Skip to contentSkip to conversation

Mucho timeouts on USB

DISCUSSION John Cavan 4 participants 6 messages Feb 10, 2001

lore
Share & tools
lore

John Cavan

author
#0 lore raw

Hi,

Just got a D-Link USB radio (R100) and I'm seeing lots of timeouts with it. I've seen this through the last few 2.4.1+ and -ac+ kernels.

Current config:

Dual P3-500 w/ 512mb of RAM
Tyan Tiger 133 mobo with VIA chipset, onboard USB
Kernel 2.4.1-ac9 compiled with egcs-1.1.2

The only thing funky is that three devices are sharing an interrupt:

CPU0 CPU1

  0:     216690     219652    IO-APIC-edge  timer
  1:       3564       3816    IO-APIC-edge  keyboard
  2:          0          0          XT-PIC  cascade
  3:          7         20    IO-APIC-edge  serial
  5:       1017       1135   IO-APIC-level  EMU10K1
  8:          0          1    IO-APIC-edge  rtc
 11:      22978      22756   IO-APIC-level  aic7xxx, eth0, usb-uhci
 12:      64220      63272    IO-APIC-edge  PS/2 Mouse
 14:      12132      12810    IO-APIC-edge  ide0
 15:          3         10    IO-APIC-edge  ide1
NMI:     436327     436327 
LOC:     436151     436128 
ERR:          0

The ethernet card is a 3Com 3c905, the SCSI card is Adaptec 7892B (19160 card). No problems with either as far as I can tell, but one of these modules may not be playing nice with interrupt sharing.

The messages:

usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 17:33:47 Feb 9 2001 usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1 usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110) usb.c: USB device 3 (vend/prod 0x4b4/0x1002) is not claimed by any active driver.
usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/

#1 lore raw

I'm seeing a similar usb timeout message here
with an HP 5200C usb scanner, e.g:

usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout

My config:

AMD-K6 450 on ASUS P5 mb
256 MB RAM, Ali chipset
Red Hat 7.0 updated, kernel 2.4.1-ac8

jjs

Quoted 54 lines · John Cavan

Hi,

Just got a D-Link USB radio (R100) and I'm seeing lots of timeouts with it. I've seen this through the last few 2.4.1+ and -ac+ kernels.

Current config:

Dual P3-500 w/ 512mb of RAM
Tyan Tiger 133 mobo with VIA chipset, onboard USB
Kernel 2.4.1-ac9 compiled with egcs-1.1.2

The only thing funky is that three devices are sharing an interrupt:

CPU0 CPU1

  0:     216690     219652    IO-APIC-edge  timer
  1:       3564       3816    IO-APIC-edge  keyboard
  2:          0          0          XT-PIC  cascade
  3:          7         20    IO-APIC-edge  serial
  5:       1017       1135   IO-APIC-level  EMU10K1
  8:          0          1    IO-APIC-edge  rtc
 11:      22978      22756   IO-APIC-level  aic7xxx, eth0, usb-uhci
 12:      64220      63272    IO-APIC-edge  PS/2 Mouse
 14:      12132      12810    IO-APIC-edge  ide0
 15:          3         10    IO-APIC-edge  ide1
NMI:     436327     436327
LOC:     436151     436128
ERR:          0

The ethernet card is a 3Com 3c905, the SCSI card is Adaptec 7892B (19160 card). No problems with either as far as I can tell, but one of these modules may not be playing nice with interrupt sharing.

The messages:

usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 17:33:47 Feb 9 2001 usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1 usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110) usb.c: USB device 3 (vend/prod 0x4b4/0x1002) is not claimed by any active driver.
usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout

Quoted 8 lines

usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/

#2 lore raw
In reply to John Cavan
Quoted 48 lines · John Cavan

Just got a D-Link USB radio (R100) and I'm seeing lots of timeouts with it. I've seen this through the last few 2.4.1+ and -ac+ kernels.

Current config:

Dual P3-500 w/ 512mb of RAM
Tyan Tiger 133 mobo with VIA chipset, onboard USB
Kernel 2.4.1-ac9 compiled with egcs-1.1.2

The only thing funky is that three devices are sharing an interrupt:

CPU0 CPU1

  0:     216690     219652    IO-APIC-edge  timer
  1:       3564       3816    IO-APIC-edge  keyboard
  2:          0          0          XT-PIC  cascade
  3:          7         20    IO-APIC-edge  serial
  5:       1017       1135   IO-APIC-level  EMU10K1
  8:          0          1    IO-APIC-edge  rtc
 11:      22978      22756   IO-APIC-level  aic7xxx, eth0, usb-uhci
 12:      64220      63272    IO-APIC-edge  PS/2 Mouse
 14:      12132      12810    IO-APIC-edge  ide0
 15:          3         10    IO-APIC-edge  ide1
NMI:     436327     436327 
LOC:     436151     436128 
ERR:          0

The ethernet card is a 3Com 3c905, the SCSI card is Adaptec 7892B (19160 card). No problems with either as far as I can tell, but one of these modules may not be playing nice with interrupt sharing.

The messages:

usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 17:33:47 Feb 9 2001 usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1 usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110) usb.c: USB device 3 (vend/prod 0x4b4/0x1002) is not claimed by any active driver.
usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout

Quoted 8 lines

usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout
usb.c: error getting string descriptor 0 (error=-110) usb_control/bulk_msg: timeout usb_control/bulk_msg: timeout usb_control/bulk_msg: timeout usb_control/bulk_msg: timeout usb_control/bulk_msg: timeout

Looks like an IRQ routing problem. We've seen a lot of these and I'm not sure why the current IRQ routing code doesn't work correctly on some systems but works fine on others.

Does anyone have any idea why it's not working for him?

JE

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/

#3 lore raw
In reply to John Cavan
Quoted 6 lines · John Cavan

Current config:

Dual P3-500 w/ 512mb of RAM
Tyan Tiger 133 mobo with VIA chipset, onboard USB
Kernel 2.4.1-ac9 compiled with egcs-1.1.2

This motherboard does not currently work with USB in SMP mode, unless you boot with "noapic" on the command line. People are working on it, but it's slow going.

FWIW, Windows2000 refuses to also work for this VIA USB chipset :)

greg k-h

Signature · 6 lines
greg@(kroah|wirex).com
http://immunix.org/~greg
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/
author
#4 lore raw
In reply to John Cavan
Quoted 5 lines · Greg KH
Quoted 3 lines · John Cavan

Current config:

Quoted 7 lines
Quoted 3 lines

Dual P3-500 w/ 512mb of RAM
Tyan Tiger 133 mobo with VIA chipset, onboard USB
Kernel 2.4.1-ac9 compiled with egcs-1.1.2

This motherboard does not currently work with USB in SMP mode, unless you boot with "noapic" on the command line. People are working on it, but it's slow going.

I'll try that.

Quoted 1 line

FWIW, Windows2000 refuses to also work for this VIA USB chipset :)

According to Tyan, the issue should be fixed with the last BIOS update. I'm up to date in the BIOS (and I really wish that these guys would create a flash program that was OSS so I could avoid DOS), but one of the work arounds suggested was setting IRQ 12 to ISA/Legacy for Windows 2000. Didn't seem to cut it.

Thanks,
John
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/

author
#5 lore raw
In reply to John Cavan
Quoted 5 lines · Greg KH
Quoted 3 lines · John Cavan

Current config:

Quoted 7 lines
Quoted 3 lines

Dual P3-500 w/ 512mb of RAM
Tyan Tiger 133 mobo with VIA chipset, onboard USB
Kernel 2.4.1-ac9 compiled with egcs-1.1.2

This motherboard does not currently work with USB in SMP mode, unless you boot with "noapic" on the command line. People are working on it, but it's slow going.

That did the trick! Thanks alot.

Nice too, first song played by Rush. :o)

John
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/