2.4.4 Kernel - ASUS CUV4X-DLS Question
I am encountering a problem I am having a little difficulty trying to solve. I have a system with a ASUS CUV4X-DLS system board, Bios 1004, 1GB of memory. dual P3 933MHz processors, a G450 Matrox card in the AGP slot, and a SBLive! sound card in PCI Slot 4.
I have provided the output from dmesg below and the .config file I used in compiling the 2.4.4 kernel on this system with a Redhat 7.1 (Seawolf) distribution.
The problem is that the system will boot everytime if and only if I use "noapic". If I do not use "noapic", the system will boot sometimes. The dmesg info below is from a successful boot when I did not use "noapic". When I do not use "noapic" __and__ it does not boot, the boot sequence stops at
..TIMER: vector=49 pin1=2 pin2=0
Matter of fact, the first boot after installing Redhat 7.1 stop at the same message/location with the 2.4.2 kernel.
I thought about "append"(ing) some "pirq" arguments to the boot but I really not sure how to do this and whether or not it would fix the problem.
What is the impact on performance by disabling APIC? Is there something wrong with the .config file that might fix this.
=================== Begin dmesg info ======================================
Linux version 2.4.4 (root@ouzel) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-81)) #2 SMP Wed May 2 17:19:43 MDT 2001 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fffc000 (usable)
BIOS-e820: 000000003fffc000 - 000000003ffff000 (ACPI data)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at 000f54c0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
On node 0 totalpages: 262140
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32764 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #3 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
SEP present.
MTRR present.
PGE present.
MCA present.
CMOV present.
PAT present.
PSE present.
MMX present.
FXSR present.
XMM present.
Bootup CPU
Processor #0 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
SEP present.
MTRR present.
PGE present.
MCA present.
CMOV present.
PAT present.
PSE present.
MMX present.
FXSR present.
XMM present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is ISA
I/O APIC #2 Version 17 at 0xFEC00000.
Int: type 3, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 00
Int: type 0, pol 0, trig 0, bus 2, IRQ 01, APIC ID 2, APIC INT 01
Int: type 0, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 02
Int: type 0, pol 0, trig 0, bus 2, IRQ 03, APIC ID 2, APIC INT 03
Int: type 0, pol 0, trig 0, bus 2, IRQ 04, APIC ID 2, APIC INT 04
Int: type 0, pol 0, trig 0, bus 2, IRQ 06, APIC ID 2, APIC INT 06
Int: type 0, pol 0, trig 0, bus 2, IRQ 07, APIC ID 2, APIC INT 07
Int: type 0, pol 0, trig 0, bus 2, IRQ 08, APIC ID 2, APIC INT 08
Int: type 0, pol 0, trig 0, bus 2, IRQ 0c, APIC ID 2, APIC INT 0c
Int: type 0, pol 0, trig 0, bus 2, IRQ 0e, APIC ID 2, APIC INT 0e
Int: type 0, pol 0, trig 0, bus 2, IRQ 0f, APIC ID 2, APIC INT 0f
Int: type 0, pol 3, trig 3, bus 1, IRQ 00, APIC ID 2, APIC INT 10
Int: type 0, pol 3, trig 3, bus 2, IRQ 00, APIC ID 2, APIC INT 00
Int: type 0, pol 3, trig 3, bus 0, IRQ 13, APIC ID 2, APIC INT 12
Int: type 0, pol 3, trig 3, bus 0, IRQ 1c, APIC ID 2, APIC INT 11
Int: type 0, pol 3, trig 3, bus 0, IRQ 20, APIC ID 2, APIC INT 13
Int: type 0, pol 3, trig 3, bus 0, IRQ 21, APIC ID 2, APIC INT 10
Int: type 0, pol 3, trig 3, bus 0, IRQ 28, APIC ID 2, APIC INT 12
Lint: type 3, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 00
Lint: type 1, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 01
Processors: 2
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
Kernel command line: auto BOOT_IMAGE=linux ro root=801 BOOT_FILE=/boot/vmlinuz-2.4.4
Initializing CPU#0
Detected 937.577 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1867.77 BogoMIPS
Memory: 1028188k/1048560k available (1353k kernel code, 19984k reserved, 560k data, 228k init, 131056k highmem) Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 06
per-CPU timeslice cutoff: 731.39 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting ID: 3000000
Getting ID: c000000
Getting LVT0: 8700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU present map: 9
Booting processor 1/0 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Initializing CPU#1
CPU#1 (phys ID: 0) waiting for CALLOUT
Startup point 1.
Waiting for send to finish...
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1874.32 BogoMIPS
Stack at about c211dfb8
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#1.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
OK.
CPU1: Intel Pentium III (Coppermine) stepping 06
CPU has booted.
Before bogomips.
Total of 2 processors activated (3742.10 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
Synchronizing Arb IDs.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-5, 2-9, 2-10, 2-11, 2-13, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=49 pin1=2 pin2=0
number of MP IRQ sources: 18.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178011
....... : max redirection entries: 0017
....... : IO APIC version: 0011
WARNING: unexpected IO-APIC, please mail
to [email protected]
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 0 1 1 1 1 1 1 31 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 000 00 1 0 0 0 0 0 0 00 06 003 03 0 0 0 0 0 1 1 51 07 003 03 0 0 0 0 0 1 1 59 08 003 03 0 0 0 0 0 1 1 61 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 003 03 0 0 0 0 0 1 1 69 0d 000 00 1 0 0 0 0 0 0 00 0e 003 03 0 0 0 0 0 1 1 71 0f 003 03 0 0 0 0 0 1 1 79 10 003 03 1 1 0 1 0 1 1 81 11 003 03 1 1 0 1 0 1 1 89 12 003 03 1 1 0 1 0 1 1 91 13 003 03 1 1 0 1 0 1 1 99 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0-> 2
IRQ1 -> 1
IRQ3 -> 3
IRQ4 -> 4
IRQ6 -> 6
IRQ7 -> 7
IRQ8 -> 8
IRQ12 -> 12
IRQ14 -> 14
IRQ15 -> 15
IRQ16 -> 16
IRQ17 -> 17
IRQ18 -> 18
IRQ19 -> 19
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 937.6805 MHz.
..... host bus clock speed is 133.9542 MHz.
cpu: 0, clocks: 1339542, slice: 446514 CPU0<T0:1339536,T1:893008,D:14,S:446514,C:1339542>
cpu: 1, clocks: 1339542, slice: 446514 CPU1<T0:1339536,T1:445552,D:956,S:446514,C:1339542>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at 0xf0d00, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Disabled enhanced CPU to PCI posting
PCI: Disabled enhanced CPU to PCI posting #2
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0PCI->APIC IRQ transform: (B0,I4,P3) -> 18PCI->APIC IRQ transform: (B0,I4,P3) -> 18PCI->APIC IRQ transform: (B0,I7,P0) -> 17PCI->APIC IRQ transform: (B0,I8,P0) -> 19PCI->APIC IRQ transform: (B0,I8,P1) -> 16PCI->APIC IRQ transform: (B0,I10,P0) -> 18PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
pty: 256 Unix98 ptys configured
block: queued sectors max/low 683440kB/552368kB, 2048 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller on PCI bus 00 dev 21VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs later
hda: RICOH CD-R/RW MP7120A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache
Uniform CD-ROM driver Revision: 3.12
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Loading I2O Core - (c) Copyright 1999 Red Hat Software
Linux I2O PCI support (c) 1999 Red Hat Software.
i2o: Checking for PCI I2O controllers...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
I2O Block Storage OSM v0.9
(c) Copyright 1999, 2000 Red Hat Software.
I2O LAN OSM (C) 1999 University of Helsinki.
loop: loaded (max 8 devices)
Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10d
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.htmleepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
eth0: Intel Corporation 82557 [Ethernet Pro 100], 00:E0:18:06:E3:F7, IRQ 17.
Board assembly 733470-006, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 32M @ 0xfc000000
[drm] AGP 0.99 on VIA Apollo Pro @ 0xfc000000 32MB
[drm] Initialized tdfx 1.0.0 20000928 on minor 63
[drm] AGP 0.99 on VIA Apollo Pro @ 0xfc000000 32MB
[drm] Initialized radeon 1.0.0 20010105 on minor 62
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 8, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-33 detected with Symbios NVRAM
sym53c8xx: at PCI bus 0, device 8, function 1
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-33 detected with Symbios NVRAM
sym53c1010-33-0: rev 0x1 on pci bus 0 device 8 function 0 irq 19
sym53c1010-33-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-33-0: on-chip RAM at 0xf6800000
sym53c1010-33-0: restart (scsi reset).
sym53c1010-33-0: handling phase mismatch from SCRIPTS.
sym53c1010-33-0: Downloading SCSI SCRIPTS.
sym53c1010-33-1: rev 0x1 on pci bus 0 device 8 function 1 irq 16
sym53c1010-33-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-33-1: on-chip RAM at 0xf5800000
sym53c1010-33-1: restart (scsi reset).
sym53c1010-33-1: handling phase mismatch from SCRIPTS.
sym53c1010-33-1: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx-1.7.3a-20010304
scsi1 : sym53c8xx-1.7.3a-20010304
Vendor: WDIGTL Model: WDE18310 ULTRA3 Rev: 1.30
Type: Direct-Access ANSI SCSI revision: 03
sym53c1010-33-0-<0,0>: tagged command queue depth set to 4
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
sym53c1010-33-0-<0,*>: FAST-80 WIDE SCSI 160.0 MB/s (12.5 ns, offset 62)
SCSI device sda: 35761710 512-byte hdwr sectors (18310 MB)
Partition check:
sda: sda1 sda2 sda3 sda4
Creative EMU10K1 PCI Audio Driver, version 0.7, 16:51:09 May 2 2001
emu10k1: EMU10K1 rev 8 model 0x8027 found, IO at 0xa800-0xa81f, IRQ 18usb.c: registered new driver hubuhci.c: USB UHCI at I/O 0xd400, IRQ 18usb.c: new USB bus registered, assigned bus number 1hub.c: USB hub foundhub.c: 2 ports detecteduhci.c: USB UHCI at I/O 0xd000, IRQ 18usb.c: new USB bus registered, assigned bus number 2hub.c: USB hub foundhub.c: 2 ports detected
Initializing USB Mass Storage driver...usb.c: registered new driver usb-storage
USB Mass Storage support registered.i2o_scsi.c: Version 0.0.1
chain_pool: 0 bytes @ f7cc5e00
(512 byte buffers X 4 can_queue X 0 i2o controllers)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 228k freed
Adding Swap: 2097136k swap-space (priority -1)
==================== Begin .config ============================ #
# Automatically generated make config: don't edit
#CONFIG_X86=yCONFIG_ISA=y
# CONFIG_SBUS is not setCONFIG_UID16=y
#
# Code maturity level options
#CONFIG_EXPERIMENTAL=y
#
# Loadable module support
#CONFIG_MODULES=yCONFIG_MODVERSIONS=yCONFIG_KMOD=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not setCONFIG_MPENTIUMIII=y
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not setCONFIG_X86_WP_WORKS_OK=yCONFIG_X86_INVLPG=yCONFIG_X86_CMPXCHG=yCONFIG_X86_XADD=yCONFIG_X86_BSWAP=yCONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not setCONFIG_RWSEM_XCHGADD_ALGORITHM=yCONFIG_X86_L1_CACHE_SHIFT=5CONFIG_X86_TSC=yCONFIG_X86_GOOD_APIC=yCONFIG_X86_PGE=yCONFIG_X86_USE_PPRO_CHECKSUM=y
# CONFIG_TOSHIBA is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
# CONFIG_NOHIGHMEM is not setCONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not setCONFIG_HIGHMEM=y
# CONFIG_MATH_EMULATION is not set
# CONFIG_MTRR is not setCONFIG_SMP=yCONFIG_HAVE_DEC_LOCK=y
#
# General setup
#CONFIG_NET=y
# CONFIG_VISWS is not setCONFIG_X86_IO_APIC=yCONFIG_X86_LOCAL_APIC=yCONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not setCONFIG_PCI_GOANY=yCONFIG_PCI_BIOS=yCONFIG_PCI_DIRECT=yCONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_HOTPLUG is not set
# CONFIG_PCMCIA is not setCONFIG_SYSVIPC=yCONFIG_BSD_PROCESS_ACCT=yCONFIG_SYSCTL=yCONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not setCONFIG_BINFMT_AOUT=yCONFIG_BINFMT_ELF=yCONFIG_BINFMT_MISC=y
# CONFIG_PM is not set
# CONFIG_ACPI is not set
# CONFIG_APM is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play configuration
#
# CONFIG_PNP is not set
# CONFIG_ISAPNP is not set
#
# Block devices
#CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not setCONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_NBD is not setCONFIG_BLK_DEV_RAM=yCONFIG_BLK_DEV_RAM_SIZE=4096CONFIG_BLK_DEV_INITRD=y
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_BLK_DEV_LVM is not set
#
# Networking options
#CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK is not set
# CONFIG_NETFILTER is not set
# CONFIG_FILTER is not setCONFIG_UNIX=yCONFIG_INET=yCONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_INET_ECN is not setCONFIG_SYN_COOKIES=y
# CONFIG_IPV6 is not set
# CONFIG_KHTTPD is not set
# CONFIG_ATM is not set
#
#
#
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_LLC is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
#
# ATA/IDE/MFM/RLL support
#CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives #
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
# CONFIG_BLK_DEV_IDEDISK is not set
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
# CONFIG_BLK_DEV_COMMERIAL is not set
# CONFIG_BLK_DEV_TIVO is not set
# CONFIG_BLK_DEV_IDECS is not set CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
#
# IDE chipset support/bugfixes
#CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not setCONFIG_BLK_DEV_RZ1000=yCONFIG_BLK_DEV_IDEPCI=yCONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_IDEDMA_PCI is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_IDEDMA_PCI_AUTO is not set
# CONFIG_BLK_DEV_IDEDMA is not set
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_AEC62XX_TUNING is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD7409 is not set
# CONFIG_AMD7409_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_PIIX_TUNING is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_OSB4 is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
# CONFIG_IDEDMA_AUTO is not set
# CONFIG_DMA_NONPCI is not setCONFIG_BLK_DEV_IDE_MODES=y
#
# SCSI support
#CONFIG_SCSI=y
#
# SCSI support type (disk, tape, CD-ROM)
#CONFIG_BLK_DEV_SD=yCONFIG_SD_EXTRA_DEVS=40
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs #CONFIG_SCSI_DEBUG_QUEUES=yCONFIG_SCSI_MULTI_LUN=yCONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not setCONFIG_SCSI_SYM53C8XX=yCONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=4CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32CONFIG_SCSI_NCR53C8XX_SYNC=20
# CONFIG_SCSI_NCR53C8XX_PROFILE is not set
# CONFIG_SCSI_NCR53C8XX_IOMAPPED is not set
# CONFIG_SCSI_NCR53C8XX_PQS_PDS is not set
# CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#CONFIG_I2O=yCONFIG_I2O_PCI=yCONFIG_I2O_BLOCK=yCONFIG_I2O_LAN=yCONFIG_I2O_SCSI=yCONFIG_I2O_PROC=y
#
# Network device support
#CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#CONFIG_NET_ETHERNET=y
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not setCONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_TULIP is not set
# CONFIG_DE4X5 is not set
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not setCONFIG_EEPRO100=y
# CONFIG_EEPRO100_PM is not set
# CONFIG_LNE390 is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139TOO is not set
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SK98LIN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Input core support
#
# CONFIG_INPUT is not set
#
# Character devices
#CONFIG_VT=yCONFIG_VT_CONSOLE=yCONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not setCONFIG_UNIX98_PTYS=yCONFIG_UNIX98_PTY_COUNT=256
#
# I2C support
#CONFIG_I2C=y
# CONFIG_I2C_ALGOBIT is not set
# CONFIG_I2C_ALGOPCF is not setCONFIG_I2C_CHARDEV=y
#
# Mice
#
# CONFIG_BUSMOUSE is not setCONFIG_MOUSE=yCONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
#
# Joysticks
#
# CONFIG_JOYSTICK is not set
#
# Input core support is needed for joysticks
#
# CONFIG_QIC02_TAPE is not set
#
# Watchdog Cards
#CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_WDT is not set
# CONFIG_WDTPCI is not set
# CONFIG_PCWATCHDOG is not set
# CONFIG_ACQUIRE_WDT is not set
# CONFIG_ADVANTECH_WDT is not set
# CONFIG_60XX_WDT is not set
# CONFIG_MIXCOMWD is not set
# CONFIG_I810_TCO is not set
# CONFIG_MACHZ_WDT is not set
# CONFIG_INTEL_RNG is not set
# CONFIG_NVRAM is not setCONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not setCONFIG_AGP=yCONFIG_AGP_INTEL=yCONFIG_AGP_I810=yCONFIG_AGP_VIA=yCONFIG_AGP_AMD=y
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not setCONFIG_DRM=yCONFIG_DRM_TDFX=y
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not setCONFIG_DRM_RADEON=y
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_MGA is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# File systems
#
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_REISERFS_CHECK is not set
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BFS_FS is not setCONFIG_FAT_FS=yCONFIG_MSDOS_FS=y
# CONFIG_UMSDOS_FS is not setCONFIG_VFAT_FS=y
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_CRAMFS is not setCONFIG_TMPFS=y
# CONFIG_RAMFS is not setCONFIG_ISO9660_FS=y
# CONFIG_JOLIET is not set
# CONFIG_MINIX_FS is not set
# CONFIG_NTFS_FS is not set
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not setCONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not setCONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not setCONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_SYSV_FS_WRITE is not set
# CONFIG_UDF_FS is not set
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not setCONFIG_NFS_FS=yCONFIG_NFS_V3=y
# CONFIG_ROOT_NFS is not set
# CONFIG_NFSD is not set
# CONFIG_NFSD_V3 is not setCONFIG_SUNRPC=yCONFIG_LOCKD=yCONFIG_LOCKD_V4=y
# CONFIG_SMB_FS is not set
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not setCONFIG_MSDOS_PARTITION=y
# CONFIG_SMB_NLS is not setCONFIG_NLS=y
#
# Native Language Support
#CONFIG_NLS_DEFAULT="iso8859-1"
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ISO8859_1 is not set
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Console drivers
#CONFIG_VGA_CONSOLE=y
# CONFIG_VIDEO_SELECT is not set
# CONFIG_MDA_CONSOLE is not set
#
# Frame-buffer support
#
# CONFIG_FB is not set
#
# Sound
#CONFIG_SOUND=y
# CONFIG_SOUND_CMPCI is not setCONFIG_SOUND_EMU10K1=y
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set
# CONFIG_SOUND_TVMIXER is not set
#
# USB support
#CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
# CONFIG_USB_DEVICEFS is not set
# CONFIG_USB_BANDWIDTH is not set
#
# USB Controllers
#CONFIG_USB_UHCI_ALT=y
# CONFIG_USB_OHCI is not set
#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH is not setCONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
#
# USB Human Interface Devices (HID)
#
#
# Input core support is needed for USB HID
#
#
# USB Imaging devices
#
# CONFIG_USB_DC2XX is not set
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
#
# USB Multimedia devices
#
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_DABUSB is not set
#
# USB Network adaptors
#
# CONFIG_USB_PLUSB is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_NET1080 is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB misc drivers
#
# CONFIG_USB_RIO500 is not set
#
# Kernel hacking
#
# CONFIG_MAGIC_SYSRQ is not set
Signature · 7 lines
++++++++++++++++++++++++++++++++++++++++++++++ Dave Neal, Center for Nonlinear Studies Phone w/ Voice Mail (505) 665-6471 Digital Pager - (505) 664-8666 Wirth's Law: Software gets slower faster than Hardware gets faster! ++++++++++++++++++++++++++++++++++++++++++++++
Quoted 4 lines
trying to solve. I have a system with a ASUS CUV4X-DLS system
The problem is that the system will boot everytime if and only if I use "noapic". If I do not use "noapic", the system will
Known problem with the CUV4X boards.
Quoted 2 lines
What is the impact on performance by disabling APIC? Is there something wrong with the .config file that might fix this.
Disabling the apic stops irq sharing from occuring. The impact is normally pretty minimal
I just wanted to throw in my two cents and say that there appear to be widespread issues with the APIC code in 2.4.x. I'm tempted to stick my neck out and say that it might be best to disable SMP IOAPIC by default until APIC can be massaged, at least for a wider variety of hardware.
I'm getting many replies to my "Persistent 2.4.x stability problem" post. Manfred Spraul has been extremely helpful in working through the issue with me and providing the "noapic" work-around, but this problem is fairly subtle and is most likely effecting a lot more people than those reporting the issue.
It seems like some Tyan motherboards and _all_ HP hardware do not play well with the APIC code. That's a pretty big subset of hardware; Asus also seems to be effected now, and many other platforms may also suffer from APICitis. I realize there are different failure modes and I assume different issues are involved within the APIC code.
I have HP hardware that I can make available for patches and tests -- I want to help solve this and contribute what I can. Using "noapic" does take the pressure off the issue, but I guess this problem remains insidious in my mind. I realize I'm not fully familiar with the general issues, so I apologize if I'm re-covering old ground or missing any relevant issues.
Thanks,
--
Ken.
Quoted 1,186 lines · David A. Neal
I am encountering a problem I am having a little difficulty trying to solve. I have a system with a ASUS CUV4X-DLS system board, Bios 1004, 1GB of memory. dual P3 933MHz processors, a G450 Matrox card in the AGP slot, and a SBLive! sound card in PCI Slot 4.
I have provided the output from dmesg below and the .config file I used in compiling the 2.4.4 kernel on this system with a Redhat 7.1 (Seawolf) distribution.
The problem is that the system will boot everytime if and only if I use "noapic". If I do not use "noapic", the system will boot sometimes. The dmesg info below is from a successful boot when I did not use "noapic". When I do not use "noapic"
__and__it does not boot, the boot sequence stops at..TIMER: vector=49 pin1=2 pin2=0Matter of fact, the first boot after installing Redhat 7.1 stop at the same message/location with the 2.4.2 kernel.
I thought about "append"(ing) some "pirq" arguments to the boot but I really not sure how to do this and whether or not it would fix the problem.
What is the impact on performance by disabling APIC? Is there something wrong with the .config file that might fix this.
=================== Begin dmesg info ======================================
Linux version 2.4.4 (root@ouzel) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-81)) #2 SMP Wed May 2 17:19:43 MDT 2001 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 -000000000009f000(usable)
BIOS-e820:000000000009f000-00000000000a0000(reserved)
BIOS-e820:00000000000f0000- 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 -000000003fffc000(usable)
BIOS-e820:000000003fffc000-000000003ffff000(ACPI data)
BIOS-e820:000000003ffff000- 0000000040000000 (ACPI NVS)
BIOS-e820:00000000fec00000-00000000fec01000(reserved)
BIOS-e820:00000000fee00000-00000000fee01000(reserved)
BIOS-e820:00000000ffff0000- 0000000100000000 (reserved)
127MB HIGHMEM available.
Scan SMP fromc0000000for 1024 bytes.
Scan SMP fromc009fc00for 1024 bytes.
Scan SMP fromc00f0000for 65536 bytes.
found SMP MP-table at000f54c0
hm, page000f5000reserved twice.
hm, page000f6000reserved twice.
hm, page000f5000reserved twice.
hm, page000f6000reserved twice.
On node 0 totalpages: 262140
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32764 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at:0xFEE00000
Processor #3 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
SEP present.
MTRR present.
PGE present.
MCA present.
CMOV present.
PAT present.
PSE present.
MMX present.
FXSR present.
XMM present.
Bootup CPU
Processor #0 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
SEP present.
MTRR present.
PGE present.
MCA present.
CMOV present.
PAT present.
PSE present.
MMX present.
FXSR present.
XMM present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is ISA
I/O APIC #2 Version 17 at0xFEC00000.
Int: type 3, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 00
Int: type 0, pol 0, trig 0, bus 2, IRQ 01, APIC ID 2, APIC INT 01
Int: type 0, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 02
Int: type 0, pol 0, trig 0, bus 2, IRQ 03, APIC ID 2, APIC INT 03
Int: type 0, pol 0, trig 0, bus 2, IRQ 04, APIC ID 2, APIC INT 04
Int: type 0, pol 0, trig 0, bus 2, IRQ 06, APIC ID 2, APIC INT 06
Int: type 0, pol 0, trig 0, bus 2, IRQ 07, APIC ID 2, APIC INT 07
Int: type 0, pol 0, trig 0, bus 2, IRQ 08, APIC ID 2, APIC INT 08
Int: type 0, pol 0, trig 0, bus 2, IRQ 0c, APIC ID 2, APIC INT 0c
Int: type 0, pol 0, trig 0, bus 2, IRQ 0e, APIC ID 2, APIC INT 0e
Int: type 0, pol 0, trig 0, bus 2, IRQ 0f, APIC ID 2, APIC INT 0f
Int: type 0, pol 3, trig 3, bus 1, IRQ 00, APIC ID 2, APIC INT 10
Int: type 0, pol 3, trig 3, bus 2, IRQ 00, APIC ID 2, APIC INT 00
Int: type 0, pol 3, trig 3, bus 0, IRQ 13, APIC ID 2, APIC INT 12
Int: type 0, pol 3, trig 3, bus 0, IRQ 1c, APIC ID 2, APIC INT 11
Int: type 0, pol 3, trig 3, bus 0, IRQ 20, APIC ID 2, APIC INT 13
Int: type 0, pol 3, trig 3, bus 0, IRQ 21, APIC ID 2, APIC INT 10
Int: type 0, pol 3, trig 3, bus 0, IRQ 28, APIC ID 2, APIC INT 12
Lint: type 3, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 00
Lint: type 1, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 01
Processors: 2
mapped APIC toffffe000(fee00000)
mapped IOAPIC toffffd000(fec00000)
Kernel command line: auto BOOT_IMAGE=linux ro root=801 BOOT_FILE=/boot/vmlinuz-2.4.4
Initializing CPU#0
Detected 937.577 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1867.77 BogoMIPS
Memory: 1028188k/1048560k available (1353k kernel code, 19984k reserved, 560k data, 228k init, 131056k highmem) Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
CPU: Before vendor init, caps:0383fbff00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps:0383fbff00000000 00000000 00000000
CPU: After generic, caps:0383fbff00000000 00000000 00000000
CPU: Common caps:0383fbff00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: Before vendor init, caps:0383fbff00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps:0383fbff00000000 00000000 00000000
CPU: After generic, caps:0383fbff00000000 00000000 00000000
CPU: Common caps:0383fbff00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 06
per-CPU timeslice cutoff: 731.39 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting ID: 3000000
Getting ID: c000000
Getting LVT0: 8700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU present map: 9
Booting processor 1/0 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
Afterapic_write.
Initializing CPU#1
CPU#1 (phys ID: 0) waiting for CALLOUT
Startup point 1.
Waiting for send to finish...
+Sending STARTUP #2.
Afterapic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, beforesetup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1874.32 BogoMIPS
Stack at aboutc211dfb8
CPU: Before vendor init, caps:0383fbff00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#1.
CPU: After vendor init, caps:0383fbff00000000 00000000 00000000
CPU: After generic, caps:0383fbff00000000 00000000 00000000
CPU: Common caps:0383fbff00000000 00000000 00000000
OK.
CPU1: Intel Pentium III (Coppermine) stepping 06
CPU has booted.
Before bogomips.
Total of 2 processors activated (3742.10 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
Synchronizing Arb IDs.
initIO_APICIRQs
IO-APIC (apicid-pin) 2-5, 2-9, 2-10, 2-11, 2-13, 2-20, 2-21, 2-22,
2-23 not connected.
..TIMER: vector=49 pin1=2 pin2=0
number of MP IRQ sources: 18.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178011
....... : max redirection entries: 0017
....... : IO APIC version: 0011
WARNING: unexpected IO-APIC, please mail
to [email protected]
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:00 003 03 0 1 1 1 1 1 1 31 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 000 00 1 0 0 0 0 0 0 00 06 003 03 0 0 0 0 0 1 1 51 07 003 03 0 0 0 0 0 1 1 59 08 003 03 0 0 0 0 0 1 1 61 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 003 03 0 0 0 0 0 1 1 69 0d 000 00 1 0 0 0 0 0 0 00 0e 003 03 0 0 0 0 0 1 1 71 0f 003 03 0 0 0 0 0 1 1 79 10 003 03 1 1 0 1 0 1 1 81 11 003 03 1 1 0 1 0 1 1 89 12 003 03 1 1 0 1 0 1 1 91 13 003 03 1 1 0 1 0 1 1 99 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00IRQ to pin mappings:
IRQ0 -> 0-> 2
IRQ1 -> 1
IRQ3 -> 3
IRQ4 -> 4
IRQ6 -> 6
IRQ7 -> 7
IRQ8 -> 8
IRQ12 -> 12
IRQ14 -> 14
IRQ15 -> 15
IRQ16 -> 16
IRQ17 -> 17
IRQ18 -> 18
IRQ19 -> 19
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 937.6805 MHz.
..... host bus clock speed is 133.9542 MHz.
cpu: 0, clocks: 1339542, slice: 446514 CPU0<T0:1339536,T1:893008,D:14,S:446514,C:1339542>
cpu: 1, clocks: 1339542, slice: 446514 CPU1<T0:1339536,T1:445552,D:956,S:446514,C:1339542>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at0xf0d00, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Disabled enhanced CPU to PCI posting
PCI: Disabled enhanced CPU to PCI posting #2
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0PCI->APICIRQ transform: (B0,I4,P3) -> 18PCI->APICIRQ transform: (B0,I4,P3) -> 18PCI->APICIRQ transform: (B0,I7,P0) -> 17PCI->APICIRQ transform: (B0,I8,P0) -> 19PCI->APICIRQ transform: (B0,I8,P1) -> 16PCI->APICIRQ transform: (B0,I10,P0) -> 18PCI->APICIRQ transform: (B1,I0,P0) -> 16
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
pty: 256 Unix98 ptys configured
block: queued sectors max/low 683440kB/552368kB, 2048 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller on PCI bus 00 dev 21VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs later
hda: RICOH CD-R/RW MP7120A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache
Uniform CD-ROM driver Revision: 3.12
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Loading I2O Core - (c) Copyright 1999 Red Hat Software
Linux I2O PCI support (c) 1999 Red Hat Software.
i2o: Checking for PCI I2O controllers...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
I2O Block Storage OSM v0.9
(c) Copyright 1999, 2000 Red Hat Software.
I2O LAN OSM (C) 1999 University of Helsinki.
loop: loaded (max 8 devices)
Serial driver version 5.05a (2001-03-20) withMANY_PORTSSHARE_IRQSERIAL_PCIenabled ttyS00 at0x03f8(irq = 4) is a 16550A
ttyS01 at0x02f8(irq = 3) is a 16550A
Real Time Clock Driver v1.10d
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.htmleepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
eth0: Intel Corporation 82557 [Ethernet Pro 100], 00:E0:18:06:E3:F7, IRQ 17.
Board assembly 733470-006, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 32M @0xfc000000
[drm] AGP 0.99 on VIA Apollo Pro @0xfc00000032MB
[drm] Initialized tdfx 1.0.0 20000928 on minor 63
[drm] AGP 0.99 on VIA Apollo Pro @0xfc00000032MB
[drm] Initialized radeon 1.0.0 20010105 on minor 62
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 8, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-33 detected with Symbios NVRAM
sym53c8xx: at PCI bus 0, device 8, function 1
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-33 detected with Symbios NVRAM
sym53c1010-33-0: rev0x1on pci bus 0 device 8 function 0 irq 19
sym53c1010-33-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-33-0: on-chip RAM at0xf6800000
sym53c1010-33-0: restart (scsi reset).
sym53c1010-33-0: handling phase mismatch from SCRIPTS.
sym53c1010-33-0: Downloading SCSI SCRIPTS.
sym53c1010-33-1: rev0x1on pci bus 0 device 8 function 1 irq 16
sym53c1010-33-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-33-1: on-chip RAM at0xf5800000
sym53c1010-33-1: restart (scsi reset).
sym53c1010-33-1: handling phase mismatch from SCRIPTS.
sym53c1010-33-1: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx-1.7.3a-20010304
scsi1 : sym53c8xx-1.7.3a-20010304
Vendor: WDIGTL Model: WDE18310 ULTRA3 Rev: 1.30
Type: Direct-Access ANSI SCSI revision: 03
sym53c1010-33-0-<0,0>: tagged command queue depth set to 4
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
sym53c1010-33-0-<0,*>: FAST-80 WIDE SCSI 160.0 MB/s (12.5 ns, offset 62)
SCSI device sda: 35761710 512-byte hdwr sectors (18310 MB)
Partition check:
sda: sda1 sda2 sda3 sda4
Creative EMU10K1 PCI Audio Driver, version 0.7, 16:51:09 May 2 2001
emu10k1: EMU10K1 rev 8 model0x8027found, IO at 0xa800-0xa81f, IRQ 18usb.c: registered new driver hubuhci.c: USB UHCI at I/O0xd400, IRQ 18usb.c: new USB bus registered, assigned bus number 1hub.c: USB hub foundhub.c: 2 ports detecteduhci.c: USB UHCI at I/O0xd000, IRQ 18usb.c: new USB bus registered, assigned bus number 2hub.c: USB hub foundhub.c: 2 ports detected
Initializing USB Mass Storage driver...usb.c: registered new driver usb-storage
USB Mass Storage support registered.i2o_scsi.c: Version 0.0.1
chain_pool: 0 bytes @f7cc5e00
(512 byte buffers X 4can_queueX 0 i2o controllers)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 228k freed
Adding Swap: 2097136k swap-space (priority -1)==================== Begin .config ============================ #
# Automatically generated make config: don't edit
#CONFIG_X86=yCONFIG_ISA=y
#CONFIG_SBUSis not setCONFIG_UID16=y#
# Code maturity level options
#CONFIG_EXPERIMENTAL=y#
# Loadable module support
#CONFIG_MODULES=yCONFIG_MODVERSIONS=yCONFIG_KMOD=y#
# Processor type and features
#
#CONFIG_M386is not set
#CONFIG_M486is not set
#CONFIG_M586is not set
#CONFIG_M586TSCis not set
#CONFIG_M586MMXis not set
#CONFIG_M686is not setCONFIG_MPENTIUMIII=y
#CONFIG_MPENTIUM4is not set
#CONFIG_MK6is not set
#CONFIG_MK7is not set
#CONFIG_MCRUSOEis not set
#CONFIG_MWINCHIPC6is not set
#CONFIG_MWINCHIP2is not set
#CONFIG_MWINCHIP3Dis not set
#CONFIG_MCYRIXIIIis not setCONFIG_X86_WP_WORKS_OK=yCONFIG_X86_INVLPG=yCONFIG_X86_CMPXCHG=yCONFIG_X86_XADD=yCONFIG_X86_BSWAP=yCONFIG_X86_POPAD_OK=y
#CONFIG_RWSEM_GENERIC_SPINLOCKis not setCONFIG_RWSEM_XCHGADD_ALGORITHM=yCONFIG_X86_L1_CACHE_SHIFT=5CONFIG_X86_TSC=yCONFIG_X86_GOOD_APIC=yCONFIG_X86_PGE=yCONFIG_X86_USE_PPRO_CHECKSUM=y
#CONFIG_TOSHIBAis not set
#CONFIG_MICROCODEis not set
#CONFIG_X86_MSRis not set
#CONFIG_X86_CPUIDis not set
#CONFIG_NOHIGHMEMis not setCONFIG_HIGHMEM4G=y
#CONFIG_HIGHMEM64Gis not setCONFIG_HIGHMEM=y
#CONFIG_MATH_EMULATIONis not set
#CONFIG_MTRRis not setCONFIG_SMP=yCONFIG_HAVE_DEC_LOCK=y#
# General setup
#CONFIG_NET=y
#CONFIG_VISWSis not setCONFIG_X86_IO_APIC=yCONFIG_X86_LOCAL_APIC=yCONFIG_PCI=y
#CONFIG_PCI_GOBIOSis not set
#CONFIG_PCI_GODIRECTis not setCONFIG_PCI_GOANY=yCONFIG_PCI_BIOS=yCONFIG_PCI_DIRECT=yCONFIG_PCI_NAMES=y
#CONFIG_EISAis not set
#CONFIG_MCAis not set
#CONFIG_HOTPLUGis not set
#CONFIG_PCMCIAis not setCONFIG_SYSVIPC=yCONFIG_BSD_PROCESS_ACCT=yCONFIG_SYSCTL=yCONFIG_KCORE_ELF=y
#CONFIG_KCORE_AOUTis not setCONFIG_BINFMT_AOUT=yCONFIG_BINFMT_ELF=yCONFIG_BINFMT_MISC=y
#CONFIG_PMis not set
#CONFIG_ACPIis not set
#CONFIG_APMis not set#
# Memory Technology Devices (MTD)
#
#CONFIG_MTDis not set#
# Parallel port support
#
#CONFIG_PARPORTis not set#
# Plug and Play configuration
#
#CONFIG_PNPis not set
#CONFIG_ISAPNPis not set#
# Block devices
#CONFIG_BLK_DEV_FD=y
#CONFIG_BLK_DEV_XDis not set
#CONFIG_PARIDEis not set
#CONFIG_BLK_CPQ_DAis not set
#CONFIG_BLK_CPQ_CISS_DAis not set
#CONFIG_BLK_DEV_DAC960is not setCONFIG_BLK_DEV_LOOP=y
#CONFIG_BLK_DEV_NBDis not setCONFIG_BLK_DEV_RAM=yCONFIG_BLK_DEV_RAM_SIZE=4096CONFIG_BLK_DEV_INITRD=y#
# Multi-device support (RAID and LVM)
#
#CONFIG_MDis not set
#CONFIG_BLK_DEV_MDis not set
#CONFIG_MD_LINEARis not set
#CONFIG_MD_RAID0is not set
#CONFIG_MD_RAID1is not set
#CONFIG_MD_RAID5is not set
#CONFIG_BLK_DEV_LVMis not set#
# Networking options
#CONFIG_PACKET=y
#CONFIG_PACKET_MMAPis not set
#CONFIG_NETLINKis not set
#CONFIG_NETFILTERis not set
#CONFIG_FILTERis not setCONFIG_UNIX=yCONFIG_INET=yCONFIG_IP_MULTICAST=y
#CONFIG_IP_ADVANCED_ROUTERis not set
#CONFIG_IP_PNPis not set
#CONFIG_NET_IPIPis not set
#CONFIG_NET_IPGREis not set
#CONFIG_IP_MROUTEis not set
#CONFIG_INET_ECNis not setCONFIG_SYN_COOKIES=y
#CONFIG_IPV6is not set
#CONFIG_KHTTPDis not set
#CONFIG_ATMis not set#
#
#
#CONFIG_IPXis not set
#CONFIG_ATALKis not set
#CONFIG_DECNETis not set
#CONFIG_BRIDGEis not set
#CONFIG_X25is not set
#CONFIG_LAPBis not set
#CONFIG_LLCis not set
#CONFIG_NET_DIVERTis not set
#CONFIG_ECONETis not set
#CONFIG_WAN_ROUTERis not set
#CONFIG_NET_FASTROUTEis not set
#CONFIG_NET_HW_FLOWCONTROLis not set#
# QoS and/or fair queueing
#
#CONFIG_NET_SCHEDis not set#
# Telephony Support
#
#CONFIG_PHONEis not set
#CONFIG_PHONE_IXJis not set#
# ATA/IDE/MFM/RLL support
#CONFIG_IDE=y#
# IDE, ATA and ATAPI Block devices
#CONFIG_BLK_DEV_IDE=y#
# Please seeDocumentation/ide.txtfor help/info on IDE drives #
#CONFIG_BLK_DEV_HD_IDEis not set
#CONFIG_BLK_DEV_HDis not set
#CONFIG_BLK_DEV_IDEDISKis not set
#CONFIG_IDEDISK_MULTI_MODEis not set
#CONFIG_BLK_DEV_IDEDISK_VENDORis not set
#CONFIG_BLK_DEV_IDEDISK_FUJITSUis not set
#CONFIG_BLK_DEV_IDEDISK_IBMis not set
#CONFIG_BLK_DEV_IDEDISK_MAXTORis not set
#CONFIG_BLK_DEV_IDEDISK_QUANTUMis not set
#CONFIG_BLK_DEV_IDEDISK_SEAGATEis not set
#CONFIG_BLK_DEV_IDEDISK_WDis not set
#CONFIG_BLK_DEV_COMMERIALis not set
#CONFIG_BLK_DEV_TIVOis not set
#CONFIG_BLK_DEV_IDECSis not setCONFIG_BLK_DEV_IDECD=y
#CONFIG_BLK_DEV_IDETAPEis not set
#CONFIG_BLK_DEV_IDEFLOPPYis not set
#CONFIG_BLK_DEV_IDESCSIis not set#
# IDE chipset support/bugfixes
#CONFIG_BLK_DEV_CMD640=y
#CONFIG_BLK_DEV_CMD640_ENHANCEDis not set
#CONFIG_BLK_DEV_ISAPNPis not setCONFIG_BLK_DEV_RZ1000=yCONFIG_BLK_DEV_IDEPCI=yCONFIG_IDEPCI_SHARE_IRQ=y
#CONFIG_BLK_DEV_IDEDMA_PCIis not set
#CONFIG_BLK_DEV_OFFBOARDis not set
#CONFIG_IDEDMA_PCI_AUTOis not set
#CONFIG_BLK_DEV_IDEDMAis not set
#CONFIG_IDEDMA_PCI_WIPis not set
#CONFIG_IDEDMA_NEW_DRIVE_LISTINGSis not set
#CONFIG_BLK_DEV_AEC62XXis not set
#CONFIG_AEC62XX_TUNINGis not set
#CONFIG_BLK_DEV_ALI15X3is not set
#CONFIG_WDC_ALI15X3is not set
#CONFIG_BLK_DEV_AMD7409is not set
#CONFIG_AMD7409_OVERRIDEis not set
#CONFIG_BLK_DEV_CMD64Xis not set
#CONFIG_BLK_DEV_CY82C693is not set
#CONFIG_BLK_DEV_CS5530is not set
#CONFIG_BLK_DEV_HPT34Xis not set
#CONFIG_HPT34X_AUTODMAis not set
#CONFIG_BLK_DEV_HPT366is not set
#CONFIG_BLK_DEV_PIIXis not set
#CONFIG_PIIX_TUNINGis not set
#CONFIG_BLK_DEV_NS87415is not set
#CONFIG_BLK_DEV_OPTI621is not set
#CONFIG_BLK_DEV_PDC202XXis not set
#CONFIG_PDC202XX_BURSTis not set
#CONFIG_BLK_DEV_OSB4is not set
#CONFIG_BLK_DEV_SIS5513is not set
#CONFIG_BLK_DEV_SLC90E66is not set
#CONFIG_BLK_DEV_TRM290is not set
#CONFIG_BLK_DEV_VIA82CXXXis not set
#CONFIG_IDE_CHIPSETSis not set
#CONFIG_IDEDMA_AUTOis not set
#CONFIG_DMA_NONPCIis not setCONFIG_BLK_DEV_IDE_MODES=y#
# SCSI support
#CONFIG_SCSI=y#
# SCSI support type (disk, tape, CD-ROM)
#CONFIG_BLK_DEV_SD=yCONFIG_SD_EXTRA_DEVS=40
#CONFIG_CHR_DEV_STis not set
#CONFIG_CHR_DEV_OSSTis not set
#CONFIG_BLK_DEV_SRis not set
#CONFIG_CHR_DEV_SGis not set#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs #CONFIG_SCSI_DEBUG_QUEUES=yCONFIG_SCSI_MULTI_LUN=yCONFIG_SCSI_CONSTANTS=y
#CONFIG_SCSI_LOGGINGis not set#
# SCSI low-level drivers
#
#CONFIG_BLK_DEV_3W_XXXX_RAIDis not set
#CONFIG_SCSI_7000FASSTis not set
#CONFIG_SCSI_ACARDis not set
#CONFIG_SCSI_AHA152Xis not set
#CONFIG_SCSI_AHA1542is not set
#CONFIG_SCSI_AHA1740is not set
#CONFIG_SCSI_AIC7XXXis not set
#CONFIG_SCSI_AIC7XXX_OLDis not set
#CONFIG_SCSI_ADVANSYSis not set
#CONFIG_SCSI_IN2000is not set
#CONFIG_SCSI_AM53C974is not set
#CONFIG_SCSI_MEGARAIDis not set
#CONFIG_SCSI_BUSLOGICis not set
#CONFIG_SCSI_CPQFCTSis not set
#CONFIG_SCSI_DMX3191Dis not set
#CONFIG_SCSI_DTC3280is not set
#CONFIG_SCSI_EATAis not set
#CONFIG_SCSI_EATA_DMAis not set
#CONFIG_SCSI_EATA_PIOis not set
#CONFIG_SCSI_FUTURE_DOMAINis not set
#CONFIG_SCSI_GDTHis not set
#CONFIG_SCSI_GENERIC_NCR5380is not set
#CONFIG_SCSI_IPSis not set
#CONFIG_SCSI_INITIOis not set
#CONFIG_SCSI_INIA100is not set
#CONFIG_SCSI_NCR53C406Ais not set
#CONFIG_SCSI_NCR53C7xxis not set
#CONFIG_SCSI_NCR53C8XXis not setCONFIG_SCSI_SYM53C8XX=yCONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=4CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32CONFIG_SCSI_NCR53C8XX_SYNC=20
#CONFIG_SCSI_NCR53C8XX_PROFILEis not set
#CONFIG_SCSI_NCR53C8XX_IOMAPPEDis not set
#CONFIG_SCSI_NCR53C8XX_PQS_PDSis not set
#CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPATis not set
#CONFIG_SCSI_PAS16is not set
#CONFIG_SCSI_PCI2000is not set
#CONFIG_SCSI_PCI2220Iis not set
#CONFIG_SCSI_PSI240Iis not set
#CONFIG_SCSI_QLOGIC_FASis not set
#CONFIG_SCSI_QLOGIC_ISPis not set
#CONFIG_SCSI_QLOGIC_FCis not set
#CONFIG_SCSI_QLOGIC_1280is not set
#CONFIG_SCSI_SEAGATEis not set
#CONFIG_SCSI_SIM710is not set
#CONFIG_SCSI_SYM53C416is not set
#CONFIG_SCSI_DC390Tis not set
#CONFIG_SCSI_T128is not set
#CONFIG_SCSI_U14_34Fis not set
#CONFIG_SCSI_ULTRASTORis not set
#CONFIG_SCSI_DEBUGis not set#
# IEEE 1394 (FireWire) support
#
#CONFIG_IEEE1394is not set#
# I2O device support
#CONFIG_I2O=yCONFIG_I2O_PCI=yCONFIG_I2O_BLOCK=yCONFIG_I2O_LAN=yCONFIG_I2O_SCSI=yCONFIG_I2O_PROC=y#
# Network device support
#CONFIG_NETDEVICES=y#
# ARCnet devices
#
#CONFIG_ARCNETis not set
#CONFIG_DUMMYis not set
#CONFIG_BONDINGis not set
#CONFIG_EQUALIZERis not set
#CONFIG_TUNis not set
#CONFIG_NET_SB1000is not set#
# Ethernet (10 or 100Mbit)
#CONFIG_NET_ETHERNET=y
#CONFIG_NET_VENDOR_3COMis not set
#CONFIG_LANCEis not set
#CONFIG_NET_VENDOR_SMCis not set
#CONFIG_NET_VENDOR_RACALis not set
#CONFIG_AT1700is not set
#CONFIG_DEPCAis not set
#CONFIG_HP100is not set
#CONFIG_NET_ISAis not setCONFIG_NET_PCI=y
#CONFIG_PCNET32is not set
#CONFIG_ADAPTEC_STARFIREis not set
#CONFIG_AC3200is not set
#CONFIG_APRICOTis not set
#CONFIG_CS89x0is not set
#CONFIG_TULIPis not set
#CONFIG_DE4X5is not set
#CONFIG_DGRSis not set
#CONFIG_DM9102is not setCONFIG_EEPRO100=y
#CONFIG_EEPRO100_PMis not set
#CONFIG_LNE390is not set
#CONFIG_NATSEMIis not set
#CONFIG_NE2K_PCIis not set
#CONFIG_NE3210is not set
#CONFIG_ES3210is not set
#CONFIG_8139TOOis not set
#CONFIG_8139TOO_PIOis not set
#CONFIG_8139TOO_TUNE_TWISTERis not set
#CONFIG_8139TOO_8129is not set
#CONFIG_SIS900is not set
#CONFIG_EPIC100is not set
#CONFIG_SUNDANCEis not set
#CONFIG_TLANis not set
#CONFIG_VIA_RHINEis not set
#CONFIG_WINBOND_840is not set
#CONFIG_HAPPYMEALis not set
#CONFIG_NET_POCKETis not set#
# Ethernet (1000 Mbit)
#
#CONFIG_ACENICis not set
#CONFIG_HAMACHIis not set
#CONFIG_YELLOWFINis not set
#CONFIG_SK98LINis not set
#CONFIG_FDDIis not set
#CONFIG_HIPPIis not set
#CONFIG_PPPis not set
#CONFIG_SLIPis not set#
# Wireless LAN (non-hamradio)
#
#CONFIG_NET_RADIOis not set#
# Token Ring devices
#
#CONFIG_TRis not set
#CONFIG_NET_FCis not set
#CONFIG_RCPCIis not set
#CONFIG_SHAPERis not set#
# Wan interfaces
#
#CONFIG_WANis not set#
# Amateur Radio support
#
#CONFIG_HAMRADIOis not set#
# IrDA (infrared) support
#
#CONFIG_IRDAis not set#
# ISDN subsystem
#
#CONFIG_ISDNis not set#
# Old CD-ROM drivers (not SCSI, not IDE)
#
#CONFIG_CD_NO_IDESCSIis not set#
# Input core support
#
#CONFIG_INPUTis not set#
# Character devices
#CONFIG_VT=yCONFIG_VT_CONSOLE=yCONFIG_SERIAL=y
#CONFIG_SERIAL_CONSOLEis not set
#CONFIG_SERIAL_EXTENDEDis not set
#CONFIG_SERIAL_NONSTANDARDis not setCONFIG_UNIX98_PTYS=yCONFIG_UNIX98_PTY_COUNT=256#
# I2C support
#CONFIG_I2C=y
#CONFIG_I2C_ALGOBITis not set
#CONFIG_I2C_ALGOPCFis not setCONFIG_I2C_CHARDEV=y#
# Mice
#
#CONFIG_BUSMOUSEis not setCONFIG_MOUSE=yCONFIG_PSMOUSE=y
#CONFIG_82C710_MOUSEis not set
#CONFIG_PC110_PADis not set#
# Joysticks
#
#CONFIG_JOYSTICKis not set#
# Input core support is needed for joysticks
#
#CONFIG_QIC02_TAPEis not set#
# Watchdog Cards
#CONFIG_WATCHDOG=y
#CONFIG_WATCHDOG_NOWAYOUTis not set
#CONFIG_SOFT_WATCHDOGis not set
#CONFIG_WDTis not set
#CONFIG_WDTPCIis not set
#CONFIG_PCWATCHDOGis not set
#CONFIG_ACQUIRE_WDTis not set
#CONFIG_ADVANTECH_WDTis not set
#CONFIG_60XX_WDTis not set
#CONFIG_MIXCOMWDis not set
#CONFIG_I810_TCOis not set
#CONFIG_MACHZ_WDTis not set
#CONFIG_INTEL_RNGis not set
#CONFIG_NVRAMis not setCONFIG_RTC=y
#CONFIG_DTLKis not set
#CONFIG_R3964is not set
#CONFIG_APPLICOMis not set#
# Ftape, the floppy tape device driver
#
#CONFIG_FTAPEis not setCONFIG_AGP=yCONFIG_AGP_INTEL=yCONFIG_AGP_I810=yCONFIG_AGP_VIA=yCONFIG_AGP_AMD=y
#CONFIG_AGP_SISis not set
#CONFIG_AGP_ALIis not setCONFIG_DRM=yCONFIG_DRM_TDFX=y
#CONFIG_DRM_GAMMAis not set
#CONFIG_DRM_R128is not setCONFIG_DRM_RADEON=y
#CONFIG_DRM_I810is not set
#CONFIG_DRM_MGAis not set#
# Multimedia devices
#
#CONFIG_VIDEO_DEVis not set#
# File systems
#
#CONFIG_QUOTAis not set
#CONFIG_AUTOFS_FSis not set
#CONFIG_AUTOFS4_FSis not set
#CONFIG_REISERFS_FSis not set
#CONFIG_REISERFS_CHECKis not set
#CONFIG_ADFS_FSis not set
#CONFIG_ADFS_FS_RWis not set
#CONFIG_AFFS_FSis not set
#CONFIG_HFS_FSis not set
#CONFIG_BFS_FSis not setCONFIG_FAT_FS=yCONFIG_MSDOS_FS=y
#CONFIG_UMSDOS_FSis not setCONFIG_VFAT_FS=y
#CONFIG_EFS_FSis not set
#CONFIG_JFFS_FSis not set
#CONFIG_CRAMFSis not setCONFIG_TMPFS=y
#CONFIG_RAMFSis not setCONFIG_ISO9660_FS=y
#CONFIG_JOLIETis not set
#CONFIG_MINIX_FSis not set
#CONFIG_NTFS_FSis not set
#CONFIG_NTFS_RWis not set
#CONFIG_HPFS_FSis not setCONFIG_PROC_FS=y
#CONFIG_DEVFS_FSis not set
#CONFIG_DEVFS_MOUNTis not set
#CONFIG_DEVFS_DEBUGis not setCONFIG_DEVPTS_FS=y
#CONFIG_QNX4FS_FSis not set
#CONFIG_QNX4FS_RWis not set
#CONFIG_ROMFS_FSis not setCONFIG_EXT2_FS=y
#CONFIG_SYSV_FSis not set
#CONFIG_SYSV_FS_WRITEis not set
#CONFIG_UDF_FSis not set
#CONFIG_UDF_RWis not set
#CONFIG_UFS_FSis not set
#CONFIG_UFS_FS_WRITEis not set#
# Network File Systems
#
#CONFIG_CODA_FSis not setCONFIG_NFS_FS=yCONFIG_NFS_V3=y
#CONFIG_ROOT_NFSis not set
#CONFIG_NFSDis not set
#CONFIG_NFSD_V3is not setCONFIG_SUNRPC=yCONFIG_LOCKD=yCONFIG_LOCKD_V4=y
#CONFIG_SMB_FSis not set
#CONFIG_NCP_FSis not set
#CONFIG_NCPFS_PACKET_SIGNINGis not set
#CONFIG_NCPFS_IOCTL_LOCKINGis not set
#CONFIG_NCPFS_STRONGis not set
#CONFIG_NCPFS_NFS_NSis not set
#CONFIG_NCPFS_OS2_NSis not set
#CONFIG_NCPFS_SMALLDOSis not set
#CONFIG_NCPFS_NLSis not set
#CONFIG_NCPFS_EXTRASis not set#
# Partition Types
#
#CONFIG_PARTITION_ADVANCEDis not setCONFIG_MSDOS_PARTITION=y
#CONFIG_SMB_NLSis not setCONFIG_NLS=y#
# Native Language Support
#CONFIG_NLS_DEFAULT="iso8859-1"
#CONFIG_NLS_CODEPAGE_437is not set
#CONFIG_NLS_CODEPAGE_737is not set
#CONFIG_NLS_CODEPAGE_775is not set
#CONFIG_NLS_CODEPAGE_850is not set
#CONFIG_NLS_CODEPAGE_852is not set
#CONFIG_NLS_CODEPAGE_855is not set
#CONFIG_NLS_CODEPAGE_857is not set
#CONFIG_NLS_CODEPAGE_860is not set
#CONFIG_NLS_CODEPAGE_861is not set
#CONFIG_NLS_CODEPAGE_862is not set
#CONFIG_NLS_CODEPAGE_863is not set
#CONFIG_NLS_CODEPAGE_864is not set
#CONFIG_NLS_CODEPAGE_865is not set
#CONFIG_NLS_CODEPAGE_866is not set
#CONFIG_NLS_CODEPAGE_869is not set
#CONFIG_NLS_CODEPAGE_936is not set
#CONFIG_NLS_CODEPAGE_950is not set
#CONFIG_NLS_CODEPAGE_932is not set
#CONFIG_NLS_CODEPAGE_949is not set
#CONFIG_NLS_CODEPAGE_874is not set
#CONFIG_NLS_ISO8859_8is not set
#CONFIG_NLS_CODEPAGE_1251is not set
#CONFIG_NLS_ISO8859_1is not set
#CONFIG_NLS_ISO8859_2is not set
#CONFIG_NLS_ISO8859_3is not set
#CONFIG_NLS_ISO8859_4is not set
#CONFIG_NLS_ISO8859_5is not set
#CONFIG_NLS_ISO8859_6is not set
#CONFIG_NLS_ISO8859_7is not set
#CONFIG_NLS_ISO8859_9is not set
#CONFIG_NLS_ISO8859_13is not set
#CONFIG_NLS_ISO8859_14is not set
#CONFIG_NLS_ISO8859_15is not set
#CONFIG_NLS_KOI8_Ris not set
#CONFIG_NLS_KOI8_Uis not set
#CONFIG_NLS_UTF8is not set#
# Console drivers
#CONFIG_VGA_CONSOLE=y
#CONFIG_VIDEO_SELECTis not set
#CONFIG_MDA_CONSOLEis not set#
# Frame-buffer support
#
#CONFIG_FBis not set#
# Sound
#CONFIG_SOUND=y
#CONFIG_SOUND_CMPCIis not setCONFIG_SOUND_EMU10K1=y
#CONFIG_SOUND_FUSIONis not set
#CONFIG_SOUND_CS4281is not set
#CONFIG_SOUND_ES1370is not set
#CONFIG_SOUND_ES1371is not set
#CONFIG_SOUND_ESSSOLO1is not set
#CONFIG_SOUND_MAESTROis not set
#CONFIG_SOUND_MAESTRO3is not set
#CONFIG_SOUND_ICHis not set
#CONFIG_SOUND_SONICVIBESis not set
#CONFIG_SOUND_TRIDENTis not set
#CONFIG_SOUND_MSNDCLASis not set
#CONFIG_SOUND_MSNDPINis not set
#CONFIG_SOUND_VIA82CXXXis not set
#CONFIG_SOUND_OSSis not set
#CONFIG_SOUND_TVMIXERis not set#
# USB support
#CONFIG_USB=y
#CONFIG_USB_DEBUGis not set#
# Miscellaneous USB options
#
#CONFIG_USB_DEVICEFSis not set
#CONFIG_USB_BANDWIDTHis not set#
# USB Controllers
#CONFIG_USB_UHCI_ALT=y
#CONFIG_USB_OHCIis not set#
# USB Device Class drivers
#
#CONFIG_USB_AUDIOis not set
#CONFIG_USB_BLUETOOTHis not setCONFIG_USB_STORAGE=y
#CONFIG_USB_STORAGE_DEBUGis not set
#CONFIG_USB_STORAGE_FREECOMis not set
#CONFIG_USB_ACMis not set
#CONFIG_USB_PRINTERis not set#
# USB Human Interface Devices (HID)
##
# Input core support is needed for USB HID
##
# USB Imaging devices
#
#CONFIG_USB_DC2XXis not set
#CONFIG_USB_MDC800is not set
#CONFIG_USB_SCANNERis not set
#CONFIG_USB_MICROTEKis not set#
# USB Multimedia devices
#
#CONFIG_USB_IBMCAMis not set
#CONFIG_USB_OV511is not set
#CONFIG_USB_DSBRis not set
#CONFIG_USB_DABUSBis not set#
# USB Network adaptors
#
#CONFIG_USB_PLUSBis not set
#CONFIG_USB_PEGASUSis not set
#CONFIG_USB_NET1080is not set#
# USB port drivers
#
#CONFIG_USB_USS720is not set#
# USB Serial Converter support
#
#CONFIG_USB_SERIALis not set#
# USB misc drivers
#
#CONFIG_USB_RIO500is not set#
# Kernel hacking
#
#CONFIG_MAGIC_SYSRQis not set--
++++++++++++++++++++++++++++++++++++++++++++++
Dave Neal, Center for Nonlinear Studies
Phone w/ Voice Mail (505) 665-6471
Digital Pager - (505) 664-8666
Wirth's Law: Software gets slower faster than
Hardware gets faster!
++++++++++++++++++++++++++++++++++++++++++++++
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 4 lines
I just wanted to throw in my two cents and say that there appear to be widespread issues with the APIC code in 2.4.x. I'm tempted to stick my neck out and say that it might be best to disable SMP IOAPIC by default until APIC can be massaged, at least for a wider variety of hardware.
I would disagree
There are five cases I am seeing
1. Serverworks total APIC hose ups.
Fix: remove OSB4 or use -ac tree
2. 440BX and similar boards losing interrupts on some drivers
Fix: use -ac
3. APIC errors notably checksum errors.
Fix: buy properly manufactured hardware
4. Hangs on boot with the CUV4XD and a couple of other boards.
Still a mystery
5. Incorrect PCI IRQ routing
Fix: Mostly get a board with a correct BIOS. There are a couple of cases people are looking at - some are fixed in 2.4.4 and -ac where magic IRQ lines are not visible directly in PCI space
On Thu, 3 May 2001, Alan Cox wrote on APIC problems in 2.4:
Quoted 5 lines
There are five cases I am seeing
1. Serverworks total APIC hose ups.
Fix: remove OSB4 or use -ac tree
2. 440BX and similar boards losing interrupts on some drivers
Fix: use -ac
Quoted 8 lines
3. APIC errors notably checksum errors.
Fix: buy properly manufactured hardware
4. Hangs on boot with the CUV4XD and a couple of other boards.
Still a mystery
5. Incorrect PCI IRQ routing
Fix: Mostly get a board with a correct BIOS. There are a couple of cases people are looking at - some are fixed in 2.4.4 and -ac where magic IRQ lines are not visible directly in PCI space
Doesn't 2.4.1-ac1 onwards contain:
o Workaround code for APIC problems with ne2k (Maciej Rozycki)
| this will break original 82489DX devices for now | ie _very_ early dual pentium boards
Got good reviews at the time, and I thought it was more general than ne2k. I don't remember it going forward to Linus (but I've not looked).
Hugh
Quoted 2 lines
Got good reviews at the time, and I thought it was more general than ne2k. I don't remember it going forward to Linus (but I've not looked).
ne2k is the big one it shows up on. Its on my for Linus list in the next few pushes of stuff.
I'm losing the timer interrupt, but it's not driver-specific -- only the motherboard is required to reproduce for me; different SCSI, RAID, and ether drivers have been swapped out. Nothing with "HP" on it seems to work, and it wouldn't surprise me in the least to find out that HP's stuff is broken. But this problem has existed since 2.4.0-test1 and hasn't changed, and it surprises me that at least a work-around hasn't been merged into "the" kernel by now.
There might be fixes in the -ac tree that effect my problem -- I'll try the latest -ac and see what happens. Thanks for the suggestion.
But the distributions use _the_ kernel. Even if -ac is fixed, it's not really something I would be willing to put in production. Until I found the noapic work-around, we were basically going to have to move off of Linux. I could very well be an isolated case, but the APIC issues I'm seeing scare me, and not just for my sake.
I mean all of this in the utmost respect -- I just felt that this issue needs a little more light shed on it, and I'm here to help in any way I can. --
Ken.
Quoted 31 lines · Hugh Dickins
On Thu, 3 May 2001, Alan Cox wrote on APIC problems in 2.4:
Quoted 5 lines
There are five cases I am seeing
1. Serverworks total APIC hose ups.
Fix: remove OSB4 or use -ac tree
2. 440BX and similar boards losing interrupts on some drivers
Fix: use -acQuoted 8 lines
3. APIC errors notably checksum errors.
Fix: buy properly manufactured hardware
4. Hangs on boot with the CUV4XD and a couple of other boards.
Still a mystery
5. Incorrect PCI IRQ routing
Fix: Mostly get a board with a correct BIOS. There are a couple of cases people are looking at - some are fixed in 2.4.4 and -ac where magic IRQ lines are not visible directly in PCI spaceDoesn't 2.4.1-ac1 onwards contain:
o Workaround code for APIC problems with ne2k (Maciej Rozycki)
| this will break original 82489DX devices for now | ie _very_ early dual pentium boardsGot good reviews at the time, and I thought it was more general than ne2k. I don't remember it going forward to Linus (but I've not looked).
Hugh
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 2 lines
But the distributions use _the_ kernel. Even if -ac is fixed, it's not really something I would be willing to put in production. Until I found
Actually by unit count Linus is currently losing to me on 2.4 shipping. Thats one reason I really want to get the stuff I have back into the main tree.
Quoted 3 lines
the noapic work-around, we were basically going to have to move off of Linux. I could very well be an isolated case, but the APIC issues I'm seeing scare me, and not just for my sake.
Can you give me the detailed boot up messages from one of your HP boxes and some more info. Also can you run dmidecode.c from
ftp://ftp.linux.org.uk/pub/linux/alan
on them and send me the DMI strings. You will need to run it as root but it can be run on a live system (at least I dont know of any bugs in it and it only reads from raw BIOS memory not writes).
Alan
I have some info at "http://web.irridia.com/linux/" from an LPr having issues, including the dmidecode output and a mostly complete boot-time dmesg dump from an LPr and LP1000r. The LPr was running 2.4.2-pre4 and the LP1000r is running 2.4.5-pre1, both without "noapic". Please let me know if you need more info.
BTW, I have an isolated bank of redundant machines, one of which I can load down with heavy live load so I can test patches pretty easily. I'll do anything, including setting fire to a machine, if it'll help. :-) --
Ken.
Quoted 20 lines · Alan Cox
Quoted 2 lines
But the distributions use _the_ kernel. Even if -ac is fixed, it's not really something I would be willing to put in production. Until I found
Actually by unit count Linus is currently losing to me on 2.4 shipping. Thats one reason I really want to get the stuff I have back into the main tree.
Quoted 3 lines
the noapic work-around, we were basically going to have to move off of Linux. I could very well be an isolated case, but the APIC issues I'm seeing scare me, and not just for my sake.
Can you give me the detailed boot up messages from one of your HP boxes and some more info. Also can you run
dmidecode.cfrom
ftp://ftp.linux.org.uk/pub/linux/alanon them and send me the DMI strings. You will need to run it as root but it can be run on a live system (at least I dont know of any bugs in it and it only reads from raw BIOS memory not writes).
Alan
All,
I unfortunately don't have the time this evening to produce actual kernel messages, but I did want to throw out that I have an ASUS CUV4X-DLS board too, with two PIII/1GHz processors in it, and I cannot get it to boot an SMP kernel at all. In addition to the built-in devices, the following cards are also present:
* Netgear FA310TX (rev. D, I believe - lspci reports it as a Lite-On LNE100TX rev 21)
* Promise PDC20267 Ultra100 controller
* Creative SB Live! Value
* Matrox G200 AGP
When it gets to the point of activating the second processor, kernel 2.4.3-ac13 starts spewing:
probable hardware bug: clock timer configuration lost - probably a VIA686a motherboard. probable hardware bug: restoring chip configuration.
continuously. Older kernels simply hang at this point. I'll try to get the actual messages leading up to this tomorrow. Also, if there's any other information I can collect from my system that could help, feel free to ask. I'll also build 2.4.4-ac6 on it tomorrow and try booting it SMP. Here's the output of lspci -vvvvvv:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Subsystem: Asustek Computer, Inc.: Unknown device 8038
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=32M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000dfff
Memory behind bridge: f9800000-fadfffff
Prefetchable memory behind bridge: faf00000-fbffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: Asustek Computer, Inc.: Unknown device 8038
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corporation EtherExpress PRO/100+ Management Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b800 [size=64]
Region 2: Memory at f8800000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:08.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c1010 Ultra3 SCSI Adapter (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 4500ns max), cache line size 08 Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at b400 [size=256] Region 1: Memory at f8000000 (64-bit, non-prefetchable) [size=1K] Region 3: Memory at f7800000 (64-bit, non-prefetchable) [size=8K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c1010 Ultra3 SCSI Adapter (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 4500ns max), cache line size 08 Interrupt: pin B routed to IRQ 11 Region 0: I/O ports at b000 [size=256] Region 1: Memory at f7000000 (64-bit, non-prefetchable) [size=1K] Region 3: Memory at f6800000 (64-bit, non-prefetchable) [size=8K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 21)
Subsystem: Netgear FA310TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at a800 [size=256]
Region 1: Memory at f6000000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=256K]
00:0b.0 Unknown mass storage controller: Promise Technology, Inc. 20267 (rev 02)
Subsystem: Promise Technology, Inc.: Unknown device 4d33 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at a400 [size=8] Region 1: I/O ports at a000 [size=4] Region 2: I/O ports at 9800 [size=8] Region 3: I/O ports at 9400 [size=4] Region 4: I/O ports at 9000 [size=64] Region 5: Memory at f5800000 (32-bit, non-prefetchable) [size=128K] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [58] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 08)
Subsystem: Creative Labs CT4832 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 8800 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.1 Input device controller: Creative Labs SB Live! (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at 8400 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev 01) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G200 AGP
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fb000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fa000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at f9800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at faff0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x2
Here is the dmesg output from a single-processor boot of 2.4.3-ac13, although I don't know how much use this is:
Linux version 2.4.3-ac13 (root@balance) (gcc version 2.95.4 20010319 (Debian prerelease)) #104 Sat Apr 28 19:42:43 PDT 2001 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fffc000 (usable)
BIOS-e820: 000000000fffc000 - 000000000ffff000 (ACPI data)
BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=243ac13 ro root=302 mem=256M ether=0,0,eth0 ether=0,0,eth1 nmi_watchdog=0 Initializing CPU#0
Detected 1004.542 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2005.40 BogoMIPS
Memory: 255168k/262144k available (1268k kernel code, 6588k reserved, 474k data, 228k init, 0k highmem) Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0d00, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Disabled enhanced CPU to PCI posting
PCI: Disabled enhanced CPU to PCI posting #2
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
IA-32 Microcode Update Driver: v1.08 <[email protected]>
Starting kswapd v1.8
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ... SMSC Super-IO detection, now testing Ports 2F0, 370 ...0x378: FIFO is 16 bytes0x378: writeIntrThreshold is 80x378: readIntrThreshold is 80x378: PWord is 8 bits0x378: Interrupts are ISA-Pulses0x378: ECP port cfgA=0x10 cfgB=0x000x378: ECP settings irq=<none or set by other means> dma=<none or set by other means>
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,COMPAT,ECP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)parport_pc: Via 686A parallel port: io=0x378
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
lp0: using parport0 (polling).
block: queued sectors max/low 169506kB/56502kB, 512 slots per queue Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller on PCI bus 00 dev 21VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMAPDC20267: IDE controller on PCI bus 00 dev 58
PCI: Found IRQ 10 for device 00:0b.0
PCI: The same IRQ used for device 00:07.0
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0x9000-0x9007, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x9008-0x900f, BIOS settings: hdg:DMA, hdh:piohda: QUANTUM FIREBALL ST4.3A, ATA DISK drive
hdc: Pioneer CD-ROM ATAPI Model DR-A14S 0104, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR CD-R PX-W1610A, ATAPI CD/DVD-ROM drive
hdg: IBM-DTLA-307075, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide3 at 0x9800-0x9807,0x9402 on irq 10
hda: 8418816 sectors (4310 MB) w/81KiB Cache, CHS=14848/9/63, UDMA(33)
hdg: 150136560 sectors (76870 MB) w/1916KiB Cache, CHS=148945/16/63, UDMA(100) Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 > /dev/ide/host2/bus1/target0/lun0: p1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
devfs: v0.102 (20000622) Richard Gooch ([email protected])
devfs: boot_options: 0x0
loop: loaded (max 8 devices)
Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10d
Linux Tulip driver version 0.9.14e (April 20, 2001)
PCI: Found IRQ 5 for device 00:0a.0
00:0a.0: MII transceiver #1 config 1000 status 782d advertising 01e1.
eth0: Lite-On 82c168 PNIC rev 33 at 0xa800, 00:A0:CC:3C:A8:DB, IRQ 5. eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.htmleepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
PCI: Found IRQ 10 for device 00:07.0
PCI: The same IRQ used for device 00:0b.0
eth1: Intel Corporation 82557 [Ethernet Pro 100], 00:E0:18:05:A9:70, IRQ 10.
Board assembly 733470-006, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
PPP generic driver version 2.4.1
PPP Deflate Compression module registered
PPP BSD Compression module registered
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 9 for device 00:08.0
sym53c8xx: at PCI bus 0, device 8, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-33 detected with Symbios NVRAM
PCI: Found IRQ 11 for device 00:08.1
PCI: The same IRQ used for device 00:0c.0
PCI: The same IRQ used for device 01:00.0
sym53c8xx: at PCI bus 0, device 8, function 1
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-33 detected with Symbios NVRAM
sym53c1010-33-0: rev 0x1 on pci bus 0 device 8 function 0 irq 9
sym53c1010-33-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-33-0: on-chip RAM at 0xf7800000
sym53c1010-33-0: restart (scsi reset).
sym53c1010-33-0: handling phase mismatch from SCRIPTS.
sym53c1010-33-0: Downloading SCSI SCRIPTS.
sym53c1010-33-1: rev 0x1 on pci bus 0 device 8 function 1 irq 11
sym53c1010-33-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-33-1: on-chip RAM at 0xf6800000
sym53c1010-33-1: restart (scsi reset).
sym53c1010-33-1: handling phase mismatch from SCRIPTS.
sym53c1010-33-1: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx-1.7.3b-20010407
scsi1 : sym53c8xx-1.7.3b-20010407
Vendor: SEAGATE Model: ST39103LW Rev: 0001
Type: Direct-Access ANSI SCSI revision: 02
sym53c1010-33-0-<0,0>: tagged command queue depth set to 32
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PIONEER Model: CD-ROM DR-A14S Rev: 1.04 Type: CD-ROM ANSI SCSI revision: 02 Vendor: PLEXTOR Model: CD-R PX-W1610A Rev: 1.00 Type: CD-ROM ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 sym53c1010-33-0-<0,0>: phase change 6-7 11@015734b8 resid=2. sym53c1010-33-0-<0,*>: FAST-40 WIDE SCSI 80.0 MB/s (25.0 ns, offset 15) SCSI device sda: 17783240 512-byte hdwr sectors (9105 MB)
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 >
Attached scsi CD-ROM sr0 at scsi2, channel 0, id 0, lun 0 Attached scsi CD-ROM sr1 at scsi2, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384) ip_conntrack (2048 buckets, 16384 max)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 228k freed
Adding Swap: 65732k swap-space (priority 1)
Adding Swap: 128480k swap-space (priority 2)
reiserfs: checking transaction log (device 03:03) ...
Using tea hash to sort names
reiserfs: using 3.5.x disk format
ReiserFS version 3.6.25
Quoted 5 lines
When it gets to the point of activating the second processor, kernel 2.4.3-ac13 starts spewing:
probable hardware bug: clock timer configuration lost - probably a VIA686a motherboard. probable hardware bug: restoring chip configuration.
That is useful informtion. The kernel is seeing the interval timer overrun which implies things are very very stuck