Skip to contentSkip to conversation

ide-scsi driver trouble in ac15

DISCUSSION safemode 3 participants 4 messages Sep 28, 2001

lore
Share & tools
lore

safemode

author
#0 lore raw

I'm not entirely sure if this is ac15's fault or the preempt patch acting up. But this is very ide-scsi centric so i'm leaning towards ac15. I burned a cd using my ide writer and it worked fine. Then i went to burn another and the drive went into an infinite reset loop. like this.
SCSI bus is being reset for host 0 channel 0.
scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.

reloading the modules does nothing but report this error.
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset. SCSI bus is being reset for host 0 channel 0.

Even though the modules were removed, the drive led is still blinking like it was writing. If anyone needs some more info i'll try and get it. the cdr did detect and work correctly at boot.

hardware:
Promise ide controller :
PDC20262: chipset revision 1
PDC20262: not 100% native mode: will probe irqs later
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
CDR:
hde: CREATIVE CD-RW RW8438E, ATAPI CD/DVD-ROM drive
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: CREATIVE Model: CD-RW RW8438E Rev: FC03
Type: CD-ROM ANSI SCSI revision: 02
software:

    Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
    linux-2.4.9-ac15-preempt-fix
#1 lore raw
Quoted 23 lines · safemode

I'm not entirely sure if this is ac15's fault or the preempt patch acting up. But this is very ide-scsi centric so i'm leaning towards ac15. I burned a cd using my ide writer and it worked fine. Then i went to burn another and the drive went into an infinite reset loop. like this.
SCSI bus is being reset for host 0 channel 0.
scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.

reloading the modules does nothing but report this error.
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset. SCSI bus is being reset for host 0 channel 0.

Even though the modules were removed, the drive led is still blinking like it was writing. If anyone needs some more info i'll try and get it. the cdr did detect and work correctly at boot.

hardware:
Promise ide controller :
PDC20262: chipset revision 1
PDC20262: not 100% native mode: will probe irqs later
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
CDR:
hde: CREATIVE CD-RW RW8438E, ATAPI CD/DVD-ROM drive
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices

(quoted diff) +0 -0
 	Vendor: CREATIVE  Model:  CD-RW RW8438E    Rev: FC03
 	Type:   CD-ROM                             ANSI SCSI revision: 02
Quoted 4 lines

software:
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling linux-2.4.9-ac15-preempt-fix

It also happened to me with ac10, ide-scsi, CD-RW is a Samsung 8x, and I was writing a audio cd, when it finished writing the track 8 of 18 it entered the loop, since then I couldn't eject the cd, neither eject /dev/hdb, nor cdrecord -eject, nor the eject button, I had to reboot.

My system is a 2x200mmx smp all ide.

Signature · 2 lines
Jorge Nerin
<[email protected]>
#2 lore raw

In article <[email protected]> [email protected] wrote:

[ ide-scsi problens ]

Quoted 7 lines

It also happened to me with ac10, ide-scsi, CD-RW is a Samsung 8x, and = I=20
was writing a audio cd, when it finished writing the track 8 of 18 it=20 entered the loop, since then I couldn't eject the cd, neither eject=20 /dev/hdb, nor cdrecord -eject, nor the eject button, I had to reboot.

My system is a 2x200mmx smp all ide.

Don't see it on a P-II-400 (Dell Dimension 400). The Yamaha on-board sound doesn't work, but it never did, it just thinks it is, sound apps work fine but never produce output.

I do note that the sound modules noted in modules.conf didn't load and need to be hand loaded...

Signature · 4 lines
bill davidsen <[email protected]>
 "If I were a diplomat, in the best case I'd go hungry.  In the worst
  case, people would die."
		-- Robert Lipe
author
#3 lore raw
In reply to safemode
Quoted 33 lines · Jorge Nerín
Quoted 29 lines · safemode

I'm not entirely sure if this is ac15's fault or the preempt patch acting up. But this is very ide-scsi centric so i'm leaning towards ac15. I burned a cd using my ide writer and it worked fine. Then i went to burn another and the drive went into an infinite reset loop. like this.
SCSI bus is being reset for host 0 channel 0.
scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.

reloading the modules does nothing but report this error.
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset. SCSI bus is being reset for host 0 channel 0.

Even though the modules were removed, the drive led is still blinking like it was writing. If anyone needs some more info i'll try and get it. the cdr did detect and work correctly at boot.

hardware:
Promise ide controller :
PDC20262: chipset revision 1
PDC20262: not 100% native mode: will probe irqs later
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
CDR:
hde: CREATIVE CD-RW RW8438E, ATAPI CD/DVD-ROM drive
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices

(quoted diff) +0 -0
 	Vendor: CREATIVE  Model:  CD-RW RW8438E    Rev: FC03
 	Type:   CD-ROM                             ANSI SCSI revision: 02

software:

Quoted 2 lines
   Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg

Schilling linux-2.4.9-ac15-preempt-fix

Quoted 6 lines

It also happened to me with ac10, ide-scsi, CD-RW is a Samsung 8x, and I was writing a audio cd, when it finished writing the track 8 of 18 it entered the loop, since then I couldn't eject the cd, neither eject /dev/hdb, nor cdrecord -eject, nor the eject button, I had to reboot.

My system is a 2x200mmx smp all ide.

Seems to be an interesting coincidence, i had just written an audio cd and was writing another when it happened. Only it happened to me when just beginning the cd. Had to reboot. The cd was fine, it never actually got to writing, so i used it after i had rebooted the system and it worked fine.