2.2.17 Lockup and ATA-66/100 forced bit set (WARNING)
I've enabled the higher performance features for my ATA drive by getting 2.2.17, applying Andre Hendrick's IDE patch, adding:
append="idebus=66 ide0=ata66"
to lilo.conf. I was told that Alan's patches from here:
ftp.kernel.org/pub/linux/kernel/people/alan
should be used. Is this true if I used Andre's patch? Is the warning message in my bootlog anything to worry about? The board is an ABIT KT7A w/ KT133A chipset.
Also, the machine locked up once (hard, couldn't connect via network). I am using the Matrox G450 beta driver with XF 4.0.2 though. Maybe that was the cause?
Thanks,
Mike
syslogd 1.3-3: restart.
syslog: syslogd startup succeeded
kernel: klogd 1.3-3, log source = /proc/kmsg started.
syslog: klogd startup succeeded
kernel: Inspecting /boot/System.map
kernel: Loaded 6567 symbols from /boot/System.map.
kernel: Symbols match kernel version 2.2.17.
kernel: No module symbols loaded.
kernel: Linux version 2.2.17 (root@nano) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #2 Wed Feb 21 02:33:48 EST 2001
kernel: Detected 900061 kHz processor.
kernel: ide_setup: idebus=66
kernel: ide_setup: ide0=ata66
kernel: Console: colour VGA+ 80x25
I thought the BogoMIPS sort of went along with the CPU MHz?
kernel: Calibrating delay loop... 1795.69 BogoMIPS
kernel: Memory: 257852k/262080k available (976k kernel code, 412k reserved, 2796k data, 44k init)
kernel: Dentry hash table entries: 32768 (order 6, 256k)
kernel: Buffer cache hash table entries: 262144 (order 8, 1024k)
kernel: Page cache hash table entries: 65536 (order 6, 256k)
kernel: CPU: L1 I Cache: 64K L1 D Cache: 64K
kernel: CPU: L2 Cache: 256K
kernel: CPU: AMD Athlon(tm) Processor stepping 02
kernel: Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
kernel: Checking 'hlt' instruction... OK.
kernel: POSIX conformance testing by UNIFIX
kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb430
kernel: PCI: Using configuration type 1
kernel: PCI: Probing PCI hardware
kernel: Linux NET4.0 for Linux 2.2
kernel: Based upon Swansea University Computer Society NET3.039
kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0.
kernel: NET4: Linux TCP/IP 1.0 for NET4.0
kernel: IP Protocols: ICMP, UDP, TCP
kernel: TCP: Hash tables configured (ehash 262144 bhash 65536)
kernel: Starting kswapd v 1.5
kernel: Detected PS/2 Mouse Port.
kernel: Serial driver version 4.27 with no serial options enabled
kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
kernel: pty: 256 Unix98 ptys configured
kernel: Uniform Multi-Platform E-IDE driver Revision: 6.30
kernel: ide: Assuming 66MHz system bus speed for PIO modes
kernel: VP_IDE: IDE controller on PCI bus 00 dev 39
kernel: VP_IDE: chipset revision 6
kernel: VP_IDE: not 100% native mode: will probe irqs later
This is what I'm worried about right here:
kernel: VP_IDE: ATA-66/100 forced bit set (WARNING)!! kernel: ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio kernel: ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio kernel: hda: IBM-DTLA-307030, ATA DISK drive kernel: hdc: PLEXTOR CD-R PX-W1210A, ATAPI CDROM drive kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 kernel: ide1 at 0x170-0x177,0x376 on irq 15 kernel: hda: IBM-DTLA-307030, 29314MB w/1916kB Cache, CHS=3737/255/63, UDMA(100) kernel: Floppy drive(s): fd0 is 1.44M kernel: FDC 0 is a post-1991 82077
And why do I have 8 cdroms?
kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices kernel: scsi : 1 host. kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02 kernel: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02 kernel: Detected scsi CD-ROM sr1 at scsi0, channel 0, id 0, lun 1 kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02 kernel: Detected scsi CD-ROM sr2 at scsi0, channel 0, id 0, lun 2 kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02 kernel: Detected scsi CD-ROM sr3 at scsi0, channel 0, id 0, lun 3 kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02 kernel: Detected scsi CD-ROM sr4 at scsi0, channel 0, id 0, lun 4 kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02 kernel: Detected scsi CD-ROM sr5 at scsi0, channel 0, id 0, lun 5 kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02 kernel: Detected scsi CD-ROM sr6 at scsi0, channel 0, id 0, lun 6 kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02 kernel: Detected scsi CD-ROM sr7 at scsi0, channel 0, id 0, lun 7 kernel: scsi : detected 8 SCSI generics 8 SCSI cdroms total. kernel: sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray kernel: Uniform CD-ROM driver Revision: 3.11 kernel: sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray kernel: sr2: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray kernel: sr3: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray kernel: sr4: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray kernel: sr5: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray kernel: sr6: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray kernel: sr7: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray kernel: 3c59x.c 16Aug00 Donald Becker and others http://www.scyld.com/network/vortex.html kernel: eth0: 3Com 3c905C Tornado at 0xec00, 00:01:02:cf:5f:18, IRQ 11 kernel: 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface. kernel: MII transceiver found at address 24, status 782d. kernel: Enabling bus-master transmits and whole-frame receives. kernel: Partition check: kernel: hda: hda1 hda2 kernel: VFS: Mounted root (ext2 filesystem) readonly. kernel: Freeing unused kernel memory: 44k freed kernel: Adding Swap: 136544k swap-space (priority -1) identd: identd startup succeeded atd: atd startup succeeded crond: crond startup succeeded inet: inetd startup succeeded lpd: lpd startup succeeded
lpd[457]: restarted
rc.sysinit: Mounting proc filesystem succeeded
sysctl: net.ipv4.ip_forward = 0
sysctl: net.ipv4.conf.all.rp_filter = 1
sysctl: net.ipv4.ip_always_defrag = 0
Here's another little error?
sysctl: error: 'kernel.sysrq' is an unknown key
rc.sysinit: Configuring kernel parameters succeeded
date: Wed Feb 21 17:38:31 EST 2001
rc.sysinit: Setting clock : Wed Feb 21 17:38:31 EST 2001 succeeded rc.sysinit: Loading default keymap succeeded
rc.sysinit: Activating swap partitions succeeded
succeeded
fsck: /dev/hda1: clean, 62090/788704 files, 279756/1574362 blocks rc.sysinit: Checking root filesystem succeeded
rc.sysinit: Remounting root filesystem in read-write mode succeeded rc.sysinit: Finding module dependencies succeeded
rc.sysinit: Checking filesystems succeeded
rc.sysinit: Mounting local filesystems succeeded
rc.sysinit: Turning on user and group quotas for local filesystems succeeded rc.sysinit: Enabling swap space succeeded
init: Entering runlevel: 5
sysctl: net.ipv4.ip_forward = 0
sysctl: net.ipv4.conf.all.rp_filter = 1
sysctl: net.ipv4.ip_always_defrag = 0
Mmm, here's that sysctl stuff again?
sysctl: error: 'kernel.sysrq' is an unknown key
network: Setting network parameters succeeded
Err, I have lot's of errors!
ifup: SIOCADDRT: Network is unreachable
network: Bringing up interface lo succeeded
network: Bringing up interface eth0 succeeded
portmap: portmap startup succeeded
nfslock: rpc.lockd startup succeeded
nfslock: rpc.statd startup succeeded
random: Initializing random number generator succeeded
netfs: Mounting other filesystems succeeded
keytable: Loading keymap:
keytable: Loading /usr/lib/kbd/keymaps/i386/qwerty/us.kmap.gz
keytable: Loading system font:
rc: Starting keytable succeeded
sendmail: sendmail startup succeeded
PAM_pwdb[533]: (gdm) session opened for user miallen by (uid=0) gdm[533]: gdm_slave_session_start: miallen on :0 PAM_pwdb[615]: (su) session opened for user root by miallen(uid=500)
Signature · 1 line
signature pending
Quoted 5 lines · Michael B. Allen
And why do I have 8 cdroms?
kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices kernel: scsi : 1 host. kernel: Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.07 kernel: Type: CD-ROM ANSI SCSI revision: 02
It's an old old bug with the ide-scsi lun probing code. Dont know if 2.4.x fixed it yet. Solution -- disable lun probing in scsi config.
-Dan
Quoted 5 lines · Wayne Whitney
Quoted 1 line
append="idebus=66 ide0=ata66"
The idebus=66 part is incorrect. This option refers to the clock of the PCI bus the IDE controller is on and should rarely be changed from the default of 33MHz (i.e., only if you are overclocking the PCI bus).
Ah, well I just added that based on the end of this boot message:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Quoted 7 lines
Quoted 1 line
kernel:
VP_IDE: ATA-66/100 forced bit set (WARNING)!!I'm sure this is just telling you that you passed the ide0=ata66 parameter. Usually it is best not to do this--the driver should run your chipset/drive as fast as possible without 'forcing' the configuration. Of course, testing with hdparm -t is considered the definitive way to check how fast the interface is running.
If I don't add it hdparm -t /dev/hda reports:
Timing buffered disk reads: 64 MB in 16.46 seconds = 3.89 MB/sec
Then if I do hdparm -d1 -X66 /dev/hda I get:
/dev/hda:
setting using_dma to 1 (on)
setting xfermode to 66 (UltraDMA mode2)
using_dma = 1 (on)
[root@nano /root]# hdparm -t /dev/hda
/dev/hda:
Timing buffered disk reads: 64 MB in 4.04 seconds = 15.84 MB/sec
Now if I add it via append, reboot and do hdparm -t I get:
Timing buffered disk reads: 64 MB in 3.70 seconds = 17.30 MB/sec
This last difference is consistently better. Weird.
All your other bets were right too.
Thanks Wayne,
Mike
Signature · 1 line
signature pending
Quoted 7 lines
I've enabled the higher performance features for my ATA drive by getting 2.2.17, applying Andre Hendrick's IDE patch, adding:
append="idebus=66 ide0=ata66"
to lilo.conf. I was told that Alan's patches from here:
should be used. Is this true if I used Andre's patch? Is the warning message in my bootlog anything to worry about? The board is an ABIT KT7A w/ KT133A chipset.
Alan = kernel, Andre = IDE. 2.2.18 (kernel) + ide.2.2.18.1221 (IDE patch) + 2.2.19pre8 (kernel patch). See samples below.
Quoted 3 lines
Also, the machine locked up once (hard, couldn't connect via network). I am using the Matrox G450 beta driver with XF 4.0.2 though. Maybe that was the cause?
Ensoniq AudioPCI (ES1370) was problematic if I tried to assign IRQ5 on the KA7 (hard trailess lockups, all IRQ's migrated to 10 or 11 regardless of config, digital audio ScreamOfAgony), whereas IRQ 3 worked fine. Similar experiements with Intel chipset boards P3B-F & BP6 suffer no such issues so I assume it's VT82C686/ES1370 specific.
Abit KA7, 2.2.19pre8 + ide.2.2.18.1221
--------------------------------------
Linux version 2.2.19pre8+IDE (root@abit) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #6 Tue Feb 20
01:14:30 PST 2001
USER-provided physical RAM map:
USER: 0009f000 @ 00000000 (usable)
USER: 1ff00000 @ 00100000 (usable)
Detected 800063 kHz processor.ide_setup: idebus=33ide_setup: ide0=ata66ide_setup: ide1=ata66
Console: colour VGA+ 80x25
Calibrating delay loop... 1595.80 BogoMIPS
Memory: 517204k/524288k available (1116k kernel code, 412k reserved, 5508k data, 48k init)
Dentry hash table entries: 65536 (order 7, 512k)
Buffer cache hash table entries: 524288 (order 9, 2048k) Page cache hash table entries: 131072 (order 7, 512k)
CPU: L1 I Cache: 64K L1 D Cache: 64K
CPU: L2 Cache: 512K
CPU: AMD Athlon(tm) Processor stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([email protected])
PCI: PCI BIOS revision 2.10 entry at 0xfb4d0
PCI: Probing PCI hardware
...
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modesVP_IDE: IDE controller on PCI bus 00 dev 39VP_IDE: chipset revision 16VP_IDE: not 100% native mode: will probe irqs later
VT 8371
Chipset Core ATA-66VP_IDE: ATA-66/100 forced bit set (WARNING)!!
Split FIFO Configuration: 8 Primary buffers, threshold = 1/2
8 Second. buffers, threshold = 1/2
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide0: VIA Bus-Master (U)DMA Timing Config SuccessVP_IDE: ATA-66/100 forced bit set (WARNING)!!
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
ide1: VIA Bus-Master (U)DMA Timing Config Success
hda: IBM-DTLA-307020, ATA DISK drive
hdb: YAMAHA CRW4416E, ATAPI CDROM drive
hdc: IBM-DTLA-307020, ATA DISK drive
hdd: HP COLORADO 20GB, ATAPI TAPE drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: IBM-DTLA-307020, 19623MB w/1916kB Cache, CHS=2501/255/63, UDMA(66)
hdc: IBM-DTLA-307020, 19623MB w/1916kB Cache, CHS=39870/16/63, UDMA(66)
...
# lspci -v
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0391 (rev
02)
Flags: bus master, medium devsel, latency 0
Memory at d0000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 2.000:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device 8391 (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: d2000000-d3ffffff
Prefetchable memory behind bridge: d4000000-d5ffffff
Capabilities: [80] Power Management version 2
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev
22)
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Flags: bus master, stepping, medium devsel, latency 0
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
10) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at d000
Capabilities: [c0] Power Management version 2
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Flags: medium devsel
Capabilities: [68] Power Management version 2
Generic Socket7, 2.2.19pre8 + ide.2.2.18.1221
---------------------------------------------
Linux version 2.2.19pre8+IDE ([email protected]) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #3 Mon Feb 19 21:07:58 PST 2001
BIOS-provided physical RAM map:
BIOS-e820: 0009f000 @ 00000000 (usable)
BIOS-e820: 03f00000 @ 00100000 (usable)
Detected 166405 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 331.77 BogoMIPS
Memory: 63060k/65536k available (1044k kernel code, 412k reserved, 972k data, 48k init)
Dentry hash table entries: 8192 (order 4, 64k)
Buffer cache hash table entries: 65536 (order 6, 256k)
Page cache hash table entries: 16384 (order 4, 64k)
CPU: Intel Pentium 75 - 200 stepping 0c
Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK.
Intel Pentium with F0 0F bug - workaround enabled.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfb470
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00) Activating ISA DMA hang workarounds.
...
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller on PCI bus 00 dev 39VP_IDE: chipset revision 2VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VT 82C585 Apollo VP1/VPX
Chipset Core ATA-33
Split FIFO Configuration: 16 Primary buffers, threshold = 3/4
0 Second. buffers, threshold = 1/2
ide0: BM-DMA at 0x6000-0x6007, BIOS settings: hda:DMA, hdb:DMA
ide0: VIA Bus-Master (U)DMA Timing Config Success
hda: IBM-DJNA-370910, ATA DISK drive
hdb: BCD-F520D CD-ROM, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: IBM-DJNA-370910, 8693MB w/1966kB Cache, CHS=1108/255/63, (U)DMA
...
# lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT82C585VP [Apollo VP1/VPX]
(rev 10)
Flags: bus master, 66Mhz, medium devsel, latency 3200:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo VP] (rev 02)
Flags: bus master, medium devsel, latency 0
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
02) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at 6000
Memory at e1020000 (32-bit, non-prefetchable)Signature · 3 lines
timothymoore
bigfoot
com