Skip to contentSkip to conversation

ATAPI CDRW which doesn't work

DISCUSSION [email protected] 1 participant 1 message Feb 4, 2001

lore
Share & tools
lore
#0 lore raw

You were my best hope, cause i did something similar for a Hp 720c on parallel port, and it worked. I did excatly what you've just said.
But the whole thing still doesn't work properly.

I finally could mount the device, then read the first root directory. But couldn't get more... always got what you see at the end of the error message.. I/O error, which resulted in no files appearing from a 'ls' command.

I've got those kind of message now :

Feb  4 07:18:35 Line kernel: scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Read (10) 00 00 00 00 2e 00 00 01 00 
Feb  4 07:18:35 Line kernel: SCSI host 0 abort (pid 0) timed out - resetting
Feb  4 07:18:35 Line kernel: SCSI bus is being reset for host 0 channel 0.
Feb  4 07:18:35 Line kernel: hdb: ATAPI reset complete
Feb  4 07:18:35 Line kernel: scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Read (10) 00 00 00 00 2e 00 00 01 00 
Feb  4 07:18:35 Line kernel: SCSI host 0 abort (pid 0) timed out - resetting
Feb  4 07:18:35 Line kernel: SCSI bus is being reset for host 0 channel 0.
Feb  4 07:18:37 Line kernel: hdb: irq timeout: status=0xd0 { Busy }
Feb  4 07:18:41 Line kernel: scsi0: ERROR on channel 0, id 0, lun 0, CDB: Request Sense 00 00 00 40 00 
Feb  4 07:18:41 Line kernel: Info fld=0x0, Current sd0b:00: sense key Medium Error
Feb  4 07:18:41 Line kernel:  I/O error: dev 0b:00, sector 184
Feb  4 07:20:09 Line kernel: scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Read (10) 00 00 00 00 2e 00 00 01 00 
Feb  4 07:20:09 Line kernel: hdb: irq timeout: status=0xd0 { Busy }
Feb  4 07:20:09 Line kernel: hdb: ATAPI reset complete
Feb  4 07:20:09 Line kernel: hdb: irq timeout: status=0xd0 { Busy }
Feb  4 07:20:09 Line kernel: hdb: ATAPI reset complete
Feb  4 07:20:10 Line kernel: hdb: irq timeout: status=0xd0 { Busy }
Feb  4 07:20:10 Line kernel: scsi0 channel 0 : resetting for second half of retries.
Feb  4 07:20:10 Line kernel: SCSI bus is being reset for host 0 channel 0.
Feb  4 07:20:10 Line kernel: hdb: status timeout: status=0xd0 { Busy }
Feb  4 07:20:10 Line kernel: hdb: drive not ready for command
Feb  4 07:20:21 Line kernel: hdb: ATAPI reset complete
Feb  4 07:20:22 Line kernel: Device 0b:00 not ready.
Feb  4 07:20:22 Line kernel:  I/O error: dev 0b:00, sector 184
Quoted 8 lines · Marko Kreen
Quoted 6 lines · On Sat, Feb 03, 2001 at 11:05:44PM +0100, [email protected] wrote:

Hi,

I've never could make this CDRW ATAPI to work, if someone could provide me any clue about the baby. I just said that people on the kernel mailing list may care of its but. It looks like the baby didn't even noticed. ;-)

Quoted 10 lines

Compile in options 'SCSI generic', 'SCSI cdrom and 'SCSI emulation support' then add 'hdb=scsi' to kernel parameters.

Now you can use it as SCSI cdrom, and cd-writers recognize it too. Eg. for cdrecord you should probably put 'dev=0,0,0' to command line (I assume you have no other SCSI controller).

Signature · 1 line
marko

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/