parport not detected
The parallel port is not being detected on my ABIT KT7A KT133 w/ Athlon 900 running 2.2.17 w/ Hendricks IDE patches and RH 6.2. I tried most of the settings in the bios.
BIOS options are:
728/IRQ5
378/IRQ7
3BC/IRQ7
with the possible modes:
Normal
EPP
1.9 or 1.7 ECP DMA 3 or 1 ECP+EPP 1.9 or 1.7 and DMA 3 or 1
Of the above what's optimal?
[miallen@nano /etc]$ cat conf.modules
alias eth0 3c59x
alias char-major-6 parport_pc
alias parport_lowlevel parport_pc
Also, the module is loading with depmod:
[miallen@nano 0]$ for i in /proc/parport/0/*; do echo $i; cat $i; done /proc/parport/0/autoprobe/proc/parport/0/devices/proc/parport/0/hardware
base: 0x3bc irq: none dma: none modes: SPP
/proc/parport/0/irq
none
I also tried an options line in modules.conf. I believe it was:
options parport_pc io=0x3bc irq=7
That was reflected in /proc but no difference in actually "detecting" the parallel port. I did see the light come on on the printer once though. Also, if I build parpart into the kernel I get nothing but a hard lockup on 'Starting kswapd v 1.5'.
Any ideas?
Thanks,
Mike
Quoted 1 line
The parallel port is not being detected on my ABIT KT7A KT133 w/ Athlon
Also try comp.os.linux.hardware.
BIOS
----
278/irq5
378/irq7
EPP 1.9
.config
-------CONFIG_PARPORT=yCONFIG_PARPORT_PC=yCONFIG_PNP=yCONFIG_PNP_PARPORT=yCONFIG_PRINTER=yCONFIG_PRINTER_READBACK=y
kernal boot params
------------------
append="parport=0x378,7 parport=0x278,5"
options for /etc/rc.d/rc.local
------------------------------
# abort on error, careful error check, trust IRQ. # see tunelp(8) & /usr/src/linux/drivers/misc/lp.c
/usr/sbin/tunelp /dev/lp0 -a on -o on -T on/usr/sbin/tunelp /dev/lp1 -a on -o on -T on
looks like this (lp1 was powered down at boot time)
Feb 25 02:57:39 dell kernel: parport0: PC-style at 0x378, irq 7 [SPP,PS2,EPP] Feb 25 02:57:39 dell kernel: parport0: Printer, Hewlett-Packard HP LaserJet 1100 Feb 25 02:57:39 dell kernel: parport1: PC-style at 0x278, irq 5 [SPP,PS2,EPP] Feb 25 02:57:39 dell kernel: parport1: no IEEE-1284 device present. Feb 25 02:57:40 dell kernel: lp0: using parport0 (interrupt-driven). Feb 25 02:57:40 dell kernel: lp1: using parport1 (interrupt-driven).
--
Yup!
nano kernel: parport0: PC-style at 0x378, irq 7 [SPP,PS2,EPP] nano kernel: parport0: Printer, Hewlett-Packard HP LaserJet 6L
I setup everything as you describe below. I don't remember having to do all this stuff before(on other machines anyway). I guess I'm used to RH's fluffed-up stock kernels.
Thanks,
Mike
Quoted 45 lines · Tim Moore
Quoted 1 line
The parallel port is not being detected on my ABIT KT7A KT133 w/ Athlon
Also try comp.os.linux.hardware.
BIOS
----
278/irq5
378/irq7
EPP 1.9.config
-------CONFIG_PARPORT=yCONFIG_PARPORT_PC=yCONFIG_PNP=yCONFIG_PNP_PARPORT=yCONFIG_PRINTER=yCONFIG_PRINTER_READBACK=ykernal boot params
------------------
append="parport=0x378,7 parport=0x278,5"options for
/etc/rc.d/rc.local
------------------------------# abort on error, careful error check, trust IRQ. # see tunelp(8) & /usr/src/linux/drivers/misc/lp.c
/usr/sbin/tunelp/dev/lp0-a on -o on -T on/usr/sbin/tunelp/dev/lp1-a on -o on -T onlooks like this (lp1 was powered down at boot time)
Feb 25 02:57:39 dell kernel: parport0: PC-style at 0x378, irq 7 [SPP,PS2,EPP] Feb 25 02:57:39 dell kernel: parport0: Printer, Hewlett-Packard HP LaserJet 1100 Feb 25 02:57:39 dell kernel: parport1: PC-style at 0x278, irq 5 [SPP,PS2,EPP] Feb 25 02:57:39 dell kernel: parport1: no IEEE-1284 device present. Feb 25 02:57:40 dell kernel: lp0: using parport0 (interrupt-driven). Feb 25 02:57:40 dell kernel: lp1: using parport1 (interrupt-driven).--
Quoted 1 line · Michael B. Allen
The parallel port is not being detected on my ABIT KT7A KT133 w/ Athlon
Need dmesg output to see what parport is being told and what is finding out for itself.
Quoted 3 lines
BIOS options are:
728/IRQ5
^^^ 278, probably
Quoted 2 lines
378/IRQ7
3BC/IRQ7
But which one is it actually set to?
Quoted 1 line
Of the above what's optimal?
It depends what you're doing, really.
Quoted 3 lines
I also tried an options line in modules.conf. I believe it was:
options
parport_pcio=0x3bc irq=7
Take that out and see what happens.
Quoted 2 lines
That was reflected in /proc but no difference in actually "detecting" the parallel port.
I don't know what you mean really. Are you saying that you can't print, or just that the device ID probe (to get the printer name) isn't working?
Quoted 2 lines
Also, if I build parpart into the kernel I get nothing but a hard lockup on 'Starting kswapd v 1.5'.
That's quite strange.
Which kernel version are you using? Take a look at the 'troubleshooting' section of Documentation/parport.txt.
Tim.
*/
Quoted 3 lines · Michael B. Allen
I setup everything as you describe below. I don't remember having to do all this stuff before(on other machines anyway). I guess I'm used to RH's fluffed-up stock kernels.
Which stock kernel didn't work for you?
Tim.
*/