SH pinctrl DT support

index c95ea82..e499ff0 100644
@@ -126,3 +126,32 @@ device; they may be grandchildren, for example. Whether this is legal, and
 whether there is any interaction between the child and intermediate parent
 nodes, is again defined entirely by the binding for the individual pin
 controller device.
+
+== Generic pinconf parameters ==
+
+Pin configuration parameters are expressed by DT properties in the pin
+controller device state nodes and child nodes. For devices that use the generic
+pinconf parameters the following properties are defined.
+
+- tristate: A boolean, put the pin into high impedance state when set.
+
+- pull-up: An integer representing the pull-up strength. 0 disables the pull-up,
+  non-zero values enable it.
+
+- pull-down: An integer representing the pull-down strength. 0 disables the
+  pull-down, non-zero values enables it.
+
+- schmitt: An integer, enable or disable Schmitt trigger mode for the pins.
+  Valid values are
+    0: Schmitt trigger disabled (no hysteresis)
+    1: Schmitt trigger enabled
+
+- slew-rate: An integer controlling the pin slew rate. Values are device-
+  dependent.
+
+- drive-strength: An integer representing the drive strength of pins in mA.
+  Valid values are device-dependent.
+
+The pinctrl device DT bindings documentation must list the properties that
+apply to the device, and define the valid range for all device-dependent
+values.

new file mode 100644
index 0000000..6504d65
@@ -0,0 +1,156 @@
+* Renesas Pin Function Controller (GPIO and Pin Mux/Config)
+
+The Pin Function Controller (PFC) is a Pin Mux/Config controller. On SH7372,
+SH73A0, R8A73A4 and R8A7740 it also acts as a GPIO controller.
+
+
+Pin Control
+-----------
+
+Required Properties:
+
+  - compatible: should be one of the following.
+    - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller.
+    - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller.
+    - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller.
+    - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller.
+    - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller.
+    - "renesas,pfc-sh7372": for SH7372 (SH-Mobile AP4) compatible pin-controller.
+    - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller.
+
+  - reg: Base address and length of each memory resource used by the pin
+    controller hardware module.
+
+Optional properties:
+
+  - #gpio-range-cells: Mandatory when the PFC doesn't handle GPIO, forbidden
+    otherwise. Should be 3.
+
+The PFC node also acts as a container for pin configuration nodes. Please refer
+to pinctrl-bindings.txt in this directory for the definition of the term "pin
+configuration node" and for the common pinctrl bindings used by client devices.
+
+Each pin configuration node represents a desired configuration for a pin, a
+pin group, or a list of pins or pin groups. The configuration can include the
+function to select on those pin(s) and pin configuration parameters (such as
+pull-up and pull-down).
+
+Pin configuration nodes contain pin configuration properties, either directly
+or grouped in child subnodes. Both pin muxing and configuration parameters can
+be grouped in that way and referenced as a single pin configuration node by
+client devices.
+
+A configuration node or subnode must reference at least one pin (through the
+pins or pin groups properties) and contain at least a function or one
+configuration parameter. When the function is present only pin groups can be
+used to reference pins.
+
+All pin configuration nodes and subnodes names are ignored. All of those nodes
+are parsed through phandles and processed purely based on their content.
+
+Pin Configuration Node Properties:
+
+- renesas,pins : An array of strings, each string containing the name of a pin.
+- renesas,groups : An array of strings, each string containing the name of a pin
+  group.
+
+- renesas,function: A string containing the name of the function to mux to the
+  pin group(s) specified by the renesas,groups property
+
+  Valid values for pin, group and function names can be found in the group and
+  function arrays of the PFC data file corresponding to the SoC
+  (drivers/pinctrl/sh-pfc/pfc-*.c)
+
+The pin configuration parameters use the generic pinconf bindings defined in
+pinctrl-bindings.txt in this directory. The supported parameters and values are:
+
+- pull-up: 0 disables the pull-up, 1 enables it. Other values must not be used.
+- pull-down: 0 disables the pull-down, 1 enables it. Other values must not be
+  used.
+
+
+GPIO
+----
+
+On SH7372, SH73A0, R8A73A4 and R8A7740 the PFC node is also a GPIO controller
+node.
+
+Required Properties:
+
+  - gpio-controller: Marks the device node as a gpio controller.
+
+  - #gpio-cells: Should be 2. The first cell is the GPIO number and the second
+    cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the
+    GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
+
+The syntax of the gpio specifier used by client nodes should be the following
+with values derived from the SoC user manual.
+
+  <[phandle of the gpio controller node]
+   [pin number within the gpio controller]
+   [flags]>
+
+On other mach-shmobile platforms GPIO is handled by the gpio-rcar driver.
+Please refer to Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt
+for documentation of the GPIO device tree bindings on those platforms.
+
+
+Examples
+--------
+
+Example 1: SH73A0 (SH-Mobile AG5) pin controller node
+
+	pfc: pfc at e6050000 {
+		compatible = "renesas,pfc-sh73a0";
+		reg = <0xe6050000 0x8000>,
+		      <0xe605801c 0x1c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+Example 2: A GPIO LED node that references a GPIO
+
+	#include <dt-bindings/gpio/gpio.h>
+
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			gpios = <&pfc 20 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+Example 3: KZM-A9-GT (SH-Mobile AG5) default pin state hog and pin control maps
+           for the MMCIF and SCIFA4 devices
+
+	&pfc {
+		pinctrl-0 = <&scifa4_pins>;
+		pinctrl-names = "default";
+
+		mmcif_pins: mmcif {
+			mux {
+				renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0";
+				renesas,function = "mmc0";
+			};
+			cfg {
+				renesas,groups = "mmc0_data8_0";
+				renesas,pins = "PORT279";
+				pull-up = <1>;
+			};
+		};
+
+		scifa4_pins: scifa4 {
+			renesas,groups = "scifa4_data", "scifa4_ctrl";
+			renesas,function = "scifa4";
+		};
+	};
+
+Example 4: KZM-A9-GT (SH-Mobile AG5) default pin state for the MMCIF device
+
+	&mmcif {
+		pinctrl-0 = <&mmcif_pins>;
+		pinctrl-names = "default";
+
+		bus-width = <8>;
+		vmmc-supply = <&reg_1p8v>;
+		status = "okay";
+	};

index 4ff2019..5aa1180 100644
@@ -85,4 +85,11 @@
 		interrupt-parent = <&gic>;
 		interrupts = <0 69 4>;
 	};
+
+	pfc: pfc at e6050000 {
+		compatible = "renesas,pfc-r8a73a4";
+		reg = <0xe6050000 0x9000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };

index 25dc930..2fa3708 100644
@@ -135,4 +135,12 @@
 			      0 72 0x4
 			      0 73 0x4>;
 	};
+
+	pfc: pfc at e6050000 {
+		compatible = "renesas,pfc-r8a7740";
+		reg = <0xe6050000 0x8000>,
+		      <0xe605800c 0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };

index 4743735..c8dbf14 100644
@@ -32,4 +32,9 @@
 		reg = <0xfe438000 0x1000>,
 		      <0xfe430000 0x100>;
 	};
+
+	pfc: pfc at fffc0000 {
+		compatible = "renesas,pfc-r8a7778";
+		reg = <0xfffc000 0x118>;
+	};
 };

index c8dbf14..0639e8b 100644
@@ -33,8 +33,59 @@
 		      <0xfe430000 0x100>;
 	};
 
+	gpio0: gpio at ffc40000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc40000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 0 32>;
+	};
+
+	gpio1: gpio at ffc41000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc41000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 32 32>;
+	};
+
+	gpio2: gpio at ffc42000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc42000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 64 32>;
+	};
+
+	gpio3: gpio at ffc43000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc43000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 96 32>;
+	};
+
+	gpio4: gpio at ffc44000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc44000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 128 27>;
+	};
+
 	pfc: pfc at fffc0000 {
 		compatible = "renesas,pfc-r8a7778";
 		reg = <0xfffc000 0x118>;
+		#gpio-range-cells = <3>;
 	};
 };

index 7f146c6..9dfc438 100644
@@ -101,6 +101,11 @@
 		interrupts = <0 81 0x4>;
 	};
 
+	pfc: pfc at fffc0000 {
+		compatible = "renesas,pfc-r8a7779";
+		reg = <0xfffc0000 0x23c>;
+	};
+
 	thermal at ffc48000 {
 		compatible = "renesas,rcar-thermal";
 		reg = <0xffc48000 0x38>;

index 9dfc438..2bbb4cb 100644
@@ -48,6 +48,76 @@
                       <0xf0000100 0x100>;
         };
 
+	gpio0: gpio at ffc40000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc40000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 141 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 0 32>;
+	};
+
+	gpio1: gpio at ffc41000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc41000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 142 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 32 32>;
+	};
+
+	gpio2: gpio at ffc42000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc42000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 143 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 64 32>;
+	};
+
+	gpio3: gpio at ffc43000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc43000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 144 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 96 32>;
+	};
+
+	gpio4: gpio at ffc44000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc44000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 145 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 128 32>;
+	};
+
+	gpio5: gpio at ffc45000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc45000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 146 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 160 32>;
+	};
+
+	gpio6: gpio at ffc46000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc46000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 147 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 192 9>;
+	};
+
 	irqpin0: irqpin at fe780010 {
 		compatible = "renesas,intc-irqpin";
 		#interrupt-cells = <2>;

@@ -104,6 +174,7 @@
 	pfc: pfc at fffc0000 {
 		compatible = "renesas,pfc-r8a7779";
 		reg = <0xfffc0000 0x23c>;
+		#gpio-range-cells = <3>;
 	};
 
 	thermal at ffc48000 {

index 339d9b1..13caf12 100644
@@ -54,4 +54,9 @@
 		interrupt-parent = <&gic>;
 		interrupts = <0 0 4>, <0 1 4>, <0 2 4>,	<0 3 4>;
 	};
+
+	pfc: pfc at e6060000 {
+		compatible = "renesas,pfc-r8a7790";
+		reg = <0 0xe6060000 0 0x250>;
+	};
 };

index 13caf12..1b75c1d 100644
@@ -38,6 +38,66 @@
 		interrupts = <1 9 0xf04>;
 	};
 
+	gpio0: gpio at ffc40000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc40000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 4 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 0 32>;
+	};
+
+	gpio1: gpio at ffc41000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc41000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 5 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 32 32>;
+	};
+
+	gpio2: gpio at ffc42000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc42000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 6 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 64 32>;
+	};
+
+	gpio3: gpio at ffc43000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc43000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 7 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 96 32>;
+	};
+
+	gpio4: gpio at ffc44000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc44000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 8 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 128 32>;
+	};
+
+	gpio5: gpio at ffc45000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc45000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 9 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 160 32>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <1 13 0xf08>,

@@ -58,5 +118,6 @@
 	pfc: pfc at e6060000 {
 		compatible = "renesas,pfc-r8a7790";
 		reg = <0 0xe6060000 0 0x250>;
+		#gpio-range-cells = <3>;
 	};
 };

index 677fc60..ce19398 100644
@@ -18,4 +18,12 @@
 			compatible = "arm,cortex-a8";
 		};
 	};
+
+	pfc: pfc at e6050000 {
+		compatible = "renesas,pfc-sh7372";
+		reg = <0xe6050000 0x8000>,
+		      <0xe605801c 0x1c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };

index ec40bf7..abe02d6 100644
@@ -222,4 +222,12 @@
 		cap-sd-highspeed;
 		status = "disabled";
 	};
+
+	pfc: pfc at e6050000 {
+		compatible = "renesas,pfc-sh73a0";
+		reg = <0xe6050000 0x8000>,
+		      <0xe605801c 0x1c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };

index 09ea22c..4a7ae32 100644
@@ -43,3 +43,13 @@
 		interrupts = <2 0>; /* IRQ10: hwirq 2 on irqpin1 */
 	};
 };
+
+&pfc {
+	pinctrl-0 = <&scifa1_pins>;
+	pinctrl-names = "default";
+
+	scifa1_pins: scifa1 {
+		renesas,groups = "scifa1_data";
+		renesas,function = "scifa1";
+	};
+};

index 4a7ae32..a6c6606 100644
@@ -41,6 +41,8 @@
 		reg = <0x55>;
 		interrupt-parent = <&irqpin1>;
 		interrupts = <2 0>; /* IRQ10: hwirq 2 on irqpin1 */
+		pinctrl-0 = <&st1232_pins>;
+		pinctrl-names = "default";
 	};
 };
 

@@ -52,4 +54,9 @@
 		renesas,groups = "scifa1_data";
 		renesas,function = "scifa1";
 	};
+
+	st1232_pins: st1232 {
+		renesas,groups = "intc_irq10";
+		renesas,function = "intc";
+	};
 };

index a6c6606..8ec4cd1 100644
@@ -10,6 +10,7 @@
 
 /dts-v1/;
 /include/ "r8a7740.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "armadillo 800 eva reference";

@@ -43,6 +44,7 @@
 		interrupts = <2 0>; /* IRQ10: hwirq 2 on irqpin1 */
 		pinctrl-0 = <&st1232_pins>;
 		pinctrl-names = "default";
+		gpios = <&pfc 166 GPIO_ACTIVE_LOW>;
 	};
 };
 

index 8ec4cd1..366f729 100644
@@ -34,6 +34,21 @@
 		regulator-boot-on;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			gpios = <&pfc 102 GPIO_ACTIVE_HIGH>;
+		};
+		led2 {
+			gpios = <&pfc 111 GPIO_ACTIVE_HIGH>;
+		};
+		led3 {
+			gpios = <&pfc 110 GPIO_ACTIVE_HIGH>;
+		};
+		led4 {
+			gpios = <&pfc 177 GPIO_ACTIVE_HIGH>;
+		};
+	};
 };
 
 &i2c0 {

index b6f759e..24f7b04 100644
@@ -145,19 +145,70 @@
 	};
 };
 
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+};
+
 &mmcif {
+	pinctrl-0 = <&mmcif_pins>;
+	pinctrl-names = "default";
+
 	bus-width = <8>;
 	vmmc-supply = <&reg_1p8v>;
 	status = "okay";
 };
 
+&pfc {
+	pinctrl-0 = <&scifa4_pins>;
+	pinctrl-names = "default";
+
+	i2c3_pins: i2c3 {
+		renesas,groups = "i2c3_1";
+		renesas,function = "i2c3";
+	};
+
+	mmcif_pins: mmcif {
+		mux {
+			renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0";
+			renesas,function = "mmc0";
+		};
+		cfg {
+			renesas,groups = "mmc0_data8_0";
+			renesas,pins = "PORT279";
+			pull-up = <1>;
+		};
+	};
+
+	scifa4_pins: scifa4 {
+		renesas,groups = "scifa4_data", "scifa4_ctrl";
+		renesas,function = "scifa4";
+	};
+
+	sdhi0_pins: sdhi0 {
+		renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd", "sdhi0_wp";
+		renesas,function = "sdhi0";
+	};
+
+	sdhi2_pins: sdhi2 {
+		renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
+		renesas,function = "sdhi2";
+	};
+};
+
 &sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-names = "default";
+
 	vmmc-supply = <&reg_3p3v>;
 	bus-width = <4>;
 	status = "okay";
 };
 
 &sdhi2 {
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-names = "default";
+
 	vmmc-supply = <&reg_3p3v>;
 	bus-width = <4>;
 	broken-cd;

index 24f7b04..6374965 100644
@@ -13,6 +13,7 @@
 
 /dts-v1/;
 /include/ "sh73a0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "KZM-A9-GT";

@@ -58,6 +59,24 @@
 		regulator-boot-on;
 	};
 
+	vmmc_sdhi0: regulator at 2 {
+	        compatible = "regulator-fixed";
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pfc 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vmmc_sdhi2: regulator at 3 {
+	        compatible = "regulator-fixed";
+		regulator-name = "SDHI2 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pfc 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	lan9220 at 10000000 {
 		compatible = "smsc,lan9220", "smsc,lan9115";
 		reg = <0x10000000 0x100>;

@@ -200,7 +219,7 @@
 	pinctrl-0 = <&sdhi0_pins>;
 	pinctrl-names = "default";
 
-	vmmc-supply = <&reg_3p3v>;
+	vmmc-supply = <&vmmc_sdhi0>;
 	bus-width = <4>;
 	status = "okay";
 };

@@ -209,7 +228,7 @@
 	pinctrl-0 = <&sdhi2_pins>;
 	pinctrl-names = "default";
 
-	vmmc-supply = <&reg_3p3v>;
+	vmmc-supply = <&vmmc_sdhi2>;
 	bus-width = <4>;
 	broken-cd;
 	status = "okay";

index 6374965..a416eee 100644
@@ -89,6 +89,22 @@
 		vddvario-supply = <&reg_1p8v>;
 		vdd33a-supply = <&reg_3p3v>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			gpios = <&pfc 20 GPIO_ACTIVE_LOW>;
+		};
+		led2 {
+			gpios = <&pfc 21 GPIO_ACTIVE_LOW>;
+		};
+		led3 {
+			gpios = <&pfc 22 GPIO_ACTIVE_LOW>;
+		};
+		led4 {
+			gpios = <&pfc 23 GPIO_ACTIVE_LOW>;
+		};
+	};
 };
 
 &i2c0 {

index 72be4c8..6d20247 100644
@@ -37,6 +37,9 @@
 	lan0 at 18000000 {
 		compatible = "smsc,lan9220", "smsc,lan9115";
 		reg = <0x18000000 0x100>;
+		pinctrl-0 = <&lan0_pins>;
+		pinctrl-names = "default";
+
 		phy-mode = "mii";
 		interrupt-parent = <&gic>;
 		interrupts = <0 28 0x4>;

@@ -45,3 +48,35 @@
 		vdd33a-supply = <&fixedregulator3v3>;
 	};
 };
+
+&pfc {
+	pinctrl-0 = <&scif2_pins &scif4_pins &sdhi0_pins>;
+	pinctrl-names = "default";
+
+	lan0_pins: lan0 {
+		intc {
+			renesas,groups = "intc_irq1_b";
+			renesas,function = "intc";
+		};
+		lbsc {
+			renesas,groups = "lbsc_ex_cs0";
+			renesas,function = "lbsc";
+		};
+	};
+
+	scif2_pins: scif2 {
+		renesas,groups = "scif2_data_c";
+		renesas,function = "scif2";
+	};
+
+	scif4_pins: scif4 {
+		renesas,groups = "scif4_data";
+		renesas,function = "scif4";
+	};
+
+	sdhi0_pins: sdhi0 {
+		renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd",
+				 "sdhi0_wp";
+		renesas,function = "sdhi0";
+	};
+};

index 6d20247..b64705b 100644
@@ -11,6 +11,7 @@
 
 /dts-v1/;
 /include/ "r8a7779.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "marzen";

@@ -47,6 +48,19 @@
 		vddvario-supply = <&fixedregulator3v3>;
 		vdd33a-supply = <&fixedregulator3v3>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		led2 {
+			gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+		};
+		led3 {
+			gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+		};
+		led4 {
+			gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
 };
 
 &pfc {