2.4.14 fails to boot on a MediaGX
Hi
I've compiled 2.4.14 on a MediaGX running at 133 MHz that I use for a gateway, and am having some difficulty getting it to boot. The last three lines of output are as follows:
Working around Cyrix MediaGX virtual DMA bugs.
CPU: Cyrix MediaGX 3x Core/Bus Clock
Checking 'hlt' instruction... OK.
At this point it locks hard and doesn't respond to Alt-SysRq or Ctrl-Alt-Del. 2.4.10 (the only other 2.4 kernel I have handy) doesn't work either, failing at the same point, although 2.2.19 does boot and run normally.
I'm not on LKML, so please CC me if any further information is required or to test any patches.
Adam
Quoted 3 lines
I've compiled 2.4.14 on a MediaGX running at 133 MHz that I use for a gateway, and am having some difficulty getting it to boot. The last three lines of output are as follows:
What processor did you compile for.
Quoted 3 lines
Working around Cyrix MediaGX virtual DMA bugs.
CPU: Cyrix MediaGX 3x Core/Bus Clock
Checking 'hlt' instruction... OK.
2.4.12-ac was working on my 233Mhz MediaGX. I suspect 2.4.14 does too. I'll give it a test tho
Quoted 5 lines · Alan Cox
Quoted 3 lines
I've compiled 2.4.14 on a MediaGX running at 133 MHz that I use for a gateway, and am having some difficulty getting it to boot. The last three lines of output are as follows:
What processor did you compile for.
Compiled for 486. I remember reading that 586 optimisations (used to?) break the kernel on MediaGXs.
Quoted 7 lines
Quoted 4 lines
Working around Cyrix MediaGX virtual DMA bugs.
CPU: Cyrix MediaGX 3x Core/Bus Clock
Checking 'hlt' instruction... OK.2.4.12-ac was working on my 233Mhz MediaGX. I suspect 2.4.14 does too. I'll give it a test tho
Thanks for the help.
Adam
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
Working around Cyrix MediaGX virtual DMA bugs.
CPU: Cyrix MediaGX 3x Core/Bus Clock
Checking 'hlt' instruction... OK.2.4.12-ac was working on my 233Mhz MediaGX. I suspect 2.4.14 does too. I'll give it a test tho
Thanks for the help.
Ok on my box it boots fine. As an experiment can you build a kerne with no PCI support (Im not saying it'll be useful production wise but it will tell me if its a PCI issue)
Quoted 3 lines · Alan Cox
Ok on my box it boots fine. As an experiment can you build a kerne with no PCI support (Im not saying it'll be useful production wise but it will tell me if its a PCI issue)
And, interestingly enough, it does boot with PCI switched off.
Given that it's a somewhat unusual motherboard, I'm pretty willing to just put an ISA network card in there and write it off as flaky hardware, but it's odd that it boots under 2.2 with PCI support on.
Adam
In article <[email protected]> you write:
Quoted 10 lines · Alan Cox
Quoted 3 lines
Ok on my box it boots fine. As an experiment can you build a kerne with no PCI support (Im not saying it'll be useful production wise but it will tell me if its a PCI issue)
And, interestingly enough, it does boot with PCI switched off.
Given that it's a somewhat unusual motherboard, I'm pretty willing to just put an ISA network card in there and write it off as flaky hardware, but it's odd that it boots under 2.2 with PCI support on.
I have had some problem with the PCI direct probe on a MediaGX CPU, when the probe looked at the CX5530 companion chip the box would reboot. Could you try to only use the PCI BIOS method instead?
PCI support (CONFIG_PCI) [N/y/?] (NEW) y
PCI access mode (BIOS, Direct, Any) [Any] (NEW) BIOS defined CONFIG_PCI_GOBIOS
/Christer
Signature · 1 line
"Just how much can I get away with and still go to heaven?"
Quoted 6 lines · Adam Harvey
Quoted 3 lines · Alan Cox
Ok on my box it boots fine. As an experiment can you build a kerne with no PCI support (Im not saying it'll be useful production wise but it will tell me if its a PCI issue)
Quoted 6 lines
And, interestingly enough, it does boot with PCI switched off.
Given that it's a somewhat unusual motherboard, I'm pretty willing to just put an ISA network card in there and write it off as flaky hardware, but it's odd that it boots under 2.2 with PCI support on.
What kind of motherboard and peripherals are you using? AKAIK the mediagx only supports one external pci busmaster and only on a specific "device".
We are using mediaGXm on ETX and had problems with the wiring of the TVIA CyberPro5050 (combined video+audio controller, audio as busmaster)
Then there are also tweaks in the PCI IDE configuration for mediaGX. Did you enable that?
Quoted 3 lines · Peter Wächtler
What kind of motherboard and peripherals are you using? AKAIK the mediagx only supports one external pci busmaster and only on a specific "device".
I don't know the make of the motherboard without actually pulling the box apart. The system was designed and used in hotels for Internet access in rooms to start with... I picked it up after they were replaced about a year ago.
It's unusual, because it has a PCI chipset, yet only has a couple of ISA slots. I've been enabling PCI mainly out of habit and in case anything on the motherboard was using the bus (apparently not), but I wouldn't be surprised if the PCI chipset is basically broken, since it wasn't really needed.
Quoted 3 lines
We are using mediaGXm on ETX and had problems with the wiring of the TVIA CyberPro5050 (combined video+audio controller, audio as busmaster)
Could be applicable, given that video and audio are handled on-board. I might have to open her up tomorrow and have a poke around.
Quoted 3 lines
Then there are also tweaks in the PCI IDE configuration for mediaGX. Did you enable that?
I've had them on and off, they don't affect the booting problem.
I'll build a kernel using the BIOS access mode (as suggested by Alan) tomorrow and see if that clears it up.
Adam