fealnx problem

DISCUSSION Jon Forsberg 2 participants 4 messages Jun 21, 2001 – Jun 22, 2001 Network drivers

Share & tools

Jon Forsberg

author

2001-06-21 13:00 UTC #0 lore raw

I have an Surecom EP-320X-S Ethernet adapter which apparently uses a Myson MTD-8xx chip. It works well with the "fealnx" driver (labeled "Myson MTD-8xx PCI Ethernet support" in kernel config) except for one thing:
After a while in use it stops working and prints

Jun 21 12:18:18 naut kernel: NETDEV WATCHDOG: eth0: transmit timed out
Jun 21 12:18:18 naut kernel: eth0: Transmit timed out, status 00000000, resetting...
Jun 21 12:18:18 naut kernel:   Rx ring c1272140:  80000000 80000000 80000000 80000000 80000000 80000000 80000000 80000000 80000000 80000000 80000000 80000000
Jun 21 12:18:18 naut kernel:   Tx ring c12722c0:  80000000 80000000 80000000 80000000 80000000 0000

a few times in the kernel log. Then I have to bring the interface down and up again (ifdown/ifup) to get it working. It seems that the higher network load the sooner it will stop working, but it always does eventually. It's impossible to transfer a large file (over, say 5 MB) via FTP for example, but with scp it often works (the encryption makes the transfer slower).

CC me. thanks,
--zzed

#
# Automatically generated by make menuconfig: don't edit #
CONFIG_X86=y
CONFIG_ISA=y
# CONFIG_SBUS is not set
CONFIG_UID16=y

#
# Code maturity level options
#
# CONFIG_EXPERIMENTAL is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y

#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
CONFIG_M686=y
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
# CONFIG_TOSHIBA is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_SMP is not set
# CONFIG_X86_UP_IOAPIC is not set

#
# General setup
#
CONFIG_NET=y
# CONFIG_VISWS is not set
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_HOTPLUG=y

#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_PM=y
# CONFIG_APM is not set

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_SUNBPP is not set
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y

#
# Plug and Play configuration
#
# CONFIG_PNP is not set
# CONFIG_ISAPNP is not set

#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set

#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_BLK_DEV_LVM is not set

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
# CONFIG_FILTER is not set
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_INET_ECN is not set
# CONFIG_SYN_COOKIES is not set

#
# IP: Netfilter Configuration
#
# CONFIG_IP_NF_CONNTRACK is not set
# CONFIG_IP_NF_IPTABLES is not set
# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
# CONFIG_IP_NF_COMPAT_IPFWADM is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set

#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y

#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
# CONFIG_BLK_DEV_COMMERIAL is not set
# CONFIG_BLK_DEV_TIVO is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_AEC62XX_TUNING is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD7409 is not set
# CONFIG_AMD7409_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_PIIX_TUNING is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_OSB4 is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y

#
# SCSI support
#
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=y
CONFIG_SCSI_DEBUG_QUEUES=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
CONFIG_SCSI_PPA=y
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_IZIP_EPP16 is not set
# CONFIG_SCSI_IZIP_SLOW_CTR is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set

#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set

#
# Network device support
#
CONFIG_NETDEVICES=y

#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_TULIP is not set
# CONFIG_DE4X5 is not set
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
# CONFIG_EEPRO100 is not set
# CONFIG_EEPRO100_PM is not set
# CONFIG_LNE390 is not set
CONFIG_FEALNX=y
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139TOO is not set
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_NET_POCKET is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_HAMACHI is not set
# CONFIG_SK98LIN is not set
# CONFIG_FDDI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set

#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set

#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set

#
# ISDN subsystem
#
CONFIG_ISDN=y
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
# CONFIG_ISDN_PPP_BSDCOMP is not set
CONFIG_ISDN_AUDIO=y
# CONFIG_ISDN_TTY_FAX is not set
# CONFIG_ISDN_X25 is not set

#
# ISDN feature submodules
#
# CONFIG_ISDN_DRV_LOOP is not set
# CONFIG_ISDN_DIVERSION is not set

#
# Passive ISDN cards
#
CONFIG_ISDN_DRV_HISAX=m
CONFIG_HISAX_EURO=y
# CONFIG_DE_AOC is not set
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
# CONFIG_HISAX_1TR6 is not set
# CONFIG_HISAX_NI1 is not set
# CONFIG_HISAX_16_0 is not set
# CONFIG_HISAX_16_3 is not set
# CONFIG_HISAX_TELESPCI is not set
# CONFIG_HISAX_S0BOX is not set
# CONFIG_HISAX_AVM_A1 is not set
# CONFIG_HISAX_FRITZPCI is not set
# CONFIG_HISAX_AVM_A1_PCMCIA is not set
# CONFIG_HISAX_ELSA is not set
# CONFIG_HISAX_IX1MICROR2 is not set
# CONFIG_HISAX_DIEHLDIVA is not set
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
# CONFIG_HISAX_HFCS is not set
# CONFIG_HISAX_SEDLBAUER is not set
# CONFIG_HISAX_SPORTSTER is not set
# CONFIG_HISAX_MIC is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
# CONFIG_HISAX_HFC_PCI is not set
CONFIG_HISAX_W6692=y
# CONFIG_HISAX_SEDLBAUER_CS is not set
# CONFIG_HISAX_ELSA_CS is not set

#
# Active ISDN cards
#
# CONFIG_ISDN_DRV_ICN is not set
# CONFIG_ISDN_DRV_PCBIT is not set
# CONFIG_ISDN_DRV_SC is not set
# CONFIG_ISDN_DRV_ACT2000 is not set
# CONFIG_ISDN_DRV_EICON is not set
# CONFIG_ISDN_CAPI is not set
# CONFIG_HYSDN is not set
# CONFIG_HYSDN_CAPI is not set

#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set

#
# Input core support
#
# CONFIG_INPUT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
# CONFIG_PRINTER is not set
# CONFIG_PPDEV is not set

#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_PHILIPSPAR is not set
# CONFIG_I2C_ELV is not set
# CONFIG_I2C_VELLEMAN is not set
# CONFIG_I2C_ALGOPCF is not set
CONFIG_I2C_CHARDEV=y

#
# Mice
#
# CONFIG_BUSMOUSE is not set
# CONFIG_MOUSE is not set

#
# Joysticks
#
# CONFIG_JOYSTICK is not set
# CONFIG_QIC02_TAPE is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_INTEL_RNG is not set
# CONFIG_NVRAM is not set
# CONFIG_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
CONFIG_AGP_INTEL=y
CONFIG_AGP_I810=y
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not set
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not set
# CONFIG_DRM_RADEON is not set
CONFIG_DRM_I810=y
# CONFIG_DRM_MGA is not set

#
# Multimedia devices
#
CONFIG_VIDEO_DEV=y

#
# Video For Linux
#
CONFIG_VIDEO_PROC_FS=y
# CONFIG_I2C_PARPORT is not set
CONFIG_VIDEO_BT848=y
# CONFIG_VIDEO_PMS is not set
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_TUNER_3036 is not set
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_BUZ is not set
# CONFIG_VIDEO_ZR36120 is not set

#
# Radio Adapters
#
# CONFIG_RADIO_CADET is not set
# CONFIG_RADIO_RTRACK is not set
# CONFIG_RADIO_RTRACK2 is not set
# CONFIG_RADIO_AZTECH is not set
# CONFIG_RADIO_GEMTEK is not set
# CONFIG_RADIO_MAXIRADIO is not set
# CONFIG_RADIO_MAESTRO is not set
# CONFIG_RADIO_MIROPCM20 is not set
# CONFIG_RADIO_SF16FMI is not set
# CONFIG_RADIO_TERRATEC is not set
# CONFIG_RADIO_TRUST is not set
# CONFIG_RADIO_TYPHOON is not set
# CONFIG_RADIO_ZOLTRIX is not set

#
# File systems
#
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_REISERFS_FS is not set
# CONFIG_REISERFS_CHECK is not set
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BFS_FS is not set
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
# CONFIG_UMSDOS_FS is not set
CONFIG_VFAT_FS=y
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_TMPFS is not set
# CONFIG_RAMFS is not set
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_MINIX_FS is not set
# CONFIG_VXFS_FS is not set
CONFIG_NTFS_FS=y
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_SYSV_FS_WRITE is not set
CONFIG_UDF_FS=y
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set

#
# Network File Systems
#
CONFIG_CODA_FS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_ROOT_NFS is not set
CONFIG_NFSD=y
# CONFIG_NFSD_V3 is not set
CONFIG_SUNRPC=y
CONFIG_LOCKD=y
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y

#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ISO8859_1 is not set
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set

#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VIDEO_SELECT is not set

#
# Sound
#
CONFIG_SOUND=y
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
CONFIG_SOUND_ES1371=y
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set
CONFIG_SOUND_TVMIXER=y

#
# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
CONFIG_USB_UHCI_ALT=y
# CONFIG_USB_OHCI is not set
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH is not set
# CONFIG_USB_STORAGE is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
# CONFIG_USB_DC2XX is not set
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_PWC is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_PLUSB is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_NET1080 is not set
# CONFIG_USB_USS720 is not set

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
# CONFIG_USB_RIO500 is not set

#
# Kernel hacking
#
CONFIG_MAGIC_SYSRQ=y

Jun 19 19:09:00 naut kernel: klogd 1.3-3#33.1, log source = /proc/kmsg started.
Jun 19 19:09:01 naut kernel: Inspecting /boot/System.map-2.4.5
Jun 19 19:09:01 naut kernel: Loaded 16496 symbols from /boot/System.map-2.4.5.
Jun 19 19:09:01 naut kernel: Symbols match kernel version 2.4.5.
Jun 19 19:09:01 naut kernel: No module symbols loaded.
Jun 19 19:09:01 naut kernel: Linux version 2.4.5 (zzed@naut) (gcc version 2.95.2 20000220 (Debian GNU/Linux)) #7 lör jun 9 22:55:14 CEST 2001
Jun 19 19:09:01 naut kernel: BIOS-provided physical RAM map:
Jun 19 19:09:01 naut kernel:  BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
Jun 19 19:09:01 naut kernel:  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Jun 19 19:09:01 naut kernel:  BIOS-e820: 0000000000100000 - 0000000007eeb000 (usable)
Jun 19 19:09:01 naut kernel:  BIOS-e820: 0000000007eeb000 - 0000000007eef000 (ACPI data)
Jun 19 19:09:01 naut kernel:  BIOS-e820: 0000000007eef000 - 0000000007eff000 (reserved)
Jun 19 19:09:01 naut kernel:  BIOS-e820: 0000000007eff000 - 0000000007f00000 (ACPI NVS)
Jun 19 19:09:01 naut kernel:  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Jun 19 19:09:01 naut kernel: On node 0 totalpages: 32491
Jun 19 19:09:01 naut kernel: zone(0): 4096 pages.
Jun 19 19:09:01 naut kernel: zone(1): 28395 pages.
Jun 19 19:09:01 naut kernel: zone(2): 0 pages.
Jun 19 19:09:01 naut kernel: Kernel command line: auto BOOT_IMAGE=Linux ro root=302 BOOT_FILE=/boot/vmlinuz hda=13410,15,63 hdc=scsi bttv.radio=1 hisax=36,2
Jun 19 19:09:01 naut kernel: ide_setup: hda=13410,15,63
Jun 19 19:09:01 naut kernel: ide_setup: hdc=scsi
Jun 19 19:09:01 naut kernel: Initializing CPU#0
Jun 19 19:09:01 naut kernel: Detected 668.194 MHz processor.
Jun 19 19:09:01 naut kernel: Console: colour VGA+ 80x25
Jun 19 19:09:01 naut kernel: Calibrating delay loop... 1333.65 BogoMIPS
Jun 19 19:09:01 naut kernel: Memory: 125040k/129964k available (1416k kernel code, 4540k reserved, 548k data, 180k init, 0k highmem)
Jun 19 19:09:01 naut kernel: Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Jun 19 19:09:01 naut kernel: Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Jun 19 19:09:01 naut kernel: Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Jun 19 19:09:01 naut kernel: Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jun 19 19:09:01 naut kernel: CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
Jun 19 19:09:01 naut kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Jun 19 19:09:01 naut kernel: CPU: L2 cache: 128K
Jun 19 19:09:01 naut kernel: Intel machine check architecture supported.
Jun 19 19:09:01 naut kernel: Intel machine check reporting enabled on CPU#0.
Jun 19 19:09:01 naut kernel: CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
Jun 19 19:09:01 naut kernel: CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
Jun 19 19:09:01 naut kernel: CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
Jun 19 19:09:01 naut kernel: CPU: Intel Celeron (Coppermine) stepping 03
Jun 19 19:09:01 naut kernel: Enabling fast FPU save and restore... done.
Jun 19 19:09:01 naut kernel: Enabling unmasked SIMD FPU exception support... done.
Jun 19 19:09:01 naut kernel: Checking 'hlt' instruction... OK.
Jun 19 19:09:01 naut kernel: POSIX conformance testing by UNIFIX
Jun 19 19:09:01 naut kernel: mtrr: v1.40 (20010327) Richard Gooch ([email protected])
Jun 19 19:09:01 naut kernel: mtrr: detected mtrr type: Intel
Jun 19 19:09:01 naut kernel: PCI: PCI BIOS revision 2.10 entry at 0xf0960, last bus=1
Jun 19 19:09:01 naut kernel: PCI: Using configuration type 1
Jun 19 19:09:01 naut kernel: PCI: Probing PCI hardware
Jun 19 19:09:01 naut kernel: PCI: Discovered primary peer bus fe [IRQ]
Jun 19 19:09:01 naut kernel: PCI: Using IRQ router PIIX [8086/2440] at 00:1f.0
Jun 19 19:09:01 naut kernel: Linux NET4.0 for Linux 2.4
Jun 19 19:09:01 naut kernel: Based upon Swansea University Computer Society NET3.039
Jun 19 19:09:01 naut kernel: Starting kswapd v1.8
Jun 19 19:09:01 naut kernel: Coda Kernel/Venus communications, v5.3.14, [email protected]
Jun 19 19:09:01 naut kernel: NTFS version 010116
Jun 19 19:09:01 naut kernel: udf: registering filesystem
Jun 19 19:09:01 naut kernel: 0x378: FIFO is 16 bytes
Jun 19 19:09:01 naut kernel: 0x378: writeIntrThreshold is 9
Jun 19 19:09:01 naut kernel: 0x378: readIntrThreshold is 9
Jun 19 19:09:01 naut kernel: 0x378: PWord is 8 bits
Jun 19 19:09:01 naut kernel: 0x378: Interrupts are ISA-Pulses
Jun 19 19:09:01 naut kernel: 0x378: ECP port cfgA=0x10 cfgB=0x40
Jun 19 19:09:01 naut kernel: 0x378: ECP settings irq=<none or set by other means> dma=<none or set by other means>
Jun 19 19:09:01 naut kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,COMPAT,ECP]
Jun 19 19:09:01 naut kernel: parport0: irq 7 detected
Jun 19 19:09:01 naut kernel: parport0: cpp_daisy: aa5500ff(38)
Jun 19 19:09:01 naut kernel: parport0: assign_addrs: aa5500ff(38)
Jun 19 19:09:01 naut kernel: parport0: cpp_daisy: aa5500ff(38)
Jun 19 19:09:01 naut kernel: parport0: assign_addrs: aa5500ff(38)
Jun 19 19:09:01 naut kernel: i2c-core.o: i2c core module
Jun 19 19:09:01 naut kernel: i2c-dev.o: i2c /dev entries driver module
Jun 19 19:09:01 naut kernel: i2c-core.o: driver i2c-dev dummy driver registered.
Jun 19 19:09:01 naut kernel: i2c-algo-bit.o: i2c bit algorithm module
Jun 19 19:09:01 naut kernel: pty: 256 Unix98 ptys configured
Jun 19 19:09:01 naut kernel: Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Jun 19 19:09:01 naut kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Jun 19 19:09:01 naut kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Jun 19 19:09:01 naut kernel: block: queued sectors max/low 83037kB/27679kB, 256 slots per queue
Jun 19 19:09:01 naut kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31
Jun 19 19:09:01 naut kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jun 19 19:09:01 naut kernel: PIIX4: IDE controller on PCI bus 00 dev f9
Jun 19 19:09:01 naut kernel: PIIX4: chipset revision 1
Jun 19 19:09:01 naut kernel: PIIX4: not 100%% native mode: will probe irqs later
Jun 19 19:09:01 naut kernel:     ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:DMA
Jun 19 19:09:01 naut kernel:     ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:pio
Jun 19 19:09:01 naut kernel: hda: FUJITSU MPE3064AT, ATA DISK drive
Jun 19 19:09:01 naut kernel: hdb: IBM-DTLA-307045, ATA DISK drive
Jun 19 19:09:01 naut kernel: hdc: RICOH DVD/CDRW MP9060, ATAPI CD/DVD-ROM drive
Jun 19 19:09:01 naut kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Jun 19 19:09:01 naut kernel: ide1 at 0x170-0x177,0x376 on irq 15
Jun 19 19:09:01 naut kernel: hda: 12672450 sectors (6488 MB) w/512KiB Cache, CHS=13410/15/63
Jun 19 19:09:01 naut kernel: hdb: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=5606/255/63
Jun 19 19:09:01 naut kernel: ide-cd: passing drive hdc to ide-scsi emulation.
Jun 19 19:09:01 naut kernel: Partition check:
Jun 19 19:09:01 naut kernel:  hda: hda1 hda2 hda3
Jun 19 19:09:01 naut kernel:  hdb: hdb1
Jun 19 19:09:01 naut kernel: loop: loaded (max 8 devices)
Jun 19 19:09:01 naut kernel: fealnx.c:v2.50 1/17/2001
Jun 19 19:09:01 naut kernel: PCI: Found IRQ 5 for device 01:0c.0
Jun 19 19:09:01 naut kernel: eth0: 100/10M Ethernet PCI Adapter at 0xd000, 00:02:44:04:f2:d0, IRQ 5.
Jun 19 19:09:01 naut kernel: Linux video capture interface: v1.00
Jun 19 19:09:01 naut kernel: i2c-core.o: driver i2c msp3400 driver registered.
Jun 19 19:09:01 naut kernel: tvaudio: TV audio decoder + audio/video mux driver
Jun 19 19:09:01 naut kernel: tvaudio: known chips: tda9840,tda9873h,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951)
Jun 19 19:09:01 naut kernel: i2c-core.o: driver generic i2c audio driver registered.
Jun 19 19:09:01 naut kernel: i2c-core.o: driver i2c TV tuner driver registered.
Jun 19 19:09:01 naut kernel: i2c-core.o: driver tv card mixer driver registered.
Jun 19 19:09:01 naut kernel: bttv: driver version 0.7.57 loaded
Jun 19 19:09:01 naut kernel: bttv: using 2 buffers with 2080k (4160k total) for capture
Jun 19 19:09:01 naut kernel: bttv: Bt8xx card found (0).
Jun 19 19:09:01 naut kernel: PCI: Found IRQ 9 for device 01:0b.0
Jun 19 19:09:01 naut kernel: PCI: The same IRQ used for device 00:1f.4
Jun 19 19:09:01 naut kernel: PCI: The same IRQ used for device 01:0b.1
Jun 19 19:09:01 naut kernel: bttv0: Bt878 (rev 17) at 01:0b.0, irq: 9, latency: 64, memory: 0xf7800000
Jun 19 19:09:01 naut kernel: bttv0: subsystem: 0070:13eb  =>  Hauppauge WinTV  =>  card=10
Jun 19 19:09:01 naut kernel: bttv0: model: BT878(Hauppauge new (bt878)) [autodetected]
Jun 19 19:09:01 naut kernel: bttv0: Hauppauge msp34xx: reset line init
Jun 19 19:09:01 naut kernel: i2c-dev.o: Registered 'bt848 #0' as minor 0
Jun 19 19:09:01 naut kernel: msp34xx: init: chip=MSP3415D-B3, has NICAM support
Jun 19 19:09:01 naut kernel: msp3410: daemon started
Jun 19 19:09:01 naut kernel: bttv0: i2c attach [MSP3415D-B3]
Jun 19 19:09:01 naut kernel: i2c-core.o: client [MSP3415D-B3] registered to adapter [bt848 #0](pos. 0).
Jun 19 19:09:01 naut kernel: tuner: chip found @ 0x61
Jun 19 19:09:01 naut kernel: bttv0: i2c attach [(unset)]
Jun 19 19:09:01 naut kernel: i2c-core.o: client [(unset)] registered to adapter [bt848 #0](pos. 1).
Jun 19 19:09:01 naut kernel: tvmixer: debug: MSP3415D-B3
Jun 19 19:09:01 naut kernel: tvmixer: MSP3415D-B3 (bt848 #0) registered with minor 0
Jun 19 19:09:01 naut kernel: tvmixer: debug: (unset)
Jun 19 19:09:01 naut kernel: i2c-core.o: adapter bt848 #0 registered as adapter 0.
Jun 19 19:09:01 naut kernel: bttv0: Hauppauge eeprom: model=44354, tuner=Philips FM1216 (5), radio=yes
Jun 19 19:09:01 naut kernel: bttv0: i2c: checking for MSP34xx @ 0x80... found
Jun 19 19:09:01 naut kernel: bttv0: i2c: checking for TDA9875 @ 0xb0... not found
Jun 19 19:09:01 naut kernel: bttv0: i2c: checking for TDA7432 @ 0x8a... not found
Jun 19 19:09:01 naut kernel: Linux agpgart interface v0.99 (c) Jeff Hartmann
Jun 19 19:09:01 naut kernel: agpgart: Maximum main memory to use for agp memory: 93M
Jun 19 19:09:01 naut kernel: agpgart: agpgart: Detected an Intel i815 Chipset.
Jun 19 19:09:01 naut kernel: agpgart: AGP aperture is 64M @ 0xf8000000
Jun 19 19:09:01 naut kernel: [drm] AGP 0.99 on Intel i810 @ 0xf8000000 64MB
Jun 19 19:09:01 naut kernel: [drm] Initialized i810 1.1.0 20000928 on minor 63
Jun 19 19:09:01 naut kernel: ISDN subsystem Rev: 1.114.6.11/1.94.6.1/1.140.6.4/1.85.6.4/1.21/1.5.6.3
Jun 19 19:09:01 naut kernel: SCSI subsystem driver Revision: 1.00
Jun 19 19:09:01 naut kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Jun 19 19:09:01 naut kernel:   Vendor: RICOH     Model: DVD/CDRW MP9060   Rev: 1.60
Jun 19 19:09:01 naut kernel:   Type:   CD-ROM                             ANSI SCSI revision: 02
Jun 19 19:09:01 naut kernel: ppa: Version 2.07 (for Linux 2.4.x)
Jun 19 19:09:01 naut kernel: WARNING - no ppa compatible devices found.
Jun 19 19:09:01 naut kernel:   As of 31/Aug/1998 Iomega started shipping parallel
Jun 19 19:09:01 naut kernel:   port ZIP drives with a different interface which is
Jun 19 19:09:01 naut kernel:   supported by the imm (ZIP Plus) driver. If the
Jun 19 19:09:01 naut kernel:   cable is marked with "AutoDetect", this is what has
Jun 19 19:09:01 naut kernel:   happened.
Jun 19 19:09:01 naut kernel: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Jun 19 19:09:01 naut kernel: sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Jun 19 19:09:01 naut kernel: Uniform CD-ROM driver Revision: 3.12
Jun 19 19:09:01 naut kernel: es1371: version v0.30 time 22:45:19 May 30 2001
Jun 19 19:09:01 naut kernel: PCI: Found IRQ 9 for device 01:0a.0
Jun 19 19:09:01 naut kernel: es1371: found chip, vendor id 0x1274 device id 0x5880 revision 0x02
Jun 19 19:09:01 naut kernel: es1371: found es1371 rev 2 at io 0xd400 irq 9
Jun 19 19:09:01 naut kernel: es1371: features: joystick 0x0
Jun 19 19:09:01 naut kernel: ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
Jun 19 19:09:01 naut kernel: usb.c: registered new driver usbdevfs
Jun 19 19:09:01 naut kernel: usb.c: registered new driver hub
Jun 19 19:09:01 naut kernel: PCI: Found IRQ 12 for device 00:1f.2
Jun 19 19:09:01 naut kernel: PCI: Setting latency timer of device 00:1f.2 to 64
Jun 19 19:09:01 naut kernel: uhci.c: USB UHCI at I/O 0xb400, IRQ 12
Jun 19 19:09:01 naut kernel: usb.c: new USB bus registered, assigned bus number 1
Jun 19 19:09:01 naut kernel: hub.c: USB hub found
Jun 19 19:09:01 naut kernel: hub.c: 2 ports detected
Jun 19 19:09:01 naut kernel: PCI: Found IRQ 9 for device 00:1f.4
Jun 19 19:09:01 naut kernel: PCI: The same IRQ used for device 01:0b.0
Jun 19 19:09:01 naut kernel: PCI: The same IRQ used for device 01:0b.1
Jun 19 19:09:01 naut kernel: PCI: Setting latency timer of device 00:1f.4 to 64
Jun 19 19:09:01 naut kernel: uhci.c: USB UHCI at I/O 0xb000, IRQ 9
Jun 19 19:09:01 naut kernel: usb.c: new USB bus registered, assigned bus number 2
Jun 19 19:09:01 naut kernel: hub.c: USB hub found
Jun 19 19:09:01 naut kernel: hub.c: 2 ports detected
Jun 19 19:09:01 naut kernel: uhci.c:  Linus Torvalds, Johannes Erdfelt, Randy Dunlap, Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber
Jun 19 19:09:01 naut kernel: uhci.c: USB Universal Host Controller Interface driver
Jun 19 19:09:01 naut kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jun 19 19:09:01 naut kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Jun 19 19:09:01 naut kernel: IP: routing cache hash table of 512 buckets, 4Kbytes
Jun 19 19:09:01 naut kernel: TCP: Hash tables configured (established 8192 bind 8192)
Jun 19 19:09:01 naut kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Jun 19 19:09:01 naut kernel: VFS: Mounted root (ext2 filesystem) readonly.
Jun 19 19:09:01 naut kernel: Freeing unused kernel memory: 180k freed
Jun 19 19:09:01 naut kernel: hub.c: USB new device connect on bus2/2, assigned device number 2
Jun 19 19:09:01 naut kernel: hub.c: USB hub found
Jun 19 19:09:01 naut kernel: hub.c: 4 ports detected
Jun 19 19:09:01 naut kernel: Adding Swap: 180012k swap-space (priority -1)
Jun 19 19:09:01 naut kernel: lirc_dev: IR Remote Control driver registered, at major 61 
Jun 19 19:09:01 naut kernel: i2c-core.o: driver i2c ir driver registered.
Jun 19 19:09:01 naut kernel: lirc_i2c: chip found @ 0x18 (Hauppauge IR)
Jun 19 19:09:01 naut kernel: bttv0: i2c attach [Hauppauge IR]
Jun 19 19:09:01 naut kernel: i2c-core.o: client [Hauppauge IR] registered to adapter [bt848 #0](pos. 2).
Jun 19 19:09:01 naut kernel: lirc_i2c: Huh? unknown i2c address (0x50)?

Francois Romieu

2001-06-21 19:23 UTC #1 lore raw

Jon Forsberg <[email protected]> �crit :

Quoted 6 lines

I have an Surecom EP-320X-S Ethernet adapter which apparently uses a Myson MTD-8xx chip. It works well with the "fealnx" driver (labeled "Myson MTD-8xx PCI Ethernet support" in kernel config) except for one thing:
After a while in use it stops working and prints
Jun 21 12:18:18 naut kernel: NETDEV WATCHDOG: eth0: transmit timed out

[...]

Could you give this a try please ?
It may crash.

drivers/net/fealnx.c +30 -7

@@ -418,7 +418,7 @@
 static struct net_device_stats *get_stats(struct net_device *dev);
 static int mii_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
 static int netdev_close(struct net_device *dev);
-
+static void reset_rx_descriptors(struct net_device *dev);
 
 void stop_nic_tx(long ioaddr, long crvalue)
 {

@@ -1121,14 +1121,13 @@
 {
 	struct netdev_private *np = dev->priv;
 	long ioaddr = dev->base_addr;
+	int i;
 
 	printk(KERN_WARNING "%s: Transmit timed out, status %8.8x,"
 	       " resetting...\n", dev->name, readl(ioaddr + ISR));
 
 #ifndef __alpha__
 	{
-		int i;
-
 		printk(KERN_DEBUG "  Rx ring %8.8x: ", (int) np->rx_ring);
 		for (i = 0; i < RX_RING_SIZE; i++)
 			printk(" %8.8x", (unsigned int) np->rx_ring[i].status);

@@ -1139,12 +1138,36 @@
 	}
 #endif
 
-	/* Perhaps we should reinitialize the hardware here.  Just trigger a
-	   Tx demand for now. */
+	dev->if_port = np->default_port;
+	/* Reinit. Gross */
+
+	/* Reset the chip's Tx and Rx processes. */
+	stop_nic_tx(ioaddr, 0);
+	reset_rx_descriptors(dev);
+
+	/* Disable interrupts by clearing the interrupt mask. */
+	writel(0x0000, ioaddr + IMR);
+
+	/* Reset the chip to erase previous misconfiguration. */
+	writel(0x00000001, ioaddr + BCR);
+	for (i = 0; i < 50; i++) {
+		readl(ioaddr + BCR);
+		rmb();
+	}
+
+	writel(virt_to_bus(np->cur_tx), ioaddr + TXLBA);
+	writel(virt_to_bus(np->cur_rx), ioaddr + RXLBA);
+
+	writel(np->bcrvalue, ioaddr + BCR);
+
+	writel(0, dev->base_addr + RXPDR);
+	set_rx_mode(dev);
+	/* Clear and Enable interrupts by setting the interrupt mask. */
+	writel(FBE | TUNF | CNTOVF | RBU | TI | RI, ioaddr + ISR);
+	writel(np->imrvalue, ioaddr + IMR);
+
 	writel(0, dev->base_addr + TXPDR);
-	dev->if_port = 0;
 
-	/* Stop and restart the chip's Tx processes . */
 	dev->trans_start = jiffies;
 	np->stats.tx_errors++;

Signature · 1 line

Ueimor

Jon Forsberg

author

2001-06-21 20:29 UTC #2 lore raw

In reply to Jon Forsberg

Quoted 11 lines · Francois Romieu

Jon Forsberg <[email protected]> écrit :
Quoted 6 lines
I have an Surecom EP-320X-S Ethernet adapter which apparently uses a Myson MTD-8xx chip. It works well with the "fealnx" driver (labeled "Myson MTD-8xx PCI Ethernet support" in kernel config) except for one thing:
After a while in use it stops working and prints
Jun 21 12:18:18 naut kernel: NETDEV WATCHDOG: eth0: transmit timed out
[...]
Could you give this a try please ?
It may crash.

Prints the same messages as before but continues working afterwards. No need for ifdown/ifup in other words. No crash so far.

--zzed

Francois Romieu

2001-06-22 08:33 UTC #3 lore raw

In reply to Jon Forsberg

Jon Forsberg <[email protected]> ecrit :
[...]

Quoted 2 lines

Prints the same messages as before but continues working afterwards. No need for ifdown/ifup in other words. No crash so far.

I'll polish and submit it to the maintainer next week then.

Signature · 1 line

Ueimor