configs: defconfig for Sipeed Maix in S-mode
PATCH v2 1/1 configs: defconfig for Sipeed Maix in S-mode
Provide a defconfig that can be used to build U-Boot for the Maix boards running upon OpenSBI.
Update the documentation.
Signed-off-by Heinrich Schuchardt <[email protected]>
---
v2:
adjust MAINTAINERS
--- board/sipeed/maix/MAINTAINERS | 2 +- configs/sipeed_maix_smode_defconfig | 10 ++++++ doc/board/sipeed/maix.rst | 49 +++++++++++++++++++++++++++++ 3 files changed, 60 insertions(+), 1 deletion(-) create mode 100644 configs/sipeed_maix_smode_defconfig
board/sipeed/maix/MAINTAINERS +1 -1
@@ -4,7 +4,7 @@ S: Maintained F: arch/riscv/dts/k210.dtsi F: arch/riscv/dts/k210-maix-bit.dts F: board/sipeed/maix/ -F: configs/sipeed_maix_bitm_defconfig +F: configs/sipeed_maix*_defconfig F: doc/board/sipeed/ F: include/configs/sipeed-maix.h F: include/dt-bindings/*/k210-sysctl.h
configs/sipeed_maix_smode_defconfig new file +10 -0
@@ -0,0 +1,10 @@ +CONFIG_RISCV=y +CONFIG_SYS_TEXT_BASE=0x80020000 +CONFIG_TARGET_SIPEED_MAIX=y +CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_STACK_SIZE=0x100000 +# CONFIG_NET is not set +# CONFIG_INPUT is not set +# CONFIG_DM_ETH is not set +# CONFIG_EFI_UNICODE_CAPITALIZATION is not set
doc/board/sipeed/maix.rst +49 -0
58 lines not on this page · raw message
--
2.28.0
PATCH v2 1/1 configs: defconfig for Sipeed Maix in S-mode
Quoted 10 lines · Heinrich Schuchardt
Provide a defconfig that can be used to build U-Boot for the Maix boards running upon OpenSBI.
Update the documentation.
Signed-off-by Heinrich Schuchardt <[email protected]>---
v2:
adjustMAINTAINERS
Quoted 7 lines
--- board/sipeed/maix/MAINTAINERS | 2 +- configs/sipeed_maix_smode_defconfig | 10 ++++++ doc/board/sipeed/maix.rst | 49 +++++++++++++++++++++++++++++ 3 files changed, 60 insertions(+), 1 deletion(-) create mode 100644 configs/sipeed_maix_smode_defconfig
Reviewed-by Bin Meng <[email protected]>
PATCH v2 1/1 configs: defconfig for Sipeed Maix in S-mode
In reply to Heinrich SchuchardtQuoted 110 lines · Heinrich Schuchardt
Provide a defconfig that can be used to build U-Boot for the Maix boards running upon OpenSBI.
Update the documentation.
Signed-off-by Heinrich Schuchardt <[email protected]>---
v2:
adjustMAINTAINERS--- board/sipeed/maix/MAINTAINERS | 2 +- configs/sipeed_maix_smode_defconfig | 10 ++++++ doc/board/sipeed/maix.rst | 49 +++++++++++++++++++++++++++++ 3 files changed, 60 insertions(+), 1 deletion(-) create mode 100644 configs/sipeed_maix_smode_defconfigboard/sipeed/maix/MAINTAINERS +1
-1@@ -4,7 +4,7 @@ S: Maintained F: arch/riscv/dts/k210.dtsi F: arch/riscv/dts/k210-maix-bit.dts F: board/sipeed/maix/ -F: configs/sipeed_maix_bitm_defconfig +F: configs/sipeed_maix*_defconfig F: doc/board/sipeed/ F: include/configs/sipeed-maix.h F: include/dt-bindings/*/k210-sysctl.hconfigs/sipeed_maix_smode_defconfig new file +10
-0@@ -0,0 +1,10 @@ +CONFIG_RISCV=y +CONFIG_SYS_TEXT_BASE=0x80020000 +CONFIG_TARGET_SIPEED_MAIX=y +CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_STACK_SIZE=0x100000 +# CONFIG_NET is not set +# CONFIG_INPUT is not set +# CONFIG_DM_ETH is not set +# CONFIG_EFI_UNICODE_CAPITALIZATION is not setdoc/board/sipeed/maix.rst +49
-1@@ -75,6 +75,49 @@ console shall be opened immediately. Boot output should look like the following: Err: serial at 38000000 => +OpenSBI +^^^^^^^ + +OpenSBI is an open source supervisor execution environment implementing the +RISC-V Supervisor Binary Interface Specification [1]. One of its features is +to intercept run-time exceptions, e.g. for unaligned access or illegal +instructions, and to emulate the failing instructions. + +The OpenSBI source can be downloaded via: + +.. code-block:: bash + + git clone https://github.com/riscv/opensbi + +As OpenSBI will be loaded at 0x80000000 we have to adjust the U-Boot text base. +Furthermore we have to enable building U-Boot for S-mode:: + + CONFIG_SYS_TEXT_BASE=0x80020000 + CONFIG_RISCV_SMODE=y + +Both settings are contained in sipeed_maix_smode_defconfig so we can build +U-Boot with: + +.. code-block:: bash + + make sipeed_maix_smode_defconfig + make + +To build OpenSBI with U-Boot as a payload: + +.. code-block:: bash + + cd opensbi + make \ + PLATFORM=kendryte/k210 \ + FW_PAYLOAD=y \ + FW_PAYLOAD_OFFSET=0x20000 \ + FW_PAYLOAD_PATH=<path to U-Boot>/u-boot-dtb.bin + +The value of FW_PAYLOAD_OFFSET must match CONFIG_SYS_TEXT_BASE - 0x80000000. + +The file to flash is build/platform/kendryte/k210/firmware/fw_payload.bin. + Loading Images ^^^^^^^^^^^^^^@@ -363,3 +406,9 @@ Address Size Description interrupts) 0x8801f000 0x1000 credits ========== ========= =========== + +Links +----- + +[1] https://github.com/riscv/riscv-sbi-doc + RISC-V Supervisor Binary Interface Specification --
Quoted 2 lines
2.28.0
Reviewed-by Sean Anderson <[email protected]>