Skip to contentSkip to conversation

Matrox G400 Dualhead

DISCUSSION J Brook 3 participants 3 messages Mar 30, 2001 – Mar 31, 2001

lore
Share & tools
lore

J Brook

author
#0 lore raw
Quoted 4 lines

Does anyone know why fualhead is not working anymore? I just get a screen with rubbish on the second head. Also when kernel loads and and registers fb1 I lose signal on the second head.

...

Quoted 1 line

With 2.4.2 it was working just fine.

I have also noticed problems with the 2.4.3 release. I have a G450 32Mb, that I use in single-head mode. The console framebuffer runs fine at boot time, but when I load X (4.0.3 compiled with Matrox HAL library) and then return to the console, I get a blank screen (signal lost).

I don't know what the problem is. I can confirm with Mythos that under
2.4.2 it was working just fine :-)

Petr Vandrovec is the man who knows... what do you say Petr?!

John
----------------
[email protected]

#1 lore raw
Quoted 5 lines · J Brook
Quoted 5 lines

Does anyone know why fualhead is not working anymore? I just get a screen with rubbish on the second head. Also when kernel loads and and registers fb1 I lose signal on the second head.

On G400 there is no signal on second head after poweron. So you cannot lose it ;-) On G450 there is same signal on both heads - but you are talking about G400. Or no? They are very different (they have different everything except PCI device ID register :-( ). You should add 'Option "UseFBDev"' into your XF86Config-4 - probably together with 'Option "NoHWCursor"'.

Quoted 9 lines

...

Quoted 1 line

With 2.4.2 it was working just fine.

I have also noticed problems with the 2.4.3 release. I have a G450 32Mb, that I use in single-head mode. The console framebuffer runs fine at boot time, but when I load X (4.0.3 compiled with Matrox HAL library) and then return to the console, I get a blank screen (signal lost).

It is easy - do not do that. Matroxfb really does not expect that someone
will powerdown parts of chip which matroxfb needs, but which XFree does not use (for example clock source for secondary head) or that it will change
some undocumented registers (for example Matrox HAL driver changes memory
clock speed).

Quoted 3 lines

I don't know what the problem is. I can confirm with Mythos that under
2.4.2 it was working just fine :-)

I have no idea what changed between 2.4.2 and 2.4.3 - I do not remember that I was doing some changes into the matroxfb during last few weeks - so maybe that source of these problems is in XFree 4.0.3 ?
Petr Vandrovec [email protected]

#2 lore raw
In reply to J Brook
Quoted 8 lines · J Brook
Quoted 2 lines

With 2.4.2 it was working just fine.

I have also noticed problems with the 2.4.3 release. I have a G450 32Mb, that I use in single-head mode. The console framebuffer runs fine at boot time, but when I load X (4.0.3 compiled with Matrox HAL library) and then return to the console, I get a blank screen (signal lost).

In my case, when lilo boots my G450 on any video mode other than 'normal', going into X and then back into console, leads to a blank screen. I've observed this behavior in 2.2 and 2.4. Otherwise, I've no problem using the card in single or dual head.

Since the HAL lib is a binary, we might have to wait for Matrox to fix this problem.

Signature · 1 line
     Rafael