did 2.4 messed up lilo?
I'm not sure whether this problem is related
to 2.4 kernel.
I've installed kernels 2.4.0-prex to 2.4.1 on
the following machines. All are now running 2.4.1. Judging from my past experience posting here I'm giving much information
- compaq prolinea p-90 de4x5 driver 1 gig quantum drive cmd 640 controller
- dell optiplex p-133 hp-pcplus driver 8 gig seagate cmd 640 controller
- ibm p-133 de4x5 driver maxtor 4 gig
All partitions are reiserfs. except for dell box linux is the only system and root is on /dev/hda1. dell's root is on /dev/hda7 with /dev/hda1 occupied by the unmentionable.
Soon after I've installed 2.4.xx lilo stopped working properly. Unfortunately I'm not sure whether it started with as soon as any 2.4 installed or on subsequent installation.
What happens is the lilo does not give you any prompt any more. My /etc/lilo.conf, of course, have proper timeout parameter which were working before with 2.2.18.
On compaq it does not even boot at all from hard drive. I'm using a floopy to boot and run that box. Others just boot right into the default specified in /etc/lilo.conf
I would not be complaining if it weren't for the fact that lilo does not obey kernel parameters any more. On ibm box I need to append="hdc=ide-scsi" to use my cd-rw drive. The system boots with the right kernel but I cannot use cd-rw because it apparently is not looking at the kernel parameters.
I also am no good at installing lilo on a floppy.
I apologize in advance if this problem is not 2.4 related.
FYI I've also installed 2.4 on celeron 566 without this problem. I'm just not running 2.4 on this one just because I cannot make the graphics card operate under 2.4
Thanks in advance
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
Quoted 3 lines · On Friday, February 02, 2001 03:36:18 PM -0500 [email protected] wrote:
I'm not sure whether this problem is related
to 2.4 kernel.
I suspect it is a reiserfs problem, and that you are using lilo older than 21.6. Are you mounting /boot with -o notail?
Regardless, I'm willing to bet upgrading to lilo 21.6 will solve this. It calls an ioctl reiserfs provides to unpack small files, and I've seen it fix this exact problem on one of my devel boxes (no lilo prompt, append lines in lilo.conf ignored).
-chris
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
Quoted 8 lines · Chris Mason
Quoted 3 lines · On Friday, February 02, 2001 03:36:18 PM -0500 [email protected] wrote:
I'm not sure whether this problem is related
to 2.4 kernel.
Quoted 7 lines
I suspect it is a reiserfs problem, and that you are using lilo older than 21.6. Are you mounting /boot with -o notail?
Regardless, I'm willing to bet upgrading to lilo 21.6 will solve this. It calls an ioctl reiserfs provides to unpack small files, and I've seen it fix this exact problem on one of my devel boxes (no lilo prompt, append lines in lilo.conf ignored).
I also found this patch for lilo 21.6:
http://industrial-linux.org/distro/download/lilo-21.6-glibc-2.2-reiserfs.patch
Perhaps someone familiar with the lilo and reiserfs code could explain whether or not this patch is really needed.
Miles
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
Hmm. I just downloaded the lilo 21.6 source and the patch appears to have
already been applied. I got 21.6 from:
http://ftp.cnr.it/Linux/system/boot/lilo/lilo-21.6.1.tar.gz
Quoted 22 lines · Miles Lane
Quoted 8 lines · Chris Mason
Quoted 3 lines · On Friday, February 02, 2001 03:36:18 PM -0500 [email protected] wrote:
I'm not sure whether this problem is related
to 2.4 kernel.Quoted 7 lines
I suspect it is a reiserfs problem, and that you are using lilo older than 21.6. Are you mounting /boot with -o notail?
Regardless, I'm willing to bet upgrading to lilo 21.6 will solve this. It calls an ioctl reiserfs provides to unpack small files, and I've seen it fix this exact problem on one of my devel boxes (no lilo prompt, append lines in lilo.conf ignored).
I also found this patch for lilo 21.6:
http://industrial-linux.org/distro/download/lilo-21.6-glibc-2.2-reiserfs.patch
Quoted 8 lines
Perhaps someone familiar with the lilo and reiserfs code could explain whether or not this patch is really needed.
Miles
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
I've now installed 21.6 downloaded from metlab and all seems to be ok now... well at least the dell box.. compaq boot sector may have been blown off for some reason..it won't boot at all athough this time it's a different way of being stuck like LI instead of LILO. I will try ibm box in the morning when the traffic is light.
Quoted 4 lines · Miles Lane
Hmm. I just downloaded the lilo 21.6 source and the patch appears to have
already been applied. I got 21.6 from:
Quoted 33 lines
http://ftp.cnr.it/Linux/system/boot/lilo/lilo-21.6.1.tar.gzQuoted 30 lines · Miles Lane
Quoted 8 lines · Chris Mason
Quoted 3 lines · On Friday, February 02, 2001 03:36:18 PM -0500 [email protected] wrote:
I'm not sure whether this problem is related
to 2.4 kernel.Quoted 7 lines
I suspect it is a reiserfs problem, and that you are using lilo older than 21.6. Are you mounting /boot with -o notail?
Regardless, I'm willing to bet upgrading to lilo 21.6 will solve this. It calls an ioctl reiserfs provides to unpack small files, and I've seen it fix this exact problem on one of my devel boxes (no lilo prompt, append lines in lilo.conf ignored).
I also found this patch for lilo 21.6:
http://industrial-linux.org/distro/download/lilo-21.6-glibc-2.2-reiserfs.patch
Perhaps someone familiar with the lilo and reiserfs code could explain whether or not this patch is really needed.
Miles
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
Just to let everyone knows that 21.6 also
fix the problem on ibm box. I can now
mount cdr drive. Thank you.
Quoted 11 lines · On Sat, Feb 03, 2001 at 12:14:09AM -0500, [email protected] wrote:
I've now installed 21.6 downloaded from metlab and all seems to be ok now... well at least the dell box.. compaq boot sector may have been blown off for some reason..it won't boot at all athough this time it's a different way of being stuck like LI instead of LILO. I will try ibm box in the morning when the traffic is light.
Quoted 38 lines
Quoted 37 lines · Miles Lane
Hmm. I just downloaded the lilo 21.6 source and the patch appears to have
already been applied. I got 21.6 from:http://ftp.cnr.it/Linux/system/boot/lilo/lilo-21.6.1.tar.gzQuoted 30 lines · Miles Lane
Quoted 8 lines · Chris Mason
Quoted 3 lines · On Friday, February 02, 2001 03:36:18 PM -0500 [email protected] wrote:
I'm not sure whether this problem is related
to 2.4 kernel.Quoted 7 lines
I suspect it is a reiserfs problem, and that you are using lilo older than 21.6. Are you mounting /boot with -o notail?
Regardless, I'm willing to bet upgrading to lilo 21.6 will solve this. It calls an ioctl reiserfs provides to unpack small files, and I've seen it fix this exact problem on one of my devel boxes (no lilo prompt, append lines in lilo.conf ignored).
I also found this patch for lilo 21.6:
http://industrial-linux.org/distro/download/lilo-21.6-glibc-2.2-reiserfs.patch
Perhaps someone familiar with the lilo and reiserfs code could explain whether or not this patch is really needed.
Miles
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/