Skip to contentSkip to conversation

DAC960 oops

DISCUSSION Bill Currie 2 participants 3 messages Nov 19, 2001 – Nov 20, 2001

lore
Share & tools
lore
#0 lore raw

I'm trying to get a DS20 with a Mylex DAC960 up-and-running (boots just fine off the ide drive:) but when I modprobe DAC960, I get the following oops (while ksymoops is moaning about symbols etc, I got the symbols from the exact kernel running (infact, I think it's /still/ running:)):

--8<-----
ksymoops 2.4.0 on alpha 2.4.15-pre5. Options used
-V (default)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.4.15-pre5/ (default) -m /boot/System.map-2.4.15-pre5 (default)

Warning: You did not tell me where to find symbol information. I will assume that the log matches the kernel and modules that are running right now and I'll use the default options above for symbol resolution. If the current kernel and/or modules do not match the log, you can get more accurate output by telling me the kernel version and where to find map, modules, ksyms etc. ksymoops -h explains the options.

Warning (compare_maps): mismatch on symbol partition_name , ksyms_base says fffffc0000996eb0, System.map says fffffc000088a580. Ignoring ksyms_base entry
Warning (compare_maps): mismatch on symbol usb_devfs_handle , usbcore says fffffffc002cf868, /lib/modules/2.4.15-pre5/kernel/drivers/usb/usbcore.o says fffffffc002cf8e8. Ignoring /lib/modules/2.4.15-pre5/kernel/drivers/usb/usbcore.o entry
DAC960: ***** DAC960 RAID Driver Version 2.4.11 of 11 October 2001 *****
DAC960: Copyright 1998-2001 by Leonard N. Zubkoff <[email protected]>
DAC960#0: While configuring DAC960 PCI RAID Controller at
DAC960#0: PCI Bus 0 Device 9 Function 0 I/O Address 0x8080 PCI Address 0xA062000
DAC960#0: FIRMWARE VERSION VERIFICATION FAILED - DETACHING
DAC960#0: Firmware Version = '2.49-0-00'

Unable to handle kernel paging request at virtual address 0000000000000000
modprobe(1634): Oops 0
pc = [<fffffc00008f4220>]  ra = [<fffffc00008f42d8>]  ps = 0000    Not tainted
Using defaults from ksymoops -t elf64-alpha -a alpha
v0 = ffffffffffffffea  t0 = 0000000000000000  t1 = 0000000000000300
t2 = fffffc0000b98890  t3 = fffffc000c188000  t4 = fffffc00006be110
t5 = 0000000000000061  t6 = 000000000046e254  t7 = fffffc000bbb4000
s0 = fffffc0000b48a40  s1 = fffffc0000b48a38  s2 = 0000000000000000
s3 = fffffc0000b8b2e0  s4 = fffffffc0032c488  s5 = 000000012008e970
s6 = 0000000000000006
a0 = fffffc0000b48a38  a1 = 0000000000000000  a2 = 0000000000000001
a3 = 0000000000000001  a4 = 0000000000000000  a5 = 0000000000000000
t8 = ffffffffffffd367  t9 = fffffc000084cbd8  t10= 0000000000000a00
t11= 0000000000000040  pv = fffffc00008f42b0  at = 0000000000000000
gp = fffffc0000b7ea70  sp = fffffc000bbb7d48
Trace:fffffc00008f42d8 fffffc000082f40c fffffc0000810df0 
Code: b75e0000  b59e0020  a6290000  422905a1  f420000f  a59d1ad0 <a4310000> a4510008 
Quoted 1 line
Quoted 1 line

PC; fffffc00008f4220 <__blk_cleanup_queue+40/d0> <=====

Trace; fffffc00008f42d8 <blk_cleanup_queue+28/90> Trace; fffffc000082f40c <sys_init_module+8fc/a40> Trace; fffffc0000810df0 <entSys+a8/c0> Code; fffffc00008f4208 <__blk_cleanup_queue+28/d0> 0000000000000000 <_PC>:
Code; fffffc00008f4208 <__blk_cleanup_queue+28/d0>
0: 00 00 5e b7 stq ra,0(sp)
Code; fffffc00008f420c <__blk_cleanup_queue+2c/d0>
4: 20 00 9e b5 stq s3,32(sp)
Code; fffffc00008f4210 <__blk_cleanup_queue+30/d0>
8: 00 00 29 a6 ldq a1,0(s0)
Code; fffffc00008f4214 <__blk_cleanup_queue+34/d0>
c: a1 05 29 42 cmpeq a1,s0,t0
Code; fffffc00008f4218 <__blk_cleanup_queue+38/d0>
10: 0f 00 20 f4 bne t0,50 <_PC+0x50> fffffc00008f4258 <__blk_cleanup_queue+78/d0>
Code; fffffc00008f421c <__blk_cleanup_queue+3c/d0>
14: d0 1a 9d a5 ldq s3,6864(gp)
Code; fffffc00008f4220 <__blk_cleanup_queue+40/d0> <=====
18: 00 00 31 a4 ldq t0,0(a1) <=====
Code; fffffc00008f4224 <__blk_cleanup_queue+44/d0>
1c: 08 00 51 a4 ldq t1,8(a1)

3 warnings issued. Results may not be reliable.
--8<-----

I should probably mention this is Red Hat 7.1 but with a self-built kernel (I took the RH config file from their kernel-sources rpm and put it in my kernel tree), so I believe gcc 2.96 was involved.

My (wild and uneducated) guess is that the DAC960 hasn't been ported to the current VM. If I knew the kernel better, I would look into it myself (I might anyway:), but any help would be much appreciated.

As I'm not subscribed to lkml, please keep me in the CC list.

TIA
Bill

#1 lore raw
Quoted 4 lines · Bill Currie

I'm trying to get a DS20 with a Mylex DAC960 up-and-running (boots just fine off the ide drive:) but when I modprobe DAC960, I get the following oops (while ksymoops is moaning about symbols etc, I got the symbols from the exact kernel running (infact, I think it's /still/ running:)):

DAC960 calls blk_cleanup_queue on a un-initialized queue, tell Leonard.

Signature · 1 line
Jens Axboe
#2 lore raw
In reply to Bill Currie
Quoted 7 lines · Jens Axboe
Quoted 4 lines · Bill Currie

I'm trying to get a DS20 with a Mylex DAC960 up-and-running (boots just fine off the ide drive:) but when I modprobe DAC960, I get the following oops (while ksymoops is moaning about symbols etc, I got the symbols from the exact kernel running (infact, I think it's /still/ running:)):

DAC960 calls blk_cleanup_queue on a un-initialized queue, tell Leonard.

Thanks, and I'll try to do that once I've got things sorted (I discovered the root cause of the problem was unsupported firmware version, though the oops is unacceptable anyway:).

My current problem is finding out whether I can just pop in new roms with the 3.51 firmware and still have the DEC SRM software still work (KZPSC-UX/KZPAC-XF). The needed sockets are there on the main board but that doesn't mean the DEC firmware will work with 3.51 (the current firmware is 2.49).