eepro100 question: why SCBCmd byte is 0x80?
I am trying to get netgear card working on a new (read as potentially buggy hardware) MIPS board.
The eepro100 driver basically works fine. It is just after a little while (usually 2 sec to 15 sec) network communication suddenly stops and I start see error message like "eepro100: wait_for_cmd_done timeout!".
I looked into this, and it appears that the SCBCmd byte in the command word has value 0x80 instead of the expected 0. I looked at the Intel manual, and it says nothing about the value being 0x80.
Does anybody have a clue here? I suspect some timing is wrong or a buggy PCI controller.
Please cc your reply to my email address. Thanks.
Jun
Which kernel are you using.
I've had a similar problem with 2.2.18.
I've backported 2.2.19pre changes to it.
(i.e. apply on 2.2.18 a diff of the file drivers/net/eepro100.c made between 2.2.18 and the last 2.2.19pre) And since I've never seen this problem again.
Christophe
Quoted 24 lines · On jeu, 22 mar 2001 22:04:45 Jun Sun wrote:
I am trying to get netgear card working on a new (read as potentially buggy hardware) MIPS board.
The eepro100 driver basically works fine. It is just after a little while (usually 2 sec to 15 sec) network communication suddenly stops and I start see error message like "eepro100:
wait_for_cmd_donetimeout!".I looked into this, and it appears that the SCBCmd byte in the command word has value
0x80instead of the expected 0. I looked at the Intel manual, and it says nothing about the value being0x80.Does anybody have a clue here? I suspect some timing is wrong or a buggy PCI controller.
Please cc your reply to my email address. Thanks.
Jun
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Signature · 8 lines
Christophe Barbé Software Engineer Lineo High Availability Group 42-46, rue Médéric 92110 Clichy - France phone (33).1.41.40.02.12 fax (33).1.41.40.02.01 www.lineo.com
Quoted 10 lines · christophe barbe
Which kernel are you using.
I've had a similar problem with 2.2.18.
I've backported 2.2.19pre changes to it.
(i.e. apply on 2.2.18 a diff of the filedrivers/net/eepro100.cmade between 2.2.18 and the last 2.2.19pre) And since I've never seen this problem again.Christophe
Kernel is 2.4.2. It is a MIPS machine.
I don't really think it is a driver problem, because the same dirver works fine on many other boards (including MIPS boards). In addition, I also tested with tulip cards and I had the same symptom. I am convinced it is a low-level problem (bus timing, PCI setting, buggy hardware, etc).
On the other hand, it could be a driver problem which is only exposed in this particular board, although very unlikely.
BTW, does the eepro100 patch for 2.2.19pre apply to 2.4.2? Or it is already in it?
Thanks.
Jun
Quoted 34 lines · On jeu, 22 mar 2001 22:04:45 Jun Sun wrote:
Quoted 15 lines
I am trying to get netgear card working on a new (read as potentially buggy hardware) MIPS board.
The eepro100 driver basically works fine. It is just after a little while (usually 2 sec to 15 sec) network communication suddenly stops and I start see error message like "eepro100:
wait_for_cmd_donetimeout!".I looked into this, and it appears that the SCBCmd byte in the command word has value
0x80instead of the expected 0. I looked at the Intel manual, and it says nothing about the value being0x80.Does anybody have a clue here? I suspect some timing is wrong or a buggy PCI controller.
Quoted 9 lines
Please cc your reply to my email address. Thanks.
Jun
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/--
Christophe Barbé
Software Engineer
Lineo High Availability Group
42-46, rue Médéric
92110 Clichy - France
phone (33).1.41.40.02.12
fax (33).1.41.40.02.01
www.lineo.com
Quoted 2 lines · Jun Sun
BTW, does the eepro100 patch for 2.2.19pre apply to 2.4.2? Or it is already in it?
It was backported from 2.4.1, so yes, it's already in.
Ion
Signature · 2 lines
It is better to keep your mouth shut and be thought a fool,
than to open it and remove all doubt.I'm having a similar problem with the onboard network card of a Sony Vaio Laptop. I haven't tracked it down as far as you can; how can I confirm its the same problem as yours?
Quoted 68 lines · Jun Sun
Quoted 10 lines · christophe barbe
Which kernel are you using.
I've had a similar problem with 2.2.18.
I've backported 2.2.19pre changes to it.
(i.e. apply on 2.2.18 a diff of the filedrivers/net/eepro100.cmade between 2.2.18 and the last 2.2.19pre) And since I've never seen this problem again.Christophe
Kernel is 2.4.2. It is a MIPS machine.
I don't really think it is a driver problem, because the same dirver works fine on many other boards (including MIPS boards). In addition, I also tested with tulip cards and I had the same symptom. I am convinced it is a low-level problem (bus timing, PCI setting, buggy hardware, etc).
On the other hand, it could be a driver problem which is only exposed in this particular board, although very unlikely.
BTW, does the eepro100 patch for 2.2.19pre apply to 2.4.2? Or it is already in it?
Thanks.
Jun
Quoted 25 lines · On jeu, 22 mar 2001 22:04:45 Jun Sun wrote:
Quoted 15 lines
I am trying to get netgear card working on a new (read as potentially buggy hardware) MIPS board.
The eepro100 driver basically works fine. It is just after a little while (usually 2 sec to 15 sec) network communication suddenly stops and I start see error message like "eepro100:
wait_for_cmd_donetimeout!".I looked into this, and it appears that the SCBCmd byte in the command word has value
0x80instead of the expected 0. I looked at the Intel manual, and it says nothing about the value being0x80.Does anybody have a clue here? I suspect some timing is wrong or a buggy PCI controller.
Quoted 9 lines
Please cc your reply to my email address. Thanks.
Jun
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/Quoted 9 lines
--
Christophe Barbé
Software Engineer
Lineo High Availability Group
42-46, rue Médéric
92110 Clichy - France
phone (33).1.41.40.02.12
fax (33).1.41.40.02.01
www.lineo.com-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Signature · 2 lines
-Steven Freedom is the freedom to say that two plus two equals four.