riscv: Add SPI support for Kendryte K210
Subsystems (3)
cover riscv: Add SPI support for Kendryte K210
This patch adds support for SPI on the Kendryte K210. This includes the MMC slot and SPI flash on the Sipeed Maix Bit.
This patch series was previously part of
https://patchwork.ozlabs.org/project/uboot/list/?series=161576
This patch series depends on
https://patchwork.ozlabs.org/project/uboot/list/?series=162646
Known bugs:
- The MMC cannot be accessed with the dw_spi driver
Sean Anderson (8):
doc: Fix typo in FIT documentation
spi: dw: Add device tree properties for fields in CTRL0
spi: dw: Rename "cs-gpio" to "cs-gpios"
spi: dw: Use generic function to read reg address
spi: dw: Speed up transfer loops
spi: dw: Add mem_ops
riscv: Add device tree bindings for SPI
riscv: Add support for SPI on Kendryte K210
arch/arc/dts/axs10x_mb.dtsi | 3 +- arch/arc/dts/hsdk.dts | 3 +- arch/riscv/dts/k210-maix-bit.dts | 90 ++++++++ arch/riscv/dts/k210.dtsi | 12 + board/sipeed/maix/Kconfig | 10 + configs/sipeed_maix_bitm_defconfig | 8 + doc/board/sipeed/maix.rst | 94 +++++--- .../spi/snps,dw-apb-ssi.txt | 43 ++++ doc/uImage.FIT/source_file_format.txt | 2 +- drivers/spi/designware_spi.c | 211 ++++++++++++++---- 10 files changed, 395 insertions(+), 81 deletions(-) create mode 100644 doc/device-tree-bindings/spi/snps,dw-apb-ssi.txt
Signature · 1 line
2.25.0
PATCH 1/8 doc: Fix typo in FIT documentation
u_boot should be u-boot
---
doc/uImage.FIT/source_file_format.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
doc/uImage.FIT/source_file_format.txt +1 -1
@@ -172,7 +172,7 @@ the '/images' node should have the following layout: - os : OS name, mandatory for types "kernel" and "ramdisk". Valid OS names are: "openbsd", "netbsd", "freebsd", "4_4bsd", "linux", "svr4", "esix", "solaris", "irix", "sco", "dell", "ncr", "lynxos", "vxworks", "psos", "qnx", - "u_boot", "rtems", "unity", "integrity". + "u-boot", "rtems", "unity", "integrity". - arch : Architecture name, mandatory for types: "standalone", "kernel", "firmware", "ramdisk" and "fdt". Valid architecture names are: "alpha", "arm", "i386", "ia64", "mips", "mips64", "ppc", "s390", "sh", "sparc",
Signature · 1 line
2.25.0
PATCH 1/8 doc: Fix typo in FIT documentation
Quoted 14 lines · Sean Anderson
u_bootshould be u-bootSigned-off-by Sean Anderson <[email protected]>Reviewed-by Bin Meng <[email protected]>---
doc/uImage.FIT/source_file_format.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)doc/uImage.FIT/source_file_format.txt +0
-0
doc/uImage.FIT/source_file_format.txt the '/images' node should have the following layout: · line 175
Quoted 5 lines
doc/uImage.FIT/source_file_format.txt +1
-1@@ -172,7 +172,7 @@ the '/images' node should have the following layout: - os : OS name, mandatory for types "kernel" and "ramdisk". Valid OS names are: "openbsd", "netbsd", "freebsd", "4_4bsd", "linux", "svr4", "esix", "solaris", "irix", "sco", "dell", "ncr", "lynxos", "vxworks", "psos", "qnx", - "u_boot", "rtems", "unity", "integrity". + "u-boot", "rtems", "unity", "integrity".
I wonder why 4_4bsd in that list is also spelled with an underscore ?
PATCH 1/8 doc: Fix typo in FIT documentation
Quoted 10 lines · Marek Vasut
Quoted 9 lines · Sean Anderson
u_bootshould be u-bootSigned-off-by Sean Anderson <[email protected]>Reviewed-by Bin Meng <[email protected]>---
doc/uImage.FIT/source_file_format.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Quoted 12 lines
doc/uImage.FIT/source_file_format.txt the '/images' node should have the following layout: · line 175
Quoted 10 lines
doc/uImage.FIT/source_file_format.txt +1
-1@@ -172,7 +172,7 @@ the '/images' node should have the following layout: - os : OS name, mandatory for types "kernel" and "ramdisk". Valid OS names are: "openbsd", "netbsd", "freebsd", "4_4bsd", "linux", "svr4", "esix", "solaris", "irix", "sco", "dell", "ncr", "lynxos", "vxworks", "psos", "qnx", - "u_boot", "rtems", "unity", "integrity". + "u-boot", "rtems", "unity", "integrity".I wonder why 4_4bsd in that list is also spelled with an underscore ?
Matches the code:common/image.c: { IH_OS_4_4BSD, "4_4bsd", "4_4BSD", },
Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200323/6df09482/attachment.sig>
PATCH 2/8 spi: dw: Add device tree properties for fields in CTRL0
In reply to Sean AndersonSome devices have different layouts for the fields in CTRL0 (e.g. the Kendryte K210). Allow this layout to be configurable from the device tree. The documentation has been taken from Linux.
---
.../spi/snps,dw-apb-ssi.txt | 43 +++++++++++++++++++ drivers/spi/designware_spi.c | 40 ++++++++++------- 2 files changed, 68 insertions(+), 15 deletions(-) create mode 100644 doc/device-tree-bindings/spi/snps,dw-apb-ssi.txt
doc/device-tree-bindings/spi/snps,dw-apb-ssi.txt new file +43 -0
@@ -0,0 +1,43 @@ +Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. + +Required properties: +- compatible : "snps,dw-apb-ssi" +- reg : The register base for the controller. For "mscc,<soc>-spi", a second + register set is required (named ICPU_CFG:SPI_MST) +- #address-cells : <1>, as required by generic SPI binding. +- #size-cells : <0>, also as required by generic SPI binding. +- clocks : phandles for the clocks, see the description of clock-names below. + The phandle for the "ssi_clk" is required. The phandle for the "pclk" clock + is optional. If a single clock is specified but no clock-name, it is the + "ssi_clk" clock. If both clocks are listed, the "ssi_clk" must be first. + +Optional properties: +- clock-names : Contains the names of the clocks: + "ssi_clk", for the core clock used to generate the external SPI clock. + "pclk", the interface clock, required for register access. +- cs-gpios : Specifies the gpio pins to be used for chipselects. +- num-cs : The number of chipselects. If omitted, this will default to 4. +- reg-io-width : The I/O register width (in bytes) implemented by this + device. Supported values are 2 or 4 (the default). +- snps,dfs-offset The offset in bits of the DFS field in CTRL0, defaulting to 0 +- snps,frf-offset The offset in bits of the FRF field in CTRL0, defaulting to 4 +- snps,tmod-offset The offset in bits of the tmode field in CTRL0, defaulting + to 6 +- snps,mode-offset The offset in bits of the work mode field in CTRL0, + defaulting to 8 + +Child nodes as per the generic SPI binding. + +Example: + + spi at fff00000 { + compatible = "snps,dw-apb-ssi"; + reg = <0xfff00000 0x1000>; + interrupts = <0 154 4>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&spi_m_clk>; + num-cs = <2>; + cs-gpios = <&gpio0 13 0>, + <&gpio0 14 0>; + };
drivers/spi/designware_spi.c +25 -15
@@ -3,6 +3,7 @@* Designware master SPI core controller driver * * Copyright (C) 2014 Stefan Roese <[email protected]> +* Copyright (C) 2020 Sean Anderson <[email protected]> * * Very loosely based on the Linux driver: * drivers/spi/spi-dw.c, which is:
@@ -51,20 +52,14 @@#define DW_SPI_DR 0x60/* Bit fields in CTRLR0 */ -#define SPI_DFS_OFFSET 0 - -#define SPI_FRF_OFFSET 4#define SPI_FRF_SPI 0x0#define SPI_FRF_SSP 0x1#define SPI_FRF_MICROWIRE 0x2#define SPI_FRF_RESV 0x3 -#define SPI_MODE_OFFSET 6 -#define SPI_SCPH_OFFSET 6 -#define SPI_SCOL_OFFSET 7 +#define SPI_MODE_SCPH 0x1 +#define SPI_MODE_SCOL 0x2 -#define SPI_TMOD_OFFSET 8 -#define SPI_TMOD_MASK (0x3 << SPI_TMOD_OFFSET)#define SPI_TMOD_TR 0x0/* xmit & recv */ #define SPI_TMOD_TO 0x1/* xmit only */ #define SPI_TMOD_RO 0x2/* recv only */
@@ -89,6 +84,12 @@struct dw_spi_platdata {s32 frequency;/* Default clock frequency, -1 for none */ void __iomem *regs; + +/* Offsets in CTRL0 */ +u8 dfs_off; +u8 frf_off; +u8 tmod_off; +u8 mode_off; };struct dw_spi_priv {
@@ -115,6 +116,15 @@ struct dw_spi_priv {struct reset_ctl_bulk resets; }; +static inline u32 GEN_CTRL0 (struct dw_spi_priv *priv, +struct dw_spi_platdata *plat) +{ +return ((priv->bits_per_word -1 ) << plat->dfs_off | + (priv->type << plat->frf_off) | + (priv->mode << plat->mode_off) | + (priv->tmode << plat->tmod_off)); +} +static inline u32 dw_read (struct dw_spi_priv *priv,u32 offset) {return __raw_readl (priv->regs + offset);
@@ -160,6 +170,10 @@ static int dw_spi_ofdata_to_platdata(struct udevice *bus)/* Use 500KHz as a suitable default */ plat->frequency =dev_read_u32_default (bus,"spi-max-frequency" ,500000 ); + plat->dfs_off =dev_read_u32_default (bus,"snps,dfs-offset" ,0 ); + plat->frf_off =dev_read_u32_default (bus,"snps,frf-offset" ,4 ); + plat->mode_off =dev_read_u32_default (bus,"snps,mode-offset" ,6 ); + plat->tmod_off =dev_read_u32_default (bus,"snps,tmod-offset" ,8 );debug ("%s: regs=%p max-frequency=%d\n" , __func__, plat->regs, plat->frequency);
@@ -388,6 +402,7 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen, const void *dout, void *din, unsigned long flags) { struct udevice *bus = dev->parent; +struct dw_spi_platdata *plat =dev_get_platdata (bus);struct dw_spi_priv *priv =dev_get_priv (bus);const u8 *tx = dout;u8 *rx = din;
@@ -406,10 +421,6 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen,if (flags &SPI_XFER_BEGIN )external_cs_manage (dev, false); - cr0 = (priv->bits_per_word -1 ) | (priv->type <<SPI_FRF_OFFSET ) | - (priv->mode <<SPI_MODE_OFFSET ) | - (priv->tmode <<SPI_TMOD_OFFSET ); -if (rx && tx) priv->tmode =SPI_TMOD_TR ;else if (rx)
@@ -421,8 +432,7 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen,*/ priv->tmode =SPI_TMOD_TR ; - cr0 &= ~SPI_TMOD_MASK ; - cr0 |= (priv->tmode <<SPI_TMOD_OFFSET ); + cr0 =GEN_CTRL0 (priv, plat); priv->len = bitlen >>3 ;debug ("%s: rx=%p tx=%p len=%d [bytes]\n" , __func__, rx, tx, priv->len);
@@ -476,7 +486,7 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen,static int dw_spi_set_speed (struct udevice *bus,uint speed) { -struct dw_spi_platdata *plat = bus->platdata; +struct dw_spi_platdata *plat =dev_get_platdata (bus);struct dw_spi_priv *priv =dev_get_priv (bus);u16 clk_div;
Signature · 1 line
2.25.0
PATCH 2/8 spi: dw: Add device tree properties for fields in CTRL0
Quoted 6 lines · Sean Anderson
Some devices have different layouts for the fields in CTRL0 (e.g. the Kendryte K210). Allow this layout to be configurable from the device tree. The documentation has been taken from Linux.
Signed-off-by Sean Anderson <[email protected]>Reviewed-by Simon Glass <[email protected]>
Can't you just have different compatible string for each SoC and derive the various fields based on that compatible string, instead of describing all the register bitfields in DT ?
What does Linux do ?
PATCH 2/8 spi: dw: Add device tree properties for fields in CTRL0
Quoted 5 lines · Marek Vasut
Quoted 4 lines · Sean Anderson
Some devices have different layouts for the fields in CTRL0 (e.g. the Kendryte K210). Allow this layout to be configurable from the device tree. The documentation has been taken from Linux.
Quoted 9 lines
Quoted 2 lines
Signed-off-by Sean Anderson <[email protected]>Reviewed-by Simon Glass <[email protected]>Can't you just have different compatible string for each SoC and derive the various fields based on that compatible string, instead of describing all the register bitfields in DT ?
What does Linux do ?
Linux only supports socfpga boards. I don't know if there is any rhyme/reason to the shifting around of these fields. It is possible to add several compatible strings like "kendryte,k210-spi3". I chose this method because the bitfields are different for spi0 and spi1, spi2, and spi3. If there are other incompatibilities discovered, then it may make more sense to use different strings. Another option could have been to use the DW_SPI_VERSION field to detect different controllers, but it is the same among all the controllers on the K210.
--Sean
PATCH 2/8 spi: dw: Add device tree properties for fields in CTRL0
Quoted 13 lines · Sean Anderson
Quoted 12 lines · Marek Vasut
Quoted 6 lines · Sean Anderson
Some devices have different layouts for the fields in CTRL0 (e.g. the Kendryte K210). Allow this layout to be configurable from the device tree. The documentation has been taken from Linux.
Signed-off-by Sean Anderson <[email protected]>Reviewed-by Simon Glass <[email protected]>Can't you just have different compatible string for each SoC and derive the various fields based on that compatible string, instead of describing all the register bitfields in DT ?
Quoted 5 lines
Quoted 2 lines
What does Linux do ?
Linux only supports socfpga boards. I don't know if there is any rhyme/reason to the shifting around of these fields.
Could be a different revision of the IP. This is usually handled by using SoC-specific compatible strings, see e.g. Linux Documentation/devicetree/bindings/usb/renesas,usb3-peri.yaml
You don't want to encode register layout in the DT.
Quoted 2 lines
It is possible to
add several compatible strings like "kendryte,k210-spi3".
Why ?
Quoted 6 lines
I chose this
method because the bitfields are different for spi0 and spi1, spi2, and spi3. If there are other incompatibilities discovered, then it may make more sense to use different strings. Another option could have been to use theDW_SPI_VERSIONfield to detect different controllers, but it is the same among all the controllers on the K210.
The controllers on the same SoC have different register layout ?
Signature · 2 lines
Best regards, Marek Vasut
PATCH 2/8 spi: dw: Add device tree properties for fields in CTRL0
Quoted 17 lines · Marek Vasut
Quoted 16 lines · Sean Anderson
Quoted 14 lines · Marek Vasut
Quoted 6 lines · Sean Anderson
Some devices have different layouts for the fields in CTRL0 (e.g. the Kendryte K210). Allow this layout to be configurable from the device tree. The documentation has been taken from Linux.
Signed-off-by Sean Anderson <[email protected]>Reviewed-by Simon Glass <[email protected]>Can't you just have different compatible string for each SoC and derive the various fields based on that compatible string, instead of describing all the register bitfields in DT ?
What does Linux do ?
Quoted 8 lines
Quoted 2 lines
Linux only supports socfpga boards. I don't know if there is any rhyme/reason to the shifting around of these fields.
Could be a different revision of the IP. This is usually handled by using SoC-specific compatible strings, see e.g. Linux
Documentation/devicetree/bindings/usb/renesas,usb3-peri.yamlYou don't want to encode register layout in the DT.
Ok, then I think adding compatible strings would be the cleanest.
Quoted 5 lines
Quoted 3 lines
It is possible to
add several compatible strings like "kendryte,k210-spi3".Why ?
See below.
Quoted 10 lines
Quoted 7 lines
I chose this
method because the bitfields are different for spi0 and spi1, spi2, and spi3. If there are other incompatibilities discovered, then it may make more sense to use different strings. Another option could have been to use theDW_SPI_VERSIONfield to detect different controllers, but it is the same among all the controllers on the K210.The controllers on the same SoC have different register layout ?
Yup!
Don't ask me why.
--Sean
PATCH 2/8 spi: dw: Add device tree properties for fields in CTRL0
Quoted 45 lines · Sean Anderson
Quoted 17 lines · Marek Vasut
Quoted 16 lines · Sean Anderson
Quoted 14 lines · Marek Vasut
Quoted 6 lines · Sean Anderson
Some devices have different layouts for the fields in CTRL0 (e.g. the Kendryte K210). Allow this layout to be configurable from the device tree. The documentation has been taken from Linux.
Signed-off-by Sean Anderson <[email protected]>Reviewed-by Simon Glass <[email protected]>Can't you just have different compatible string for each SoC and derive the various fields based on that compatible string, instead of describing all the register bitfields in DT ?
What does Linux do ?
Quoted 8 lines
Quoted 2 lines
Linux only supports socfpga boards. I don't know if there is any rhyme/reason to the shifting around of these fields.
Could be a different revision of the IP. This is usually handled by using SoC-specific compatible strings, see e.g. Linux
Documentation/devicetree/bindings/usb/renesas,usb3-peri.yamlYou don't want to encode register layout in the DT.
Ok, then I think adding compatible strings would be the cleanest.
Quoted 5 lines
Quoted 3 lines
It is possible to
add several compatible strings like "kendryte,k210-spi3".Why ?
See below.
Quoted 8 lines
Quoted 7 lines
I chose this
method because the bitfields are different for spi0 and spi1, spi2, and spi3. If there are other incompatibilities discovered, then it may make more sense to use different strings. Another option could have been to use theDW_SPI_VERSIONfield to detect different controllers, but it is the same among all the controllers on the K210.
Quoted 6 lines
Quoted 2 lines
The controllers on the same SoC have different register layout ?
Yup!
Don't ask me why.
Now that is truly an odd design. Is there a datasheet for this SoC ?
You might be able to somehow enumerate those controllers in DT and derive their layout from that enumeration or somesuch I think.
PATCH 2/8 spi: dw: Add device tree properties for fields in CTRL0
Quoted 26 lines · Marek Vasut
Quoted 25 lines · Sean Anderson
Quoted 5 lines · Marek Vasut
Could be a different revision of the IP. This is usually handled by using SoC-specific compatible strings, see e.g. Linux
Documentation/devicetree/bindings/usb/renesas,usb3-peri.yamlYou don't want to encode register layout in the DT.
Ok, then I think adding compatible strings would be the cleanest.
Quoted 5 lines
Quoted 3 lines
It is possible to
add several compatible strings like "kendryte,k210-spi3".Why ?
See below.
Quoted 8 lines
Quoted 7 lines
I chose this
method because the bitfields are different for spi0 and spi1, spi2, and spi3. If there are other incompatibilities discovered, then it may make more sense to use different strings. Another option could have been to use theDW_SPI_VERSIONfield to detect different controllers, but it is the same among all the controllers on the K210.
Quoted 8 lines
Quoted 6 lines
Quoted 2 lines
The controllers on the same SoC have different register layout ?
Yup!
Don't ask me why.
Now that is truly an odd design. Is there a datasheet for this SoC ?
Nope. Everything has been done referencing their sdk.
In hindsight, porting this board was a poor decision because of all the hoops I've had to jump through due to the absence of documentation. Unfortunately, it's probably the only budget risc-v board with S-mode until the end of the year or so.
Quoted 2 lines
You might be able to somehow enumerate those controllers in DT and derive their layout from that enumeration or somesuch I think.
So like derive it from the sequence number? I'd rather do this in a more standard way, if possible.
--Sean
PATCH 2/8 spi: dw: Add device tree properties for fields in CTRL0
Quoted 43 lines · Sean Anderson
Quoted 26 lines · Marek Vasut
Quoted 25 lines · Sean Anderson
Quoted 5 lines · Marek Vasut
Could be a different revision of the IP. This is usually handled by using SoC-specific compatible strings, see e.g. Linux
Documentation/devicetree/bindings/usb/renesas,usb3-peri.yamlYou don't want to encode register layout in the DT.
Ok, then I think adding compatible strings would be the cleanest.
Quoted 5 lines
Quoted 3 lines
It is possible to
add several compatible strings like "kendryte,k210-spi3".Why ?
See below.
Quoted 8 lines
Quoted 7 lines
I chose this
method because the bitfields are different for spi0 and spi1, spi2, and spi3. If there are other incompatibilities discovered, then it may make more sense to use different strings. Another option could have been to use theDW_SPI_VERSIONfield to detect different controllers, but it is the same among all the controllers on the K210.Quoted 8 lines
Quoted 6 lines
Quoted 2 lines
The controllers on the same SoC have different register layout ?
Yup!
Don't ask me why.
Now that is truly an odd design. Is there a datasheet for this SoC ?
Nope. Everything has been done referencing their sdk.
In hindsight, porting this board was a poor decision because of all the hoops I've had to jump through due to the absence of documentation. Unfortunately, it's probably the only budget risc-v board with S-mode until the end of the year or so.
Quoted 5 lines
Quoted 2 lines
You might be able to somehow enumerate those controllers in DT and derive their layout from that enumeration or somesuch I think.
So like derive it from the sequence number? I'd rather do this in a more standard way, if possible.
I would rather like to know why do the controllers have different register layout.
PATCH 3/8 spi: dw: Rename "cs-gpio" to "cs-gpios"
In reply to Sean AndersonThis property is named differently than other SPI drivers with the same property, as well as the property as used in Linux.
---
arch/arc/dts/axs10x_mb.dtsi | 3 ++- arch/arc/dts/hsdk.dts | 3 ++- drivers/spi/designware_spi.c | 10 +++------- 3 files changed, 7 insertions(+), 9 deletions(-)
arch/arc/dts/axs10x_mb.dtsi +2 -1
@@ -97,7 +97,8 @@ spi-max-frequency = <4000000>; clocks = <&apbclk>; clock-names = "spi_clk"; - cs-gpio = <&cs_gpio 0>; + num-cs = <1>; + cs-gpios = <&cs_gpio 0>; spi_flash at 0 { compatible = "jedec,spi-nor"; reg = <0>;
arch/arc/dts/hsdk.dts +2 -1
@@ -120,7 +120,8 @@ spi-max-frequency = <4000000>; clocks = <&cgu_clk CLK_SYS_SPI_REF>; clock-names = "spi_clk"; - cs-gpio = <&cs_gpio 0>; + num-cs = <1>; + cs-gpios = <&cs_gpio 0>; spi_flash at 0 { compatible = "jedec,spi-nor"; reg = <0>;
drivers/spi/designware_spi.c +3 -7
@@ -142,7 +142,8 @@ static int request_gpio_cs(struct udevice *bus)int ret;/* External chip select gpio line is optional */ - ret =gpio_request_by_name (bus,"cs-gpio" ,0 , &priv->cs_gpio,0 ); + ret =gpio_request_by_name (bus,"cs-gpios" ,0 , &priv->cs_gpio, +GPIOD_IS_OUT |GPIOD_IS_OUT_ACTIVE );if (ret == -ENOENT )return 0 ;
@@ -151,12 +152,7 @@ static int request_gpio_cs(struct udevice *bus) return ret; } -if (dm_gpio_is_valid (&priv->cs_gpio)) { -dm_gpio_set_dir_flags (&priv->cs_gpio, -GPIOD_IS_OUT |GPIOD_IS_OUT_ACTIVE ); - } - -debug ("%s: used external gpio for CS management\n" , __func__); +debug ("%s: using external gpio for CS management\n" , __func__);#endif return 0 ; }
Signature · 1 line
2.25.0
PATCH 3/8 spi: dw: Rename "cs-gpio" to "cs-gpios"
Quoted 10 lines · Sean Anderson
This property is named differently than other SPI drivers with the same property, as well as the property as used in Linux.
Signed-off-by Sean Anderson <[email protected]>---
arch/arc/dts/axs10x_mb.dtsi | 3 ++- arch/arc/dts/hsdk.dts | 3 ++- drivers/spi/designware_spi.c | 10 +++-------
Better separate the dts changes and add sha1 from Linux if it synced.
PATCH 3/8 spi: dw: Rename "cs-gpio" to "cs-gpios"
Quoted 5 lines · Jagan Teki
Quoted 4 lines · Sean Anderson
This property is named differently than other SPI drivers with the same property, as well as the property as used in Linux.
Quoted 9 lines
Quoted 6 lines
Signed-off-by Sean Anderson <[email protected]>---
arch/arc/dts/axs10x_mb.dtsi | 3 ++- arch/arc/dts/hsdk.dts | 3 ++- drivers/spi/designware_spi.c | 10 +++-------Better separate the dts changes and add sha1 from Linux if it synced.
This is not from a specific patch; I just noticed that it was different and changed it. I think it is clearer to include dts changes with the code change. That way if someone is reviewing the device tree, it is obvious why the change was made. Splitting the changes would also make the code not run properly for the intermediate commit. This can be annoying when bisecting. However, if you would still like it split, I can do that.
--Sean
PATCH 4/8 spi: dw: Use generic function to read reg address
In reply to Sean AndersonUsing an fdt-specific function causes problems when compiled with a live tree.
---
drivers/spi/designware_spi.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/spi/designware_spi.c +3 -1
@@ -161,7 +161,9 @@ static int dw_spi_ofdata_to_platdata(struct udevice *bus) {struct dw_spi_platdata *plat = bus->platdata; - plat->regs = (struct dw_spi *)devfdt_get_addr (bus); + plat->regs =dev_read_addr_ptr (bus); +if (!plat->regs) +return -EINVAL ;/* Use 500KHz as a suitable default */ plat->frequency = dev_read_u32_default(bus, "spi-max-frequency",
Signature · 1 line
2.25.0
PATCH 4/8 spi: dw: Use generic function to read reg address
Quoted 15 lines · Sean Anderson
Using an fdt-specific function causes problems when compiled with a live tree.
Signed-off-by Sean Anderson <[email protected]>---
drivers/spi/designware_spi.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)drivers/spi/designware_spi.c +0
-0
drivers/spi/designware_spi.c static int dw_spi_ofdata_to_platdata(struct udevice *bus) · line 166
Quoted 7 lines
drivers/spi/designware_spi.c +3
-1@@ -161,7 +161,9 @@ static int dw_spi_ofdata_to_platdata(struct udevice *bus) {struct dw_spi_platdata *plat = bus->platdata; - plat->regs = (struct dw_spi *)devfdt_get_addr (bus); + plat->regs =dev_read_addr_ptr (bus); +if (!plat->regs) +return -EINVAL ;
Better check the returned regs with FDT_ADDR_T_NONE
PATCH 4/8 spi: dw: Use generic function to read reg address
Quoted 19 lines · Jagan Teki
Quoted 18 lines · Sean Anderson
Using an fdt-specific function causes problems when compiled with a live tree.
Signed-off-by Sean Anderson <[email protected]>---
drivers/spi/designware_spi.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)drivers/spi/designware_spi.c +0
-0@@ -161,7 +161,9 @@ static int dw_spi_ofdata_to_platdata(struct udevice *bus) {struct dw_spi_platdata *plat = bus->platdata;
Quoted 7 lines
drivers/spi/designware_spi.c static int dw_spi_ofdata_to_platdata(struct udevice *bus) · line 166
Quoted 4 lines
drivers/spi/designware_spi.c +3
-1- plat->regs = (struct dw_spi *)devfdt_get_addr (bus); + plat->regs =dev_read_addr_ptr (bus); +if (!plat->regs) +return -EINVAL ;Better check the returned regs with
FDT_ADDR_T_NONE
This series depends on the series for k210 support which includes the patch "dm: Fix error handling for dev_read_addr_ptr" [1]. This patch changes the semantics for that function to be consistent regardless of whether a live device tree is in use.
[1] https://patchwork.ozlabs.org/patch/1258450/
--Sean
PATCH 5/8 spi: dw: Speed up transfer loops
In reply to Sean AndersonThe transfer loops are very tight on some platforms (especially on higher speeds). If we don't read/write fast enough we can run into over-/under- flow problems. This patch removes several divisions and log statements, and simplifies the read logic.
---
drivers/spi/designware_spi.c | 29 +++++++++-------------------- 1 file changed, 9 insertions(+), 20 deletions(-)
drivers/spi/designware_spi.c +9 -20
@@ -304,7 +304,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv) {u32 tx_left, tx_room, rxtx_gap; - tx_left = (priv->tx_end - priv->tx) / (priv->bits_per_word >>3 ); + tx_left = priv->tx_end - priv->tx; tx_room = priv->fifo_len -dw_read (priv,DW_SPI_TXFLR );/*
@@ -315,8 +315,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv)* shift registers. So a control from sw point of * view is taken. */ - rxtx_gap = ((priv->rx_end - priv->rx) - (priv->tx_end - priv->tx)) / - (priv->bits_per_word >>3 ); + rxtx_gap = ((priv->rx_end - priv->rx) - (priv->tx_end - priv->tx));return min3 (tx_left, tx_room, (u32)(priv->fifo_len - rxtx_gap)); }
@@ -324,7 +323,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv)/* Return the max entries we should read out of rx fifo */ static inline u32 rx_max (struct dw_spi_priv *priv) { -u32 rx_left = (priv->rx_end - priv->rx) / (priv->bits_per_word >>3 ); +u32 rx_left = priv->rx_end - priv->rx;return min_t (u32, rx_left,dw_read (priv,DW_SPI_RXFLR )); }
@@ -336,15 +335,10 @@ static void dw_writer(struct dw_spi_priv *priv)while (max--) {/* Set the tx word if the transfer's original "tx" is not null */ -if (priv->tx_end - priv->len) { -if (priv->bits_per_word ==8 ) - txw = *(u8 *)(priv->tx); -else - txw = *(u16 *)(priv->tx); - } +if (priv->tx_end - priv->len) + txw = *(u8 *)(priv->tx);dw_write (priv,DW_SPI_DR , txw); -debug ("%s: tx=0x%02x\n" , __func__, txw); - priv->tx += priv->bits_per_word >>3 ; + priv->tx++; } }
@@ -355,16 +349,11 @@ static void dw_reader(struct dw_spi_priv *priv)while (max--) { rxw =dw_read (priv,DW_SPI_DR ); -debug ("%s: rx=0x%02x\n" , __func__, rxw);/* Care about rx if the transfer's original "rx" is not null */ -if (priv->rx_end - priv->len) { -if (priv->bits_per_word ==8 ) - *(u8 *)(priv->rx) = rxw; -else - *(u16 *)(priv->rx) = rxw; - } - priv->rx += priv->bits_per_word >>3 ; +if (priv->rx_end - priv->len) + *(u8 *)(priv->rx) = rxw; + priv->rx++; } }
Signature · 1 line
2.25.0
PATCH 5/8 spi: dw: Speed up transfer loops
Quoted 49 lines · Sean Anderson
The transfer loops are very tight on some platforms (especially on higher speeds). If we don't read/write fast enough we can run into over-/under- flow problems. This patch removes several divisions and log statements, and simplifies the read logic.
Signed-off-by Sean Anderson <[email protected]>---
drivers/spi/designware_spi.c | 29 +++++++++-------------------- 1 file changed, 9 insertions(+), 20 deletions(-)drivers/spi/designware_spi.c +3
-6@@ -304,7 +304,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv) {u32 tx_left, tx_room, rxtx_gap; - tx_left = (priv->tx_end - priv->tx) / (priv->bits_per_word >>3 ); + tx_left = priv->tx_end - priv->tx; tx_room = priv->fifo_len -dw_read (priv,DW_SPI_TXFLR );/* @@ -315,8 +315,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv)* shift registers. So a control from sw point of * view is taken. */ - rxtx_gap = ((priv->rx_end - priv->rx) - (priv->tx_end - priv->tx)) / - (priv->bits_per_word >>3 ); + rxtx_gap = ((priv->rx_end - priv->rx) - (priv->tx_end - priv->tx));return min3 (tx_left, tx_room, (u32)(priv->fifo_len - rxtx_gap)); }@@ -324,7 +323,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv)/* Return the max entries we should read out of rx fifo */ static inline u32 rx_max (struct dw_spi_priv *priv) { -u32 rx_left = (priv->rx_end - priv->rx) / (priv->bits_per_word >>3 ); +u32 rx_left = priv->rx_end - priv->rx;return min_t (u32, rx_left,dw_read (priv,DW_SPI_RXFLR )); }@@ -336,15 +335,10 @@ static void dw_writer(struct dw_spi_priv *priv)while (max--) {/* Set the tx word if the transfer's original "tx" is not null */ -if (priv->tx_end - priv->len) { -if (priv->bits_per_word ==8 )
drivers/spi/designware_spi.c static void dw_writer(struct dw_spi_priv *priv) · line 341
Quoted 10 lines
drivers/spi/designware_spi.c +3
-6- txw = *(u8 *)(priv->tx); - else - txw = *(u16 *)(priv->tx); - } +if (priv->tx_end - priv->len) + txw = *(u8 *)(priv->tx);dw_write (priv,DW_SPI_DR , txw); -debug ("%s: tx=0x%02x\n" , __func__, txw); - priv->tx += priv->bits_per_word >>3 ; + priv->tx++;
This breaks 16 bits per word transfers, NAK.
The compiler should be able to figure out the rest of the optimizations in this patch.
PATCH 5/8 spi: dw: Speed up transfer loops
Quoted 63 lines · Marek Vasut
Quoted 49 lines · Sean Anderson
The transfer loops are very tight on some platforms (especially on higher speeds). If we don't read/write fast enough we can run into over-/under- flow problems. This patch removes several divisions and log statements, and simplifies the read logic.
Signed-off-by Sean Anderson <[email protected]>---
drivers/spi/designware_spi.c | 29 +++++++++-------------------- 1 file changed, 9 insertions(+), 20 deletions(-)drivers/spi/designware_spi.c +3
-6@@ -304,7 +304,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv) {u32 tx_left, tx_room, rxtx_gap; - tx_left = (priv->tx_end - priv->tx) / (priv->bits_per_word >>3 ); + tx_left = priv->tx_end - priv->tx; tx_room = priv->fifo_len -dw_read (priv,DW_SPI_TXFLR );/* @@ -315,8 +315,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv)* shift registers. So a control from sw point of * view is taken. */ - rxtx_gap = ((priv->rx_end - priv->rx) - (priv->tx_end - priv->tx)) / - (priv->bits_per_word >>3 ); + rxtx_gap = ((priv->rx_end - priv->rx) - (priv->tx_end - priv->tx));return min3 (tx_left, tx_room, (u32)(priv->fifo_len - rxtx_gap)); }@@ -324,7 +323,7 @@ static inline u32 tx_max(struct dw_spi_priv *priv)/* Return the max entries we should read out of rx fifo */ static inline u32 rx_max (struct dw_spi_priv *priv) { -u32 rx_left = (priv->rx_end - priv->rx) / (priv->bits_per_word >>3 ); +u32 rx_left = priv->rx_end - priv->rx;return min_t (u32, rx_left,dw_read (priv,DW_SPI_RXFLR )); }@@ -336,15 +335,10 @@ static void dw_writer(struct dw_spi_priv *priv)while (max--) {/* Set the tx word if the transfer's original "tx" is not null */ -if (priv->tx_end - priv->len) { -if (priv->bits_per_word ==8 )drivers/spi/designware_spi.c static void dw_writer(struct dw_spi_priv *priv) · line 341
Quoted 10 lines
drivers/spi/designware_spi.c +3
-6- txw = *(u8 *)(priv->tx); - else - txw = *(u16 *)(priv->tx); - } +if (priv->tx_end - priv->len) + txw = *(u8 *)(priv->tx);dw_write (priv,DW_SPI_DR , txw); -debug ("%s: tx=0x%02x\n" , __func__, txw); - priv->tx += priv->bits_per_word >>3 ; + priv->tx++;This breaks 16 bits per word transfers, NAK.
Quoted 3 lines
The compiler should be able to figure out the rest of the optimizations in this patch.
Hm, I will try with just the debug symbols removed.
--Sean
PATCH 6/8 spi: dw: Add mem_ops
In reply to Sean AndersonThe designware ssi device has "broken" chip select behaviour [1], and needs specific manipulation to use the built-in chip select. The existing fix is to use an external GPIO for chip select, but typically the K210 has SPI3 directly connected to a flash chip with dedicated pins. This makes it impossible to use the spi_xfer function to use spi, since the CS is de-asserted in between calls. This patch adds an implementation of exec_op, which gives correct behaviour when reading/writing spi flash.
Work on this device has been difficult because the only example code I have to work off is Kendryte's sdk, and I do not have access to the datasheet (if anyone does, I would love to have a look!). The MMC device is still not working, but I have been making progress.
[1] https://lkml.org/lkml/2015/12/23/132
---
drivers/spi/designware_spi.c | 128 ++++++++++++++++++++++++++++++++++- 1 file changed, 126 insertions(+), 2 deletions(-)
drivers/spi/designware_spi.c +126 -2
@@ -17,6 +17,7 @@#include <errno.h> #include <malloc.h> #include <spi.h> +#include <spi-mem.h> #include <fdtdec.h> #include <reset.h> #include <dm/device_compat.h>
@@ -108,8 +109,8 @@ struct dw_spi_priv {int len;u32 fifo_len;/* depth of the FIFO buffer */ -void *tx; -void *tx_end; +const void *tx; +const void *tx_end;void *rx;void *rx_end;
@@ -471,6 +472,124 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen,return ret; } +/* +* This function is necessary for reading SPI flash with the native CS +* c.f. https://lkml.org/lkml/2015/12/23/132 +*/ +static int dw_spi_exec_op (struct spi_slave *slave,const struct spi_mem_op *op) +{ +bool read = op->data.dir ==SPI_MEM_DATA_IN ; +int pos, i, ret =0 ; +struct udevice *bus = slave->dev->parent; +struct dw_spi_platdata *plat =dev_get_platdata (bus); +struct dw_spi_priv *priv =dev_get_priv (bus); +u8 op_len =sizeof (op->cmd.opcode) + op->addr.nbytes + op->dummy.nbytes; +u8 op_buf[op_len]; +u32 cr0; + +if (read) + priv->tmode =SPI_TMOD_EPROMREAD ; +else + priv->tmode =SPI_TMOD_TO ; + +debug ("%s: buf=%p len=%u [bytes]\n" , + __func__, op->data.buf.in, op->data.nbytes); + + cr0 =GEN_CTRL0 (priv, plat); +debug ("%s: cr0=%08x\n" , __func__, cr0); + +spi_enable_chip (priv,0 ); +dw_write (priv,DW_SPI_CTRL0 , cr0); +if (read) +dw_write (priv,DW_SPI_CTRL1 , op->data.nbytes -1 ); +spi_enable_chip (priv,1 ); + +/* From spi_mem_exec_op */ + pos =0 ; + op_buf[pos++] = op->cmd.opcode; +if (op->addr.nbytes) { +for (i =0 ; i < op->addr.nbytes; i++) + op_buf[pos + i] = op->addr.val >> + (8 * (op->addr.nbytes - i -1 )); + + pos += op->addr.nbytes; + } +if (op->dummy.nbytes) +memset (op_buf + pos,0xff , op->dummy.nbytes); + + priv->tx = &op_buf; + priv->tx_end = priv->tx + op_len; + priv->rx =NULL ; + priv->rx_end =NULL ; +while (priv->tx != priv->tx_end) { +dw_writer (priv); +/* This loop needs a delay otherwise we can hang */ +udelay (1 ); + } + +/* +* XXX: The following are tight loops! Enabling debug messages may cause +* them to fail because we are not reading/writing the fifo fast enough. +* +* We heuristically break out of the loop when we stop getting data. +* This is to stop us from hanging if the device doesn't send any data +* (either at all, or after sending a response). For example, one flash +* chip I tested did not send anything back after the first 64K of data. +*/ +if (read) { +/* If we have gotten any data back yet */ +bool got_data = false; +/* How many times we have looped without reading anything */ +int loops_since_read =0 ; +struct spi_mem_op *mut_op = (struct spi_mem_op *)op; + + priv->rx = op->data.buf.in; + priv->rx_end = priv->rx + op->data.nbytes; + +dw_write (priv,DW_SPI_SER ,1 <<spi_chip_select (slave->dev)); +while (priv->rx != priv->rx_end) { +void *last_rx = priv->rx; + +dw_reader (priv); +if (priv->rx == last_rx) { + loops_since_read++; +/* Thresholds are arbitrary */ +if (loops_since_read >256 ) +break ; +else if (got_data && loops_since_read >32 ) +break ; + }else { + got_data = true; + loops_since_read =0 ; + } + } + +/* Update with the actual amount of data read */ + mut_op->data.nbytes -= priv->rx_end - priv->rx; + }else { +u32 val; + + priv->tx = op->data.buf.out; + priv->tx_end = priv->tx + op->data.nbytes; + +/* Fill up the write fifo before starting the transfer */ +dw_writer (priv); +dw_write (priv,DW_SPI_SER ,1 <<spi_chip_select (slave->dev)); +while (priv->tx != priv->tx_end) +dw_writer (priv); + +if (readl_poll_timeout (priv->regs +DW_SPI_SR , val, + (val &SR_TF_EMPT ) && !(val &SR_BUSY ), +RX_TIMEOUT *1000 )) { + ret = -ETIMEDOUT ; + } + } + +dw_write (priv,DW_SPI_SER ,0 ); +debug ("%s: %u bytes xfered\n" , __func__, op->data.nbytes); +return ret; +} +static int dw_spi_set_speed (struct udevice *bus,uint speed) {struct dw_spi_platdata *plat =dev_get_platdata (bus);
@@ -534,8 +653,13 @@ static int dw_spi_remove(struct udevice *bus)return 0 ; } +static const struct spi_controller_mem_ops dw_spi_mem_ops = { + .exec_op = dw_spi_exec_op, +}; +static const struct dm_spi_ops dw_spi_ops = { .xfer = dw_spi_xfer, + .mem_ops = &dw_spi_mem_ops, .set_speed = dw_spi_set_speed, .set_mode = dw_spi_set_mode,/*
Signature · 1 line
2.25.0
PATCH 6/8 spi: dw: Add mem_ops
Hi Sean,
do you have branch with this code (all dw spi changes) in some public repo? I would like to test it with our board (which have DW SPI).
---
Eugeniy Paltsev
________________________________________
From: Sean Anderson <[email protected]>
Sent: Thursday, March 5, 2020 22:19
To: u-boot at lists.denx.de
Cc: Simon Glass; Jagan Teki; Sean Anderson; Eugeniy Paltsev
Subject: [PATCH v1 6/8] spi: dw: Add mem_ops
The designware ssi device has "broken" chip select behaviour [1], and needs specific manipulation to use the built-in chip select. The existing fix is to use an external GPIO for chip select, but typically the K210 has SPI3 directly connected to a flash chip with dedicated pins. This makes it impossible to use the spi_xfer function to use spi, since the CS is de-asserted in between calls. This patch adds an implementation of exec_op, which gives correct behaviour when reading/writing spi flash.
Work on this device has been difficult because the only example code I have to work off is Kendryte's sdk, and I do not have access to the datasheet (if anyone does, I would love to have a look!). The MMC device is still not working, but I have been making progress.
---
drivers/spi/designware_spi.c | 128 ++++++++++++++++++++++++++++++++++- 1 file changed, 126 insertions(+), 2 deletions(-)
drivers/spi/designware_spi.c +126 -2
@@ -17,6 +17,7 @@#include <errno.h> #include <malloc.h> #include <spi.h> +#include <spi-mem.h> #include <fdtdec.h> #include <reset.h> #include <dm/device_compat.h>
@@ -108,8 +109,8 @@ struct dw_spi_priv {int len;u32 fifo_len;/* depth of the FIFO buffer */ -void *tx; -void *tx_end; +const void *tx; +const void *tx_end;void *rx;void *rx_end;
@@ -471,6 +472,124 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen,return ret; } +/* +* This function is necessary for reading SPI flash with the native CS +* c.f. https://urldefense.proofpoint.com/v2/url?u=https-3A__lkml.org_lkml_2015_12_23_132&d=DwIDAg&c=DPL6_X_6JkXFx7AXWqB0tg&r=ZlJN1MriPUTkBKCrPSx67GmaplEUGcAEk9yPtCLdUXI&m=WVwKMzBXasdUvVoschXNTC5C7t39Ta0E7Ly3uEPRT_0&s=7dEhNfWpefL5yAqFi1Ztrve9SBPM_n3OoIJoH40hgpQ&e= +*/ +static int dw_spi_exec_op (struct spi_slave *slave,const struct spi_mem_op *op) +{ +bool read = op->data.dir ==SPI_MEM_DATA_IN ; +int pos, i, ret =0 ; +struct udevice *bus = slave->dev->parent; +struct dw_spi_platdata *plat =dev_get_platdata (bus); +struct dw_spi_priv *priv =dev_get_priv (bus); +u8 op_len =sizeof (op->cmd.opcode) + op->addr.nbytes + op->dummy.nbytes; +u8 op_buf[op_len]; +u32 cr0; + +if (read) + priv->tmode =SPI_TMOD_EPROMREAD ; +else + priv->tmode =SPI_TMOD_TO ; + +debug ("%s: buf=%p len=%u [bytes]\n" , + __func__, op->data.buf.in, op->data.nbytes); + + cr0 =GEN_CTRL0 (priv, plat); +debug ("%s: cr0=%08x\n" , __func__, cr0); + +spi_enable_chip (priv,0 ); +dw_write (priv,DW_SPI_CTRL0 , cr0); +if (read) +dw_write (priv,DW_SPI_CTRL1 , op->data.nbytes -1 ); +spi_enable_chip (priv,1 ); + +/* From spi_mem_exec_op */ + pos =0 ; + op_buf[pos++] = op->cmd.opcode; +if (op->addr.nbytes) { +for (i =0 ; i < op->addr.nbytes; i++) + op_buf[pos + i] = op->addr.val >> + (8 * (op->addr.nbytes - i -1 )); + + pos += op->addr.nbytes; + } +if (op->dummy.nbytes) +memset (op_buf + pos,0xff , op->dummy.nbytes); + + priv->tx = &op_buf; + priv->tx_end = priv->tx + op_len; + priv->rx =NULL ; + priv->rx_end =NULL ; +while (priv->tx != priv->tx_end) { +dw_writer (priv); +/* This loop needs a delay otherwise we can hang */ +udelay (1 ); + } + +/* +* XXX: The following are tight loops! Enabling debug messages may cause +* them to fail because we are not reading/writing the fifo fast enough. +* +* We heuristically break out of the loop when we stop getting data. +* This is to stop us from hanging if the device doesn't send any data +* (either at all, or after sending a response). For example, one flash +* chip I tested did not send anything back after the first 64K of data. +*/ +if (read) { +/* If we have gotten any data back yet */ +bool got_data = false; +/* How many times we have looped without reading anything */ +int loops_since_read =0 ; +struct spi_mem_op *mut_op = (struct spi_mem_op *)op; + + priv->rx = op->data.buf.in; + priv->rx_end = priv->rx + op->data.nbytes; + +dw_write (priv,DW_SPI_SER ,1 <<spi_chip_select (slave->dev)); +while (priv->rx != priv->rx_end) { +void *last_rx = priv->rx; + +dw_reader (priv); +if (priv->rx == last_rx) { + loops_since_read++; +/* Thresholds are arbitrary */ +if (loops_since_read >256 ) +break ; +else if (got_data && loops_since_read >32 ) +break ; + }else { + got_data = true; + loops_since_read =0 ; + } + } + +/* Update with the actual amount of data read */ + mut_op->data.nbytes -= priv->rx_end - priv->rx; + }else { +u32 val; + + priv->tx = op->data.buf.out; + priv->tx_end = priv->tx + op->data.nbytes; + +/* Fill up the write fifo before starting the transfer */ +dw_writer (priv); +dw_write (priv,DW_SPI_SER ,1 <<spi_chip_select (slave->dev)); +while (priv->tx != priv->tx_end) +dw_writer (priv); + +if (readl_poll_timeout (priv->regs +DW_SPI_SR , val, + (val &SR_TF_EMPT ) && !(val &SR_BUSY ), +RX_TIMEOUT *1000 )) { + ret = -ETIMEDOUT ; + } + } + +dw_write (priv,DW_SPI_SER ,0 ); +debug ("%s: %u bytes xfered\n" , __func__, op->data.nbytes); +return ret; +} +static int dw_spi_set_speed (struct udevice *bus,uint speed) {struct dw_spi_platdata *plat =dev_get_platdata (bus);
@@ -534,8 +653,13 @@ static int dw_spi_remove(struct udevice *bus)return 0 ; } +static const struct spi_controller_mem_ops dw_spi_mem_ops = { + .exec_op = dw_spi_exec_op, +}; +static const struct dm_spi_ops dw_spi_ops = { .xfer = dw_spi_xfer, + .mem_ops = &dw_spi_mem_ops, .set_speed = dw_spi_set_speed, .set_mode = dw_spi_set_mode,/*
--
2.25.0
PATCH 6/8 spi: dw: Add mem_ops
Quoted 7 lines · Eugeniy Paltsev
Hi Sean,
do you have branch with this code (all dw spi changes) in some public repo? I would like to test it with our board (which have DW SPI).
---
Eugeniy Paltsev
A full tree is available at
https://github.com/Forty-Bot/u-boot/tree/maix_spi
--Sean
PATCH 6/8 spi: dw: Add mem_ops
Hi Sean,
I've tested the SPI (with SPI flash) on HSDK board (which have DW SPI) with your changes. It completely break SPI on HSDK:
--------------------->8--------------------------
# sf probe unrecognized JEDEC id bytes: ff, ff, ff Failed to initialize SPI flash at 0:0 (error -2) --------------------->8--------------------------
Tested from maix_spi HEAD (e338571bf528f58b3ced7fbd0c1f5d923caa1cfd)
---
Eugeniy Paltsev
________________________________________
From: Sean Anderson <[email protected]>
Sent: Friday, March 6, 2020 03:48
To: Eugeniy Paltsev; u-boot at lists.denx.de
Cc: Simon Glass; Jagan Teki; Alexey Brodkin
Subject: Re: [PATCH v1 6/8] spi: dw: Add mem_ops
Quoted 7 lines · Eugeniy Paltsev
Hi Sean,
do you have branch with this code (all dw spi changes) in some public repo? I would like to test it with our board (which have DW SPI).
---
Eugeniy Paltsev
--Sean
PATCH 6/8 spi: dw: Add mem_ops
Quoted 11 lines · Eugeniy Paltsev
Hi Sean,
I've tested the SPI (with SPI flash) on HSDK board (which have DW SPI) with your changes. It completely break SPI on HSDK:
--------------------->8--------------------------
# sf probe unrecognized JEDEC id bytes: ff, ff, ff Failed to initialize SPI flash at 0:0 (error -2) --------------------->8--------------------------
Quoted 4 lines
Tested from
maix_spiHEAD (e338571bf528f58b3ced7fbd0c1f5d923caa1cfd)---
Eugeniy Paltsev
Can you try testing without this patch, but with all the other patches in the series? Alternatively, can you try testing with this patch, but withpout the previous one ([PATCH v1 5/8] spi: dw: Speed up transfer loops), and with logging/debug statements enabled?
--Sean
PATCH 6/8 spi: dw: Add mem_ops
In reply to Eugeniy PaltsevQuoted 11 lines · Eugeniy Paltsev
Hi Sean,
I've tested the SPI (with SPI flash) on HSDK board (which have DW SPI) with your changes. It completely break SPI on HSDK:
--------------------->8--------------------------
# sf probe unrecognized JEDEC id bytes: ff, ff, ff Failed to initialize SPI flash at 0:0 (error -2) --------------------->8--------------------------
Quoted 4 lines
Tested from
maix_spiHEAD (e338571bf528f58b3ced7fbd0c1f5d923caa1cfd)---
Eugeniy Paltsev
Actually, it just occured to me that I did not add support for a gpio cs to the xfer function, so it's likely that the chip is not enabling the cs. Can you try testing with the following patch
--- drivers/spi/designware_spi.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/spi/designware_spi.c +4 -0
@@ -517,6 +517,8 @@ static int dw_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)if (op->dummy.nbytes)memset (op_buf + pos,0xff , op->dummy.nbytes); +external_cs_manage (dev, false); + priv->tx = &op_buf; priv->tx_end = priv->tx + op_len; priv->rx =NULL ;
@@ -586,6 +588,8 @@ static int dw_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op) }dw_write (priv,DW_SPI_SER ,0 ); +external_cs_manage (dev, true); +debug ("%s: %u bytes xfered\n" , __func__, op->data.nbytes);return ret; }
Signature · 1 line
2.25.0
PATCH 6/8 spi: dw: Add mem_ops
Hi Sean,
even after fixing build errors with this patch I still have issues with communications to flash IC.
Now it is detected correctly (JEDEC id is valid) but I have issues with read or write. I need to look to that more intently.
---
Eugeniy Paltsev
________________________________________
From: Sean Anderson <[email protected]>
Sent: Saturday, March 7, 2020 00:20
To: Eugeniy Paltsev; u-boot at lists.denx.de
Cc: Simon Glass; Jagan Teki; Alexey Brodkin
Subject: Re: [PATCH v1 6/8] spi: dw: Add mem_ops
Quoted 11 lines · Eugeniy Paltsev
Hi Sean,
I've tested the SPI (with SPI flash) on HSDK board (which have DW SPI) with your changes. It completely break SPI on HSDK:
--------------------->8--------------------------
# sf probe unrecognized JEDEC id bytes: ff, ff, ff Failed to initialize SPI flash at 0:0 (error -2) --------------------->8--------------------------
Quoted 4 lines
Tested from
maix_spiHEAD (e338571bf528f58b3ced7fbd0c1f5d923caa1cfd)---
Eugeniy Paltsev
Actually, it just occured to me that I did not add support for a gpio cs to the xfer function, so it's likely that the chip is not enabling the cs. Can you try testing with the following patch
--- drivers/spi/designware_spi.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/spi/designware_spi.c +4 -0
@@ -517,6 +517,8 @@ static int dw_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)if (op->dummy.nbytes)memset (op_buf + pos,0xff , op->dummy.nbytes); +external_cs_manage (dev, false); + priv->tx = &op_buf; priv->tx_end = priv->tx + op_len; priv->rx =NULL ;
@@ -586,6 +588,8 @@ static int dw_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op) }dw_write (priv,DW_SPI_SER ,0 ); +external_cs_manage (dev, true); +debug ("%s: %u bytes xfered\n" , __func__, op->data.nbytes);return ret; }
--
2.25.0
PATCH 7/8 riscv: Add device tree bindings for SPI
In reply to Sean AndersonThis patch adds bindings for the MMC slot and SPI flash on the Sipeed Maix Bit.
---
arch/riscv/dts/k210-maix-bit.dts | 90 ++++++++++++++++++++++++++++++++ arch/riscv/dts/k210.dtsi | 12 +++++ 2 files changed, 102 insertions(+)
arch/riscv/dts/k210-maix-bit.dts +90 -0
@@ -235,9 +235,99 @@ pins = "IO_47"; }; }; + + fpioa_spi0: spi0 { + cs0 { + function = "GPIOHS28"; + pins = "IO_36"; + }; + rst { + function = "GPIOHS29"; + pins = "IO_37"; + }; + dc { + function = "GPIOHS30"; + pins = "IO_38"; + }; + wr { + function = "SPI0_SCK"; + pins = "IO_39"; + }; + }; + + fpioa_spi1: spi1 { + miso { + function = "SPI1_D1"; + pins = "IO_26"; + }; + clk { + function = "SPI1_SCLK"; + pins = "IO_27"; + }; + mosi { + function = "SPI1_D0"; + pins = "IO_28"; + }; + cs0 { + function = "GPIOHS31"; + pins = "IO_29"; + }; + }; +}; + +&wdt0 { + status = "okay"; }; &dvp0 { pinctrl-0 = <&fpioa_dvp>; pinctrl-names = "default"; }; + +&spi0 { + pinctrl-0 = <&fpioa_spi0>; + pinctrl-names = "default"; + num-cs = <1>; + cs-gpios = <&gpio0 28 0>; + + panel at 0 { + compatible = "sitronix,st8898v"; + reg = <0>; + reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + spi-max-frequency = <15000000>; + status = "disabled"; + }; +}; + +&spi1 { + pinctrl-0 = <&fpioa_spi1>; + pinctrl-names = "default"; + num-cs = <1>; + cs-gpios = <&gpio0 31 0>; + status = "okay"; + + slot at 0 { + compatible = "mmc-spi-slot"; + reg = <0>; + spi-max-frequency = <25000000>; + voltage-ranges = <3300 3300>; + broken-cd; + disable-wp; + }; +}; + +&spi3 { + status = "okay"; + + spi-flash at 0 { + compatible = "winbond,w25q128fw", "jedec,spi-nor"; + reg = <0>; + /* + * Datasheet says it should work at 100 MHz with fast read, but + * after testing it doesn't probe at that frequency + */ + spi-max-frequency = <50000000>; + m25p,fast-read; + broken-flash-reset; + }; +};
arch/riscv/dts/k210.dtsi +12 -0
@@ -592,6 +592,10 @@ spi-max-frequency = <25000000>; num-cs = <4>; reg-io-width = <4>; + snps,dfs-offset = <16>; + snps,frf-offset = <21>; + snps,tmod-offset = <8>; + snps,mode-offset = <6>; status = "disabled"; };
@@ -608,6 +612,10 @@ spi-max-frequency = <25000000>; num-cs = <4>; reg-io-width = <4>; + snps,dfs-offset = <16>; + snps,frf-offset = <21>; + snps,tmod-offset = <8>; + snps,mode-offset = <6>; status = "disabled"; };
@@ -625,6 +633,10 @@ spi-max-frequency = <100000000>; num-cs = <4>; reg-io-width = <4>; + snps,dfs-offset = <0>; + snps,frf-offset = <22>; + snps,tmod-offset = <10>; + snps,mode-offset = <8>; status = "disabled"; }; };
Signature · 1 line
2.25.0
PATCH 7/8 riscv: Add device tree bindings for SPI
Quoted 2 lines · Sean Anderson
This patch adds bindings for the MMC slot and SPI flash on the Sipeed Maix Bit.
The mail subject should say this is for specific SoC. [...]
arch/riscv/dts/k210-maix-bit.dts line 280
Quoted 3 lines
+&wdt0 {
arch/riscv/dts/k210-maix-bit.dts +1
-0+ status = "okay"; };
This shouldn't be here I guess ?
You should split this into the .dtsi addition for SoC and board specific patch.
PATCH 7/8 riscv: Add device tree bindings for SPI
Quoted 5 lines · Marek Vasut
Quoted 2 lines · Sean Anderson
This patch adds bindings for the MMC slot and SPI flash on the Sipeed Maix Bit.
The mail subject should say this is for specific SoC
Oh, whoops. This will be fixed in the next revision.
Quoted 7 lines
[...]
arch/riscv/dts/k210-maix-bit.dts line 280
Quoted 3 lines
+&wdt0 {
arch/riscv/dts/k210-maix-bit.dts +1
-0+ status = "okay"; };This shouldn't be here I guess ?
Yeah, this was meant to be added in a separate series for the wdt.
Quoted 3 lines
You should split this into the .dtsi addition for SoC and board specific patch.
Ok.
--Sean
PATCH 8/8 riscv: Add support for SPI on Kendryte K210
In reply to Sean AndersonThis patch enables configs necessary for usign SPI. It also adds some documentation.
---
board/sipeed/maix/Kconfig | 10 ++++ configs/sipeed_maix_bitm_defconfig | 8 +++ doc/board/sipeed/maix.rst | 94 +++++++++++++++++++----------- 3 files changed, 79 insertions(+), 33 deletions(-)
board/sipeed/maix/Kconfig +10 -0
@@ -57,4 +57,14 @@ config BOARD_SPECIFIC_OPTIONS imply CMD_GPIO imply LED imply LED_GPIO + imply SPI + imply DESIGNWARE_SPI + imply SPI_FLASH_WINBOND + imply DM_MTD + imply SPI_FLASH_MTD + imply CMD_MTD + imply ENV_IS_IN_SPI_FLASH + imply MMC + imply MMC_BROKEN_CD + imply MMC_SPI endif
configs/sipeed_maix_bitm_defconfig +8 -0
@@ -1,6 +1,14 @@ CONFIG_RISCV=y +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x1000 +CONFIG_ENV_OFFSET=0x7C000 +CONFIG_ENV_OFFSET_REDUND=0x7E000 CONFIG_TARGET_SIPEED_MAIX=y CONFIG_ARCH_RV64I=y +CONFIG_USE_BOOTCOMMAND=y +CONFIG_BOOTCOMMAND="sf probe;mtd read kernel 80000000;go 80000000" +CONFIG_MTDIDS_DEFAULT="nor0=spi3.0" +CONFIG_MTDPARTS_DEFAULT="spi3.0:496k(u-boot),16k(env),5632k(kernel),10240k(data)" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y # CONFIG_NET is not set # CONFIG_INPUT is not set
doc/board/sipeed/maix.rst +61 -33
109 lines not on this page · raw message
Signature · 1 line
2.25.0