17 lines

Following your instruction, I did
int usb_board_init(void)

{
    printf("usb_board_init\n");

    outw(0x18, STBCR3);
    outw(0x18, SRSTR);
    udelay(10);

    outw(0x28, EXCPGCR);
    udelay(10);
	
    outw(0x00, STBCR3);
    outw(0x00, SRSTR);
    return 0;
}

These registers are 8-bit width. So please use outb() macro.

Quoted 4 lines
Quoted 3 lines

STCBR3 = 0x18;

I couldn't see this register "STCBR3 ", I only saw STBCR3. Is it correct?

Oh, I am sorry. That's correct.

Quoted 2 lines

But UBoot didn't work, Would you please tell me more detail ? Thank you alot :)

I am sorry, my explanation was short. This EXCPGCR value was for an another board. In the case of your board, it may be necessary to make it a defferent value. And I used my board, I set 0x1500 in PKCR.

Best regards,
Yoshihiro Shimoda

author
#15 lore raw

Hi,

Quoted 19 lines

Following your instruction, I did
int usb_board_init(void)

{
    printf("usb_board_init\n");

    outw(0x18, STBCR3);
    outw(0x18, SRSTR);
    udelay(10);

    outw(0x28, EXCPGCR);
    udelay(10);
	
    outw(0x00, STBCR3);
    outw(0x00, SRSTR);
    return 0;
}
Quoted 1 line

These registers are 8-bit width. So please use outb() macro.

They are the same. It is still problem.

Quoted 4 lines

I am sorry, my explanation was short. This EXCPGCR value was for an another board.
In the case of your board, it may be necessary to make it a defferent value.

As specification of SH7727, value of EXCPGCR is 0x28 and this means

""
The SH7727 has an on-chip USB interface (USB) which requires a fixed 48-MHz clock source.

The extend clock pulse generator (EXCPG) generates a divided clock from the internal clock (I?),
the bus clock (B?), or the external clock (UCLK).

Because the clock sources, which can be a candidate to be used by EXCPG, vary from CPG
setting or external clock source, user of SH7727 must adjust the divided clock, carefully to be 48
MHz.
""
* Bits 5 to 3?Clock Select (USBCKSEL2 to USBCKSEL0):
000: Peripheral Clock (P?) (Initial value)
100: Internal Clock (I?)
101: Bus Clock (B?)
110: External clock (UCLK)
***: Another value Reserved (setting prohibited)

* Bits 2 to 0?: Divider Select (USBDIVSEL2 to USBDIVSEL0):
000: 1/1 -> Dividing Ratio Selection
001: 1/2
010: 1/3
1**: Internal clock (I?), bus clock (B?), external clock (UCLK) halted

0x28: 00101000 -> 00 101 000 ->
* 101: Using bus clock
* 000: Dividing Ratio Selection is 1/1

I know
* Internal clock: 96Mhz
* Peripheral Clock: 24Mhz
* CPU Block: 144Mhz

http://www.nabble.com/file/p19449833/a.JPG a.JPG

Please let me know the correct value of EXCPGCR ? Is 0x28 correct initialize value of USB clock?

Quoted 1 line

And I used my board, I set 0x1500 in PKCR.

I don't understand PKCR - Port control register so I don't know correct initialize value of this register.

0x1500 = 0001 0101 0000 0000
-> PK6 is port output
-> PK5 is port output
-> PK4 is port output
I don't know this value could be set for my board - TEngine/SH7727.

I am appreciating your helping :)

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19449833.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#16 lore raw

Hi, thaoth.

Quoted 10 lines · thaoth

0x28: 00101000 -> 00 101 000 ->
* 101: Using bus clock
* 000: Dividing Ratio Selection is 1/1

I know
* Internal clock: 96Mhz
* Peripheral Clock: 24Mhz
* CPU Block: 144Mhz

Quoted 4 lines

http://www.nabble.com/file/p19449833/a.JPG a.JPG

Please let me know the correct value of EXCPGCR ? Is 0x28 correct initialize value of USB clock?

I think that 0x21 is correct value of EXCPGCR for your board.

0x21: 00101000 -> 00 100 001 ->
* 100: Using Internal Clock
* 001: Dividing Ratio Selection is 1/2
(96MHz / 2 = 48MHz)

Quoted 9 lines
Quoted 1 line

And I used my board, I set 0x1500 in PKCR.

I don't understand PKCR - Port control register so I don't know correct initialize value of this register.

0x1500 = 0001 0101 0000 0000
-> PK6 is port output
-> PK5 is port output
-> PK4 is port output
I don't know this value could be set for my board - TEngine/SH7727.

Oh, I am very sorry. This is PECR.
This setting enable USB1_pwr_en and USB2_pwr_en pin.

Best regards,
Yoshihiro Shimoda

author
#17 lore raw

Hi Yoshihiro Shimoda,
* Strategy 1:
I add usb_cpu_init following your tutorial:
int usb_cpu_init(void)

{	
	*STCBR3 = 0x18;
	*SRSTR = 0x18;		
	cpu_wait_ms(50);
	*EXCPGCR = 0x21;//0x28;
	*PECR = 0x1500;
	cpu_wait_ms(50);		
	*SRSTR = 0x00;
	*STCBR3 = 0x00;
	
	return 0;
}

now, I plug the USB2.0(mass storage) into board T-Engine(sh7727) and run command "usb start", the u-boot can't get decription of usb device with the errror following:

New Device 1
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0
x8
set address 2
usb_control_msg: request: 0x5, requesttype: 0x0, value 0x2 index 0x0 length 0x0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0
x12
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0
x8
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0
x20
get_conf_no 0 Result 32, wLength 32
if 0, ep 0
if 0, ep 1
##EP epmaxpacketin[1] = 64
* Strategy 2:
I add usb_cpu_init the same strategy 1, I only add instruction "printf("&ep = %x\n",&ep);" into function usb_set_maxpacket of usb.c
int usb_set_maxpacket(struct usb_device *dev)
{
.................................................
...................................................

			ep = &dev->config.if_desc[i].ep_desc[ii];
			b=ep->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK;			
			printf("&ep = %x\n",&ep);				

.....................................................
......................................................
}
in this strategy, when I run command "usb start", now I can get information of USB device:
Manufacturer
Product USB_DRIVE
SerialNumber 000000000000001000006886
2 USB Device(s) found

       scanning bus for storage devices... usb_control_msg: request: 0xFF,

reque
sttype: 0x21, value 0x0 index 0x0 length 0x0
usb_control_msg: request: 0x1, requesttype: 0x2, value 0x0 index 0x81 length 0x0
usb_control_msg: request: 0x1, requesttype: 0x2, value 0x0 index 0x2 length 0x0
1 Storage Device(s) found

I don't know what is problem?why when I add instruction "printf("&ep = %x\n",&ep);", u-boot can get description of USB device
*Strategy 3:
I try replace the insctruction "printf("&ep = %x\n",&ep);" with one of these instructions
- instruction 1: wait_ms(10)
- instruction 2:void * pointer = &ep;
- instruction 3: "printf("ep = %x\n",ep);"
But the result when run command "usb start" the same strategy 1, I can't get information of USB2.0(mass storage)

Can you help me to resolve this bug?
Thank you very much for your supports!

Quoted 48 lines · Yoshihiro Shimoda

Hi, thaoth.

Quoted 10 lines · thaoth

0x28: 00101000 -> 00 101 000 ->
* 101: Using bus clock
* 000: Dividing Ratio Selection is 1/1

I know
* Internal clock: 96Mhz
* Peripheral Clock: 24Mhz
* CPU Block: 144Mhz

Quoted 5 lines

http://www.nabble.com/file/p19449833/a.JPG a.JPG

Please let me know the correct value of EXCPGCR ? Is 0x28 correct initialize
value of USB clock?

I think that 0x21 is correct value of EXCPGCR for your board.

0x21: 00101000 -> 00 100 001 ->
* 100: Using Internal Clock
* 001: Dividing Ratio Selection is 1/2
(96MHz / 2 = 48MHz)

Quoted 9 lines
Quoted 1 line

And I used my board, I set 0x1500 in PKCR.

I don't understand PKCR - Port control register so I don't know correct initialize value of this register.

0x1500 = 0001 0101 0000 0000
-> PK6 is port output
-> PK5 is port output
-> PK4 is port output
I don't know this value could be set for my board - TEngine/SH7727.

Oh, I am very sorry. This is PECR.
This setting enable USB1_pwr_en and USB2_pwr_en pin.

Best regards,
Yoshihiro Shimoda
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19453016.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#18 lore raw

Hi, thaoth

Quoted 1 line · thaoth

Can you help me to resolve this bug?

I think that it is a problem of the unalignment access. Please change your compiler or change a source code as follows:

common/usb.c +4 -1
index 9502f39..1acf51d 100644
@@ -250,7 +250,10 @@ int usb_set_maxpacket(struct usb_device *dev)
 
 	for(i=0; i<dev->config.bNumInterfaces;i++) {
 		for(ii=0; ii<dev->config.if_desc[i].bNumEndpoints; ii++) {
-			ep = &dev->config.if_desc[i].ep_desc[ii];
+			struct usb_endpoint_descriptor tmp;
+			memcpy(&tmp, &dev->config.if_desc[i].ep_desc[ii],
+				sizeof(struct usb_endpoint_descriptor));
+			ep = &tmp;
 			b=ep->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK;
 
 			if((ep->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)==USB_ENDPOINT_XFER_CONTROL) {	/* Control => bidirectional */
Quoted 1 line

Thank you very much for your supports!

You're welcome! :)

Best regards,
Yoshihiro Shimoda

author
#19 lore raw

Hi,

Quoted 18 lines · Yoshihiro Shimoda
common/usb.c +4 -1
index 9502f39..1acf51d 100644
@@ -250,7 +250,10 @@ int usb_set_maxpacket(struct usb_device *dev)
 
 	for(i=0; i<dev->config.bNumInterfaces;i++) {
 		for(ii=0; ii<dev->config.if_desc[i].bNumEndpoints; ii++) {
-			ep = &dev->config.if_desc[i].ep_desc[ii];
+			struct usb_endpoint_descriptor tmp;
+			memcpy(&tmp, &dev->config.if_desc[i].ep_desc[ii],
+				sizeof(struct usb_endpoint_descriptor));
+			ep = &tmp;
 			b=ep->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK;
 
 			if((ep->bmAttributes &
Quoted 3 lines

USB_ENDPOINT_XFERTYPE_MASK)==USB_ENDPOINT_XFER_CONTROL) { /* Control =>
bidirectional */

Thank you a lot, it worked well. :jumping::jumping::jumping::jumping:

Thank you for good instruction.
Best regards,

Signature · 2 lines
View this message in context: http://www.nabble.com/-T-Engine--UBoot-configuration-for-T-Engine-SH7727-MS7727CP02-DevKit-tp18868090p19453640.html
Sent from the Uboot - Users mailing list archive at Nabble.com.