Skip to contentSkip to conversation

: RT8139 Too much work at interrupt, IntrStatus=....

BUG Dennis Schoen 3 participants 4 messages Jan 9, 2002 – Feb 26, 2002

lore
Share & tools
lore
#0 lore raw

Hi all,

yesterday I upgraded a firewall/router of a *busy* customer site from version 2.4.7 -> 2.4.17. Only 1-2 seconds after the reboot the network card to the DMZ stopped working. I noticed this messages in /var/log/messages:

Jan  8 17:07:45 liquice kernel: 8139too: rx stop wait too long
Jan  8 17:07:46 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0050.
Jan  8 17:07:46 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0010.
Jan  8 17:07:49 liquice kernel: 8139too: rx stop wait too long
Jan  8 17:07:49 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0001.
Jan  8 17:07:51 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0001.
Jan  8 17:07:57 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0050.
Jan  8 17:07:57 liquice kernel: eth1: Setting 100mbps half-duplex based on auto-negotiated partner ability 40a1.
Jan  8 17:08:09 liquice kernel: NETDEV WATCHDOG: eth1: transmit timed out
Jan  8 17:08:09 liquice kernel: eth1: Setting 100mbps half-duplex based on auto-negotiated partner ability ffff.

after a reboot the same problem occured.

Switching back to v2.4.7 solved the problem so I don't think that it's a hardware issue.

So has anybody an idea whats happening here? Hardware info below. Let me know if you need any additional info.

Thanks
Dennis

liquice:~# lspci
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0305 (rev 03)
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device 8305
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev 40)
00:04.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06)
00:04.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 16)
00:04.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 16)
00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RT8139 (rev 10)
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RT8139 (rev 10)
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RT8139 (rev 10)
00:11.0 Unknown mass storage controller: Promise Technology, Inc.: Unknown device 0d30 (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Rage XL AGP (rev 65)
liquice:~# cat /proc/cpuinfo
processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 6
model           : 4
model name      : AMD Athlon(tm) Processor
stepping        : 2
cpu MHz         : 1210.814
cache size      : 256 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 1
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
bogomips        : 2411.72
#1 lore raw

any reason why you posted that to me and not to the list?

Quoted 5 lines · Mark Hahn
Quoted 1 line

yesterday I upgraded a firewall/router of a *busy* customer site

...

Quoted 1 line
Jan  8 17:07:45 liquice kernel: 8139too: rx stop wait too long

surely a "*busy*" can pay an extra $20 and get a real network card...

sure, but as I said: with kernel v2.4.7 it works! So I guess it must be a bug in something later than version 2.4.7.

Quoted 3 lines
Quoted 1 line
Jan  8 17:07:46 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0050.

did you happen to enable the use of local apic (in the new kernel's config)?

nope. I'll try that.

Dennis

#2 lore raw
In reply to Dennis Schoen
Quoted 16 lines · Dennis Schoen

yesterday I upgraded a firewall/router of a *busy* customer site from version 2.4.7 -> 2.4.17. Only 1-2 seconds after the reboot the network card to the DMZ stopped working. I noticed this messages in /var/log/messages:

Jan  8 17:07:45 liquice kernel: 8139too: rx stop wait too long
Jan  8 17:07:46 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0050.
Jan  8 17:07:46 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0010.
Jan  8 17:07:49 liquice kernel: 8139too: rx stop wait too long
Jan  8 17:07:49 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0001.
Jan  8 17:07:51 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0001.
Jan  8 17:07:57 liquice kernel: eth1: Too much work at interrupt, IntrStatus=0x0050.
Jan  8 17:07:57 liquice kernel: eth1: Setting 100mbps half-duplex based on auto-negotiated partner ability 40a1.
Jan  8 17:08:09 liquice kernel: NETDEV WATCHDOG: eth1: transmit timed out
Jan  8 17:08:09 liquice kernel: eth1: Setting 100mbps half-duplex based on auto-negotiated partner ability ffff.
Quoted 4 lines

after a reboot the same problem occured.

Switching back to v2.4.7 solved the problem so I don't think that it's a hardware issue.

Hi dennis, I'm getting these messages too with an identical card... 8139 (rev 10)... seems to have started happening after I went to 2.4.17... strangely enough I'm getting very similar m�ssages on the machine right beside it.. running 2.4.13, SMP, and a 3com 3c905b (Boomerang).

Anyone have any insight on this one?

Signature · 4 lines
Patrick Cole - Debian Developer <[email protected]>
             - John Curtin, ANU <[email protected]>
             - Linear-G Network Solutions <[email protected]>
             - PGP 1024R/60D74C7D C8E0BC7969BE7899AA0FEB16F84BFE5A   
#3 lore raw
In reply to Dennis Schoen
Quoted 5 lines · Patrick Cole

Hi dennis, I'm getting these messages too with an identical card... 8139 (rev 10)... seems to have started happening after I went to 2.4.17... strangely enough I'm getting very similar mæssages on the machine right beside it.. running 2.4.13, SMP, and a 3com 3c905b (Boomerang).

The problem with the 8139 is the fact that the chip design is really dumb, when I say dumb here, I mean *really* dumb ;-(

The result is that when the card is bombarded with a lot of small packets it can livelock because the queues fill up faster than the kernel code can empty and process them.

I made some changes to improve the situation in the driver, for 2.2 kernels, which I have submitted to Jeff and he plans to integrated them into the next release.

My patched drivers are available from
http://www.wildopensource.com/proj/download/SG_drivers.html however I haven't tested them on 2.4.x, so I am not going to bet on them working.

Cheers,
Jes