Skip to contentSkip to conversation

IDE Hot-Swap, does it work?

DISCUSSION Mike Panetta 3 participants 6 messages Oct 11, 2001 – Oct 13, 2001

lore
Share & tools
lore
#0 lore raw

Is IDE Hot-Swap supported in any fashion in linux? If so what are the recommended controllers and enclosures to use? Are there any standards for IDE enclosures like there are for SCSI (SAF-TE SES)?

In addition, I have noticed that there is an hdparm command that will allow me to rescan an interface, but I cannot get it to do anything other than lock my machine up with the promise card I have. Anyone have insight into this?

Thanks,
Mike

Signature · 3 lines
----- End forwarded message -----

-- 
#1 lore raw

Re: IDE Hot-Swap, does it work?, Conspiracy is afoot!

Ok, I have played with this a bit since I have recieved no real respose other than one other person having the same question, here is what I have found out...

I have a piece of hardware that does have hot-swap IDE chassis on it, so atleast the IDE bus xcvers should be able to handle the swapping, as the connection to the drive is disabled before the can comes all the way out of the slot.

- I can remove a drive while the system is on and I have a software raid 5 on the 4 drives, everything is ok after about 2 minutes the system recovers and the software raid fails the drive I removed. This makes sense.
- After a few minutes I replace the drive I had just failed by removing it, and I try to readd it to the system via raidhotadd. One of 2 things happens in this instance, depending on what kernel I have loaded.
- If I have kernel 2.4.2-2 loaded (a stock redhat 7.1 kernel), the drive reappears, and can be added back to the raid (and is added back).
- If I am running kernel 2.4.10 or any later (AC or non) the machine fails to ever be able to read from the disk again. I cannot readd the disk to the arry, nor can I fdisk it (or access it in any other way).
- None of this solves the adding of a drive to the system where there was none before boot... I tried the hdparm -R stuff but its useless and hangs my box no matter what I give it as paramaters. This of course may be because I do not know how to use it very well...

If anyone can help it would be greatly appreciated. I am really beginning to believe that IDE will never be as capable as SCSI in this reguard, atleast not in linux, espically as any (even if it was broken) support that used to be in the kernel has disappeared. Please someone convince me otherwise! Atleast point me in the correct direction as to what in the kernel would have to be changed to make this work...

Thanks,
Mike

#2 lore raw

Re: IDE Hot-Swap, does it work?, Conspiracy is afoot!

In reply to Mike Panetta

I've done this with my IDE cdrom in my laptop. It's hot swappable and I asked about this at one time. In the source package for hdparm (i know it's in the debian's source package) there's a script for hot add/remove of ide devices. there's a nice warning attached about ide hotswap

Quoted 48 lines

Ok, I have played with this a bit since I have recieved no real respose other than one other person having the same question, here is what I have found out...

I have a piece of hardware that does have hot-swap IDE chassis on it, so atleast the IDE bus xcvers should be able to handle the swapping, as the connection to the drive is disabled before the can comes all the way out of the slot.

- I can remove a drive while the system is on and I have a software raid 5 on the 4 drives, everything is ok after about 2 minutes the system recovers and the software raid fails the drive I removed. This makes sense.
- After a few minutes I replace the drive I had just failed by removing it, and I try to readd it to the system via raidhotadd. One of 2 things happens in this instance, depending on what kernel I have loaded.
- If I have kernel 2.4.2-2 loaded (a stock redhat 7.1 kernel), the drive reappears, and can be added back to the raid (and is added back).
- If I am running kernel 2.4.10 or any later (AC or non) the machine fails to ever be able to read from the disk again. I cannot readd the disk to the arry, nor can I fdisk it (or access it in any other way).
- None of this solves the adding of a drive to the system where there was none before boot... I tried the hdparm -R stuff but its useless and hangs my box no matter what I give it as paramaters. This of course may be because I do not know how to use it very well...

If anyone can help it would be greatly appreciated. I am really beginning to believe that IDE will never be as capable as SCSI in this reguard, atleast not in linux, espically as any (even if it was broken) support that used to be in the kernel has disappeared. Please someone convince me otherwise! Atleast point me in the correct direction as to what in the kernel would have to be changed to make this work...

Thanks,
Mike

Signature · 5 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/
Signature · 1 line
 Lab tests show that use of micro$oft causes cancer in lab animals
#3 lore raw

Re: IDE Hot-Swap, does it work?, Conspiracy is afoot! (more questions)

I've been too asked this question two times in the list, and i haven't received any useful answer.

Wakko, could you tell me in detail how to use hdparm -R and -U, because i couldn't get it work. Does it (or shoudl it) work for harddisks too?

What chipset/hardware supports ide-hot-swap, and which of these are supported in linux?
Under The Other Operating System 2000 i have seen this working on a few machines for example on an asus cusl2 mobo, so that chipset (i think intel 815e) at least can got to do this job.

Please someone with more knowledge enlighten me, beaces i really hate rebooting just to remove or add a harddisk.

Quoted 61 lines · Wakko Warner

I've done this with my IDE cdrom in my laptop. It's hot swappable and I asked about this at one time. In the source package for hdparm (i know it's in the debian's source package) there's a script for hot add/remove of ide devices. there's a nice warning attached about ide hotswap

Quoted 42 lines

Ok, I have played with this a bit since I have recieved no real respose other than one other person having the same question, here is what I have found out...

I have a piece of hardware that does have hot-swap IDE chassis on it, so atleast the IDE bus xcvers should be able to handle the swapping, as the connection to the drive is disabled before the can comes all the way out of the slot.

- I can remove a drive while the system is on and I have a software raid 5 on the 4 drives, everything is ok after about 2 minutes the system recovers and the software raid fails the drive I removed. This makes sense.
- After a few minutes I replace the drive I had just failed by removing it, and I try to readd it to the system via raidhotadd. One of 2 things happens in this instance, depending on what kernel I have loaded.
- If I have kernel 2.4.2-2 loaded (a stock redhat 7.1 kernel), the drive reappears, and can be added back to the raid (and is added back).
- If I am running kernel 2.4.10 or any later (AC or non) the machine fails to ever be able to read from the disk again. I cannot readd the disk to the arry, nor can I fdisk it (or access it in any other way).
- None of this solves the adding of a drive to the system where there was none before boot... I tried the hdparm -R stuff but its useless and hangs my box no matter what I give it as paramaters. This of course may be because I do not know how to use it very well...

If anyone can help it would be greatly appreciated. I am really beginning to believe that IDE will never be as capable as SCSI in this reguard, atleast not in linux, espically as any (even if it was broken) support that used to be in the kernel has disappeared. Please someone convince me otherwise! Atleast point me in the correct direction as to what in the kernel would have to be changed to make this work...

Thanks,
Mike

Quoted 6 lines

--
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

--
Lab tests show that use of micro$oft causes cancer in lab animals
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Signature · 1 line
Pozsar Balazs.
#4 lore raw

Re: IDE Hot-Swap, does it work?, Conspiracy is afoot! (more questions)

In reply to Wakko Warner
Quoted 7 lines · Pozsar Balazs

I've been too asked this question two times in the list, and i haven't received any useful answer.

Wakko, could you tell me in detail how to use hdparm -R and -U, because i couldn't get it work. Does it (or shoudl it) work for harddisks too?

I have been using this basic command form, but I think it may be incorrect:

hdparm -R [io addr ix hex] 0|[ctrl addr in hex] 0|[irq] /dev/hd?

if this is the wrong way to do it please tell me.

I am wondering how hard it would be to change the ioctl so that it accepts an index, or nothing (it just scans) instead of requiring the (sometimes hard to find) IO addres and such. I know that the lagacy IO addresses never change, but the PCI ones can be anything. Or maybe this just does not work with PCI IDE cards at all? I do not know.

Thanks,
Mike

#5 lore raw

Re: IDE Hot-Swap, does it work?, Conspiracy is afoot! (more questions)

In reply to Wakko Warner
Quoted 2 lines · Pozsar Balazs

Wakko, could you tell me in detail how to use hdparm -R and -U, because i couldn't get it work. Does it (or shoudl it) work for harddisks too?

I'm not sure if it supports hdds or not, As far as I can see, it basically rescans for the device you're doing. I attach the contrib script (comes in hdparm's source tree but not generally included

Quoted 5 lines

What chipset/hardware supports ide-hot-swap, and which of these are supported in linux?
Under The Other Operating System 2000 i have seen this working on a few machines for example on an asus cusl2 mobo, so that chipset (i think intel 815e) at least can got to do this job.

I think it would work on all ide chipsets, but i'm not sure. I have hot plugged IDE into standard systems and hdds not designed for it. You do run a risk of hardware damage which I has never happened for me (but could happen to me next time I try or it could happen to you. Be warned). For this, I've had a system who's / is not an ide disk (I have a machine mounting / over nfs) and I load/unload ide modules.

I'd like to see support for this similar to /proc/scsi/scsi to rescan

Signature · 1 line
 Lab tests show that use of micro$oft causes cancer in lab animals

#!/bin/sh

HDPARM=/sbin/hdparm
MAX_IDE_NR=1

IDE_IO_0=0x1f0
IDE_IO_1=0x170

USE_IDE_DEV_0=/dev/hdc
USE_IDE_DEV_1=/dev/hda

usage () {
	if [ $# -gt 0 ]; then
		echo $* >&2
		echo
	fi

	echo "usage: $0 ide-channel-nr [off|on|rescan]" 2>&1
	exit 1
}

IDE_NR=$1
MODE=$2

do_register=0
do_unregister=0

if [ ! "$IDE_NR" ] || [ $IDE_NR -lt 0 ] || [ $IDE_NR -gt $MAX_IDE_NR ]; then
usage "Unrecognized IDE-channel number"
fi

case "$MODE" in
on ) do_register=1 ;;
off ) do_unregister=1 ;;
rescan ) do_unregister=1; do_register=1 ;;
* ) usage "Unrecognized command" ;;
esac

eval "IDE_IO=\$IDE_IO_$IDE_NR"
eval "USE_IDE_DEV=\$USE_IDE_DEV_$IDE_NR"

[ $do_unregister -eq 1 ] && eval "$HDPARM -U $IDE_NR $USE_IDE_DEV > /dev/null" [ $do_register -eq 1 ] && eval "$HDPARM -R $IDE_IO 0 0 $USE_IDE_DEV > /dev/null"