Query about Tun/Tap Modules
Hello All,
I want to trap the ethernet packets from ethernet driver and then send it through a Bluetooth stack whose output will be in turn send through IP then TCP layers and vice-versa.(As a result inserting bluetooth stack between ethernet and IP layers) It is clear from the picture below.
|--------------------------------------------|
| TCP |
|--------------------------------------------|
|
bi directional Interface
|
|--------------------------------------------|
| IP |
|--------------------------------------------|
|bi directional Interface
|---------------------------------------------------------
| |
| Bluetooth |
| Stack |
| |
| |
| |
| |
|---------------------------------------------------------
bi directional Interface
|
|--------------------------------------------| | Ethernet | |--------------------------------------------|
For these message tapping I got this module called Tun/Tap at
http://vtun.sourceforge.net/tun
Some info about this is available at
http://www.linuxhq.com/kernel/v2.4/doc/networking/tuntap.txt.html also.
I compiled this module, made install, and insmod also. Till here no problem.
My queries are -
Q1 : Now I am not able to understand how to use this module for my above stated purpose.
If anybody has used this utility(Tun/tap) before , please let me know
how to get these ethernet packet going towards IP layer and IP packets going towards ethernet driver.
Q2. What can be other ways, not very complicated to solve my purpose instead of using Tun/Tap.
Q3. All the debug message are going to /var/log/messages, even if I send with the loglevel 1. How to get them on screen? How can I see the default console loglevel?
Hope to get an early reply.
Thanks a lot.
Shiva Raman Pandey
Research Associate-Computer Science R&D
Sasken Communication Technologies Limited.
Bangalore-India
Quoted 3 lines · Shiva Raman Pandey
Q2. What can be other ways, not very complicated to solve my purpose instead of using Tun/Tap.
The network block device can be used via loopback...
-Erik
--
Erik B. Andersen email: [email protected]
--This message was written using 73% post-consumer electrons--
"Erik Andersen wrote:"
Quoted 6 lines · Shiva Raman Pandey
Quoted 3 lines
Q2. What can be other ways, not very complicated to solve my purpose instead of using Tun/Tap.
The network block device can be used via loopback...
Not totally relaibly, however. It must deadlock when writing to a server on the same machine, because when we run out of memory we must free buffers by flushing pending writes on devices, which will send packets for the nbd out to loaclhost and to the local server, where they will take a buffer just prior to being written to disk ... and of course they won't succeed because we are out of memory.
I would like the algorithms that free buffers to avoid the device that caused the memory pressure. Since they can't do that, the next best thing is to avoid it some of the time, which they can do by avoiding everything randomly. Please add randomness under stress, people.
Peter
Quoted 5 lines · [email protected] said:
Q1 : Now I am not able to understand how to use this module for my above stated purpose.
If anybody has used this utility(Tun/tap) before , please let me
know how to get these ethernet packet going towards IP layer and IP packets going towards ethernet driver.
It's not clear how similar my use of TUN/TAP is to what you want, but UML uses TUN/TAP as one mechanism to network a virtual machine to the host, and it works quite well.
See tuntap_up() in
http://cvs.sourceforge.net/cgi-bin/viewcvs.cgi/user-mode-linux/tools/uml_net/uml_net.c?rev=1.10&content-type=text/vnd.viewcvs-markup
for setting up a TUN/TAP interface and tuntap_user_read() and tuntap_user_write() (which are both trivial)
http://cvs.sourceforge.net/cgi-bin/viewcvs.cgi/user-mode-linux/linux/arch/um/drivers/tuntap_user.c?rev=1.2&content-type=text/vnd.viewcvs-markup
for getting packets in and out of the interface.
Jeff