usb: phy: tegra: HSIC adjustments
Subsystems (2)
cover usb: phy: tegra: HSIC adjustments
Followup to a recent HSIC bringup with a few small improvements.
Svyatoslav Ryhel (4):
usb: phy: tegra: cosmetic fixes
usb: phy: tegra: return error value from utmi_wait_register
usb: phy: tegra: parametrize HSIC PTS value
usb: phy: tegra: parametrize PORTSC1 register offset
drivers/usb/phy/phy-tegra-usb.c | 45 +++++++++++++++---------------- include/linux/usb/tegra_usb_phy.h | 8 ++++-- 2 files changed, 27 insertions(+), 26 deletions(-)
Signature · 1 line
2.51.0
PATCH 1/4 usb: phy: tegra: cosmetic fixes
Change TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC to its literal value instead of using the BIT macro, as it is an enumeration. Correct the spelling in the comment and rename uhsic_registers_shift to uhsic_registers_offset. These changes are cosmetic and do not affect code behavior.
--- drivers/usb/phy/phy-tegra-usb.c | 12 ++++++------ include/linux/usb/tegra_usb_phy.h | 4 ++-- 2 files changed, 8 insertions(+), 8 deletions(-)
drivers/usb/phy/phy-tegra-usb.c +6 -6
@@ -48,7 +48,7 @@#define TEGRA_USB_HOSTPC1_DEVLC 0x1b4#define TEGRA_USB_HOSTPC1_DEVLC_PTS (x) (((x) & 0x7) << 29)#define TEGRA_USB_HOSTPC1_DEVLC_PHCD BIT(22) -#define TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC BIT(2) +#define TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC 4/* Bits of PORTSC1, which will get cleared by writing 1 into them */ #define TEGRA_PORTSC1_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC)
@@ -169,7 +169,7 @@/* * Tegra20 has no UTMIP registers on PHY2 and UHSIC registers start from 0x800 * just where UTMIP registers should have been. This is the case only with Tegra20 -* Tegra30+ have UTMIP registers at 0x800 and UHSIC registers shifter by 0x400 +* Tegra30+ have UTMIP registers at 0x800 and UHSIC registers are shifted by 0x400 * to 0xc00, but register layout is preserved. */ #define UHSIC_PLL_CFG1 0x804
@@ -873,7 +873,7 @@ static int ulpi_phy_power_off(struct tegra_usb_phy *phy)static u32 tegra_hsic_readl (struct tegra_usb_phy *phy,u32 reg) {void __iomem *base = phy->regs; -u32 shift = phy->soc_config->uhsic_registers_shift; +u32 shift = phy->soc_config->uhsic_registers_offset;return readl_relaxed (base + shift + reg); }
@@ -881,7 +881,7 @@ static u32 tegra_hsic_readl(struct tegra_usb_phy *phy, u32 reg)static void tegra_hsic_writel (struct tegra_usb_phy *phy,u32 reg,u32 value) {void __iomem *base = phy->regs; -u32 shift = phy->soc_config->uhsic_registers_shift; +u32 shift = phy->soc_config->uhsic_registers_offset;writel_relaxed (value, base + shift + reg); }
@@ -1469,7 +1469,7 @@ static const struct tegra_phy_soc_config tegra20_soc_config = { .requires_usbmode_setup = false, .requires_extra_tuning_parameters = false, .requires_pmc_ao_power_up = false, - .uhsic_registers_shift = 0, + .uhsic_registers_offset = 0, .uhsic_tx_rtune = 0, /* 40 ohm */ };
@@ -1479,7 +1479,7 @@ static const struct tegra_phy_soc_config tegra30_soc_config = { .requires_usbmode_setup = true, .requires_extra_tuning_parameters = true, .requires_pmc_ao_power_up = true, - .uhsic_registers_shift = 0x400, + .uhsic_registers_offset = 0x400, .uhsic_tx_rtune = 8, /* 50 ohm */ };
include/linux/usb/tegra_usb_phy.h +2 -2
@@ -24,7 +24,7 @@ struct gpio_desc;* requires_extra_tuning_parameters: true if xcvr_hsslew, hssquelch_level * and hsdiscon_level should be set for adequate signal quality * requires_pmc_ao_power_up: true if USB AO is powered down by default -* uhsic_registers_shift: for Tegra30+ where HSIC registers were shifted +* uhsic_registers_offset: for Tegra30+ where HSIC registers were offset * comparing to Tegra20 by 0x400, since Tegra20 has no UTMIP on PHY2 * uhsic_tx_rtune: fine tuned 50 Ohm termination resistor for NMOS/PMOS driver */
@@ -35,7 +35,7 @@ struct tegra_phy_soc_config {bool requires_usbmode_setup;bool requires_extra_tuning_parameters;bool requires_pmc_ao_power_up; -u32 uhsic_registers_shift; +u32 uhsic_registers_offset;u32 uhsic_tx_rtune; };
Signature · 1 line
2.51.0
PATCH 2/4 usb: phy: tegra: return error value from utmi_wait_register
In reply to Svyatoslav RyhelReturn exact error value from utmi_wait_register during HSIC power on.
--- drivers/usb/phy/phy-tegra-usb.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/usb/phy/phy-tegra-usb.c +6 -3
@@ -891,6 +891,7 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy)struct tegra_utmip_config *config = phy->config;void __iomem *base = phy->regs;u32 val; +int err =0 ; val =tegra_hsic_readl (phy,UHSIC_PADS_CFG1 ); val &= ~(UHSIC_PD_BG | UHSIC_PD_TX | UHSIC_PD_TRK | UHSIC_PD_RX |
@@ -984,12 +985,14 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy) val |=UHSIC_TX_RTUNE (phy->soc_config->uhsic_tx_rtune);tegra_hsic_writel (phy,UHSIC_PADS_CFG0 , val); -if (utmi_wait_register (base +USB_SUSP_CTRL ,USB_PHY_CLK_VALID , -USB_PHY_CLK_VALID )) + err =utmi_wait_register (base +USB_SUSP_CTRL ,USB_PHY_CLK_VALID , +USB_PHY_CLK_VALID ); + +if (err)dev_err (phy->u_phy.dev,"Timeout waiting for PHY to stabilize on enable (HSIC)\n" ); -return 0 ; +return err; }static int uhsic_phy_power_off (struct tegra_usb_phy *phy)
Signature · 1 line
2.51.0
Re: [PATCH v1 2/4] usb: phy: tegra: return error value from utmi_wait_register
Quoted 12 lines · Svyatoslav Ryhel
Return exact error value from
utmi_wait_registerduring HSIC power on.Signed-off-by Svyatoslav Ryhel <[email protected]>--- drivers/usb/phy/phy-tegra-usb.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)drivers/usb/phy/phy-tegra-usb.c +0
-0
drivers/usb/phy/phy-tegra-usb.c static int uhsic_phy_power_on(struct tegra_usb_phy *phy) · line 894
Quoted 4 lines
drivers/usb/phy/phy-tegra-usb.c +1
-0@@ -891,6 +891,7 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy)struct tegra_utmip_config *config = phy->config;void __iomem *base = phy->regs;u32 val; +int err =0 ;
This initialization seems pointless -- the newly added variable gets overwritten
by you later...
[...]
Quoted 8 lines
drivers/usb/phy/phy-tegra-usb.c +2
-2@@ -984,12 +985,14 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy) val |=UHSIC_TX_RTUNE (phy->soc_config->uhsic_tx_rtune);tegra_hsic_writel (phy,UHSIC_PADS_CFG0 , val); -if (utmi_wait_register (base +USB_SUSP_CTRL ,USB_PHY_CLK_VALID , -USB_PHY_CLK_VALID )) + err =utmi_wait_register (base +USB_SUSP_CTRL ,USB_PHY_CLK_VALID , +USB_PHY_CLK_VALID );
drivers/usb/phy/phy-tegra-usb.c static int uhsic_phy_power_on(struct tegra_usb_phy *phy) · line 998
Quoted 10 lines
drivers/usb/phy/phy-tegra-usb.c +3
-1+ +if (err)dev_err (phy->u_phy.dev,"Timeout waiting for PHY to stabilize on enable (HSIC)\n" ); -return 0 ; +return err; }static int uhsic_phy_power_off (struct tegra_usb_phy *phy)
MBR, Sergey
Re: [PATCH v1 2/4] usb: phy: tegra: return error value from utmi_wait_register
пн, 2 лют. 2026 р. о 14:05 Sergey Shtylyov <[email protected]> пише:
Quoted 10 lines · Svyatoslav Ryhel
Quoted 8 lines
Return exact error value from
utmi_wait_registerduring HSIC power on.Signed-off-by Svyatoslav Ryhel <[email protected]>--- drivers/usb/phy/phy-tegra-usb.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)
Quoted 13 lines
drivers/usb/phy/phy-tegra-usb.c static int uhsic_phy_power_on(struct tegra_usb_phy *phy) · line 894
Quoted 9 lines
drivers/usb/phy/phy-tegra-usb.c +1
-0@@ -891,6 +891,7 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy)struct tegra_utmip_config *config = phy->config;void __iomem *base = phy->regs;u32 val; +int err =0 ;This initialization seems pointless -- the newly added variable gets overwritten
by you later...
So? let it better be initialized and rewritten then later on catch errors.
Quoted 22 lines
[...]
Quoted 8 lines
drivers/usb/phy/phy-tegra-usb.c +2
-2@@ -984,12 +985,14 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy) val |=UHSIC_TX_RTUNE (phy->soc_config->uhsic_tx_rtune);tegra_hsic_writel (phy,UHSIC_PADS_CFG0 , val); -if (utmi_wait_register (base +USB_SUSP_CTRL ,USB_PHY_CLK_VALID , -USB_PHY_CLK_VALID )) + err =utmi_wait_register (base +USB_SUSP_CTRL ,USB_PHY_CLK_VALID , +USB_PHY_CLK_VALID );drivers/usb/phy/phy-tegra-usb.c static int uhsic_phy_power_on(struct tegra_usb_phy *phy) · line 998
Quoted 10 lines
drivers/usb/phy/phy-tegra-usb.c +3
-1+ +if (err)dev_err (phy->u_phy.dev,"Timeout waiting for PHY to stabilize on enable (HSIC)\n" ); -return 0 ; +return err; }static int uhsic_phy_power_off (struct tegra_usb_phy *phy)MBR, Sergey
Re: [PATCH v1 2/4] usb: phy: tegra: return error value from utmi_wait_register
Quoted 25 lines · Svyatoslav Ryhel
пн, 2 лют. 2026 р. о 14:05 Sergey Shtylyov <[email protected]> пише:
Quoted 10 lines · Svyatoslav Ryhel
Quoted 8 lines
Return exact error value from
utmi_wait_registerduring HSIC power on.Signed-off-by Svyatoslav Ryhel <[email protected]>--- drivers/usb/phy/phy-tegra-usb.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)Quoted 13 lines
drivers/usb/phy/phy-tegra-usb.c static int uhsic_phy_power_on(struct tegra_usb_phy *phy) · line 894
Quoted 9 lines
drivers/usb/phy/phy-tegra-usb.c +1
-0@@ -891,6 +891,7 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy)struct tegra_utmip_config *config = phy->config;void __iomem *base = phy->regs;u32 val; +int err =0 ;This initialization seems pointless -- the newly added variable gets overwritten
by you later...
Quoted 1 line
So? let it better be initialized and rewritten then later on catch errors.
I'm not sure what errors you mean here. To me, it (contrariwise) seems to
mask the possible errors when you forget to set err to e.g. -ENOMEM before returning (when adding a call to kmalloc() or any other function that doesn't return an error code itself)...
I'm pretty sure gcc will drop this initialization when generating the object
code and (what's worse) the static analyzers will trip on this code telling you that the value 0 is unused...
[...]
MBR, Sergey
Re: [PATCH v1 2/4] usb: phy: tegra: return error value from utmi_wait_register
On 2/2/26 9:01 PM, Sergey Shtylyov wrote:
[...]
Quoted 20 lines
Quoted 20 lines
Quoted 20 lines
Quoted 12 lines
Return exact error value from
utmi_wait_registerduring HSIC power on.Signed-off-by Svyatoslav Ryhel <[email protected]>--- drivers/usb/phy/phy-tegra-usb.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)drivers/usb/phy/phy-tegra-usb.c +0
-0drivers/usb/phy/phy-tegra-usb.c static int uhsic_phy_power_on(struct tegra_usb_phy *phy) · line 894
Quoted 4 lines
drivers/usb/phy/phy-tegra-usb.c +1
-0@@ -891,6 +891,7 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy)struct tegra_utmip_config *config = phy->config;void __iomem *base = phy->regs;u32 val; +int err =0 ;This initialization seems pointless -- the newly added variable gets overwritten
by you later...
[...]
Quoted 2 lines
I'm pretty sure gcc will drop this initialization when generating the object
code and (what's worse)
Well, that's actually the good news. I've tried to feed an analogous code to
gcc and clang -- and both seemed to drop the initialization. I was not able to make them complain using C=1 and C=2 with make...
Quoted 2 lines
the static analyzers will trip on this code telling you that the value 0 is unused...
Svace (that we have to use here) surely bitches about that. :-)
[...]
MBR, Sergey
PATCH 3/4 usb: phy: tegra: parametrize HSIC PTS value
In reply to Svyatoslav RyhelThe parallel transceiver select used in HSIC mode differs on Tegra20, where it uses the UTMI value (0), whereas Tegra30+ uses a dedicated HSIC value. Reflect this in the SoC config.
--- drivers/usb/phy/phy-tegra-usb.c | 7 +++---- include/linux/usb/tegra_usb_phy.h | 2 ++ 2 files changed, 5 insertions(+), 4 deletions(-)
drivers/usb/phy/phy-tegra-usb.c +3 -4
@@ -957,10 +957,7 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy)writel_relaxed (val, base +USB_USBMODE ); } -if (phy->soc_config->has_hostpc) -set_pts (phy,TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC ); -else -set_pts (phy,0 ); +set_pts (phy, phy->soc_config->uhsic_pts_value); val =readl_relaxed (base +USB_TXFILLTUNING );if ((val &USB_FIFO_TXFILL_MASK ) !=USB_FIFO_TXFILL_THRES (0x10 )) {
@@ -1474,6 +1471,7 @@ static const struct tegra_phy_soc_config tegra20_soc_config = { .requires_pmc_ao_power_up = false, .uhsic_registers_offset = 0, .uhsic_tx_rtune = 0, /* 40 ohm */ + .uhsic_pts_value = 0, /* UTMI */ };static const struct tegra_phy_soc_config tegra30_soc_config = {
@@ -1484,6 +1482,7 @@ static const struct tegra_phy_soc_config tegra30_soc_config = { .requires_pmc_ao_power_up = true, .uhsic_registers_offset = 0x400, .uhsic_tx_rtune = 8, /* 50 ohm */ + .uhsic_pts_value = TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC, };static const struct of_device_id tegra_usb_phy_id_table[] = {
include/linux/usb/tegra_usb_phy.h +2 -0
@@ -27,6 +27,7 @@ struct gpio_desc;* uhsic_registers_offset: for Tegra30+ where HSIC registers were offset * comparing to Tegra20 by 0x400, since Tegra20 has no UTMIP on PHY2 * uhsic_tx_rtune: fine tuned 50 Ohm termination resistor for NMOS/PMOS driver +* uhsic_pts_value: parallel transceiver select enumeration value */ struct tegra_phy_soc_config {
@@ -37,6 +38,7 @@ struct tegra_phy_soc_config {bool requires_pmc_ao_power_up;u32 uhsic_registers_offset;u32 uhsic_tx_rtune; +u32 uhsic_pts_value; };struct tegra_utmip_config {
Signature · 1 line
2.51.0
PATCH 4/4 usb: phy: tegra: parametrize PORTSC1 register offset
In reply to Svyatoslav RyhelThe PORTSC1 register has a different offset in Tegra20 compared to Tegra30+, yet they share a crucial set of registers required for HSIC functionality. Reflect this register offset change in the SoC config.
--- drivers/usb/phy/phy-tegra-usb.c | 17 ++++++----------- include/linux/usb/tegra_usb_phy.h | 2 ++ 2 files changed, 8 insertions(+), 11 deletions(-)
drivers/usb/phy/phy-tegra-usb.c +6 -11
@@ -965,17 +965,10 @@ static int uhsic_phy_power_on(struct tegra_usb_phy *phy)writel_relaxed (val, base +USB_TXFILLTUNING ); } -if (phy->soc_config->has_hostpc) { - val =readl_relaxed (base +TEGRA30_USB_PORTSC1 ); - val &= ~(TEGRA_USB_PORTSC1_WKOC |TEGRA_USB_PORTSC1_WKDS | -TEGRA_USB_PORTSC1_WKCN ); -writel_relaxed (val, base +TEGRA30_USB_PORTSC1 ); - }else { - val =readl_relaxed (base +TEGRA_USB_PORTSC1 ); - val &= ~(TEGRA_USB_PORTSC1_WKOC |TEGRA_USB_PORTSC1_WKDS | -TEGRA_USB_PORTSC1_WKCN ); -writel_relaxed (val, base +TEGRA_USB_PORTSC1 ); - } + val =readl_relaxed (base + phy->soc_config->portsc1_offset); + val &= ~(TEGRA_USB_PORTSC1_WKOC |TEGRA_USB_PORTSC1_WKDS | +TEGRA_USB_PORTSC1_WKCN ); +writel_relaxed (val, base + phy->soc_config->portsc1_offset); val =tegra_hsic_readl (phy,UHSIC_PADS_CFG0 ); val &= ~UHSIC_TX_RTUNEN ;
@@ -1472,6 +1465,7 @@ static const struct tegra_phy_soc_config tegra20_soc_config = { .uhsic_registers_offset = 0, .uhsic_tx_rtune = 0, /* 40 ohm */ .uhsic_pts_value = 0, /* UTMI */ + .portsc1_offset = TEGRA_USB_PORTSC1, };static const struct tegra_phy_soc_config tegra30_soc_config = {
@@ -1483,6 +1477,7 @@ static const struct tegra_phy_soc_config tegra30_soc_config = { .uhsic_registers_offset = 0x400, .uhsic_tx_rtune = 8, /* 50 ohm */ .uhsic_pts_value = TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC, + .portsc1_offset = TEGRA30_USB_PORTSC1, };static const struct of_device_id tegra_usb_phy_id_table[] = {
include/linux/usb/tegra_usb_phy.h +2 -0
@@ -28,6 +28,7 @@ struct gpio_desc;* comparing to Tegra20 by 0x400, since Tegra20 has no UTMIP on PHY2 * uhsic_tx_rtune: fine tuned 50 Ohm termination resistor for NMOS/PMOS driver * uhsic_pts_value: parallel transceiver select enumeration value +* portsc1_offset: register offset of PORTSC1 */ struct tegra_phy_soc_config {
@@ -39,6 +40,7 @@ struct tegra_phy_soc_config {u32 uhsic_registers_offset;u32 uhsic_tx_rtune;u32 uhsic_pts_value; +u32 portsc1_offset; };struct tegra_utmip_config {
Signature · 1 line
2.51.0
Quoted 8 lines · Svyatoslav Ryhel
Followup to a recent HSIC bringup with a few small improvements.
Svyatoslav Ryhel (4):
usb: phy: tegra: cosmetic fixes
usb: phy: tegra: return error value fromutmi_wait_register
usb: phy: tegra: parametrize HSIC PTS value
usb: phy: tegra: parametrize PORTSC1 register offset
Quoted 5 lines
drivers/usb/phy/phy-tegra-usb.c | 45 +++++++++++++++---------------- include/linux/usb/tegra_usb_phy.h | 8 ++++-- 2 files changed, 27 insertions(+), 26 deletions(-)
Series