2.4.9-ac10 IDE access slows as uptime increases
I've been noticing this for months, and thought I was crazy. But I
just verified it.
I ran a program that's a GUI app/front-end to a data base, on the
local drives. It took seconds to access a record.
Rebooted. Ran the same thing again. The program accessed records
almost instantly.
I get faster response time from the 2.2.20-pre2 systems over 100MBs
NFS than I do on the 2.4 system after it has been running for a few hours. NFS is slow enough, usually use ssh and run the program on the DB system. (Only use a local copy when testing.)
Use the system mostly to compile, debug and test.
processor : 0vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 10
cpu MHz : 999.743
cache size : 256 KBfdiv_bug : nohlt_bug : nof00f_bug : nocoma_bug : no
fpu : yesfpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1992.29
total: used: free: shared: buffers: cached:
Mem: 1053401088 1002246144 51154944 10092544 51945472 798220288 Swap: 2147467264 4096 2147463168 MemTotal: 1028712 kB MemFree: 49956 kB MemShared: 9856 kB Buffers: 50728 kB Cached: 779508 kB SwapCached: 4 kB Active: 505116 kB Inact_dirty: 76400 kB Inact_clean: 258580 kB Inact_target: 352 kB HighTotal: 130992 kB HighFree: 7256 kB LowTotal: 897720 kB LowFree: 42700 kB SwapTotal: 2097136 kB SwapFree: 2097132 kB
Personalities : [raid1]read_ahead 1024 sectors
md0 : active raid1 ide/host0/bus1/target1/lun0/part2[1] ide/host0/bus0/target0/lun0/part2[0]
6291840 blocks [2/2] [UU]
md1 : active raid1 ide/host0/bus1/target1/lun0/part3[1] ide/host0/bus0/target0/lun0/part3[0]
51661952 blocks [2/2] [UU]unused devices: <none>
8:32pm up 1:42, 23 users, load average: 2.87, 3.07, 2.77
All those users are me, logged into different xterms, most of which are not being used during the uptime.
XFree86 4.0.3. Using nVidia drivers. I really don't remember if the
problem was there when I was using an Athlon similarly configured except for a Voodoo3 and 3/4 the RAM. Had so many problems with the Athlon, I gave it to a co-worker who doesn't use their box as heavily as I do. They haven't had any problems with the Athlon.
I seem to remember this as a problem on the Athlon, too, but won't
swear to it because there were too many other things going on and this is the first time I actually checked to see if the slowdown was real.
Also have VMware modules loaded all the time. Don't always use it
every day though, and still see the slowdown. The system is rebooted each morning right now, most of the time (unless I just forget). The slowdown doesn't just affect the data base program. Its just really noticeable there.
Config attached. Any ideas how to check this out further?
Quoted 4 lines
I've been noticing this for months, and thought I was crazy. But I
just verified it.
I ran a program that's a GUI app/front-end to a data base, on the
local drives. It took seconds to access a record.
Is the data base doing I/O directly to a block device and not using O_DIRECT for one question
Second question is what is in your IDE logs. The IDE layer will change down speeds when it hits a repeated problem (eg a DMA timeout) so if need be will switch back to PIO or to MWDMA.
DB uses regular file system (ext3) and mmap.
Nothing in logs from IDE. Only thing there unknown to me from kernel:
cmpci: dma timed out??
That's from the sound driver, apparently. No idea what it means.
By the way, would hdparm -i report the change? If so, they're all
still UDMA.
I'm going to try removing the IDE to SCSI stuff that I installed to
try and get a USB CDRW drive working. Never did, and have not used any time to pursue it (always timed out on access, now not even in devfs for some reason). No idea if that's relevant, either, but it looks like something I botched.
The last message was so long that this may have been missed: it's not
just the DB that shows the slowdown. It's general. It's just really obvious with the DB due to visual feedback. Who would notice if gcc-3 took an extra 20 minutes to compile something ;( (I haven't really timed it. I noticed gcc gets slower, but not timed it to see how much, so its subjective.)
This may be irrelevant, but here's meminfo this morning:
total: used: free: shared: buffers: cached:
Mem: 1053401088 887148544 166252544 65536 242728960 552976384 Swap: 2147467264 74866688 2072600576 MemTotal: 1028712 kB MemFree: 162356 kB MemShared: 64 kB Buffers: 237040 kB Cached: 478604 kB SwapCached: 61412 kB Active: 421960 kB Inact_dirty: 352208 kB Inact_clean: 2952 kB Inact_target: 260 kB HighTotal: 130992 kB HighFree: 2036 kB LowTotal: 897720 kB LowFree: 160320 kB SwapTotal: 2097136 kB SwapFree: 2024024 kB
Quoted 9 lines · Alan Cox
Quoted 2 lines
I ran a program that's a GUI app/front-end to a data base, on the
local drives. It took seconds to access a record.Is the data base doing I/O directly to a block device and not using
O_DIRECTfor one questionSecond question is what is in your IDE logs. The IDE layer will change down speeds when it hits a repeated problem (eg a DMA timeout) so if need be will switch back to PIO or to MWDMA.
Quoted 3 lines · * Alan Cox ([email protected]) wrote:
Second question is what is in your IDE logs. The IDE layer will change down speeds when it hits a repeated problem (eg a DMA timeout) so if need be will switch back to PIO or to MWDMA.
I have what sounds like a similar problem - assuming it is a problem with the IDE layer dropping the speed - except mine is with my CD or DVD drive. They run a lot slower under the 2.4.x kernels than under 2.2.19 (looking at 2-3megs/s under 2.4.x, 5-7megs/s under 2.2.19).
Also when using 2.4.x, the kernel has a habit of disabling DMA and performance plummets. Yet it is fine with 2.2.19.
Is this a related issue? Is there a fix for this?
Steve Maughan
Quoted 9 lines
I have what sounds like a similar problem - assuming it is a problem with the IDE layer dropping the speed - except mine is with my CD or DVD drive. They run a lot slower under the 2.4.x kernels than under 2.2.19 (looking at 2-3megs/s under 2.4.x, 5-7megs/s under 2.2.19).
Also when using 2.4.x, the kernel has a habit of disabling DMA and performance plummets. Yet it is fine with 2.2.19.
Is this a related issue? Is there a fix for this?
That sounds different, Talk to Andre I guess
Quoted 2 lines · Phil Blecker
I'm going to try removing the IDE to SCSI stuff that I installed to
try and get a USB CDRW drive working.
That seems to have worked. Haven't used the system as heavily today
as usual, but the slowdown didn't happen. Makes no sense to me, but what do I know?