Skip to contentSkip to conversation

Tyan Tiger MP AMD760 chipset support

DISCUSSION Willem Riede 5 participants 6 messages Oct 7, 2001 – Oct 8, 2001

lore
Share & tools
lore
#0 lore raw

Since Alan Cox wrote months ago:

Quoted 1 line

2.4.7ac should be up to date on it

with reference to AMD760 (IDE?) support on a Tyan K7 Thunder, I was somewhat surprised to find the chipset:

AMD-762 North bridge & AMD-766 South bridge Winbond W83627HF Super I/O ASIC Winbond W83782D hardware monitoring ASIC

only partly recognized by my 2.4.9ac18 based kernel. One problem is that the temperature sensors are not detected (I'm reluctant to torture my system if I can't watch out for it overheating).

Does anyone know the AMD760 support status? Any pointers for (experimental) patches?

Here is the lspci -vvv output:

00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700c (rev
11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-

	Latency: 64
	Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
	Region 1: Memory at e8006000 (32-bit, prefetchable) [size=4K]
	Region 2: I/O ports at 10a0 [disabled] [size=4]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=15 SBA+ 64bit- FW+ Rate=x1,x2
		Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x1

00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700d (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

	Latency: 99
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: e8100000-e81fffff
	Prefetchable memory behind bridge: f0000000-f7ffffff
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-765 [Viper] ISA (rev
02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-765 [Viper] IDE (rev 01) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

	Latency: 64
	Region 4: I/O ports at f000 [size=16]

00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-765 [Viper] ACPI (rev 01)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

00:07.4 USB Controller: Advanced Micro Devices [AMD] AMD-765 [Viper] USB (rev 07) (prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

	Latency: 16 (20000ns max)
	Interrupt: pin D routed to IRQ 11
	Region 0: Memory at 000dc000 (32-bit, non-prefetchable) [size=4K]

00:0b.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 01) (prog-if 85)
Subsystem: Promise Technology, Inc. 20268
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

	Latency: 64 (1000ns min, 4500ns max), cache line size 10
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 10b8 [size=8]
	Region 1: I/O ports at 10b0 [size=4]
	Region 2: I/O ports at 10a8 [size=8]
	Region 3: I/O ports at 10a4 [size=4]
	Region 4: I/O ports at 1090 [size=16]
	Region 5: Memory at e8000000 (32-bit, non-prefetchable) [size=16K]
	Expansion ROM at <unassigned> [disabled] [size=16K]
	Capabilities: [60] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 78)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC
Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 2500ns max), cache line size 10
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1000 [size=128]
Region 1: Memory at e8005000 (32-bit, non-prefetchable) [size=128] Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5144 (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 008a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

	Latency: 66 (2000ns min), cache line size 10
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at 2000 [size=256]
	Region 2: Memory at e8100000 (32-bit, non-prefetchable) [size=512K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [58] AGP version 2.0
		Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=15 SBA+ AGP+ 64bit- FW- Rate=x1
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Thanks. Willem Riede.

#1 lore raw
Quoted 7 lines · Willem Riede

with reference to AMD760 (IDE?) support on a Tyan K7 Thunder, I was somewhat surprised to find the chipset:

AMD-762 North bridge & AMD-766 South bridge Winbond W83627HF Super I/O ASIC Winbond W83782D hardware monitoring ASIC

Quoted 7 lines

only partly recognized by my 2.4.9ac18 based kernel. One problem is that the temperature sensors are not detected (I'm reluctant to torture my system if I can't watch out for it overheating).

Does anyone know the AMD760 support status? Any pointers for (experimental) patches?

Look into the lm_sensors patch; it supports many such hardware monitoring chips, and I believe that yours is one of them.

Signature · 8 lines
-Steven
In a time of universal deceit, telling the truth is a revolutionary act.
			-- George Orwell
Freedom is slavery. Ignorance is strength. War is peace.
			-- George Orwell
Those that would give up a necessary freedom for temporary safety
deserver neither freedom nor safety.
			-- Ben Franklin
#2 lore raw
In reply to Willem Riede

That's not the issue, I'm not that ignorant. sensors-detect just doesn't find anything!

Willem Riede.
-------------

Quoted 22 lines · On 2001.10.07 15:12 Steven Walter wrote:
Quoted 7 lines · Willem Riede

with reference to AMD760 (IDE?) support on a Tyan K7 Thunder, I was somewhat surprised to find the chipset:

AMD-762 North bridge & AMD-766 South bridge Winbond W83627HF Super I/O ASIC Winbond W83782D hardware monitoring ASIC

Quoted 7 lines

only partly recognized by my 2.4.9ac18 based kernel. One problem is that the temperature sensors are not detected (I'm reluctant to torture my system if I can't watch out for it overheating).

Does anyone know the AMD760 support status? Any pointers for (experimental) patches?

Look into the lm_sensors patch; it supports many such hardware monitoring chips, and I believe that yours is one of them.

Signature · 1 line
-Steven
#3 lore raw
In reply to Willem Riede
Quoted 2 lines · Willem Riede

That's not the issue, I'm not that ignorant. sensors-detect just doesn't find anything!

Upgrade to the cvs version of lm_sensors and the i2c drivers.

I can with these modules detect the eeprom, the AMD756 and the winbond W83782D.

But, however, inserting the winbond driver locks the computer hard.

Signature · 1 line
carpe noctem
#4 lore raw
Quoted 3 lines · Roy-Magne Mo

I can with these modules detect the eeprom, the AMD756 and the winbond W83782D.
But, however, inserting the winbond driver locks the computer hard.

It's a bug in the lm_sensors winbond driver. There's been a patch posted in the bugtracker but afaik hasn't been integrated into cvs yet...

-Dan

Signature · 1 line
[-] Omae no subete no kichi wa ore no mono da. [-]
#5 lore raw
In reply to Willem Riede
Quoted 5 lines · Roy-Magne Mo
Quoted 2 lines · Willem Riede

That's not the issue, I'm not that ignorant. sensors-detect just doesn't find anything!

Quoted 7 lines

Upgrade to the cvs version of lm_sensors and the i2c drivers.

I can with these modules detect the eeprom, the AMD756 and the winbond W83782D.

But, however, inserting the winbond driver locks the computer hard.

I've had the same problem with two Tyan Thunder K7 motherboards, inserting the winbond driver locks the computer hard. However booting with the "noapic" option solves this. Ideas anyone ? Are the AMD erratas publicly available ?

Regards,

Signature · 4 lines
  Steffen Persvold   | Scalable Linux Systems |   Try out the world's best   
 mailto:[email protected]  |  http://www.scali.com  | performing MPI implementation:
Tel: (+47) 2262 8950 |   Olaf Helsets vei 6   |      - ScaMPI 1.12.2 -         
Fax: (+47) 2262 8951 |   N0621 Oslo, NORWAY   | >300MBytes/s and <4uS latency