2.4.10ac10, cdrecord 1.9-6, Mitsumi CR-4804TE: lock up burning too large image
When (accidentally) trying to burn ~670MB onto a 74" cdr disk, I experienced a complete lock up.
It went to 99% (as one would expect), and then drive began giving weird sounds - as if it was moving the head from start to end over and over. After a short while, the whole system locked up, no mouse, keyboard, caps lock, ctrl-alt-del, alt-sysrq-{s,u,b}.
It used to give a nice error when disk size was exceeded with 2.2.18pre19 and a tad older cdrecord (1.9-something (1.10-4 failed on 2.2 BTW, giving error on mmapping /dev/null)).
I assume this is a kernel thing...
BTW: Also the cd audio ripping speed has dropped from ~8x to ~1x with both my cdrw and cd drive. The drop took place before upgrading from 2.2 to 2.4. I am and was using scsi-emulation for both drives. I tried going back to older cdparanoia, but it didn't help. Before I try to binary search what has changed, does anybody have any ideas on what to try?
------------------------------------------------------------------------
kernel 2.4.10-ac10 SMP
cdrecord 1.9-6
dmesg:
scsi : 0 hosts left.
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MITSUMI Model: CR-4804TE Rev: 2.4C
Type: CD-ROM ANSI SCSI revision: 02
APIC error on CPU0: 08(02)
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
hdparm /dev/hdd:
/dev/hdd:
HDIO_GET_MULTCOUNT failed: Input/output error
I/O support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 1 (on) keepsettings = 0 (off)
HDIO_GET_NOWERR failed: Input/output error
readonly = 0 (off)
BLKRAGET failed: Input/output error
HDIO_GETGEO failed: Invalid argument
cdrecord -scanbus:
0,1,0 1) 'MITSUMI ' 'CR-4804TE ' '2.4C' Removable CD-ROM
kernel messages before the lockup:
Oct 20 20:35:53 kernel: scsi : aborting command due to timeout : pid 155966,
@+scsi0, channel 0, id 1, lun 0 0x2a 00 00 05 48 9e 00 00 1f 00
Oct 20 20:35:53 kernel: hdd: timeout waiting for DMA
Oct 20 20:35:53 kernel: ide_dmaproc: chipset supported ide_dma_timeout func
@+only: 14
Oct 20 20:35:54 kernel: hdd: status timeout: status=0xd0 { Busy }
Oct 20 20:35:54 kernel: hdd: drive not ready for command
Oct 20 20:36:28 kernel: hdd: ATAPI reset timed-out, status=0xd0 <halted at this point>
-- v --
In article <[email protected]> [email protected] wrote:
| When (accidentally) trying to burn ~670MB onto a 74" cdr disk, I experienced
| a complete lock up.
|
| It went to 99% (as one would expect), and then drive began giving weird
| sounds - as if it was moving the head from start to end over and over. After
| a short while, the whole system locked up, no mouse, keyboard, caps lock,
| ctrl-alt-del, alt-sysrq-{s,u,b}.
|
| It used to give a nice error when disk size was exceeded with 2.2.18pre19
| and a tad older cdrecord (1.9-something (1.10-4 failed on 2.2 BTW, giving
| error on mmapping /dev/null)).
|
| I assume this is a kernel thing... You are probably correct, but you might try running as a user other
than root, with proper permissions on the device. cdwrite tries to run with realtime priority, and I don't know just how tightly a realtime process could lock the systems if it gets its knickers in a twist.
You might also try software watchdog, I would expect it to reboot if
the kernel is up but the RT process is looping, such as waiting for a status to change or some such.
Signature · 3 lines
bill davidsen <[email protected]> His first management concern is not solving the problem, but covering his ass. If he lived in the middle ages he'd wear his codpiece backward.