Skip to contentSkip to conversation

problems with I/O performance with 2.4.12-ac3

DISCUSSION Andrei Lahun 2 participants 4 messages Oct 19, 2001 – Oct 20, 2001

lore
Share & tools
lore
#0 lore raw

hello.

I did a bonnie++ tests with 2.4.13-pre3(+aa vm)
and 2.4.12-ac3(+Rick patch).
And i found that ac kernel have a big problems here. With linux kernel i got 22 Mb/c for read 19 for write and with ac 12 for read and 11 for write (both with ext2) If i used ext3 with ac kernel results little bit better. What is the reason for such regression in ac kernel ? And yes of course i had udma for both test.

Andrei.

#1 lore raw
Quoted 11 lines · Andrei Lahun

hello.

I did a bonnie++ tests with 2.4.13-pre3(+aa vm)
and 2.4.12-ac3(+Rick patch).
And i found that ac kernel have a big problems here. With linux kernel i got 22 Mb/c for read 19 for write and with ac 12 for read and 11 for write (both with ext2) If i used ext3 with ac kernel results little bit better. What is the reason for such regression in ac kernel ? And yes of course i had udma for both test.

Quoted 1 line

Andrei.

You should give ide and drive chipset info. This is not a problem seen by everyone using the ac3 kernel. Mine for instance run just fine. What settings did you use with bonnie++? all of this is required info if someone wanted to look and see why you are getting those numbers.

#2 lore raw
In reply to Andrei Lahun
Quoted 6 lines · On Fri, 19 Oct 2001 09:27:35 -0400 safemode <[email protected]> wrote:

You should give ide and drive chipset info. This is not a problem seen by everyone using the ac3 kernel. Mine for instance run just fine. What settings did you use with bonnie++? all of this is required info if someone wanted to look and see why you are getting those numbers.

My chipset is VIA apollo 133-A ( old shirt).
I have run bonnie++ just like bonnie -s 256 , and i have 128 MB of memory,
disk is MAXTOR 52049H4.With old kernels i always had results something like i have with 2.4.13-pre now . And i have read one post in lkml about 2 times less write output with 2.4.13 -pre comparing with ac, mine result are opposite.

#3 lore raw
In reply to Andrei Lahun
Quoted 8 lines · Andrei Lahun

On Fri, 19 Oct 2001 09:27:35 -0400

Quoted 4 lines · safemode

You should give ide and drive chipset info. This is not a problem seen by everyone using the ac3 kernel. Mine for instance run just fine. What settings did you use with bonnie++? all of this is required info if someone wanted to look and see why you are getting those numbers.

Quoted 6 lines

My chipset is VIA apollo 133-A ( old shirt).
I have run bonnie++ just like bonnie -s 256 , and i have 128 MB of memory, disk is MAXTOR 52049H4.With old kernels i always had results something like i have with 2.4.13-pre now . And i have read one post in lkml about 2 times less write output with 2.4.13 -pre comparing with ac, mine result are opposite.

2.4.12-ac3-preempt-hogstop (no vm patches after the hogstop patch of a
couple days ago).
PDC20262: chipset revision 1
(my drive on the VIA vt82c686a (rev 22) is too full to run the test) Maxtor 32049H2, ATA DISK drive
All tests were done on this drive.

(not clean boot)

test results (bonnie++) no extra arguments.
Version 1.02 ------Sequential Output------ --Sequential Input-
--Random-

                    -Per Chr- --Block-- -Rewrite- -Per Chr- --Block-- 

--Seeks--
Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP /sec
%CP
psuedomode 1504M 6668 95 27108 39 5429 8 6217 82 22005 11 76.9
0

                    ------Sequential Create------ --------Random 
Create--------
                    -Create-- --Read--- -Delete-- -Create-- --Read--- 
-Delete--
              files  /sec %CP  /sec %CP  /sec %CP  /sec %CP  /sec %CP  /sec 
%CP
                 16  1501  97 +++++ +++ +++++ +++  1548  99 +++++ +++  4056  

99 psuedomode,1504M,6668,95,27108,39,5429,8,6217,82,22005,11,76.9,0,16,1501,97,+++++,+++,+++++,+++,1548,99,+++++,+++,4056,99

hdparm results
Timing buffered disk reads: 64 MB in 2.26 seconds = 28.32 MB/sec
Timing buffer-cache reads: 128 MB in 1.00 seconds =128.00 MB/sec
(run in that order)

dbench results (./dbench 32)
Throughput 47.3829 MB/sec (NB=59.2286 MB/sec 473.829 MBit/sec)