2.4 -> 2.6: problem probing PCI
Hi,
before digging into the lower ppc specific code myself, I thought to ask and describe my problem here first. I am currently porting a 2.4 based embedded solution to a 2.6 kernel (basically for the fun of it) and have come accross the following:
When probing the PCI bus (of an embedded solution DBG enabled; 2.6.9):
PCI: Probing PCI hardware
PCI: bridge rsrc 0..bfffff (100), parent c0172188
PCI: reparented dma1 [0..1f] under PCI host bridge
PCI: reparented pic1 [20..3f] under PCI host bridge
PCI: reparented timer [40..5f] under PCI host bridge
PCI: reparented dma page reg [80..8f] under PCI host bridge
PCI: reparented pic2 [a0..bf] under PCI host bridge
PCI: reparented dma2 [c0..df] under PCI host bridge
PCI: bridge rsrc 80000000..fcffffff (200), parent c017216c PCI:0000:00:00.0: Resource 1: 00000000-00000fff (f=3D200)
PCI: Cannot allocate resource region 1 of device 0000:00:00.0
PCI: parent is c01b6054: 80000000-fcffffff (f=3D200) PCI:0000:00:10.0: Resource 0: bffff000-bfffffff (f=3D200) PCI:0000:00:10.0: Resource 1: 00bfffc0-00bfffff (f=3D101) PCI:0000:00:10.0: Resource 2: bffc0000-bffdffff (f=3D200) PCI:0000:00:11.0: Resource 0: bffbf000-bffbffff (f=3D200) PCI:0000:00:11.0: Resource 1: 00bfff80-00bfffbf (f=3D101) PCI:0000:00:11.0: Resource 2: bff80000-bff9ffff (f=3D200) PCI:0000:00:12.0: Resource 0: bf800000-bfbfffff (f=3D1208) PCI:0000:00:12.0: Resource 1: bf000000-bf7fffff (f=3D200) PCI:0000:00:12.0: Resource 2: 00bfff70-00bfff7f (f=3D101) PCI:0000:00:13.0: Resource 0: 00bfff60-00bfff6f (f=3D101) PCI:0000:00:13.0: Resource 1: befffff0-beffffff (f=3D200)
There is a problem with an FPGA register map (I assume) since:
ppc2fpga: BAR 0 (0xbfff60-0xbfff6f), len=3D16, flags=3D0x000101
ppc2fpga: BAR 1 (0xbefffff0-0xbeffffff), len=3D16, flags=3D0x000200
ppc2fpga: remapped 0xbfff60 with size 16 to 0xc3004f60
On a 2.4.28-rc1, this reads (same hardware):
ppc2fpga: BAR 0 (0xfebfff40-0xfebfff5f), len=3D32, flags=3D0x000101
ppc2fpga: BAR 1 (0xbefffff0-0xbeffffff), len=3D16, flags=3D0x000200
ppc2fpga: remapped 0xfebfff40 with size 32 to 0xfebfff40
This last one has the correct behaviour and is the one currently being installed. Both the size and the address is wrong. When I read data from the FPGA, I get 0xFF while it should be ASCII information (the FPGA is the PPC watchdog).
My obvious question is now: any pointers in how to proceed in debugging this or possible reasons for this change in behaviour?
--=20
ash nazg durbatul=FBk, ash nazg gimbatul,
ash nazg thrakatul=FBk agh burzum-ishi krimpatul
I am currently comparing the 2.6.9 (failing code) PCI DBG output with the 2.4.28-rc1 (working code) DBG output:
2.6.9:
Quoted 15 lines
PCI: Probing PCI hardware
PCI: bridge rsrc 0..bfffff (100), parentc0172188
PCI: reparented dma1 [0..1f] under PCI host bridge
PCI: reparented pic1 [20..3f] under PCI host bridge
PCI: reparented timer [40..5f] under PCI host bridge
PCI: reparented dma page reg [80..8f] under PCI host bridge
PCI: reparented pic2 [a0..bf] under PCI host bridge
PCI: reparented dma2 [c0..df] under PCI host bridge
PCI: bridge rsrc 80000000..fcffffff (200), parentc017216cPCI:0000:00:00.0: Resource 1: 00000000-00000fff (f=3D200)
PCI: Cannot allocate resource region 1 of device 0000:00:00.0
PCI: parent isc01b6054: 80000000-fcffffff (f=3D200) PCI:0000:00:10.0: Resource 0: bffff000-bfffffff (f=3D200) PCI:0000:00:10.0: Resource 1: 00bfffc0-00bfffff (f=3D101) PCI:0000:00:10.0: Resource 2: bffc0000-bffdffff (f=3D200)
Quoted 8 lines
PCI:0000:00:11.0: Resource 0: bffbf000-bffbffff (f=3D200) PCI:0000:00:11.0: Resource 1: 00bfff80-00bfffbf (f=3D101) PCI:0000:00:11.0: Resource 2: bff80000-bff9ffff (f=3D200) PCI:0000:00:12.0: Resource 0: bf800000-bfbfffff (f=3D1208) PCI:0000:00:12.0: Resource 1: bf000000-bf7fffff (f=3D200) PCI:0000:00:12.0: Resource 2: 00bfff70-00bfff7f (f=3D101) PCI:0000:00:13.0: Resource 0: 00bfff60-00bfff6f (f=3D101) PCI:0000:00:13.0: Resource 1: befffff0-beffffff (f=3D200)
2.4.28-rc1
PCI: Probing PCI hardware
PCI:00:00.0 Resource 1 [00000000-00000fff] is unassigned Fixup res 1 (101) of dev 00:10.0: bfffc0 -> febfffc0 Fixup res 1 (101) of dev 00:11.0: bfff80 -> febfff80 Fixup res 2 (101) of dev 00:12.0: bfff70 -> febfff70 Fixup res 0 (101) of dev 00:13.0: bfff60 -> febfff60
PCI: bridge rsrc fe000000..febfffff (100), parent c012aee8
PCI: bridge rsrc 80000000..fcffffff (200), parent c012aecc PCI:00:10.0: Resource 0: bffff000-bfffffff (f=3D200) PCI:00:10.0: Resource 1: febfffc0-febfffff (f=3D101) PCI:00:10.0: Resource 2: bffc0000-bffdffff (f=3D200) PCI:00:11.0: Resource 0: bffbf000-bffbffff (f=3D200) PCI:00:11.0: Resource 1: febfff80-febfffbf (f=3D101) PCI:00:11.0: Resource 2: bff80000-bff9ffff (f=3D200) PCI:00:12.0: Resource 0: bf800000-bfbfffff (f=3D1208) PCI:00:12.0: Resource 1: bf000000-bf7fffff (f=3D200) PCI:00:12.0: Resource 2: febfff70-febfff7f (f=3D101) PCI:00:13.0: Resource 0: febfff60-febfff6f (f=3D101) PCI:00:13.0: Resource 1: befffff0-beffffff (f=3D200)
The first important difference is that a number of fixups are no longer performed in the 2.6.9 kernel; which account for the differences in the PCI address ranges.
The problem seems to be in=20arch/ppc/kernel/pci.c
When comparing (but not yet fixed), some minor changes have been made:
line 16 changed from
if (!res->start || res->end =3D=3D 0xffffffff) {
to
if (res->end =3D=3D 0xffffffff) {
which disables the flow to enter the body in this case.
another relevant piece of code that gets me into troubles is the computation of the offset
} else if (res->flags & IORESOURCE_IO) {
offset =3D (unsigned long) hose->io_base_virt;
- isa_io_base;
}both values are equal to 0xfe000000, giving a final offset of 0 and no adjustment.
I tried commenting out 'isa_io_base' but this gets me in resource allocation conflicts later on (even though I get the ranges identical to the ones in the 2.4.28 kernel).
Anyway, insights are welcome, I'm still investigating...
--=20
ash nazg durbatul=FBk, ash nazg gimbatul,
ash nazg thrakatul=FBk agh burzum-ishi krimpatul
Quoted 1 line
Anyway, insights are welcome, I'm still investigating...
Found it, I used the wrong arc/ppc/platforms file after too zealous cleanup of the code. I need some final testing but it looks like this will be the only file that needs update (considering the PCI mapping and scanning).
--=20
ash nazg durbatul=FBk, ash nazg gimbatul,
ash nazg thrakatul=FBk agh burzum-ishi krimpatul