erase regions in partitions?

When I create a partition I don't seem to inherit the erase regions from the underlying device. In my case, I have an "amd_flash_x4" (hacked for non-CFI AMD29LV800BB 4-way interleave), which works fine using physmap.

Korva-Markham PCI 32MB @66MHz
CPU revision is: 00000c70
...
Linux version 2.4.16-mips ([email protected]) (gcc version 2.96 20000731 (R1
...
physmap flash device: 400000 at bfc00000
probing amd_flash_x4
Physically mapped flash: Probing for AMD compatible flash Physically mapped flash: Found 1 x 4MiB AMD AM29LV800BT (x4) at 0x0 Korva Flash: Probing for AMD compatible flash
Korva Flash: Found 1 x 4MiB AMD AM29LV800BT (x4) at 0x0
Creating 2 MTD partitions on "Korva Flash":
0x00000000-0x00200000 : "bootstrap and kernel" 0x00200000-0x00400000 : "filesystem"
...

But when I create my own partition layer, viz.:

    static struct mtd_partition korva_partitions[] = {
	    {
		    name: "bootstrap and kernel",
		    size: WINDOW_SIZE / 2,  /* 2M */
		    offset: 0,
	    },{
		    name: "filesystem",
		    size: MTDPART_SIZ_FULL, /* 2M */
		    offset: MTDPART_OFS_APPEND,
	    }
    };
    ...
    mymtd = do_map_probe("amd_flash_x4", &korva_map);

I get:

# cat /proc/mtd                                                                 
    dev:    size   erasesize  name
    mtd0: 00400000 00040000 "Physically mapped flash"  <<-- overlays mtd1&2
    mtd1: 00200000 00040000 "bootstrap and kernel"
    mtd2: 00200000 00040000 "filesystem"

# einfo /dev/mtd/0                      
    Device /dev/mtd/0 has 4 erase regions
    Region 0 is at 0x0 with size 0x40000 and has 0xf blocks
    Region 1 is at 0x3c0000 with size 0x20000 and has 0x1 blocks
    Region 2 is at 0x3e0000 with size 0x8000 and has 0x2 blocks
    Region 3 is at 0x3f0000 with size 0x10000 and has 0x1 blocks
# einfo /dev/mtd/1
    Device /dev/mtd/1 has 0 erase regions
# einfo /dev/mtd/2
    Device /dev/mtd/2 has 0 erase regions

Is this correct for /dev/mtd/1 & for /dev/mtd/2?
I can lay down a JFFS filesystem by:

    # mtd_debug erase /dev/mtd/0 0x200000 0x200000  #(erase 2M starting at 2M)
    # cp jffs.image /dev/mtd/2
    # mount -t jffs /dev/mtdblock/2 /mnt

And all seems well. It just seems funky to not be able to erase /dev/mtd/2 (or any of the non-zero, mtd devices). Originally, I didn't include physmap... then I had no way to erase the parts!

I also discovered that JFFS steals 1M of my 2M flash! Yes, I know I'm stuck with 256K erase size. I picked JFFS1 over JFFS2 because JFFS2 was up front about needed 5 * erase size (1.25M) for its overhead.

Geoff

Geoffrey Espin
[email protected]