Skip to contentSkip to conversation

VIA 686b Bug - once again :(

DISCUSSION Volker Dierks 10 participants 12 messages Oct 21, 2001 – Oct 23, 2001

lore
Share & tools
lore
#0 lore raw

Hello folks,

my first mail to this famous list .. ;)

OK, 2 month ago, I bought a Abit KG7 MOBO (VIA 686b southbridge) and yesterday I ended up with the second data corruption within these two month.

This one isn't so bad as the first one .. I can't find any 400GB files with the rescue system and also no partition has gone. But on normal system boot, there are errors with rc.S and when kdm normally should start, the system stops to do anything. CTRL+ALT+DEL is configured to reboot the system - when pressed it is going into runlevel 6, but hangs around after that.

I set _no_ special settings with hdparm. hdparm -c -d /dev/hda gives
DMA = 1
32 bit = 1

Some words about my system:
Debian GNU/Linux (sid)
Kernel 2.4.10
Abit KG7 (lite)
Athlon 1.4GHz (step c) Soundblaster Live (value)
1 IBM DTLA 20 GB
Dawicontrol DC-2974 PCI - AM53C974 (CDROM and CDR are SCSI)

I searched 1 hour on google but the only solution seems to be a fix with loadlin and pciset from Thilo <[email protected]>

So my questions is:
I'm going to buy a 3ware 6410(B) IDE raid controller .. can I suspect a failure safe system (in aspect to the 686b problems) when all discs are connected to the 3ware controller?

Greetings from Germany
volker

Signature · 2 lines
GNU/Linux
Let loose the Daemon inside...
#1 lore raw
Quoted 7 lines

So my questions is:
I'm going to buy a 3ware 6410(B) IDE raid controller .. can I suspect a failure safe system (in aspect to the 686b problems) when all discs are connected to the 3ware controller?

I would certainly expect so. I have a Gigabyte GA-7DX with the infamous VIA 686B southbridge...and an SBLive! Value...and I have no IDE devices at all (complete SCSI). I have never encountered data corruption.

Just out of curiosity...is this IBM drive a 75GXP model? What does IBM's Drive Fitness Test tell you about it? I ask because the 75GXP is IMHO a flawed product line.

Kelledin
-----------------
[ Kelledin@Valhalla ~ ] # kill -9 1
init: Just what do you think you're doing, Dave?

#2 lore raw
In reply to Volker Dierks

Hi.

Quoted 3 lines

So my questions is:
I'm going to buy a 3ware 6410(B)
IDE raid controller .. can I suspect

You should be aware of that 3ware is dropping all their IDE RAID controllers so if you want it, buy it fast. They're going out of production. That is... if you want a product that won't be supported RSN.

// Stefan

#3 lore raw
Quoted 4 lines · Stefan Smietanowski

You should be aware of that 3ware is dropping all their IDE RAID controllers so if you want it, buy it fast. They're going out of production. That is... if you want a product that won't be supported RSN.

Eh? This is interesting. I haven't heard of anything like this before, and can't find anything in their website. Maybe you can point me to where you got this bit of information? Rather alarming because I've got a 3ware controller myself.

Thanks.

--> Jijo

--
Federico Sevilla III :: [email protected] Network Administrator :: The Leather Collection, Inc. GnuPG Key: <http://jijo.leathercollection.ph/jijo.gpg>

#4 lore raw
Quoted 4 lines

Eh? This is interesting. I haven't heard of anything like this before, and can't find anything in their website. Maybe you can point me to where you got this bit of information? Rather alarming because I've got a 3ware controller myself.

I heard this straight from a 3ware representative

#5 lore raw
In reply to Federico Sevilla III

Hi.

Quoted 10 lines
Quoted 5 lines

You should be aware of that 3ware is dropping all their IDE RAID controllers so if you want it, buy it fast. They're going out of production. That is... if you want a product that won't be supported RSN.

Eh? This is interesting. I haven't heard of anything like this before, and can't find anything in their website. Maybe you can point me to where you got this bit of information? Rather alarming because I've got a 3ware controller myself.

The Linux XFS development list had a discussion about it a few weeks ago. I even think someone from 3ware joined in or if someone had a quote from someone at 3ware. But just go there and you'll see the site has changed. The only graphic on the front page is now their IP storage thing. The Palisade.

Go to Products on their page. Notice the lack of information on the Escalades.

http://www.3ware.com, but I think you got that already.

Only info on Escalades is:

" Inquires regarding Escalade Storage Switch products should be directed to 650.327.8600 or [email protected]."

and a picture...

// Stefan

#6 lore raw
In reply to Volker Dierks
Quoted 3 lines · Volker Dierks

OK, 2 month ago, I bought a Abit KG7 MOBO (VIA 686b southbridge) and yesterday I ended up with the second data corruption within these two month.

Just so you know I've got an Asus motherboard also with the VIA 686b Southbridge. I'm using 2.4.12-xfs and it's been doing pretty well. I don't use the IDE controller on the drive that often (althoug the kernel is built with support in particlar for the VIA chipset) as it's only for the CD-ROM drive. I have a 3ware 6400 and four IBM hard drives.

First of all the IBM-DTLA-307030 drives are bad. Really bad. I've had one hard drive (of four in hardware RAID5) go down a number of times already. Fortunately the IBM DFT (Drive Fitness Tool) has been able to "repair" the drive and so I'm still using it now.

I also ran into XFS corruption before, but this was because of a firmware bug that got triggered when a drive went down during filesystem activity. I flashed the firmware on the 3ware controller and the problem went away. It had nothing to do with XFS or the kernel (although every 3ware firmware upgrade comes with a driver upgrade and hence a kernel update).

Quoted 3 lines

I'm going to buy a 3ware 6410(B) IDE raid controller .. can I suspect a failure safe system (in aspect to the 686b problems) when all discs are connected to the 3ware controller?

I recommend you get the 7xxx series instead. There are a number of improvements there and you might overall be much happier with that. Especially if you decide to go RAID5, as the 6xxx controller and buffer are too small to do decent RAID5 (so the performance of my system sucks).

RAID is also not "failure safe". You still need regular backups. But it helps because it allows you to recover from small hardware failure that would otherwise have been significant. Like one hard drive going down. Normally I have enough time to pull out the drive (I have a hot swap bay, made in Taiwan or China, and the 3ware controller handles IDE hot swap nicely), plug it in a workstation, reboot with the IBM DFT disk, and fix it. Then I plug the drive back in and rebuild the array on the fly. This whole process takes a few hours, but is hopefully invisible to most users (although performance drops significantly because of the drive activity).

It's hard to get replacements from IBM in my country, though. So if the DFT can't fix a drive some day, I'll just have to replace it. And with RAID5, if any two drives go down at the same time (or one after the other as long as you have more than one drive down), you're still dead. :(

Good luck.

--> Jijo

--
Federico Sevilla III :: [email protected] Network Administrator :: The Leather Collection, Inc. GnuPG Key: <http://jijo.leathercollection.ph/jijo.gpg>

#7 lore raw
In reply to Volker Dierks
Quoted 11 lines · Kelledin Tane
Quoted 7 lines

So my questions is:
I'm going to buy a 3ware 6410(B) IDE raid controller .. can I suspect a failure safe system (in aspect to the 686b problems) when all discs are connected to the 3ware controller?

I would certainly expect so. I have a Gigabyte GA-7DX with the infamous VIA 686B southbridge...and an SBLive! Value...and I have no IDE devices at all (complete SCSI). I have never encountered data corruption.

Corruption *has* been reported on some scsi-only 686b systems, though.

Quoted 3 lines

Just out of curiosity...is this IBM drive a 75GXP model? What does IBM's Drive Fitness Test tell you about it? I ask because the 75GXP is IMHO a flawed product line.

Well, I have a 30GB drive from the 75GXP family. It works just fine so far.

Signature · 2 lines
Vojtech Pavlik
SuSE Labs
#8 lore raw
In reply to Volker Dierks
Quoted 11 lines · Kelledin Tane
Quoted 7 lines

So my questions is:
I'm going to buy a 3ware 6410(B) IDE raid controller .. can I suspect a failure safe system (in aspect to the 686b problems) when all discs are connected to the 3ware controller?

I would certainly expect so. I have a Gigabyte GA-7DX with the infamous VIA 686B southbridge...and an SBLive! Value...and I have no IDE devices at all (complete SCSI). I have never encountered data corruption.

I experienced constant and reproducable data corruption on two via motherboards. One using 686 and one 686b. However, not with the IDe drives. This was with a DDS4 scsi tape drive attached to either a Adaptec or Advansys scsi controller. A 2.5G file dump to tape would never restore the same. One the Adaptec card, I would get 1 or 2 blocks of 64bytes that would differ. On the Advansys it would be 1 or 2 blocks of 63 bytes.

Switch to a PIII-500 on a BX motherboard and have had no problems. The VIA motherboards are now in windows machines where the flakiness of the OS is even worse than the hardware.

Signature · 1 line
-rupa
#9 lore raw
Quoted 4 lines · Rupa Schomaker

Adaptec or Advansys scsi controller. A 2.5G file dump to tape would never restore the same. One the Adaptec card, I would get 1 or 2 blocks of 64bytes that would differ. On the Advansys it would be 1 or 2 blocks of 63 bytes.

Some month ago (about at 2.4.6 kernel) I've got the same problem with my DDS3 (the TAPE CORRUPTION thread). 64 bytes more or less aligned at page boundary. Tought it was the tape driver, it was an Adaptec driver issue (back to when you needed Berkeley DB to compile the firmware)! Now it works perfectly (and I've got an infamous Asus A7V...). BTW no HDD on secondary IDE, only a CDROM :)

-- Lorenzo Marcantonio

#10 lore raw
In reply to Volker Dierks
Quoted 6 lines · Vojtech Pavlik
Quoted 4 lines

I would certainly expect so. I have a Gigabyte GA-7DX with the infamous VIA
686B southbridge...and an SBLive! Value...and I have no IDE devices at all (complete SCSI). I have never encountered data corruption.

Corruption *has* been reported on some scsi-only 686b systems, though.

Right, there were few reports, including mine. As it turned out, disabling MPS 1.4 and probably setting something related to SDRAM (don't remember exactly) fixed the problems.

Signature · 2 lines
Krzysztof Halasa
Network Administrator
#11 lore raw
In reply to Volker Dierks
Quoted 4 lines · Volker Dierks

I searched 1 hour on google but
the only solution seems to be a
fix with loadlin and pciset from
Thilo <[email protected]>

have a look at:

http://www.viahardware.com/686bfaq.shtm
http://www.au-ja.org/review-kt133a-1.phtml (german)

basically you have to find a way to set some specific PCI registers of the northbridge.
check out the write handler of this is /proc/bus/pci/00/00.0 it's at linux/drivers/pci/proc.c:proc_bus_pci_write

basically it looks like you have to seek to the "register" via lseek and then write the control value.
shouldn't be that hard.

in worst case you could write a 20-line linux kernel module to set the few required pci registers.

clemens