Boot #4 and source on ftp site
Quoted 7 lines
Quoted 7 lines
So my question is how to place built "ipl" binary at the appropriate place on the disk so that PDC finds it. Any magic combination of commands ? Looks like I am missing something obvious.
Quoted 9 lines
Quoted 3 lines
Thanks in advance,
-pkd
You are on the right track. After lifinit you have to use lifcp to copy the file into the newly created LIF volume. You also have to give it the correct file type. A script I use for creating bootable LIF volumes looks something like:
That is one way. The way I do it for our very simple LIF volume is as folows:
Once you have obtained the SOM ipl binary (after make), then:
% strip ipl
% mkipl ipl
% mklifhdr hdr x y z a b c (see the utility for what these #'s mean) % cat hdr pad_file ipl vmlinux > bootstrap.bin
pad_file is a 1024 byte file full of 0.
I did forget to put this information into the README, sorry. Eventually (next few days, hopefully), there will be one utility "mkimg" that will automatically do everything above for you (particularly, picking the numbers which have to do with entry points, etc).
Of course, vmlinux doesn't yet exist. I just have a simple dummy kernel I use there, which hasn't been included in the distribution. If you want to play around without the dummy kernel, just comment out the line in ipl_c.c that branches to the kernel and remove "vmlinux" from the concat line step above. You can then see the bootstrap run, but it won't try to execute the kernel.
Have fun, Jason.
OK, in the spirit of Linux tradition, I was able to hack it to finally work. After doing couple of hex dumps of given bootstrap.bin :-) and realizing what was I doing wrong.
Also I forgot to see the boot_utils directory.
So it also works on a B class 180. All that we need now is a Vmlinux.
Your answer explains why I am not seeing the moving cursor. I Did not add a dummy kernel to image.
Any reasons you included libmilli.a in Makefile ? Since I was getting bad archive messages I took it out of Makefile. Does not seem to affect anything.
Keep up the good work.
Cheers,
pkd
Quoted 47 lines · Jason Eckhardt
Quoted 7 lines
Quoted 7 lines
So my question is how to place built "ipl" binary at the appropriate place on the disk so that PDC finds it. Any magic combination of commands ? Looks like I am missing something obvious.
Quoted 9 lines
Quoted 3 lines
Thanks in advance,
-pkd
You are on the right track. After lifinit you have to use lifcp to copy the file into the newly created LIF volume. You also have to give it the correct file type. A script I use for creating bootable LIF volumes looks something like:
That is one way. The way I do it for our very simple LIF volume is as folows:
Once you have obtained the SOM ipl binary (after make), then:
% strip ipl
% mkipl ipl
% mklifhdr hdr x y z a b c (see the utility for what these #'s mean) % cat hdrpad_fileipl vmlinux > bootstrap.bin
pad_fileis a 1024 byte file full of 0.I did forget to put this information into the README, sorry. Eventually (next few days, hopefully), there will be one utility "mkimg" that will automatically do everything above for you (particularly, picking the numbers which have to do with entry points, etc).
Of course, vmlinux doesn't yet exist. I just have a simple dummy kernel I use there, which hasn't been included in the distribution. If you want to play around without the dummy kernel, just comment out the line in
ipl_c.cthat branches to the kernel and remove "vmlinux" from the concat line step above. You can then see the bootstrap run, but it won't try to execute the kernel.Have fun, Jason.
-------------------------------------------------------------------------
To unsubscribe: send e-mail to [email protected] with `unsubscribe' as the subject.