KVM: x86: Make bus clock frequency for vAPIC timer configurable
Subsystems (6)
v4 cover KVM: x86: Make bus clock frequency for vAPIC timer configurable
(I am helping Isaku for a bit by submitting the next versions of this
series.)
Changes from v3:
- v3: https://lore.kernel.org/all/[email protected]/
- Reworked all changelogs.
- Regarding code changes: patches #1 and #2 are unchanged, patch #3 was reworked according to Sean's guidance, and patch #4 (the test) needed changes after rebase to kvm-x86/next and the implementation (patch #3) changes.
- Added Reviewed-by tags to patches #1, #2, and #4, but removed Maxim's Reviewed-by tag from patch #3 because it changed so much.
- Added a "Suggested-by" to patch #4 to reflect that it represents Sean's guidance.
- Reworked cover to match customs (in subject line) and reflect feedback to patches: capability renamed to KVM_CAP_X86_APIC_BUS_FREQUENCY, clarify distinction between "core crystal clock" and "bus clock", and update pro/con list.
- Please refer to individual patches for detailed changes.
Changes from v2:
- v2: https://lore.kernel.org/lkml/[email protected]/
- Removed APIC_BUS_FREQUENCY and apic_bus_frequency of struct kvm-arch.
- Update the commit messages.
- Added reviewed-by (Maxim Levitsky)
- Use 1.5GHz instead of 1GHz as frequency for the test case.
Changes from v1:
- v1: https://lore.kernel.org/all/[email protected]/
- Added a test case
- Fix a build error for i386 platform
- Add check if vcpu isn't created.
- Add check if lapic chip is in-kernel emulation.
- Updated api.rst
Summary
-------
Add KVM_CAP_X86_APIC_BUS_FREQUENCY capability to configure the APIC bus clock frequency for APIC timer emulation.
Allow KVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY) to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf 0x15 to advertise the frequency.
Description
-----------
Vishal reported [1] that the TDX guest kernel expects a 25MHz APIC bus frequency but ends up getting interrupts at a significantly higher rate.
The TDX architecture hard-codes the core crystal clock frequency to 25MHz and mandates exposing it via CPUID leaf 0x15. The TDX architecture does not allow the VMM to override the value.
In addition, per Intel SDM:
"The APIC timer frequency will be the processor’s bus clock or core
crystal clock frequency (when TSC/core crystal clock ratio is enumerated in CPUID leaf 0x15) divided by the value specified in the divide configuration register."
The resulting 25MHz APIC bus frequency conflicts with the KVM hardcoded APIC bus frequency of 1GHz.
The KVM doesn't enumerate CPUID leaf 0x15 to the guest unless the user space VMM sets it using KVM_SET_CPUID. If the CPUID leaf 0x15 is enumerated, the guest kernel uses it as the APIC bus frequency. If not, the guest kernel measures the frequency based on other known timers like the ACPI timer or the legacy PIT. As reported in [1] the TDX guest kernel expects a 25MHz timer frequency but gets timer interrupt more frequently due to the 1GHz frequency used by KVM.
To ensure that the guest doesn't have a conflicting view of the APIC bus frequency, allow the userspace to tell KVM to use the same frequency that TDX mandates instead of the default 1Ghz.
There are several options to address this:
1. Make the KVM able to configure APIC bus frequency (this series).
Pro: It resembles the existing hardware. The recent Intel CPUs
adopts 25MHz.
Con: Require the VMM to emulate the APIC timer at 25MHz.
2. Make the TDX architecture enumerate CPUID leaf 0x15 to configurable frequency or not enumerate it.
Pro: Any APIC bus frequency is allowed.
Con: Deviates from TDX architecture.
3. Make the TDX guest kernel use 1GHz when it's running on KVM.
Con: The kernel ignores CPUID leaf 0x15.
4. Change CPUID leaf 0x15 under TDX to report the crystal clock frequency as 1 GHz.
Pro: This has been the virtual APIC frequency for KVM guests for 13
years.
Pro: This requires changing only one hard-coded constant in TDX.
Con: It doesn't work with other VMMs as TDX isn't specific to KVM.
Con: Core crystal clock frequency is also used to calculate TSC frequency.
Con: If it is configured to value different from hardware, it will
break the correctness of INTEL-PT Mini Time Count (MTC) packets in TDs.
[1] https://lore.kernel.org/lkml/[email protected]/
Isaku Yamahata (4):
KVM: x86: hyper-v: Calculate APIC bus frequency for Hyper-V
KVM: x86: Make nsec per APIC bus cycle a VM variable
KVM: x86: Add a capability to configure bus frequency for APIC timer
KVM: selftests: Add test for configure of x86 APIC bus frequency
Documentation/virt/kvm/api.rst | 17 ++ arch/x86/include/asm/kvm_host.h | 1 + arch/x86/kvm/hyperv.c | 3 +- arch/x86/kvm/lapic.c | 6 +- arch/x86/kvm/lapic.h | 3 +- arch/x86/kvm/x86.c | 28 +++ include/uapi/linux/kvm.h | 1 + tools/testing/selftests/kvm/Makefile | 1 + .../selftests/kvm/include/x86_64/apic.h | 7 + .../kvm/x86_64/apic_bus_clock_test.c | 166 ++++++++++++++++++ 10 files changed, 228 insertions(+), 5 deletions(-) create mode 100644 tools/testing/selftests/kvm/x86_64/apic_bus_clock_test.c
base-commit: 964d0c614c7f71917305a5afdca9178fe8231434
Signature · 1 line
2.34.1
PATCH v4 1/4 KVM: x86: hyper-v: Calculate APIC bus frequency for Hyper-V
From: Isaku Yamahata <[email protected]>
Remove APIC_BUS_FREQUENCY and calculate it based on nanoseconds per APIC bus cycle. APIC_BUS_FREQUENCY is used only for HV_X64_MSR_APIC_FREQUENCY. The MSR is not frequently read, calculate it every time.
There are two constants related to the APIC bus frequency:APIC_BUS_FREQUENCY and APIC_BUS_CYCLE_NS.
Only one value is required because one can be calculated from the other:
APIC_BUS_CYCLES_NS = 1000 * 1000 * 1000 / APIC_BUS_FREQUENCY.
Remove APIC_BUS_FREQUENCY and instead calculate it when needed. This prepares for support of configurable APIC bus frequency by requiring to change only a single variable.
---
Changes v4:
- Modify subject to match custom: "KVM: x86/hyperv:" -> "KVM: x86: hyper-v:" and use standard capitalization for Hyper-V ("hyper-v" -> "Hyper-V").
- Rework changelog to remove pronouns ("we").
- Change logic in commit log: "APIC bus cycles per NS" -> "nanoseconds per APIC bus cycle".
- Fix typos. (Maxim and Xiaoyao)
- Add Maxim and Xiaoyao's Reviewed-by tags.
- Add Maxim's "Suggested-by".
Changes v3:
- Newly added according to Maxim Levitsky suggestion.
arch/x86/kvm/hyperv.c | 2 +- arch/x86/kvm/lapic.h | 1 - 2 files changed, 1 insertion(+), 2 deletions(-)
arch/x86/kvm/hyperv.c +1 -1
@@ -1737,7 +1737,7 @@ static int kvm_hv_get_msr(struct kvm_vcpu *vcpu, u32 msr, u64 *pdata, data = (u64 )vcpu->arch.virtual_tsc_khz *1000 ;break ;case HV_X64_MSR_APIC_FREQUENCY : - data =APIC_BUS_FREQUENCY ; + data =div64_u64 (1000000000ULL ,APIC_BUS_CYCLE_NS );break ;default :kvm_pr_unimpl_rdmsr (vcpu, msr);
arch/x86/kvm/lapic.h +0 -1
@@ -17,7 +17,6 @@#define APIC_DEST_MASK 0x800#define APIC_BUS_CYCLE_NS 1 -#define APIC_BUS_FREQUENCY (1000000000ULL / APIC_BUS_CYCLE_NS)#define APIC_BROADCAST 0xFF#define X2APIC_BROADCAST 0xFFFFFFFFul
Signature · 1 line
2.34.1
Re: [PATCH V4 1/4] KVM: x86: hyper-v: Calculate APIC bus frequency for Hyper-V
Quoted 15 lines · Reinette Chatre
From: Isaku Yamahata <[email protected]>
Remove
APIC_BUS_FREQUENCYand calculate it based on nanoseconds per APIC bus cycle.APIC_BUS_FREQUENCYis used only forHV_X64_MSR_APIC_FREQUENCY. The MSR is not frequently read, calculate it every time.There are two constants related to the APIC bus frequency:
APIC_BUS_FREQUENCYandAPIC_BUS_CYCLE_NS.
Only one value is required because one can be calculated from the other:
APIC_BUS_CYCLES_NS= 1000 * 1000 * 1000 /APIC_BUS_FREQUENCY.Remove
APIC_BUS_FREQUENCYand instead calculate it when needed. This prepares for support of configurable APIC bus frequency by requiring to change only a single variable.
Quoted 6 lines
Suggested-by Maxim Levitsky <[email protected]>Signed-off-by Isaku Yamahata <[email protected]>Reviewed-by Maxim Levitsky <[email protected]>Reviewed-by Xiaoyao Li <[email protected]>[reinette: rework changelog]Signed-off-by Reinette Chatre <[email protected]>
PATCH v4 2/4 KVM: x86: Make nsec per APIC bus cycle a VM variable
In reply to Reinette ChatreFrom: Isaku Yamahata <[email protected]>
Introduce the VM variable "nanoseconds per APIC bus cycle" in preparation to make the APIC bus frequency configurable.
The TDX architecture hard-codes the core crystal clock frequency to 25MHz and mandates exposing it via CPUID leaf 0x15. The TDX architecture does not allow the VMM to override the value.
In addition, per Intel SDM:
"The APIC timer frequency will be the processor’s bus clock or core
crystal clock frequency (when TSC/core crystal clock ratio is enumerated in CPUID leaf 0x15) divided by the value specified in the divide configuration register."
The resulting 25MHz APIC bus frequency conflicts with the KVM hardcoded APIC bus frequency of 1GHz.
Introduce the VM variable "nanoseconds per APIC bus cycle" to prepare for allowing userspace to tell KVM to use the frequency that TDX mandates instead of the default 1Ghz. Doing so ensures that the guest doesn't have a conflicting view of the APIC bus frequency.
---
Changes v4:
- Reword changelog to address comments related to "bus clock" vs "core crystal clock" frequency. (Xiaoyao)
- Typo in changelog ("APIC APIC" -> "APIC").
- Change logic "APIC bus cycles per nsec" -> "nanoseconds per APIC bus cycle".
Changes V3:
- Update commit message.
- Dropped apic_bus_frequency according to Maxim Levitsky.
Changes v2:
- No change.
arch/x86/include/asm/kvm_host.h | 1 + arch/x86/kvm/hyperv.c | 3 ++- arch/x86/kvm/lapic.c | 6 ++++-- arch/x86/kvm/lapic.h | 2 +- arch/x86/kvm/x86.c | 1 + 5 files changed, 9 insertions(+), 4 deletions(-)
arch/x86/include/asm/kvm_host.h +1 -0
@@ -1359,6 +1359,7 @@ struct kvm_arch {u32 default_tsc_khz;bool user_set_tsc; +u64 apic_bus_cycle_ns;seqcount_raw_spinlock_t pvclock_sc;bool use_master_clock;
arch/x86/kvm/hyperv.c +2 -1
@@ -1737,7 +1737,8 @@ static int kvm_hv_get_msr(struct kvm_vcpu *vcpu, u32 msr, u64 *pdata, data = (u64 )vcpu->arch.virtual_tsc_khz *1000 ;break ;case HV_X64_MSR_APIC_FREQUENCY : - data =div64_u64 (1000000000ULL ,APIC_BUS_CYCLE_NS ); + data =div64_u64 (1000000000ULL , + vcpu->kvm->arch.apic_bus_cycle_ns);break ;default :kvm_pr_unimpl_rdmsr (vcpu, msr);
arch/x86/kvm/lapic.c +4 -2
@@ -1547,7 +1547,8 @@ static u32 apic_get_tmcct(struct kvm_lapic *apic) remaining =0 ; ns =mod_64 (ktime_to_ns (remaining), apic->lapic_timer.period); -return div64_u64 (ns, (APIC_BUS_CYCLE_NS * apic->divide_count)); +return div64_u64 (ns, (apic->vcpu->kvm->arch.apic_bus_cycle_ns * + apic->divide_count)); }static void __report_tpr_access (struct kvm_lapic *apic,bool write)
@@ -1965,7 +1966,8 @@ static void start_sw_tscdeadline(struct kvm_lapic *apic)static inline u64 tmict_to_ns (struct kvm_lapic *apic,u32 tmict) { -return (u64 )tmict *APIC_BUS_CYCLE_NS * (u64 )apic->divide_count; +return (u64 )tmict * apic->vcpu->kvm->arch.apic_bus_cycle_ns * + (u64 )apic->divide_count; }static void update_target_expiration (struct kvm_lapic *apic,uint32_t old_divisor)
arch/x86/kvm/lapic.h +1 -1
@@ -16,7 +16,7 @@#define APIC_DEST_NOSHORT 0x0#define APIC_DEST_MASK 0x800 -#define APIC_BUS_CYCLE_NS 1 +#define APIC_BUS_CYCLE_NS_DEFAULT 1#define APIC_BROADCAST 0xFF#define X2APIC_BROADCAST 0xFFFFFFFFul
arch/x86/kvm/x86.c +1 -0
@@ -12559,6 +12559,7 @@ int kvm_arch_init_vm(struct kvm *kvm, unsigned long type)raw_spin_unlock_irqrestore (&kvm->arch.tsc_write_lock, flags); kvm->arch.default_tsc_khz = max_tsc_khz ? : tsc_khz; + kvm->arch.apic_bus_cycle_ns =APIC_BUS_CYCLE_NS_DEFAULT ; kvm->arch.guest_can_read_msr_platform_info = true; kvm->arch.enable_pmu = enable_pmu;
Signature · 1 line
2.34.1
Re: [PATCH V4 2/4] KVM: x86: Make nsec per APIC bus cycle a VM variable
Quoted 23 lines · Reinette Chatre
From: Isaku Yamahata <[email protected]>
Introduce the VM variable "nanoseconds per APIC bus cycle" in preparation to make the APIC bus frequency configurable.
The TDX architecture hard-codes the core crystal clock frequency to 25MHz and mandates exposing it via CPUID leaf
0x15. The TDX architecture does not allow the VMM to override the value.In addition, per Intel SDM:
"The APIC timer frequency will be the processor’s bus clock or core crystal clock frequency (when TSC/core crystal clock ratio is enumerated in CPUID leaf0x15) divided by the value specified in the divide configuration register."The resulting 25MHz APIC bus frequency conflicts with the KVM hardcoded APIC bus frequency of 1GHz.
Introduce the VM variable "nanoseconds per APIC bus cycle" to prepare for allowing userspace to tell KVM to use the frequency that TDX mandates instead of the default 1Ghz. Doing so ensures that the guest doesn't have a conflicting view of the APIC bus frequency.
Quoted 4 lines
Signed-off-by Isaku Yamahata <[email protected]>Reviewed-by Maxim Levitsky <[email protected]>[reinette: rework changelog]Signed-off-by Reinette Chatre <[email protected]>
PATCH v4 3/4 KVM: x86: Add a capability to configure bus frequency for APIC timer
In reply to Reinette ChatreFrom: Isaku Yamahata <[email protected]>
Add KVM_CAP_X86_APIC_BUS_FREQUENCY capability to configure the APIC bus clock frequency for APIC timer emulation.
Allow KVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY) to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf 0x15 to advertise the frequency.
Vishal reported that the TDX guest kernel expects a 25MHz APIC bus frequency but ends up getting interrupts at a significantly higher rate.
The TDX architecture hard-codes the core crystal clock frequency to 25MHz and mandates exposing it via CPUID leaf 0x15. The TDX architecture does not allow the VMM to override the value.
In addition, per Intel SDM:
"The APIC timer frequency will be the processor’s bus clock or core
crystal clock frequency (when TSC/core crystal clock ratio is enumerated in CPUID leaf 0x15) divided by the value specified in the divide configuration register."
The resulting 25MHz APIC bus frequency conflicts with the KVM hardcoded APIC bus frequency of 1GHz.
The KVM doesn't enumerate CPUID leaf 0x15 to the guest unless the user space VMM sets it using KVM_SET_CPUID. If the CPUID leaf 0x15 is enumerated, the guest kernel uses it as the APIC bus frequency. If not, the guest kernel measures the frequency based on other known timers like the ACPI timer or the legacy PIT. As reported by Vishal the TDX guest kernel expects a 25MHz timer frequency but gets timer interrupt more frequently due to the 1GHz frequency used by KVM.
To ensure that the guest doesn't have a conflicting view of the APIC bus frequency, allow the userspace to tell KVM to use the same frequency that TDX mandates instead of the default 1Ghz.
There are several options to address this:
1. Make the KVM able to configure APIC bus frequency (this series).
Pro: It resembles the existing hardware. The recent Intel CPUs
adapts 25MHz.
Con: Require the VMM to emulate the APIC timer at 25MHz.
2. Make the TDX architecture enumerate CPUID leaf 0x15 to configurable frequency or not enumerate it.
Pro: Any APIC bus frequency is allowed.
Con: Deviates from TDX architecture.
3. Make the TDX guest kernel use 1GHz when it's running on KVM.
Con: The kernel ignores CPUID leaf 0x15.
4. Change CPUID leaf 0x15 under TDX to report the crystal clock frequency as 1 GHz.
Pro: This has been the virtual APIC frequency for KVM guests for 13
years.
Pro: This requires changing only one hard-coded constant in TDX.
Con: It doesn't work with other VMMs as TDX isn't specific to KVM.
Con: Core crystal clock frequency is also used to calculate TSC
frequency.
Con: If it is configured to value different from hardware, it will
break the correctness of INTEL-PT Mini Time Count (MTC) packets in TDs.
---
Changes v4:
- Rework implementation following Sean's guidance in:
https://lore.kernel.org/all/[email protected]/
- Reword con #2 to acknowledge feedback. (Sean)
- Add the "con" information from Xiaoyao during earlier review of v2.
- Rework changelog to address comments related to "bus clock" vs "core crystal clock" frequency. (Xiaoyao)
- Drop snippet about impact on TSC deadline timer emulation. (Maxim)
- Drop Maxim Levitsky's "Reviewed-by" tag due to many changes to patch since tag received.
- Switch "Subject:" to match custom "KVM: X86:" -> "KVM: x86:"
Changes v3:
- Added reviewed-by Maxim Levitsky.
- Minor update of the commit message.
Changes v2:
- Add check if vcpu isn't created.
- Add check if lapic chip is in-kernel emulation.
- Fix build error for i386.
- Add document to api.rst.
- Typo in the commit message.
Documentation/virt/kvm/api.rst | 17 +++++++++++++++++ arch/x86/kvm/x86.c | 27 +++++++++++++++++++++++++++ include/uapi/linux/kvm.h | 1 + 3 files changed, 45 insertions(+)
Documentation/virt/kvm/api.rst +17 -0
@@ -8063,6 +8063,23 @@ error/annotated fault. See KVM_EXIT_MEMORY_FAULT for more information. +7.35 KVM_CAP_X86_APIC_BUS_FREQUENCY +----------------------------------- + +:Architectures: x86 +:Target: VM +:Parameters: args[0] is the desired APIC bus clock rate, in nanoseconds +:Returns: 0 on success, -EINVAL if args[0] contains an invalid value for the + frequency or if any vCPUs have been created, -ENXIO if a virtual + local APIC has not been created using KVM_CREATE_IRQCHIP. + +This capability sets VM's APIC bus clock frequency, used by KVM's in-kernel +virtual APIC when emulating APIC timers. KVM's default value can be retrieved +by KVM_CHECK_EXTENSION. + +Note: Userspace is responsible for correctly configuring CPUID 0x15, a.k.a. the +core crystal clock frequency, if a non-zero CPUID 0x15 is exposed to the guest. + 8. Other capabilities. ======================
arch/x86/kvm/x86.c +27 -0
@@ -4713,6 +4713,9 @@ int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)case KVM_CAP_MEMORY_FAULT_INFO : r =1 ;break ; +case KVM_CAP_X86_APIC_BUS_FREQUENCY : + r =APIC_BUS_CYCLE_NS_DEFAULT ; +break ;case KVM_CAP_EXIT_HYPERCALL : r =KVM_EXIT_HYPERCALL_VALID_MASK ;break ;
@@ -6726,6 +6729,30 @@ int kvm_vm_ioctl_enable_cap(struct kvm *kvm, }mutex_unlock (&kvm->lock);break ; +case KVM_CAP_X86_APIC_BUS_FREQUENCY : { +u64 bus_cycle_ns = cap->args[0 ]; +u64 unused; + + r = -EINVAL ; +/* +* Guard against overflow in tmict_to_ns(). 128 is the highest +* divide value that can be programmed in APIC_TDCR. +*/ +if (!bus_cycle_ns || +check_mul_overflow ((u64 )U32_MAX *128 , bus_cycle_ns, &unused)) +break ; + + r =0 ; +mutex_lock (&kvm->lock); +if (!irqchip_in_kernel (kvm)) + r = -ENXIO ; +else if (kvm->created_vcpus) + r = -EINVAL ; +else + kvm->arch.apic_bus_cycle_ns = bus_cycle_ns; +mutex_unlock (&kvm->lock); +break ; + }default : r = -EINVAL ;break ;
include/uapi/linux/kvm.h +1 -0
@@ -917,6 +917,7 @@ struct kvm_enable_cap {#define KVM_CAP_MEMORY_ATTRIBUTES 233#define KVM_CAP_GUEST_MEMFD 234#define KVM_CAP_VM_TYPES 235 +#define KVM_CAP_X86_APIC_BUS_FREQUENCY 236struct kvm_irq_routing_irqchip {__u32 irqchip;
Signature · 1 line
2.34.1
Re: [PATCH V4 3/4] KVM: x86: Add a capability to configure bus frequency for APIC timer
Quoted 59 lines · Reinette Chatre
From: Isaku Yamahata <[email protected]>
Add
KVM_CAP_X86_APIC_BUS_FREQUENCYcapability to configure the APIC bus clock frequency for APIC timer emulation.
AllowKVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY)to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf0x15to advertise the frequency.Vishal reported that the TDX guest kernel expects a 25MHz APIC bus frequency but ends up getting interrupts at a significantly higher rate.
The TDX architecture hard-codes the core crystal clock frequency to 25MHz and mandates exposing it via CPUID leaf
0x15. The TDX architecture does not allow the VMM to override the value.In addition, per Intel SDM:
"The APIC timer frequency will be the processor’s bus clock or core crystal clock frequency (when TSC/core crystal clock ratio is enumerated in CPUID leaf0x15) divided by the value specified in the divide configuration register."The resulting 25MHz APIC bus frequency conflicts with the KVM hardcoded APIC bus frequency of 1GHz.
The KVM doesn't enumerate CPUID leaf
0x15to the guest unless the user space VMM sets it usingKVM_SET_CPUID. If the CPUID leaf0x15is enumerated, the guest kernel uses it as the APIC bus frequency. If not, the guest kernel measures the frequency based on other known timers like the ACPI timer or the legacy PIT. As reported by Vishal the TDX guest kernel expects a 25MHz timer frequency but gets timer interrupt more frequently due to the 1GHz frequency used by KVM.To ensure that the guest doesn't have a conflicting view of the APIC bus frequency, allow the userspace to tell KVM to use the same frequency that TDX mandates instead of the default 1Ghz.
There are several options to address this:
1. Make the KVM able to configure APIC bus frequency (this series).
Pro: It resembles the existing hardware. The recent Intel CPUs adapts 25MHz.
Con: Require the VMM to emulate the APIC timer at 25MHz.
2. Make the TDX architecture enumerate CPUID leaf0x15to configurable frequency or not enumerate it.
Pro: Any APIC bus frequency is allowed.
Con: Deviates from TDX architecture.
3. Make the TDX guest kernel use 1GHz when it's running on KVM.
Con: The kernel ignores CPUID leaf0x15.
4. Change CPUID leaf0x15under TDX to report the crystal clock frequency as 1 GHz.
Pro: This has been the virtual APIC frequency for KVM guests for 13 years.
Pro: This requires changing only one hard-coded constant in TDX.
Con: It doesn't work with other VMMs as TDX isn't specific to KVM.
Con: Core crystal clock frequency is also used to calculate TSC frequency.
Con: If it is configured to value different from hardware, it will break the correctness of INTEL-PT Mini Time Count (MTC) packets in TDs.
Quoted 3 lines
Reported-by Vishal Annapurve <[email protected]>
Is Closes appropriate, given the issue Vishal hit was on non-upstream code?
Quoted 3 lines
Signed-off-by Isaku Yamahata <[email protected]>Co-developed-by Reinette Chatre <[email protected]>Signed-off-by Reinette Chatre <[email protected]>
Re: [PATCH V4 3/4] KVM: x86: Add a capability to configure bus frequency for APIC timer
Hi Rick,
Quoted 60 lines · Rick P
Quoted 59 lines · Reinette Chatre
From: Isaku Yamahata <[email protected]>
Add
KVM_CAP_X86_APIC_BUS_FREQUENCYcapability to configure the APIC bus clock frequency for APIC timer emulation.
AllowKVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY)to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf0x15to advertise the frequency.Vishal reported that the TDX guest kernel expects a 25MHz APIC bus frequency but ends up getting interrupts at a significantly higher rate.
The TDX architecture hard-codes the core crystal clock frequency to 25MHz and mandates exposing it via CPUID leaf
0x15. The TDX architecture does not allow the VMM to override the value.In addition, per Intel SDM:
"The APIC timer frequency will be the processor’s bus clock or core crystal clock frequency (when TSC/core crystal clock ratio is enumerated in CPUID leaf0x15) divided by the value specified in the divide configuration register."The resulting 25MHz APIC bus frequency conflicts with the KVM hardcoded APIC bus frequency of 1GHz.
The KVM doesn't enumerate CPUID leaf
0x15to the guest unless the user space VMM sets it usingKVM_SET_CPUID. If the CPUID leaf0x15is enumerated, the guest kernel uses it as the APIC bus frequency. If not, the guest kernel measures the frequency based on other known timers like the ACPI timer or the legacy PIT. As reported by Vishal the TDX guest kernel expects a 25MHz timer frequency but gets timer interrupt more frequently due to the 1GHz frequency used by KVM.To ensure that the guest doesn't have a conflicting view of the APIC bus frequency, allow the userspace to tell KVM to use the same frequency that TDX mandates instead of the default 1Ghz.
There are several options to address this:
1. Make the KVM able to configure APIC bus frequency (this series).
Pro: It resembles the existing hardware. The recent Intel CPUs adapts 25MHz.
Con: Require the VMM to emulate the APIC timer at 25MHz.
2. Make the TDX architecture enumerate CPUID leaf0x15to configurable frequency or not enumerate it.
Pro: Any APIC bus frequency is allowed.
Con: Deviates from TDX architecture.
3. Make the TDX guest kernel use 1GHz when it's running on KVM.
Con: The kernel ignores CPUID leaf0x15.
4. Change CPUID leaf0x15under TDX to report the crystal clock frequency as 1 GHz.
Pro: This has been the virtual APIC frequency for KVM guests for 13 years.
Pro: This requires changing only one hard-coded constant in TDX.
Con: It doesn't work with other VMMs as TDX isn't specific to KVM.
Con: Core crystal clock frequency is also used to calculate TSC frequency.
Con: If it is configured to value different from hardware, it will break the correctness of INTEL-PT Mini Time Count (MTC) packets in TDs.
Quoted 5 lines
Quoted 3 lines
Reported-by Vishal Annapurve <[email protected]>Is Closes appropriate, given the issue Vishal hit was on non-upstream code?
The issue that Vishal encountered was root-caused to the APIC bus frequency conflict between KVM and TDX that has not changed since the original report.
It would be great if this submission can get confirmation that this series addresses the issues encountered originally. From what I can tell there has not been any formal accept/reject of this solution (apart from agreeing that it is the right approach [1]) since the original report.
Reinette
[1] https://lore.kernel.org/lkml/CAGtprH8-jiC+wsy2LgmZimrRUT6kuntD6EJso2Mvx5Y42za9Dw@mail.gmail.com/
Re: [PATCH V4 3/4] KVM: x86: Add a capability to configure bus frequency for APIC timer
In reply to Reinette ChatreOn 3/22/2024 12:37 AM, Reinette Chatre wrote:
...
Documentation/virt/kvm/api.rst error/annotated fault. · line 8066
Quoted 9 lines
Documentation/virt/kvm/api.rst +1
-0@@ -8063,6 +8063,23 @@ error/annotated fault. See KVM_EXIT_MEMORY_FAULT for more information. +7.35 KVM_CAP_X86_APIC_BUS_FREQUENCY
As sean mentioned it previous comment, I would be the one prefers KVM_CAP_X86_APIC_BUS_CYCLES_NS
Depending on whether people get hung up on nanoseconds not being a "frequency", either KVM_CAP_X86_APIC_BUS_FREQUENCY or KVM_CAP_X86_APIC_BUS_CYCLES_NS.
PATCH v4 4/4 KVM: selftests: Add test for configure of x86 APIC bus frequency
In reply to Reinette ChatreFrom: Isaku Yamahata <[email protected]>
Test if the APIC bus clock frequency is the expected configured value.
Set APIC timer's initial count to the maximum value and busy wait for 100 msec (any value is okay) with TSC value. Read the APIC timer's "current count" to calculate the actual APIC bus clock frequency based on TSC frequency.
---
Changes v4:
- Rework changelog.
- Add Sean's "Suggested-by" to acknowledge guidance received in
https://lore.kernel.org/all/[email protected]/
- Add copyright.
- Add test description to file header.
- Consistent capitalization for acronyms.
- Rebase to kvm-x86/next.
- Update to v4 change of providing bus clock rate in nanoseconds.
- Add a "TEST_REQUIRE()" for the new capability so that the test can work on kernels that do not support the new capability.
- Address checkpatch warnings and use tabs instead of spaces in header file to match existing code.
Changes v3:
- Use 1.5GHz instead of 1GHz as frequency.
Changes v2:
- Newly added.
tools/testing/selftests/kvm/Makefile | 1 + .../selftests/kvm/include/x86_64/apic.h | 7 + .../kvm/x86_64/apic_bus_clock_test.c | 166 ++++++++++++++++++ 3 files changed, 174 insertions(+) create mode 100644 tools/testing/selftests/kvm/x86_64/apic_bus_clock_test.c
tools/testing/selftests/kvm/Makefile +1 -0
@@ -110,6 +110,7 @@ TEST_GEN_PROGS_x86_64 += x86_64/vmx_invalid_nested_guest_state TEST_GEN_PROGS_x86_64 += x86_64/vmx_set_nested_state_test TEST_GEN_PROGS_x86_64 += x86_64/vmx_tsc_adjust_test TEST_GEN_PROGS_x86_64 += x86_64/vmx_nested_tsc_scaling_test +TEST_GEN_PROGS_x86_64 += x86_64/apic_bus_clock_test TEST_GEN_PROGS_x86_64 += x86_64/xapic_ipi_test TEST_GEN_PROGS_x86_64 += x86_64/xapic_state_test TEST_GEN_PROGS_x86_64 += x86_64/xcr0_cpuid_test
tools/testing/selftests/kvm/include/x86_64/apic.h +7 -0
@@ -60,6 +60,13 @@#define APIC_VECTOR_MASK 0x000FF#define APIC_ICR2 0x310#define SET_APIC_DEST_FIELD (x) ((x) << 24) +#define APIC_LVT0 0x350 +#define APIC_LVT_TIMER_ONESHOT (0 << 17) +#define APIC_LVT_TIMER_PERIODIC (1 << 17) +#define APIC_LVT_TIMER_TSCDEADLINE (2 << 17) +#define APIC_TMICT 0x380 +#define APIC_TMCCT 0x390 +#define APIC_TDCR 0x3E0void apic_disable (void );void xapic_enable (void );
tools/testing/selftests/kvm/x86_64/apic_bus_clock_test.c new file +166 -0
166 lines not on this page · raw message
Signature · 1 line
2.34.1
Quoted 8 lines · Reinette Chatre
Summary
-------
AddKVM_CAP_X86_APIC_BUS_FREQUENCYcapability to configure the APIC bus clock frequency for APIC timer emulation.
AllowKVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY)to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf0x15to advertise the frequency.
Looks good to me and...
The only thing missing is actually integrating it into TDX qemu patches and testing the resulting TD. I think we are making a fair assumption that the problem should be resolved based on the analysis, but we have not actually tested that part. Is that right? What do you think?
Sean Christopherson
maintainerQuoted 10 lines · Rick P Edgecombe
Quoted 8 lines · Reinette Chatre
Summary
-------
AddKVM_CAP_X86_APIC_BUS_FREQUENCYcapability to configure the APIC bus clock frequency for APIC timer emulation.
AllowKVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY)to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf0x15to advertise the frequency.
Quoted 7 lines
Looks good to me and...
Tested-by Rick Edgecombe <[email protected]>The only thing missing is actually integrating it into TDX qemu patches and testing the resulting TD. I think we are making a fair assumption that the problem should be resolved based on the analysis, but we have not actually tested that part. Is that right?
Please tell me that Rick is wrong, and that this actually has been tested with a TDX guest. I don't care _who_ tested it, or with what VMM it has been tested, but _someone_ needs to verify that this actually fixes the TDX issue.
Quoted 19 lines · Sean Christopherson
Quoted 10 lines · Rick P Edgecombe
Quoted 8 lines · Reinette Chatre
Summary
-------
AddKVM_CAP_X86_APIC_BUS_FREQUENCYcapability to configure the APIC bus clock frequency for APIC timer emulation.
AllowKVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY)to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf0x15to advertise the frequency.Quoted 7 lines
Looks good to me and...
Tested-by Rick Edgecombe <[email protected]>The only thing missing is actually integrating it into TDX qemu patches and testing the resulting TD. I think we are making a fair assumption that the problem should be resolved based on the analysis, but we have not actually tested that part. Is that right?
Quoted 4 lines
Please tell me that Rick is wrong, and that this actually has been tested with a TDX guest. I don't care _who_ tested it, or with what VMM it has been tested,
but _someone_ needs to verify that this actually fixes the TDX issue.
It is in the process of getting a TDX test developed (or rather updated). Agreed, it requires verification that it fixes the original TDX issue. That is why I raised it.
Reinette was working on this internally and some iterations were happening, but we are trying to work on the public list as much as possible per your earlier comments. So that is why she posted it.
There was at least some level of TDX integration in the past. I'm not sure what exactly was tested, but we are going to re-verify it with the latest everything.
Sean Christopherson
maintainerQuoted 24 lines · Rick P Edgecombe
Quoted 14 lines · Sean Christopherson
Quoted 13 lines · Rick P Edgecombe
Quoted 8 lines · Reinette Chatre
Summary
-------
AddKVM_CAP_X86_APIC_BUS_FREQUENCYcapability to configure the APIC bus clock frequency for APIC timer emulation.
AllowKVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY)to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf0x15to advertise the frequency.Looks good to me and...
Tested-by Rick Edgecombe <[email protected]>Quoted 8 lines
Quoted 4 lines
The only thing missing is actually integrating it into TDX qemu patches and testing the resulting TD. I think we are making a fair assumption that the problem should be resolved based on the analysis, but we have not actually tested that part. Is that right?
Please tell me that Rick is wrong, and that this actually has been tested with a TDX guest. I don't care _who_ tested it, or with what VMM it has been tested, but _someone_ needs to verify that this actually fixes the TDX issue.
Quoted 7 lines
It is in the process of getting a TDX test developed (or rather updated). Agreed, it requires verification that it fixes the original TDX issue. That is why I raised it.
Reinette was working on this internally and some iterations were happening, but we are trying to work on the public list as much as possible per your earlier comments. So that is why she posted it.
I have no problem posting "early", but Documentation/process/maintainer-kvm-x86.rst clearly states under Testing that:
If you can't fully test a change, e.g. due to lack of hardware, clearly state what level of testing you were able to do, e.g. in the cover letter.
I was assuming that this was actually *fully* tested, because nothing suggests otherwise. And _that_ is a problem, e.g. I was planning on applying this series for 6.10, which would have made for quite the mess if it turns out that this doesn't actually solve the TDX problem.
Quoted 2 lines
There was at least some level of TDX integration in the past. I'm not sure what exactly was tested, but we are going to re-verify it with the latest everything.
Honest question, is it a big lift to re-test the QEMU+KVM TDX changes, e.g. to verify this new capability actually does what we hope it does? If testing is a big lift, what are the pain points? Or perhaps a better question is, is there anything we (both upstream people, and end users like Google) can do to make re-testing less awful?
+Vishal
Quoted 8 lines · Sean Christopherson
I have no problem posting "early", but
Documentation/process/maintainer-kvm-x86.rst
clearly states under Testing that:If you can't fully test a change, e.g. due to lack of hardware, clearly state
what level of testing you were able to do, e.g. in the cover letter.
Quoted 5 lines
I was assuming that this was actually *fully* tested, because nothing suggests otherwise. And _that_ is a problem, e.g. I was planning on applying this series
for 6.10, which would have made for quite the mess if it turns out that this doesn't actually solve the TDX problem.
Ok, sorry. Will definitely be clear about this in the future. There is a little bit of chaos on our end right now as new people spin up and we adjust our working model to be more upstream focused. Thanks for being clear.
Yes, please don't apply until we have the full testing done. It may not be far away though, per Reinette.
Quoted 6 lines
Quoted 5 lines
There was at least some level of TDX integration in the past. I'm not sure what
exactly was tested, but we are going to re-verify it with the latest everything.
Quoted 6 lines
Honest question, is it a big lift to re-test the QEMU+KVM TDX changes, e.g. to verify this new capability actually does what we hope it does? If testing is a
big lift, what are the pain points? Or perhaps a better question is, is there anything we (both upstream people, and end users like Google) can do to make re-testing less awful?
I wouldn't say a big lift, but probably more than usual. Most of the testing challenges come from updating and matching specific, often out of tree components. We need to have specific OVMF, TDX module, QEMU, KVM core patches, KVM breakout series, and tests versions that all match.
To wrangle it, automated testing is something we are working on internally right now. I can't think of anything to ask of upstream specifically. But Vishal might.
As for Google, the TDX selftests are useful. We need to update them ourselves to keep up with uAPI changes. We could do a little more co-development on those? As in, not wait until we post new versions to get updates from Google's side. Just an idea off the top of my head.
As for the TDX kvm unit tests updates [0]. They have not had much review. I think we maybe have enough TDX patches to focus on already though.
Long term though, I have been wondering about how to prevent TDX regressions especially on the MMU pieces. It is one thing to have the TDX setups available for maintainers, but most normal developers will likely not have access to TDX HW for a bit. Just a problem without a solution.
Sean Christopherson
maintainerQuoted 4 lines · Rick P Edgecombe
Long term though, I have been wondering about how to prevent TDX regressions especially on the MMU pieces. It is one thing to have the TDX setups available for maintainers, but most normal developers will likely not have access to TDX HW for a bit. Just a problem without a solution.
I wouldn't worry too much about hardware availability. As you said, it's not a problem we can really solve, and we already have to be concious of the fact that not all developers have comparable hardware. E.g. most people don't have a 4-sock, multi-hundred CPU system with TiBs of RAM. Not being able to test at all is obviously a little different, but it's not entirely new.
Instead, I would encourage spending time and effort (after things have settled
down patch wise) to build out selftests. I tried to run a "real" SEV-ES VM
and gave up because I needed the "right" OVMF build, blah blah blah. At some point I'll probably bite the bullet and get a "full" CoCo setup working, but it's not exactly at the top of my todo list, in no small part because the triage and debug experience when things go wrong is miles and miles better in selftests.
Hi Sean,
Quoted 36 lines · Sean Christopherson
Quoted 24 lines · Rick P Edgecombe
Quoted 14 lines · Sean Christopherson
Quoted 13 lines · Rick P Edgecombe
Quoted 8 lines · Reinette Chatre
Summary
-------
AddKVM_CAP_X86_APIC_BUS_FREQUENCYcapability to configure the APIC bus clock frequency for APIC timer emulation.
AllowKVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY)to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf0x15to advertise the frequency.Looks good to me and...
Tested-by Rick Edgecombe <[email protected]>Quoted 8 lines
Quoted 4 lines
The only thing missing is actually integrating it into TDX qemu patches and testing the resulting TD. I think we are making a fair assumption that the problem should be resolved based on the analysis, but we have not actually tested that part. Is that right?
Please tell me that Rick is wrong, and that this actually has been tested with a TDX guest. I don't care _who_ tested it, or with what VMM it has been tested, but _someone_ needs to verify that this actually fixes the TDX issue.
Quoted 7 lines
It is in the process of getting a TDX test developed (or rather updated). Agreed, it requires verification that it fixes the original TDX issue. That is why I raised it.
Reinette was working on this internally and some iterations were happening, but we are trying to work on the public list as much as possible per your earlier comments. So that is why she posted it.
I have no problem posting "early", but
Documentation/process/maintainer-kvm-x86.rstclearly states under Testing that:
Quoted 7 lines
If you can't fully test a change, e.g. due to lack of hardware, clearly state what level of testing you were able to do, e.g. in the cover letter.
I was assuming that this was actually *fully* tested, because nothing suggests otherwise. And _that_ is a problem, e.g. I was planning on applying this series for 6.10, which would have made for quite the mess if it turns out that this doesn't actually solve the TDX problem.
There was one vote for the capability name to rather be KVM_CAP_X86_APIC_BUS_CYCLES_NS [1]
I'd be happy to resubmit with the name changed but after reading your statement above it is not clear to me what name is preferred: KVM_CAP_X86_APIC_BUS_FREQUENCY as used in this series that seem to meet your approval or KVM_CAP_X86_APIC_BUS_CYCLES_NS.
Please let me know what you prefer.
Thank you.
Reinette
Sean Christopherson
maintainerQuoted 8 lines · Reinette Chatre
There was one vote for the capability name to rather be
KVM_CAP_X86_APIC_BUS_CYCLES_NS[1]I'd be happy to resubmit with the name changed but after reading your statement above it is not clear to me what name is preferred:
KVM_CAP_X86_APIC_BUS_FREQUENCYas used in this series that seem to meet your approval orKVM_CAP_X86_APIC_BUS_CYCLES_NS.Please let me know what you prefer.
Both work for me, I don't have a strong preference.
Hi Sean,
Quoted 11 lines · Sean Christopherson
Quoted 8 lines · Reinette Chatre
There was one vote for the capability name to rather be
KVM_CAP_X86_APIC_BUS_CYCLES_NS[1]I'd be happy to resubmit with the name changed but after reading your statement above it is not clear to me what name is preferred:
KVM_CAP_X86_APIC_BUS_FREQUENCYas used in this series that seem to meet your approval orKVM_CAP_X86_APIC_BUS_CYCLES_NS.Please let me know what you prefer.
Both work for me, I don't have a strong preference.
Thank you. I'll resubmit with the capability name changed to KVM_CAP_X86_APIC_BUS_CYCLES_NS. This is the only planned change.
Reinette
(+Yao Yuan)
Hi Sean and Rick,
Quoted 29 lines · Rick P
Quoted 19 lines · Sean Christopherson
Quoted 10 lines · Rick P Edgecombe
Quoted 8 lines · Reinette Chatre
Summary
-------
AddKVM_CAP_X86_APIC_BUS_FREQUENCYcapability to configure the APIC bus clock frequency for APIC timer emulation.
AllowKVM_ENABLE_CAPABILITY(KVM_CAP_X86_APIC_BUS_FREQUENCY)to set the frequency in nanoseconds. When using this capability, the user space VMM should configure CPUID leaf0x15to advertise the frequency.Quoted 7 lines
Looks good to me and...
Tested-by Rick Edgecombe <[email protected]>The only thing missing is actually integrating it into TDX qemu patches and testing the resulting TD. I think we are making a fair assumption that the problem should be resolved based on the analysis, but we have not actually tested that part. Is that right?
Quoted 4 lines
Please tell me that Rick is wrong, and that this actually has been tested with a TDX guest. I don't care _who_ tested it, or with what VMM it has been tested,
but _someone_ needs to verify that this actually fixes the TDX issue.It is in the process of getting a TDX test developed (or rather updated). Agreed, it requires verification that it fixes the original TDX issue. That is why I raised it.
Quoted 6 lines
Reinette was working on this internally and some iterations were happening, but we are trying to work on the public list as much as possible per your earlier comments. So that is why she posted it.
There was at least some level of TDX integration in the past. I'm not sure what exactly was tested, but we are going to re-verify it with the latest everything.
Apologies for the delay. I am the one needing to do this testing and it took me a while to ramp up on all the parts (and I am still learning).
I encountered quite the roadblock (for me) along the way that was caused by a lingering timer (presumably left by TDVF). Thank you so much to Isaku and Yao Yuan for helping me to root cause this. I believe that this is unique to the kvm-unit-tests that does not reset the environment like the OS.
A modified x86/apic.c:test_apic_timer_one_shot() was used to test this feature. Below I provide the diff of essential parts against
https://github.com/intel/kvm-unit-tests-tdx/blob/tdx/x86/apic.c for your reference. With these modifications it can be confirmed that the test within a TD fails without the work in this series, and passes with it. This was tested against a host kernel running a snapshot of the ongoing KVM TDX work and corresponding QEMU changes (including a QEMU change that enables the new capability introduced in this series).
Below are the core changes made to the existing APIC test. The two major changes are:
(a) stop any lingering timers before the test starts, (b) use CPUID 0x15 in TDX to accurately determine the TSC and APIC frequencies instead of making 1GHz assumption and use similar check as the kselftest test introduced in this series (I did have to increase the amount with which the frequency is allowed to deviate by 1% in my testing).
Please note that there are some more changes needed to run this test in TDX since all APIC tests are not appropriate for TDX. This snippet was used in my testing and I will work with kvm-unit-test folks on the next steps to have it integrated.
@@ -477,11 +478,29 @@ static void lvtt_handler(isr_regs_t *regs)
static void test_apic_timer_one_shot(void)
{
- uint64_t tsc1, tsc2;
static const uint32_t interval = 0x10000;
+ uint64_t measured_apic_freq, tsc2, tsc1;
+ uint32_t tsc_freq = 0, apic_freq = 0;
+ struct cpuid cpuid_tsc = {};
#define APIC_LVT_TIMER_VECTOR (0xee)
+ /*
+ * CPUID 0x15 is not available in VMX, can use it to obtain
+ * TSC and APIC frequency for accurate testing
+ */
+ if (is_tdx_guest()) {
+ cpuid_tsc = raw_cpuid(0x15, 0);
+ tsc_freq = cpuid_tsc.c * cpuid_tsc.b / cpuid_tsc.a;
+ apic_freq = cpuid_tsc.c;
+ }
+ /*
+ stop already fired local timer + the test case can be negative failure if the timer fired + after installed lvtt_handler but *before* + write to TIMICT again.
+ */
+ apic_write(APIC_TMICT, 0);
handle_irq(APIC_LVT_TIMER_VECTOR, lvtt_handler);
/* One shot mode */
@@ -503,8 +522,16 @@ static void test_apic_timer_one_shot(void)
* cases, the following should satisfy on all modern
* processors.
*/
- report((lvtt_counter == 1) && (tsc2 - tsc1 >= interval),
- "APIC LVT timer one shot");
+ if (is_tdx_guest()) {
+ measured_apic_freq = interval * (tsc_freq / (tsc2 - tsc1));
+ report((lvtt_counter == 1) &&
+ (measured_apic_freq < apic_freq * 102 / 100) && + (measured_apic_freq > apic_freq * 98 / 100), + "APIC LVT timer one shot");
+ } else {
+ report((lvtt_counter == 1) && (tsc2 - tsc1 >= interval),
+ "APIC LVT timer one shot");
+ }
}
Reinette